Directed Electronics 571XV User Manual

MMooddeell 557711XXVV
OOwwnneerrss GGuuiiddee
i
© 2005 directed electronics—all rights reserved
lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy
Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), exclud­ing without limitation the siren, the remote transmitters, the associated sensors and acces­sories, which proves to be defective in workmanship or material under reasonable use dur­ing the lifetime of the vehicle provided the following conditions are met: the unit was pro­fessionally installed and serviced by an authorized Directed dealer; the unit will be pro­fessionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: con­sumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote trans­mitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial num­ber is defaced, missing or altered; the unit has been modified or used in a manner con­trary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materi­als or construction. The warranty does not cover damage to the unit caused by installa­tion or removal of the unit. Directed, in its sole discretion, will determine what consti­tutes excessive damage and may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD­ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL­ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM­AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD­ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY
ii
© 2005 directed electronics—all rights reserved
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV­ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON­TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or con­sequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho­rized Directed dealer for details of the plan or call Directed Customer Service at 1-800­876-0800. Directed security systems, including this unit, are deterrents against possible theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft of the automobile, its parts or contents; and hereby expressly disclaims any liability what­soever, including without limitation, liability for theft, damage and/or vandalism. Directed does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
Date of purchaseYour full name and addressAuthorized dealer's company name and addressType of alarm installedYear, make, model and color of the automobileAutomobile license numberVehicle identification numberAll security options installed on automobileInstallation receipts
1
© 2005 directed electronics—all rights reserved
lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ii
wwhhaatt iiss iinncclluuddeedd.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33
iimmppoorrttaanntt iinnffoorrmmaattiioonn.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
22--wwaayy rreemmoottee ddiiaaggrraamm .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 55
ssttaannddaarrdd
rreemmoottee ccoonnffiigguurraattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 55
22--wwaayy rreemmoottee ffuunnccttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
rreemmoottee ooppeerraattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 88
system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
out of range notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
pprrooggrraammmmiinngg rreemmoottee .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1100
uussiinngg yyoouurr ssyysstteemm .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1111
warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
remote start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
rear defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
short-run/turbo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
aauuxxiilliiaarryy oouuttppuuttss ((ooppttiioonnss)) .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. 2233
ssaaffeettyy ffeeaattuurreess.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2244
starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
disabling the remote start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
over and under rev protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ccooddee hhooppppiinngg .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2255
hhiigghh ffrreeqquue
ennccyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. 2266
oowwnneerr rreeccooggnniittiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2266
rraappiidd rreessuummee llooggiicc .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2277
ppoowweerr ssaavveerr mmooddee .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2277
pprrooggrraammmmiinngg
ooppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2288
sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. 2299
gglloossssaarryy ooff tteerrmmss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3311
ttaabbllee ooff ccoonntteennttss
2
© 2005 directed electronics—all rights reserved
3
© 2005 directed electronics—all rights reserved
wwhhaatt iiss iinncclluuddeedd
A control module
An XHF2 receiver/antenna
One 4-button 2-way remote
One 4-button remote
A in-vehicle status LED indicator light
A push-button Valet switch
Your warranty registration
A shut-down toggle switch
iimmppoorrttaanntt iinnffoorrmmaattiioonn
Congratulations on the purchase of your 2-way remote start
keyless entry system. Due to the complexity of this system, it
must be installed by an authorized dealer only. Installation of this
product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with a preprinted dealer certif-
icate to verify that they are authorized.
By carefully reading this Owner's Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing our web site at www.directed.com.
4
© 2005 directed electronics—all rights reserved
your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Make sure you receive the warranty registration from your dealer.
It is also necessary to keep your proof of purchase, which reflects
that the product was installed by an authorized dealer.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
caution
This product is designed for fuel injected, automatic transmission
vehicles only. Use of this product in a standard transmission
vehicle is dangerous and contrary to the product's intended use.
