Directed Electronics 4100 Installation Manual

Download

Page 1

MMooddeell 44110000

IInnssttaallllaattiioonn GGuuiiddee

Page 2

ttaabbllee ooff ccoonntteennttss

Bitwriter™, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention Circuitry®, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics, Inc.

wwhhaatt iiss iinncclluuddeedd .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

wwaarrnniinngg!! ssaaffeettyy ffiirrsstt .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 44

iinnssttaallllaattiioonn ppooiinnttss ttoo rreemmeemmbbeerr .. .. .. .. .. .. .. .. .. .. .. .. .. 55

ffiinnddiinngg tth

hee wwiirreess yyoouu nneeeedd .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66

finding the starter wire . . . . . . . . . . . . . . . . 6

obtaining constant 12V . . . . . . . . . . . . . . . . 6

finding the 12V switched ignition wire . . . . . . 7

finding the accessory wire. . . . . . . . . . . . . . . 7

finding a (+) parking light wire . . . . . . . . . . . 8

finding the wait-to-start bulb wire for diesels . 9

finding the tachometer wire . . . . . . . . . . . . . 9

pprriimmaarryy hhaarrnneessss ((HH11)) wwiirriinngg ddiiaaggrraamm .. .. .. .. .. .

. .. .. .. 1100

44--ppiinn ssaatteelllliittee hhaarrnneessss ddiiaaggrraamm .. .. .. .. .. .. .. .. .. .. .. .. .. 1100

hheeaavvyy ggaauuggee rreellaayy ssaatteelllliittee wwi

irriinngg ddiiaaggrraamm .. .. .. .. .. 1111

ddoooorr lloocckk hhaarrnneessss,, 33--ppiinn ccoonnnneeccttoorr .. .. .. .. .. .. .. .. .. .. 1111

rreemmoottee ssttaarrtt hhaarrnne

essss ((HH22)) wwiirriinngg ddiiaaggrraamm .. .. .. .. .. .. 1111

pprriimmaarryy hhaarrnneessss ((HH11)),, 99--ppiinn ccoonnnneeccttoorr .. .. .. .. .. .. .. .. 1122

rreellaayy k

keeyy sswwiittcchh iinntteerrffaaccee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1166

rreemmoottee ssttaarrtt hhaarrnneessss ((HH22)),, 55--ppiinn ccoonnnneeccttoorr..

.. .. .. .. 1177

nneeuuttrraall ssaaffeettyy sswwiittcchh iinntteerrffaaccee .. .. .. .. .. .. .. .. .. .. .. .. .. 1188

general motors trucks, SUVs, and column . . . .

shifting passenger cars . . . . . . . . . . . . . . . . 20

pre-1996 dodge dakota pickups with 2.5 liter .

motors . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

bbyyppaassssiinngg GGMM vveehhiiccllee aannttii--t

thheefftt ssyysstteemmss .. .. .. .. .. .. ..

((VVAATTSS)) .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2211

11999

955 aanndd nneewweerr vveehhiiccllee aannttii--tthheefftt ssyysstteemmss ((iimmmmoobbii--

lliizzeerrss)) .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. 2222

passkey III (PK-3), transponder-based systems .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

passlock I and passlock II (PL-1 and PL-2) . . 22

ooppttiioonnaall aannttii--ggrriinndd rreellaayy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2233

ddoooorr lloocckk wwiirriinng

g gguuiiddee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2244

type A: (+) 12V pulses from the switch to the .

factory relays . . . . . . . . . . . . . . . . . . . . . . 24

type B: (-) pulses from the switch to the . . . .

factory relays . . . . . . . . . . . . . . . . . . . . . . 25

type C: reversing polarity . . . . . . . . . . . . . . 26

type D: after-market actuators . . . . . . . . . . . 27

type E: mercedes-benz and audi . . . . . . . . . .

(1985 & newer) . . . . . . . . . . . . . . . . . . . . . 27

type F: one-wire system . . . . . . . . . . . . . . . 28

type G: positive (+) multiplex . . . . . . . . . . . 28

type H: negative (-) multiplex . . . . . . . . . . . 29

pprrooggrraammmmiinngg jjuummppeerrss.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. 3300

tach threshold on/off . . . . . . . . . . . . . . . . . 31

light flash (+)/(-) . . . . . . . . . . . . . . . . . . . 31

pplluugg--iinn pprrooggrraamm sswwiittcchh .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3311

ttrraannssmmiitttteerr//rreecceeiivveerr lleeaarrnn rroouuttiinnee .. .. .. .. .. .. .. .. .. .. .. 3322

