Direct IP Idis AL-1112 Operation Manual

Powered by

Alarm
Box

Operation Manual

AL-1112

Before reading this manual

This is a basic installation and operation manual for use of an IDIS alarm box. Users who are using this product for
the rst time, as well as users with experience using comparable products, must read this operation manual carefully
before use and heed to the warnings and precautions contained herein while using the product. Safety warnings
and precautions contained in this operation manual are intended to promote proper use of the product and thereby
prevent accidents and property damage and must be followed at all times. Once you have read this operation manual,
keep it at an easily accessible location for future reference.

• The manufacturer will not be held responsible for any product damage resulting from the use of unauthorized parts and
accessories or from the user’s failure to comply with the instructions contained in this manual.

• The information in this document is believed to be accurate as of the date of publication even though explanation
about some functions may not be incorporated. The manufacturer is not responsible for any problems resulting from
the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this
publication may be issued to incorporate such changes.

• It is recommended that rst-time users of this alarm box and individuals who are not familiar with its use seek technical
assistance from their retailer regarding product installation and use.

• If you need to disassemble the product for functionality expansion or repair purposes, you must contact your retailer and
seek professional assistance.

• Both retailers and users should be aware that this product has been certied as being electromagnetically compatible for
commercial use. If you have sold or purchased this product unintentionally, please replace with a consumer version.

Safety Symbols

Symbol Publication Description

IEC60417, No.5031

Direct current

In-Text

Symbol Type Description

Caution

Note

Important information concerning a specic function.

Useful information concerning a specic function.

2

Safety Precautions

Important Safeguards

Before reading this manual

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

1. Read Instructions

All the safety and operating instructions should be read before the
appliance is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future
reference.

3. Cleaning

Unplug this equipment from the wall outlet before cleaning it. Do not
use liquid aerosol cleaners. Use a damp soft cloth for cleaning.

4. Attachments

Never add any attachments and/or equipment without the approval
of the manufacturer as such additions may result in the risk of re,
electric shock or other personal injury.

5. Water and/or Moisture

Do not use this equipment near water or in contact with water.

6. Placing and Accessories

Do not place this equipment on an wall or ceiling that is not strong
enough to sustain the camera. The equipment may fall, causing
serious injury to a child or adult, and serious damage to the
equipment. Wall or shelf mounting should follow the manufacturer's
instructions, and should use a mounting kit approved by the
manufacturer.

This equipment and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
equipment and cart combination to overturn.

Do not place this equipment in an enclosed space. Sucient
ventilation is required to prevent an increase in ambient temperature
which can cause malfunction or the risk of re.

7. Power Sources

This equipment should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power, please consult your equipment dealer or local power
company.

You may want to install a UPS (Uninterruptible Power Supply)
system for safe operation in order to prevent damage caused by an
unexpected power stoppage. Any questions concerning UPS, consult
your UPS retailer.

This equipment should be remain readily operable.

8. Power Cord

Operator or installer must remove power and TNT connections before
handling the equipment.

9. Lightning

For added protection for this equipment during a lightning storm,
or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the equipment due to lightning
and power-line surges. If thunder or lightning is common where the
equipment is installed, use a surge protection device.

10. Overloading

Do not overload wall outlets and extension cords as this can result in
the risk of re or electric shock.

11. Objects and Liquids

Never push objects of any kind through openings of this equipment
as they may touch dangerous voltage points or short out parts that
could result in a re or electric shock. Never spill liquid of any kind on
the equipment.

12. Servicing

Do not attempt to service this equipment yourself. Refer all servicing
to qualied service personnel.

13. Damage requiring Service

Unplug this equipment from the wall outlet and refer servicing to
qualied service personnel under the following conditions:

A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have hit the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the

operating instructions, adjust only those controls that are covered
by the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive work
by a qualied technician to restore the equipment to its normal

operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance —

this indicates a need for service.

14. Replacement Parts

When replacement parts are required, be sure the service technician
has used replacement parts specied by the manufacturer or that
have the same characteristics as the original part. Unauthorized
substitutions may result in re, electric shock or other hazards.

15. Safety Check

Upon completion of any service or repairs to this equipment, ask the
service technician to perform safety checks to determine that the
equipment is in proper operating condition.

16. Field Installation

This installation should be made by a qualied service person and
should conform to all local codes.