5
© 2005 directed electronics—all rights reserved
22--wwaayy rreemmoottee ddiiaaggrraamm
ssttaannddaarrdd rreemmoottee ccoonnffiigguurraattiioonn
1. Unlock/Lock Indicator (Orange)
2. Receive/Transmit Indicator (Green)
3. Remote Start/Auxiliary Indicator (Yellow)
4. Panic Indicator (Red)
5. Lock Button
6. Unlock Button
7. Remote Start Button
8. Auxiliary Channel Button
2
3
1
5
4
6
78
6
© 2005 directed electronics—all rights reserved
ssyysstteemm mmaaiinntteennaannccee
This system needs no specific maintenance beyond remote
control battery replacement. The remote is powered by a 1.5V
AAA battery.
Low Battery Notification
If the battery is low (and this feature is programmed On) the 2-
way remote will emit 2 long beeps 5-seconds after a transmission
is completed. The 2 long beeps will repeat every 25 seconds up
to 3 times (or until a 2-way remote button is pressed).
Battery Replacement
Gently pull the end of the battery door away from the top of the
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the
remote control observing the correct polarity. When power is
returned the remote control will light all icons and generate
melodies (representing all beeper tones).
22--wwaayy rreemmoottee ffuunnccttiioonnss
The receiver uses a computer-based Learn Routine to learn the
2-way remote buttons. This makes it possible to assign any 2-
way remote button to any receiver function. The 2-way remote
initially comes programmed with Standard Configuration, but
may also be customized by an authorized dealer. The buttons in
all of the instructions in this manual correspond to a Standard
Configuration 2-way remote.
7
© 2005 directed electronics—all rights reserved
standard configuration
Button
Controls the system Lock function by briefly pressing this
button.
Button
Controls the system Unlock function by briefly pressing this
button.
Button
Controls an optional auxiliary function, such as trunk release,
can be controlled by pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
Button
The remote start feature is turned On/Off by pressing this button twice.
and Buttons
The remote start timer mode function of the system is controlled
by pressing these buttons simultaneously.
and Buttons
The Turbo/Short Run feature is controlled by these buttons (refer
to the Turbo/Short Run section for additional details).
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
8
© 2005 directed electronics—all rights reserved
Button
Press and hold this button for 3-seconds to enter Panic Mode.
and and Buttons
When simultaneously pressed these buttons control the rear
window defogger during remote starting.
rreemmoottee ooppeerraattiioonn
The remote start system operates at 434 MHz and incorporates
Directed’s proprietary XHF2 out-board technology transceiver. The
high frequency combined with Binary Data communication achieves
superior range with two-way communication.
system signal paging features
A page is the signal the control module sends to the remote control
as confirmation of receipt of a command or alarm system status.
When the remote control receives a page it will generate a page noti-
fication to the user (notifications are audible beeps) and the LED
Icons will display the current system status.
Command Page
When a command (arm/disarm, remote start, or auxiliary
channel) from the remote control is sent and received, the system
will send a command page back to confirm receipt.
Alarm Page
9
© 2005 directed electronics—all rights reserved
If the ignition is turned on while locked, the system will actuate
the panic feature and an Alarm Page will be sent to the remote
control. When the remote receives this Alarm Page, the remote
control will generate 4 beeps 5 times and the Red LED will illu-
minate for 3-seconds. This will repeat every 100 seconds to alert
the user that the security feature was triggered and will continue
until the alarm page is cleared.
Page Recognition
To clear a page alert/notification, quickly press any button on the
remote control. This can be performed at any time during or after
the page notification has occurred.
The remote control will not send a command to the system at
this time; it will only clear future repeats of the page notification.
The next time a button is pressed on the remote control it will
send a command to the system.
out of range notification
If a command is issued from the remote, but the remote is
beyond the range of the vehicle to receive the command, the
remote responds with 2 sets of 3 quick beeps and the Green LED
will flash 6-times.
10
© 2005 directed electronics—all rights reserved
pprrooggrraammmmiinngg rreemmoottee
To enter programming mode
Press and hold all four remote control buttons simultaneously
until one long beep is heard. Programming mode is now entered.
Beeps On/Off
Press to select beeps On/Off. One beep is notification beeps
On, Two beeps is notification beeps Off. The notification beeps
are programmed On from the factory and can be programmed
Off if they are not desired. When programmed Off the remote
will only flash the LEDs as notification of a command page or an
alarm page.
Remote battery low notification
Press to select low battery notification On/Off. One beep is
low battery notification On. Two beeps is low battery notification
Off. The Low battery Beeps are programmed On from the
factory and can be programmed Off if they are not desired.