ttaacchh lleeaarrnniinngg .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3344

to learn the tach signal . . . . . . . . . . . . . . . 34

oppeerraattiinngg sseettttiinnggss lleeaarrnn rroouuttiinnee .. .. .. .. .. .. .. .. .. .. .. .. 3344

ffeeaattuurreess mmeennuu .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. 3366

ffeeaattuurree ddeessccrriippttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3366

sshhuuttddoowwnn ddi

iaaggnnoossttiiccss.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3388

ttiimmeerr mmooddee.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. 3399

ssaaffeettyy cchheecckk .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4400

ttrroouubblleesshhoooottiin

ngg.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4411

wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddee .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. 4433

Page 3

wwhhaatt iiss iinncclluuddeedd

■

TThhee ccoonnttrrooll mmoodduullee ((sseeee ddiiaaggrraamm))

■

TTwwoo AAvviittaall rreemmoottee ttrraannssmmiitttteerrss

■

TThhee pplluugg--iinn pprrooggrraamm sswwiittcchh

■

AA hhoooodd ppiinnsswwiittcchh

■

AA ttooggggllee oovveerrrriiddee sswwiittcchh

■

HHFF++ aanntteennnnaa rreecceeiivveerr

6-pin relay

output

Status LED

2-pin BLUE program plug

4-pin satellite

harness

9-pin main

harness

3-pin/2-wire door lock harness

4-pin/3-wire receiver port

5-pin remote

start harness

Page 4

wwaarrnniinngg!! ssaaffeettyy ffiirrsstt

The following safety warnings must be observed at all times:

■ Due to the complexity of this system, installation of this product must only be performed by an authorized

Directed Electronics dealer.

■ When properly installed, this system can start the vehicle via a command signal from the remote control

transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The fol-

lowing precautions are the sole responsibility of the user; however, authorized Directed Electronics dealers

should make the following recommendations to all users of this system:

1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote

start system must be disabled using the installed toggle switch.

3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote

control transmitters to assure that the system does not unintentionally remote start the vehicle.

TTHHEE UUSSEERR MMUUSSTT IINNSSTTAALLLL AA CCAARRBBOONN MMOONNOOXXIIDDEE DDEETTEECCTTOORR IINN OORR AABBOOUUTT TTHHEE LLIIVVIINNGG AARREEAA AADDJJAACCEENNTT TTOO

THHEE VVEEHHIICCLLEE.. AALLLL DDOOOORRSS LLEEAADDIINNGG FFRROOMM AADDJJAACCEENNTT LLIIVVIINNGG AARREEAASS TTOO TTHHEE EENNCCLLOOSSEEDD OORR PPAARRTTIIAALLLLYY

EENNCCLLOOSSEEDD VVEEHHIIC

CLLEE SSTTOORRAAGGEE AARREEAA MMUUSSTT AATT AALLLL TTIIMMEESS RREEMMAAIINN CCLLOOSSEEDD..

■ Use of this product in a manner contrary to its intended mode of operation may result in property damage,

personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1)

Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the

keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle period-

ically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be

performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this

product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult

with the user to fix the problem immediately.

■ After the remote start module has been installed, test the remote start module in accordance with the Safety

Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown

Circuit test, the remote start unit has not been properly installed. The remote start module must be removed

or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an

authorized Directed Electronics dealer.

OOPPEERRAATTIIOONN OOFF TTHHEE RREEMMOOTTEE SSTTAARRTT MMOODDUULLEE IIFF TTHHEE V

VEEHHIICCLLEE SSTTAARRTTSS IINN

GGEEAARR IISS CCOONNTTRRAARRYY TTOO IITTSS IINNTTEENNDDEEDD MMOODDEE OOFF OOPPEERRAATTIIOONN.. OOPPEERRAATTIINNGG TTHHEE RREEMMOOTTEE SSTTAARRTT SSYYSST

TEEMM UUNNDDEERR

TTHHEESSEE CCOONNDDIITTIIOONNSS MMAAYY RREESSUULLTT IINN PPRROOPPEERRTTYY DDAAMMAAGGEE OORR PPEERRSSOONNAALL IINNJJUURRYY.. IIMMMMEEDDIIAATTEELLYY CCEEAASSEE TTHHEE UUS

SEE

OOFF TTHHEE UUNNIITT AANNDD RREEPPAAIIRR OORR DDIISSCCOONNNNEECCTT TTHHEE IINNSSTTAALLLLEEDD RREEMMOOTTEE SSTTAARRTT MMOODDUULLEE.. DDIIRREECCTTEEDD EELLEECCTTRROONNIICCSS,,

IINNCC.