17. Correct Batteries

Warning: Risk of explosion if battery is replaced by an incorrect type.
Replace only with the same or equivalent type.

Dispose of used batteries according to the instructions.
The battery shall not be exposed to excessive heat such as sunshine,

re or the like.

18. Tmra

A manufacturer’s maximum recommended ambient temperature
(Tmra) for the equipment must be specied so that the customer and
installer may determine a suitable maximum operating environment
for the equipment.

3

Before reading this manual

FCC Compliance Statement

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART
15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE
WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE
HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.

WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE
CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS.

WEEE (Waste Electrical & Electronic Equipment)

Correct Disposal of This Product

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government
oce, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal.

Copyright

© 2018 IDIS Co., Ltd.
IDIS Co., Ltd. reserves all rights concerning this manual.
Use or duplication of this manual in part or whole without the prior consent of IDIS Co., Ltd. is strictly prohibited.
Contents of this manual are subject to change without prior notice for reasons such as functionality enhancements.

Registered Trademarks

IDIS is a registered trademark of IDIS Co., Ltd.
Other company and product names are registered trademarks of their respective owners.

This product contains software built partially on open-source content. Codes for the corresponding open-source
content are available for download depending on whether or not the source is publicly available under a license
policy. For more information, refer to System > General page. This product includes software developed by the
University of California, Berkeley and its contributors, and software developed by the OpenSSL Project for use in
the OpenSSL Toolkit (http://www.oepnssl.org/). Also, this product includes cryptographic software written by Eric
Young ([e-mail]).

4

Table of Contents

Part 1 - Remote Setup ........................................6

1

2

Product Features ................................................................6

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Overview .......................................................................6

Part 2 - Remote Setup ........................................9

Protocol .........................................................................9

Remote Setup ...................................................................9

Quick Setup ....................................................................10

System .........................................................................10

General ..................................................................................11

Date/Time ...............................................................................12

User/Group ..............................................................................12

Network .......................................................................13

IP Address ...............................................................................13

Port ......................................................................................14

Security ..................................................................................14

IEEE 802.1X ..............................................................................15

3

Event Action ...................................................................16

Alarm out ................................................................................16

Event ..........................................................................16

Alarm In .................................................................................17

System Event. ............................................................................17

Part 3 - Appendix ...........................................18

Setup Menu Tree (Remote Setup) ...............................................18

Troubleshooting ...............................................................18

Specications ..................................................................19

Index ..........................................................................20

5

Part 1 - Remote Setup

1

2 43 5

Product Features

This alarm box oers the following features:

• DirectIP

• Extend alarm terminal of recording equipment

• Easy connection with network

• Support PoE and DC, AC power

• Check current alarm status via front LED

Accessories

Upon unpacking the product, check the contents inside to ensure that all the following contents are included.

TM

protocol supported

• Alarm Box

• User Guide and Instruction Manual (This document)

• Terminal blocks (4ea)

• Install bracket

• Rubber

Overview

Front Panel

6

Part 1 - Remote Setup

Alarm Out LED

1

Factory Reset Switch

5

Alarm In LED

2

3

1 Alarm Out LED

Displays alarm out status

2 Alarm In LED

Displays alarm in status

3 Power LED

Displays system operating status

4 Network LED

Displays network connection status

LED Status Indications

LED Status Description

Alarm LED On Alarm In/Out operating

O No power connection

Power LED

Blinking System booting or upgrading

On System operating

Power LED

Network LED

4

Network LED Blinking Normal network connection

5 Factory Reset Switch

Use to return all settings to the original factory settings. Connect the power and poke a straightened paperclip into
the factory reset switch hole. Hold the reset switch until the alarm in/out LED blinks several times. Release the reset
switch, and all of the encoder’s settings are now at the original settings it had when it left the factory.

• Factory Reset during system booting: All of the encoder’s settings are now at the original settings it had when
it left the factory.

• Factory Reset during system operating: The other settings except for protocol and system log are now at the
original settings it had when it left the factory.

• Factory Reset via the IDIS Discovery program: The other settings except for protocol, system log and network
settings are now at the original settings it had when it left the factory.

• Factory Reset via the IDIS Discovery program(including network settings) : The other settings except for
protocol and system log are now at the original settings it had when it left the factory.

7