When programmed Off the remote will not give any notification
that the battery charge level in the remote is low.
Page notification
The remote control can be programmed to notify the user of a
page (audibly beeping if the vehicle’s status changes, e.g. door
unlocked, engine started, vehicle violation, etc.). Press to
select page On/Off. One beep is page On, Two beeps is page Off.
When programmed off the remote will not give any notification
that a page was received from the vehicle.
11
© 2005 directed electronics—all rights reserved
To exit programming mode
The remote control will exit programming mode after 2-seconds
of inactivity and will emit 2 long beeps.
uussiinngg yyoouurr ssyysstteemm
warning! safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product
must only be performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via
a command signal from the 2-way remote control. Therefore,
never operate the system in an enclosed area or partially
enclosed area without ventilation (such as a garage). When
parking in an enclosed or partially enclosed area or when
having the vehicle serviced, the remote start system must be
disabled using the installed toggle switch. It is the user's sole
responsibility to properly handle and keep out of reach from
children all 2-way remotes to assure that the system does not
unintentionally remote start the vehicle. THE USER MUST
INSTALL A CARBON MONOXIDE DETECTOR IN
OR ABOUT THE LIVING AREA ADJACENT TO THE
VEHICLE. ALL DOORS LEADING FROM ADJACENT
LIVING AREAS TO THE ENCLOSED OR PARTIALLY
ENCLOSED VEHICLE STORAGE AREA MUST AT
12
© 2005 directed electronics—all rights reserved
ALL TIMES REMAIN CLOSED. These precautions are
the sole responsibility of the user.
Use of this product in a manner contrary to its intended
mode of operation may result in property damage, personal
injury, or death. (1) Never remotely start the vehicle with the
vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral
safety feature of the vehicle periodically checked, wherein
the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the
product installation guide. If the vehicle starts in gear, cease
remote start operation immediately and consult with the
authorized Directed dealer to fix the problem.
After the remote start module has been installed, contact
your authorized dealer to have him or her test the remote
start module by performing the Safety Check outlined in the
product installation guide. If the vehicle starts when
performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The
remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle
does not start in gear. All installations must be performed by
an authorized Directed dealer. OPERATION OF THE
REMOTE START MODULE IF THE VEHICLE
STARTS IN GEAR IS CONTRARY TO ITS INTENDED
MODE OF OPERATION. OPERATING THE
13
© 2005 directed electronics—all rights reserved
REMOTE START SYSTEM UNDER THESE CONDI-
TIONS MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE
ASSISTANCE OF AN AUTHORIZED Directed DEALER
TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT
BE HELD RESPONSIBLE OR PAY FOR INSTALLA-
TION OR REINSTALLATION COSTS.
locking
Pressing for one second arms the system by activating the
starter kill and locking the doors (if the door locks are
connected). The horn will honk (if connected) and the parking
lights will flash once to confirm arming of the system. While the
system is armed, the in-vehicle status LED will flash once per
second. The Failsafe
®
Starter Kill will also prevent the vehicle’s
starter from cranking.
The system can also be programmed to arm the optional Failsafe
®
Starter Kill automatically (called Passive Mode). If the system has
been programmed for Passive Mode, the Failsafe
®
Starter Kill will
automatically activate 30 seconds after the ignition has been
turned off. After the ignition has been turned off, the in-vehicle
status LED will flash rapidly to indicate that the system is in
Passive Mode.
14
© 2005 directed electronics—all rights reserved
If Passive Mode has been programmed on, then it is also possible
to program the system for Passive Locking. With Passive Locking,
the vehicle doors lock automatically at the same time that the
Failsafe
®
Starter Kill is activated. If Passive Locking is
programmed on, care must be taken to prevent the keys from
being locked in the vehicle.
The remote responds to active arming with one beep and the
Orange LED will flash 3-times to indicate successful locking of
the system.
If after 2-seconds the remote beeps once, the Orange LED flashes
6-times and the Red LED lights for 3-seconds, the system has
detected an open hood.
unlocking
Pressing for one second disarms the system and unlocks the
doors (if connected). The horn will honk twice (if connected)
and the parking lights will flash twice to confirm disarming of the
system. The optional Failsafe
®
Starter Kill will be deactivated.