. WWIILLLL NNOOTT BBEE HHEELLDD RREESSPPOONNSSIIBBLLEE OORR PPAAYY FFOORR IINNSSTTAALLLLAATTIIOONN OORR RREEIINNSSTTAALLLLAATTIIOONN CCOOSSTTSS..

Page 5

iinnssttaallllaattiioonn ppooiinnttss ttoo rreemmeemmbbeerr

IIMMPPOORRTTAANNTT!!

This product is designed for fuel-injected, automatic transmission vehicles only.

Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.

BBeeffoorree bbeeggiinnnniinngg tthhee iinnssttaallllaattiioonn::

■ Please read this entire installation guide before beginning the installation. The installation of this remote

start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or

multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic

probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making con-

nections.

■ Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid

disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their

warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can

require a trip to the dealer.

■ Remove the dome light fuse. This prevents accidentally draining the battery.

■ Roll down a window to avoid being locked out of the vehicle.

AAfftteerr tthhee iinnssttaallllaattiioonn::

■ Test all functions. The "Using Your System" section of the Owner's Guide is very helpful when testing.

■ Complete the vehicle

Safety Check

outlined in this manual prior to the vehicle reassembly.

Page 6

ffiinnddiinngg tthhee wwiirreess yyoouu nneeeedd

IIMMPPOORRTTAANNTT!!

Do not use a 12V test light or logic probe (computer safe test light) to locate these

wires! All testing described in this manual assumes the use of a digital multimeter.

We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant 12V supply

to the ignition switch. Always install a fuse within 12 inches of this connection. If the fuse will also be power-

ing other circuits, such as door locks, a power window module, or a Nite-Lite® headlight control system, fuse

accordingly.

IIMMPPOORRTTAANNTT!!

Do not remove the fuse holder on the red wire. It ensures that the control module has its own fuse, of the proper value, regardless of how many accessories are added to the main power feed.

The starter wire provides 12V directly to the starter or to a relay controlling starter. In some vehicles, it is

necessary to power a cold start circuit. A cold start circuit will test exactly like a starter circuit, but it does not

control the starter. Instead, the cold start circuit is used to prime the fuel injection system for starting when the

vehicle is cold.

HHooww ttoo ffiinndd tthhee ssttaarrtteerr wwiirree wwiitthh yyoouurr mmuullttiimmeetteerr::

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the starter wire. The steering

column is an excellent place to find this wire. Remember you do not

need to interrupt the starter at the same point you test it. Hiding

your starter kill relay and connections is always recommended.

4. Turn the ignition key switch to the start position. Make sure the car

ffiinnddiinngg tthhee ssttaarrtteerr wwiirree

oobbttaaiinniinngg ccoonnssttaanntt 1122VV

Page 7

is not in gear! If your meter reads (+)12V, go to the next step. If it doesn’t, probe another wire.

5. Cut the wire you suspect of being the starter wire.

6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not

turn over, you have the right wire.

The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers

the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).

Accessory wires lose power when the key is in the start position to make more current available to the starter motor.

HHooww ttoo ffiinndd ((++))1122VV iiggnniittiioonn wwiitthh yyoouurr mmuullttiimmeetteerr::

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the ignition wire. The steering

column harness or ignition switch harness is an excellent place to find

this wire.

4. Turn the ignition key switch to the run position. If your meter reads

(+)12V, go to the next step. If it does not read (+)12V, probe another wire.

5. Now turn the key to the start position. The meter display should stay

steady, not dropping by more than a few tenths of a volt. If it drops close

to or all the way to zero, go back to Step 3. If it stays steady at (+)12V, you have found an ignition wire.

An accessory wire will show (+)12V when the key is in the accessory and run positions. It will not show (+)12V

during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The correct

accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for the

blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the

second accessory wire.

ffiinnddiinngg tthhee aacccceessssoorryy wwiirree

ffiinnddiinngg tthhee 1122VV sswwiittcchheedd iiggnniittiioonn wwiirree

Page 8

Most vehicles use a (+) parking light circuit. The (+) parking light wire is often found near the light switch. In

many vehicles the light switch is built into the turn signal lever; in these vehicles the parking light wire can be

found in the steering column. The same wire can often be accessed in the kick panel or running board.