The in-vehicle status LED will turn off, unless the system is pro-
grammed for Passive Mode. In Passive Mode, the in-vehicle status
LED will flash rapidly when the system is disarmed. This indi-
cates that the system will re-engage the starter kill and re-lock the
doors (if Passive Locking has been programmed) in 30 seconds
unless the ignition is turned on.
nnoottee::
For Passive Mode to be effective, the Failsafe®
Starter Kill relay must be installed.
15
© 2005 directed electronics—all rights reserved
The remote will indicate unlock notification with 2 beeps and 3
flashes of the Orange LED.
disabling the starter kill without a 2-way remote
If your 2-way remote is lost or damaged, you can manually over-
ride the starter kill. To do this, you must have the vehicle's igni-
tion key and know where the Valet button is located. Be sure to
check with your installer at the time of installation for the loca-
tion of the Valet button.
To override the starter kill, turn
the ignition to the On position.
Press the Valet button once
within 10 seconds. The in-
vehicle in-vehicle status LED will stop flashing and the vehicle should
start. If it does not start you may have waited too long; turn the igni-
tion Off and On and try again.
Location of Valet Button_________________________________
The remote will indicate the starter kill disable notification with
2 beeps and 3 flashes of the Orange LED.
DRW-35
16
© 2005 directed electronics—all rights reserved
panic mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your 2-way remote. Just
press for 3-seconds, and you will enter Panic Mode. The
horn will honk (if connected) and the parking lights (if
connected) will flash for the programmed duration. To stop Panic
Mode at any time, press or on the 2-way remote.
The remote responds with one flash of the Red LED upon
entering Panic Mode and two flashes of the Red LED upon
exiting Panic Mode.
valet mode
You can prevent your system from automatically activating the
Failsafe
®
Starter Kill and locking the doors by using Valet Mode.
This is very useful when washing the vehicle or having it serviced.
In Valet Mode, the starter kill cannot be activated, even with the
2-way remote, but all convenience functions (door locks, remote
start, etc.) will continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition On.
2. Turn the ignition Off.
3. Press and release the Valet
button once within 10 seconds.
nnoottee::
In order for Panic Mode to be effective, the vehicle’s horn (or optional siren) as well as the vehicle’s parking lights must be connected.
DRW-35
17
© 2005 directed electronics—all rights reserved
The in-vehicle status LED will light steadily if you are entering
Valet Mode, and it turn off if you are exiting Valet Mode.
The remote will respond with 3 Orange LED flashes on entering
and 2 beeps and 3 Orange LED flashes on exiting Valet Mode.
remote start
This feature allows you to remotely start and run your vehicle for
a programmable period of time. This makes it possible to warm
up the engine, as well as adjust the interior temperature of the ve-
hicle with the climate control system. If interior heating or
cooling is desired, the climate controls must be preset, and the
fan blower must be set to the desired level prior to remote starting
the vehicle.
To remote start the vehicle:
1. Press on the 2-way remote twice within 3 seconds.
2. The parking lights will flash to confirm that the vehicle will
attempt to start.
3. In gasoline vehicles, the engine will start 4 seconds after the
parking lights flash. In diesel vehicles, the engine will start
when the WAIT-TO-START indicator on the vehicle's dash
goes out.
iimmppoorrttaanntt!!
(1) Never remote start your vehicle when the
keys are in the ignition, except when performing Valet
®
Take-Over, and (2) Never start the vehicle if it is not in either PARK or NEUTRAL.
18
© 2005 directed electronics—all rights reserved
4. Once the vehicle has started, it will run for the pre-program-
med period of time (either 12, 24, or 60 minutes - see
Programming Options section of this guide) or until a shut-
down input is triggered.
For a remote start, the remote responds with remote start tones
and the Yellow LED illuminates for 3-seconds.
For a remote start Off, the remote responds with remote start off
tones and the Yellow LED flashes 3-times.
When you are ready to drive the vehicle:
1. Insert the ignition key and turn
it to the ON (not the START)
position.
2. Press the brake pedal.
While the vehicle is running during remote start operation, the
system will monitor the vehicle and will automatically shut down the
engine if the system receives any of the following shut-down inputs:
The brake pedal is pressed.
The hood is opened.
nnoottee::
If the brake pedal is pressed before the key is in the
ON position, the engine will shut down.
iimmppoorrttaanntt!!
It is unsafe to operate a vehicle’s motor in a garage or other closed off area. Breathing the exhaust from the vehicle is hazardous to your health. Never acti­vate the remote start in an enclosed space.
19
© 2005 directed electronics—all rights reserved
The shutdown toggle button is put into the OFF position.
The pre-programmed run time (12, 24, or 60 minutes) has
elapsed.
2-way remote button is pressed twice again to stop the
engine.
The remote responds with remote start off tones and the
Yellow LED flashes 3-times.
rear defogger
To turn the rear defogger output OFF:
1. Simultaneously press & release the + +
buttons on the remote control.
2. The lights will flash 2 times.
3. The rear defogger output will no longer activate when the
vehicle is remote started.
To turn the rear defogger output ON:
1. Simultaneously press & release the + +
buttons on the remote control.
2. The lights will flash 3 times.
3. The rear defogger output will once again activate when the
vehicle is remote started.
nnoottee::
If the remote start is on the parking lights will turn
off then flash 2-times before returning to their normal
output and the defogger output, if active, will cease.
20
© 2005 directed electronics—all rights reserved
valet take-over
The Valet Take-Over feature allows the vehicle to remain running
after the key has been removed from the ignition. This feature is
useful for occasions when you wish to exit and lock the vehicle
for short periods of time, but would like to leave the motor
running and the climate controls on.
To perform Valet Take-Over:
1. Before turning off the engine, press and release on the 2-
way remote twice within 3 seconds. Then wait five seconds.
2. Turn the ignition key to the OFF position. (The engine will
stay running.)
3. The engine will run until the pre-programmed time elapses
or a shut-down input is received. (See the previous
Remote
Start
section for a complete list of shut-down inputs.)
4. The remote start responds with remote start tones and the
Yellow LED illuminates for 3-seconds.
short-run/turbo
Short run turbo mode keeps the engine running after arriving at
note: This feature will not work if the brake pedal is pressed.
note: If the remote start is on the lights will turn off then flash 3-times before returning to their normal output and the defogger output will activate as programmed.
21
© 2005 directed electronics—all rights reserved
your destination for a programmable period of 1, 3, 5 or 10
minutes. This allows the system’s timer to conveniently cool
down the turbo after you have left the vehicle.
TToo aaccttiivvaattee sshhoorrtt--rruunn//ttuurrbboo::
1. Park the vehicle and set parking
2. Remove your foot from the brake pedal and leave the engine
running.
3. Press and release the and buttons at the same time.
4. The remote start responds with remote start tones and the
Yellow LED is illuminated for 3-seconds.
5. The lights will flash to indicate the remote start has entered
short run turbo mode.
5. Turn off the key, the engine will keep running.
6. Exit and secure the vehicle.
7. The engine will turn off after the programmed run time.
The remote responds with remote start tones and the Yellow LED
illuminates for 3-seconds.
22
© 2005 directed electronics—all rights reserved
timer mode
By pressing the remote and buttons the parking
lights will flash 4 times and then start the vehicle and run for the
set duration. The remote start can be shut off by the 2-way
remote by pressing the remote start button twice and
remain in timer mode, but if any other shut down zones or the
ignition become active the timer mode will cancel.
1. Press Timer mode buttons.
2. The vehicle will confirm with 4 parking light flashes.
3. After a 1-second delay the vehicle will start.
4. The system will start the car and will run for the specified dura-
tion, unless shut down by the remote start button .
5. The system will start every 3 hours (for a maximum of 6
starts) until canceled by the brake, hood, or neutral safety
shut-down wires.
On entering Timer Mode the remote will respond with the Start
On notification. The remote will respond with the Start and Stop
notification during each Start and Stop of the Vehicle while in
Timer mode.
To exit timer mode, turn the ignition switch on any time the
engine is running. The parking lights will flash 4 times, indicat-
ing timer mode has been exited.
important
!!
Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.