NNOOTTEE::

Many Toyotas and other Asian vehicles, send a (-) signal from the switch to a relay. The relay then sends (+)12V to the bulbs. Whenever you have difficulty finding a (+) parking light wire near the switch, simply test the wires at any switch or control panel that is lit by the instrument panel lighting. Remember, you need a (+) parking light wire that does not vary with the dimmer setting.

HHooww ttoo ffiinndd aa ((++)) ppaarrkkiinngg lliigghhtt ffllaasshh wwiirree wwiitthh yyoouurr mmuullttiimmeetteerr::

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the parking light wire. Usually, the area near the headlight/parking light

switch is an excellent area to start, as is the kick panel.

4. Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights and make sure it goes back

to zero.

5. If it does return to zero, turn the parking lights back on and, using the dash light dimmer control, turn the

brightness of the dash lights up and down. If the meter changes more than a volt when using the dimmer,

look for another wire. If it stays relatively close to (+)12V, you have found your parking light wire.

NNOOTTEE::

Vehicles that use a (-) signal from the switch to the factory relay may be interfaced

directly. (See H1/5 WHITE wire of Primary Harness (H1) Wire Connection Guide section.)

ffiinnddiinngg aa ((++)) ppaarrkkiinngg lliigghhtt wwiirree

Page 9

To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wire will

show between 1V and 6V AC. In multi-coil ignition systems, the system can learn individual coil wires. Individual

coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system

can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the

ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers.

IIMMPPOORRTTAANNTT!!

Do not test tachometer wires using a test light or logic probe. The vehicle will be

damaged.

HHooww ttoo ffiinndd aa ttaacchhoommeetteerr wwiirree wwiitthh yyoouurr mmuullttiimmeetteerr::

1. Set to ACV or AC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Start and run the vehicle.

4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.

5. If this is the correct wire the meter will read between 1V and 6V.

In diesel vehicles it is necessary to interface with the wire that turns on the WAIT-TO-START light in the dash-

board. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out

the vehicle can be started. This wire is always available at the connector leading to the bulb in the dashboard.

It can also be found at the Engine Control Module (ECM) in many vehicles.

TToo tteesstt aanndd ddeetteerrmmiinnee tthhee ppoollaarriittyy ooff tthhiiss w

wiirree::

1. Set your multimeter to DCV or DC voltage (12 or 20V is fine).

2. Attach the (+) probe of the meter to (+)12V.

3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.

4. Turn the ignition switch to the ON position.

5. If the meter indicates 12 volts until the light goes out you have isolated the correct wire and the wire's polar-

ity is negative (ground while the bulb is on).

6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct

wire and the wire's polarity is positive.

ffiinnddiinngg tthhee wwaaiitt--ttoo--ssttaarrtt bbuullbb wwiirree ffoorr ddiieesseellss

ffiinnddiinngg tthhee ttaacchhoommeetteerr wwiirree

Page 10

1100

pprriimmaarryy hhaarrnneessss ((HH11)) wwiirriinngg ddiiaaggrraamm

______

44--ppiinn ssaatteelllliittee hhaarrnneessss ddiiaaggrraamm

______

PPIINNKK IIGGNNIITTIIOONN TTRRIIGGGGEERR

PPUURRPPLLEE SSTTAARRTTEERR TTRRIIGGGGEERR

OORRAANNGGEE AACCCCEESSSSOORRYY TTRRIIGGGGEERR

BBLLUUEE SSTTAATTUUSS OOUUTTPPUUTT

WWHHIITTEE ((++//--)) LLIIGGHHTT FFLLAASSHH

BBLLAACCKK GGRROOUUNNDD

RREEDD//WWHHIITTEE CCHHAANNNNEELL 22 ((VVAALLIIDDIITTYY OONNLLYY))

WWHHIITTEE//RREEDD ((++)) AACCTTIIVVAATTIIOONN IINNPPUUTT

GGRRAAYY//BBLLAACCKK ((--)) WWAAIITT TTOO SSTTAARRTT IINNPPUUTT

WWHHIITTEE//BBLLUUEE ((--)) AACCTTIIVVAATTIIOONN IINNPPUUTT

YYEELLLLOOWW IIGGNNIITTIIOONN OOUUTT ((TTOO AALLAARRMM))

GGRREEEENN//WWHHIITTEE FFAACCTTOORRYY RREEAARRMM

LLIIGGHHTT GGRREEEENN//BBLLAACCKK FFAACCTTOORRYY DDIISSAARRMM

HH11//11

HH11//22

HH11//33

HH11//44

HH11//55

HH11//66

HH11//77

HH11//88

HH11//99

Page 11

1111

hheeaavvyy ggaauuggee rreellaayy ssaatteelllliittee wwiirriinngg ddiiaaggrraamm

______

ddoooorr lloocckk hhaarrnneessss,, 33--ppiinn ccoonnnneeccttoorr

______

RReeffeerr ttoo tthhee DDoooorr LLoocckk WWiirriinngg GGuuiiddee sseeccttiioonn ooff tthhiiss gguuiiddee..