23
© 2005 directed electronics—all rights reserved
aauuxxiilliiaarryy oouuttppuuttss ((ooppttiioonnss))
This system also supplies outputs that can control convenience
options such as remote control trunk release and window automa-
tion. Consult your dealer for available options for your system.
Channel 2 Trunk release: When connected, pressing for 1.5
seconds will remotely release the vehicle trunk lid.
Channel 4 auxiliary output: When connected, pressing and
will immediately activate this output to control an
additional convenience option.
The remote will respond with a page notification consisting of an
output tone (once) and the Yellow LED will flash 3-times. This
occurs at the remote after the system has received the command
to activate any of the Auxiliary outputs.
24
© 2005 directed electronics—all rights reserved
ssaaffeettyy ffeeaattuurreess
This system has several important safety features to ensure proper
operation of the motor and prevent accidental damage to the
engine or its components.
starter anti-grind circuitry
Whenever the vehicle is remote started, advanced anti-grind
circuitry prevents the starter from engaging, even if the key is turned
to the start position. This prevents damage to the starter motor if
the key is turned to the start position during remote start operation.
disabling the remote start system
This feature allows your system's remote start unit to be
temporarily disabled to prevent the vehicle from being remote
started accidentally. This feature is useful if the vehicle is being
serviced or stored in an enclosed area. To disable the remote start,
move the shutdown toggle switch to the OFF position. The
switch can be installed in a location of your choice. Check with
your installer for recommended locations.
Location of Shutdown Switch____________________________
note: Anti-grind circuitry only works when the remote start system is operating the motor and the Failsafe® Starter Kill relay is installed.
25
© 2005 directed electronics—all rights reserved
over and under rev protection
The system monitors the engine speed and will automatically
shut the engine off if the RPMs rise above or fall below the
programmed levels. This feature prevents damage to the motor
due to fuel delivery system failures or other problems which may
cause the engine to race.
shut down inputs
This system uses several inputs to shut down the remote start
operation of the motor or prevent remote start if certain inputs are
active. These are the hood and brake inputs. The hood input will
prevent the motor from starting, as well as shut it down, any time
the hood is opened. The brake pedal will shut down the motor at
any time during remote start operation, as well as preventing the
remote start from activating while it is being pressed.
ccooddee hhooppppiinngg
The receiver and 2-way remotes use a mathematical formula
called an algorithm to change their code each time the 2-way
remote is used. This technology has been developed to increase
the security of the unit. The control unit knows what the next codes
should be. This helps to keep the 2-way remote “in sync” with the
note: The system uses a wire connected to the vehicle to sense engine speed. This wire must be connected in order for over and under rev protection to work.
26
© 2005 directed electronics—all rights reserved
control unit even if you use the remote control out of range of the
vehicle. However, if the remote has been pressed many times out
of range of the vehicle, or the battery has been removed, it may fall
out of sync with the control unit and fail to operate the system. To
re-sync the remote simply press several times within range of
the vehicle. The alarm will automatically re-sync and respond to
the 2-way remotes normally.
hhiigghh ffrreeqquueennccyy
Your system transmits and receives at 434 MHz. This provides a
cleaner spectrum with less interference and a more stable signal.
Enjoy a phenomenal increase in range, even in areas with high
radio interference.
oowwnneerr rreeccooggnniittiioonn
Owner Recognition is a revolutionary new feature available only
from Directed. Using a Directed Bitwriter, hand-held program-
ming tool, your dealer can program many of the system settings.
The programmer makes it possible to program different settings
for each 2-way remote that is used with the system. Then, when-
ever a specific 2-way remote is used, the system will recall the
settings assigned to that 2-way remote. Owner Recognition lets
up to four users of the system have different settings that meet
their specific needs. It is almost like having four separate alarms
27
© 2005 directed electronics—all rights reserved
in your vehicle, one for each user.
rraappiidd rreessuummee llooggiicc
This Directed system will store its current state to non-volatile
memory. If power is lost and then reconnected the system will
recall the stored state from memory. This means if the unit is in
Valet Mode and the battery is disconnected for any reason, such
as servicing the car, when the battery is reconnected the unit will
still be in Valet Mode. This applies to all states of the system
including lock, unlock, and Valet Mode.
ppoowweerr ssaavveerr mmooddee
Your system will automatically enter Power Saver Mode while
locked or in Valet Mode, after a period of time in which no oper-
ation has been performed. This lowers the current draw on the
vehicle's battery. Power Saver Mode takes over under the
following conditions:
Power Saver when the system is locked: After the system has
been armed for 24 hours the in-vehicle status LED will flash
at half its normal rate, decreasing the system's current draw.
note: Owner Recognition cannot be programmed with­out a Bitwriter and the necessary software. Check with your dealer for more information.
28
© 2005 directed electronics—all rights reserved
Power Saver in Valet Mode: When the system enters Valet
Mode the in-vehicle status LED illuminates steadily. If the
vehicle is not used (ignition is not turned on) for a one hour
period while the system is in Valet Mode, the status LED will
shut off. If the system remains in Valet Mode, the status LED
will come back on the next time the ignition is turned on and
then back off.
pprrooggrraammmmiinngg ooppttiioonnss
Programming options control your system's normal, operational
set-up. Most options do not require additional parts, but some
may require installation labor.
The following is a list of the programmable options, with the
factory settings in Bold.
The ignition controlled door lock feature
oonn
or off: When
this feature is programmed on, the doors will lock three
seconds after the ignition is turned on, and unlock when the
ignition is turned off. If your installer is programming the
security system with the Directed Bitwriter, ignition lock
and unlock are independent features that can be
programmed separately.
Passive door locking (with passive arming) or
aaccttiivvee ddoooorr
lloocckkiinngg
(only when locking with the 2-way remote). Passive
locking allows the vehicle's doors to lock (after the 30-
29
© 2005 directed electronics—all rights reserved
second countdown). This feature only works if passive
arming has been programmed.
Panic mode
eennaabblleedd
/disabled when the ignition is turned on.
(Some states have laws against sirens sounding in moving cars.)
The engine can be programmed to run when remote started
for any duration ranging from 1 to 60 minutes.
1122 mmiinnuutteess
is the default. After the programmed run time, the engine
will shut down and will not restart, unless in Timer Mode.
3, 6, 9, or 12 minute timer mode run time. Your system can
be programmed to allow the vehicle to run for 3, 6, 9, or 12
minutes when remote started in timer mode. Can be set up
to 16 minutes by your installer.
While the remote start system is running the engine, the
parking lights of the vehicle can
ffllaasshh oonn aanndd ooffff
or come on
and light steadily.
sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnss
Listed below are some of the many expansion options available.
Please consult your dealer for a complete explanation of all the
options available to you.
note: When the system passively arms after one hour, the entry point that has been left open, and anything con­nected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational.
30
© 2005 directed electronics—all rights reserved
Domelight Supervision:
This domelight will illuminate for 30
seconds each time the system is unlocked using the 2-way
remote. This is useful for seeing inside the vehicle at night prior
to entering it.
Power Locks:
This system offers lock outputs that can control
some manufacturers' power door lock systems. For other
systems, additional parts may be required.
Power Trunk Release:
The accessory output of the system can op-
erate a factory power release for the vehicle’s trunk or hatch.
Although the on-board relay can control most power trunk re-
leases, sometimes an optional relay is required. If the factory
release is not power-activated, Directed
®
's 522T trunk release
solenoid can often be added.
Power Window Control:
Automatic power window control is pro-
vided with the 529T and 530T systems. These can operate
power windows, and can roll them up automatically when the
system is armed, roll them down, or both up and down.
Progressive Door Unlocking:
For added security, your system can
be configured to unlock the driver’s door only, leaving the
passengers doors locked. Pressing the unlock button an addi-
tional time will unlock the passenger doors. This option requires
additional parts and labor.
Mobile Video:
This system is compatible with Directed Video’s
MCB1000 Multi-Channel Controller, featuring on-screen secu-
rity system programming and zone trigger information.
31
© 2005 directed electronics—all rights reserved
gglloossssaarryy ooff tteerrmmss
2-Way Remote
: Hand-held, 2-way transceiver which operates the
various functions of your system.
Control Unit:
The “brain” of your system. Usually hidden under-
neath the dash area of the vehicle. The control unit houses the
microprocessor which monitors your vehicle and controls all
system functions.