rreemmoottee ssttaarrtt hhaarrnneessss ((HH22)) wwiirriinngg ddiiaaggrraamm

______

BBLLUUEE//WWHHIITTEE ((--)) 220000 mmAA 22NNDD SSTTAATTUUSS//RREEAARR DDEEFFOOGGGGEERR OOUUTTPPUUTT

GGRRAAYY ((--)) HHOOOODD PPIINNSSWWIITTCCHH SSHHUUTTDDOOWWNN WWIIRREE

BBRROOWWNN ((++)) BBRRAAKKEE SSWWIITTCCHH SSHHUUTTDDOOWWNN WWIIRREE

VVIIOOLLEETT//WWHHIITTEE TTAACCHHOOMMEETTEERR IINNPPUUTT WWIIRREE

BBLLAACCKK//WWHHIITTEE ((--)) NNEEUUTTRRAALL SSAAFFEETTYY SSWWIITTCCHH IINNPPUUTT

HH22//11

HH22//22

HH22//33

HH22//44

HH22//55

BBLLUUEE ((--)) UUNNLLOOCCKK OOUUTTPPUUTT

EEMMPPTTYY NNOOTT UUSSEEDD

GGRREEEENN ((--)) LLOOCCKK OOUUTTPPUUTT

RREEDD ((++)) ((3300AA)) HHIIGGHH CCUURRRREENNTT 1122VV IINNPPUUTT

PPIINNKK//WWHHIITTEE ((++)) PPRROOGGRRAAMMMMAABBLLEE OOUUTTPPUUTT FFOORR AACCCCEESSSSOORRYY OORR IIGGNNIITTIIOONN

RREEDD ((++)) ((3300AA)) HHIIGGHH CCUURRRREENNTT 1122VV IINNPPUUTT

OORRAANNGGEE ((++)) ((3300 AAMMPP)) OOUUTTPPUUTT TTOO AACCCCEESSSSOORRYY CCIIRRCCUUIITT

PPUURRPPLLEE ((++)) ((3300 AAMMPP)) OOUUTTPPUUTT TTOO SSTTAARRTTEERR CCIIRRCCUUIITT

PPIINNKK ((++)) ((3300 AAMMPP)) OOUUTTPPUUTT TTOO IIGGNNIITTIIOONN CCIIRRCCUUIITT

Page 12

1122

pprriimmaarryy hhaarrnneessss ((HH11)),, 99--ppiinn ccoonnnneeccttoorr

This wire sends a negative pulse every time the remote start is activated or the doors are unlocked. This can be

used to pulse the disarm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to

the disarm wire as shown in the following diagrams.

RReellaayy ffoorr NNeeggaattiivvee ((--)) DDiissaarrmm WWiirree RReellaayy ffoorr PPoossiittiivvee ((++)) DDiissaarrmm WWiirree

This wire sends a negative pulse every time the remote start shuts down or the doors are locked. This can be

used to pulse the arm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to the

arm wire

AAss aa ssttaanndd--aalloonnee ssyysstteemm::

The H1/3 YELLOW wire should not be connected to anything.

ss aann aadddd--oonn ccaarr ssttaarrtteerr::

If connected, disconnect the ignition/accessory input of the remote controlled secu-

rity or keyless entry system. Connect the H1/3 YELLOW ignition output to the ignition/accessory input of the

remote controlled security or keyless entry system. The wire will prevent the host system from sensing that the

ignition is on during remote start operation.

HH11//33 YYEELLLLOOWW ((++)) iiggnniittiioonn oouuttppuutt ttoo RRFF ssyysstteemm

HH11//22 GGRREEEENN//WWHHIITTEE ffaaccttoorryy rreeaarrmm

HH11//11 LLIIGGHHTT GGRREEEENN//BBLLAACCKK ((--)) ffaaccttoorryy sseeccuurriittyy ddiissaarrmm

Page 13

1133

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2 consecu-

tive ground pulses on the white/blue wire for the remote start to activate or to deactivate. The same holds true

for the remote control activation when set to a two pulse setting it is necessary to press the button twice

for the remote start to activate or deactivate.

NNOOTTEE::

When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed it will affect both activation inputs; the White/Blue wire and the remote control activation.

Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dash-

board. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK can be directly

connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must

be used to change the polarity. (See

Finding the Wires You Need

section for testing procedures.) Here are some

common colors of this wire:

■ Chevrolet and GMC trucks: Light Blue or Dark Blue

■ Ford Trucks: Black/Pink

■ Dodge Ram Trucks: Orange/Black or Black/Orange

NNOOTTEE!!

A 1-amp diode must be installed in line on the factory wire between the wait-to-start

indicator and the ECM. (See the following diagram for details.)

HH11//55 GGRRAAYY//BBLLAACCKK ((--)) ddiieesseell wwaaiitt--ttoo--ssttaarrtt bbuullbb iinnppuutt

HH11//44 WWHHIITTEE//BBLLUUEE rreemmoottee ssttaarrtt ((--)) aaccttiivvaattiioonn iinnppuutt

Page 14

1144

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2 consecu-

tive 12V pulses on the white/blue wire for the remote start to activate or to deactivate. The same holds true for

the remote control activation when set to a two pulse setting it is necessary to press the button twice for

the remote start to activate or deactivate.

NNOOTTEE::

When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed it will affect both activation inputs; the White/Red wire and the remote control activation.

When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the RED/WHITE wire will

supply an output as long as the transmission continues. This is often used to operate a trunk/hatch release or

other relay-driven function.

IIMMPPOORRTTAANNTT!!

Never use this wire to drive anything except a relay or low-current input! The transistorized output

can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current device will

cause it to fail.

HH11//77 RREEDD//WWHHIITTEE CChhaannnneell 22,, ((--)) 220000 mmAA oouuttppuutt

HH11//66 WWHHIITTEE//RREEDD ((++)) aaccttiivvaattiioonn iinnppuutt

Page 15

1155

Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.

(Screws tend to either strip or loosen with time.) We recommend grounding all your components to the same

point in the vehicle.

IIMMPPOORRTTAANNTT::

Do NOT connect this wire to a negative vehicle light flash wire before changing the programming jumper to the negative polarity position or damage to the vehicle light circuit may occur.

As factory configured, the H1/9 WHITE wire should be connected to the (+) parking light wire. If the light flash

polarity jumper is moved to the (-) position (refer to the Programming Jumper section of this guide), this wire

then supplies (-) 200mA output. This is suitable of driving the light control (-) circuits in Toyota, Lexus, BMW

some Mitsubishi, some Mazda, and other models.

NNOOTTEE::

For parking light systems that draw 10 amps or more, the jumper must be placed to the (-) light flash output (refer to the Programming Jumpers section of this guide. P/N 8617 or a standard automotive SPDT relay must be used on the H1/2 light flash output wire.

((++)) PPoossiittiivvee LLiigghhtt FFllaasshh OOuuttppuutt

((--)) LLiigghhtt FFllaasshh OOuuttppuutt

HH11//99 WWHHIITTEE ((++//--)) lliigghhtt ffllaasshh oouuttppuutt

HH11//88 BBLLAACCKK ((--)) cchhaassssiiss ggrroouunndd ccoonnnneeccttiioonn

Page 16

1166

rreellaayy kkeeyy sswwiittcchh iinntteerrffaaccee

The heavy gauge wires leading from the relay satellite are used to energize high current circuits in the vehicle.

It is crucial that these connections are made correctly so that they are capable of handling the current demands.

For this reason, scotch locks, T-taps and other such connectors should not be used.

Remove the two 30 amp fuses prior to connecting these wires and do not replace them until the satellite has

been plugged into the control module. These wires are the source of current for all the circuits the relay satel-

lite will energize. They must be connected to a high current source. Since the factory supplies (+) 12V to the key

switch that is used to operate the motor, it is recommended that these wires be connected there.

NNOOTTEE::

If the factory supplies two separate (+) 12V feeds to the ignition switch, connect one RED wire of the satellite to each feed at the switch.

Connect this wire to the ignition wire in the vehicle. (See

Finding the Wires You Need

section of this guide.)

Connect this wire to the accessory wire in the vehicle that powers the climate control system. (See

Finding the

Wires You Need

section of this guide.)

Connect this wire to the starter wire in the vehicle. (See

Finding the Wires You Need

section of this guide.)

Connect this wire to the second ignition or accessory wire in the vehicle. (Selectable by using Feature 9.)

NNOOTTEE::

For vehicles that do not have a second ignition or accessory wire, this connection is not required.