Failsafe®Starter Kill:
An automatic switch controlled by your
system that prevents the vehicle’s starter from cranking whenever
the system is locked. The vehicle is never prevented from
cranking when the system is unlocked, in Valet
®
Mode, or if the
starter interrupt switch itself fails. Your system has feature-ready
circuitry for the starter interrupt, however installation may
require additional labor.
Input:
A physical connection to the system. An input can be
provided by the hood pinswitch or ignition.
Status LED:
A light mounted at a discretionary location inside
the vehicle. It is used to indicate the status of your system.
Valet®Button:
A small push-button switch mounted at a discre-
tionary location inside the vehicle. It is used to override the
starter interrupt when a 2-way remote is lost or damaged, or to
enter or exit Valet
®
Mode.
32
© 2005 directed electronics—all rights reserved
33
© 2005 directed electronics—all rights reserved
QUICK REFERENCE GUIDE
TToo aarrmm uussiinngg yyoouurr rreemmoottee
To arm the system press for one second. The doors will lock (if con- nected). The LED will begin to flash. The vehicle’s horn (if connected) will honk and the parking lights will flash once to confirm arming.
TToo ddiissaarrmm uussiinngg yyoouurr rreemmoottee
To disarm the system press for one second. The doors will unlock (if connected). The vehicle’s horn (if connected) will honk twice and the parking lights will flash twice.
DDiissaabblliinngg tthhee FFaaiillssaaffee®SSttaarrtteerr KKiillll wwiitthhoouutt aa ttrraannssmmiitttteerr
Turn on the ignition. Press and release the Valet button within 10 sec­onds. The LED will stop flashing and the vehicle should start.
TToo rreemmoottee ssttaarrtt tthhee vveehhiiccllee
Press twice within 3 seconds. The parking lights will turn on (if con- nected) and the vehicle will start and run for the programmed duration.
TToo eenntteerr oorr eexxiitt VVaalleett MMooddee
Turn the ignition to the "ON" position. Turn the ignition back off. Press and release the Valet button within 10 seconds. The status LED will light steadily if you have entered Valet Mode. To exit Valet Mode, repeat the steps above. The LED will turn off when exiting Valet Mode.
TToo aaccttiivvaattee PPaanniicc MMooddee
Press and hold for 1.5 seconds.
TToo aaccttiivvaattee TTiimmeerr MMooddee
Press and to start the vehicle, and run it for the set duration.
TToo aaccttiivvaattee TTuurrbboo MMooddee
Park the vehicle and set parking brake. Remove your foot from the brake pedal and leave the engine running. Press and release the and buttons.
TToo ddiissaabbllee tthhee rreemmoottee ssttaarrtt ssyysstteemm
To disable the remote start, move the shutdown toggle switch to the OFF position.
LLooccaattiioonn ooff SShhuuttddoowwnn SSwwiittcchh____________________________________________________________
CCuutt aalloonngg ddootttteedd lliinnee aanndd ffoolldd ffoorr aa qquuiicckk aanndd eeaassyy rreeffeerreennccee ttoo kkeeeepp iinn yyoouurr ppuurrssee oorr wwaalllleett..
© 2005 directed electronics—a
CCuutt aalloonngg ddootttteedd lliinnee aanndd ffoolldd ffoorr aa qquuiicckk aanndd eeaassyy rreeffeerreennccee ttoo kkeeeepp iinn yyoouurr ppuurrssee oorr wwaalllleett..
VVaalleett TTaakkeeoovveerr
Press and release on the transmitter twice in 3 seconds. Turn the ignition key to the OFF position. Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes).
RReeaarr WWiinnddooww DDeeffooggggeerr
Press the , and buttons simultaneously to turn the defogger on or off when remote starting. When a remote start is initiated, the parking lights will flash 2-times if the defogger is set to off, and will flash 3-times if the defogger is set to on.
The company behind this system is Directed Electronics.
Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America and around the world.
Call
((880000)) 227744--00220000
for more information about our products and services.
Vista, CA 92081
www.directed.com
© 2005 Directed Electronics—All rights reserved
G572V 07-05
Directed Electronics is committed to delivering world class quality products
and services that excite and delight our customers.
Loading...