PPIINNKK//WWHHIITTEE ((++)) oouuttppuutt ttoo sseeccoonndd iiggnniittiioonn//aacccceessssoorryy cciirrccuuiitt

PPUURRPPLLEE ((++)) ssttaarrtteerr oouuttppuutt

OORRAANNGGEE ((++)) aacccceessssoorryy oouuttppuutt

PPIINNKK ((++)) iiggnniittiioonn oouuttppuutt

RREEDD ((22)) ((++))1122VV iinnppuutt ffoorr rreellaayyss

Page 17

1177

rreemmoottee ssttaarrtt hhaarrnneessss ((HH22)),, 55--ppiinn ccoonnnneeccttoorr

Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle

switch to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either in

PARK or NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input MUST rest

at ground in order for the remote start system to operate. Connected properly the vehicle will only start while in PARK

or NEUTRAL.

In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock-out that will not allow the

starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure

B. Connect the other wire from the toggle switch to chassis ground.

FFiigguurree AA FFiigguurree BB

IIMMPPOORRTTAANNTT!!

Always use the Vehicle Safety Check section of this guide to verify that the vehicle

cannot be started in ANY drive gear and that the override switch is functioning properly.

This input provides the module with information about the engine's revolutions per minute (RPMs). It can be

connected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy igni-

tion systems locating a proper signal may be more difficult. (See

Finding the Wires You Need

section of this guide

for finding the tachometer wire.) Once connected, you must teach the system the tach signal. (See

Tach Learning

section of this guide.)

This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake

pedal is depressed. The remote start will be disabled or shut down any time the brake pedal is depressed.

HH22//33 BBRROOWWNN ((++)) bbrraakkee sswwiittcchh iinnppuutt

HH22//22 VVIIOOLLEETT//WWHHIITTEE ttaacchhoommeetteerr iinnppuutt

HH22//11 BBLLAACCKK//WWHHIITTEE nneeuuttrraall ssaaffeettyy sswwiittcchh iinnppuutt

Page 18

1188

This wire MUST be connected to the hood pinswitch. This input will disable or shut down the remote start when

the hood is opened.

This wire supplies a 200mA output as soon as the module begins the remote start process. The H2/5 BLUE/WHITE

wire can also be used to activate the defogger trigger (latched/pulsed) 10 seconds after successful remote start.

(See the

Feature Descriptions

section in this guide for details about programming this output.)

nneeuuttrraall ssaaffeettyy sswwiittcchh iinntteerrffaaccee

Some vehicles combine the column shift mechanism and the mechanical neutral safety switch into one mechan-

ical part. In these vehicles, it is impossible to interface the remote start system before the neutral safety switch.

With this type of vehicle, if the vehicle is left in a drive gear and the remote start system is activated, the vehicle

will move and may cause damage to persons or property.

According to available information, vehicles known to be manufactured this way are most General Motors trucks,

sport utility vehicles and column shifting passenger vehicles. Available information also indicates that pre-1996

Dodge Dakota pickups with 2.5 liter motors are also manufactured this way.

GM vehicles that have the neutral safety switch built into the column shifter can usually be identified by a purple

starter wire. Typically, vehicles that use an outboard mechanical switch use a yellow wire from the ignition switch

to the mechanical switch and a purple wire from the mechanical switch to the starter itself. Remember, this is

only a rule of thumb and is not intended as a substitute for proper testing.

IIMMPPOORRTTAANNTT!!

Please see vehicle Safety Check section of this guide for testing procedures.

HH22//55 BBLLUUEE//WWHHIITTEE ssttaattuuss//ddeeffooggggeerr oouuttppuutt

HH22//44 GGRRAAYY ((--)) hhoooodd ppiinnsswwiittcchh iinnppuutt

Page 19

1199

Vehicles with the neutral safety switch built into the column shifter require that the shifter be placed in park in

order to remove the keys from the ignition. As a result, it is possible to use the key-in-ignition sense switch to

prevent remote starting if the keys are in the ignition. (See

General Motors Trucks, SUVs and Column-Shifting

Passenger Cars

and

Pre-1996 Dodge Dakota Pickups with 2.5 Liter Motors

diagrams in this section on how to

accomplish this.) The first diagram applies to all General Motors vehicles as of the date of this guide’s publica-

tion. The second diagram applies to all pre-1996 Dodge Dakota pickup trucks with 2.5 liter motors. This solution

has one side effect: If the customer inserts the key in the ignition with the driver's door open, the remote start

system will shut down. If this interface is used, it is important to inform the customer that the driver’s door must

be closed before inserting the key into the ignition when the remote start is active. This will allow the customer

to turn the key on and shut the remote start down by pressing the brake, without the key sense wire shutting

down the unit prematurely.

You must also connect the H2/4 BROWN (+) shut-down input to the yellow wire on the relay satellite

ribbon cable. This prevents the remote start system from activating if the key is left in the “run” position. You

must use diodes to isolate the ignition circuit from the brake switch circuit as shown in the diagram below.

IIMMPPOORRTTAANNTT!!

Once the interface is complete, attempt to remote start the vehicle with the door closed and the key in the ignition. The vehicle should not start. If it does, re-check the connections.

As of the date of this guide’s publication, the following list describes the types of vehicles that are known to

have a mechanical neutral safety switch instead of an electrical neutral safety circuit. The model years will vary

from vehicle to vehicle. This list will be updated periodically as new information is available; installers are

encouraged to call DIRECTED Technical Support at 1-800-753-0800 with updated information.

■ Pre-1996 Dodge Dakota pickups with 2.5 liter engines

■ GM "B" Platform: Caprice, Impala SS and Roadmaster

■ GM "D" Platform: Cadillac Fleetwood and Fleetwood Brougham

■ GM "P" Series: Commercial Van

■ GM "L/M" Series: Astro, Safari

■ GM "C/K" Series: Full-size pickup, Sierra, Suburban, Tahoe, Yukon

■ GM "S/T" Series: Blazer, Bravada, Jimmy, pickup, Sonoma

■ GM "G" Series: Express, Savanah

YELLOW WIRE ON RELAY SATELLITE

RIBBON CABLE

(+) BRAKE WIRE

IN VEHICLE

1N4004 DIODE

BROWN (+)

SHUTDOWN INPUT

DIA-154

Page 20

2200

pprree--11999966 ddooddggee ddaakkoottaa ppiicckkuuppss wwiitthh 22..55 lliitteerr mmoottoorrss

ggeenneerraall mmoottoorrss ttrruucckkss,, SSUUVVss,, aanndd ccoolluummnn sshhiiffttiinngg ppaasssseennggeerr ccaarrss

Page 21

2211

bbyyppaassssiinngg GGMM vveehhiiccllee aannttii--tthheefftt ssyysstteemmss ((VVAATTSS))

Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the VATS decoder

module does not measure the proper resistance when the vehicle is started, the starter and fuel pump may be

disabled for up to ten minutes. The system includes a "VATS pack" of resistors. One will match the resistor in the key.

The VATS wires will be two very light-gauge wires coming out of the steering column. The colors of the wires vary,

but they are often contained in orange tubing. Determine the value of the resistor in the key. Then follow the

diagram below to bypass VATS during remote start operation. If the BLUE status output has been programmed for

factory security re-arm, use the BLUE/BLACK Ignition 2 output to control the relay.

NNOOTTEE::

When connecting to the VATS wires, it is not important which wire is cut.

Page 22

2222

11999955 aanndd nneewweerr vveehhiiccllee aannttii--tthheefftt ssyysstteemmss ((iimmmmoobbiilliizzeerrss))

1995 and newer vehicle anti-theft systems (immobilizers) require a bypass module. The bypass module allows for

easy interfacing, while still maintaining the OEM system’s integrity.

The Passlock I and Passlock II systems can be found in the following General Motors vehicles:

■ ‘95 and newer Cavalier and Sunfire

■ ‘96 and newer Achieva, Grand Am, and Skylark

■ ‘97 and newer Intrigue, Malibu, and Cutlass

■ ‘98 and newer trucks, vans, SUVs

■ ‘99 and newer Alero

■ 2000 and newer Impala and Saturn

Passlock I and II systems are VATS-evolved. Passlock systems still rely on the R-code to start, but the pellet is

no longer placed in the key. The resistor can now be found in the key switch. This allows for a greater number

of possible R-codes. In addition, Passlock systems require “seeing” the correct R-code at the correct time. To

bypass Passlock I and II,

pp//nn 555555LL

pp//nn 555555TT

is required.

The Passkey III system can be found in the following vehicles:

■ ‘97 and newer Park Avenue

■ ‘98 and newer Cadillac

■ ‘99 and newer U vans, Transport, Montana, and Silhouette

■ 2000 and newer Grand Prix, Lesabre, Monte Carlo, Lumina, Bonneville

■ 2001 and newer Aurora, Aztek and Rendezvous

Other transponder-based systems include: Acura, BMW, Dodge/Chrysler/Jeep, Ford, Honda, Infinity, Mazda,

Mercedes, Mitsubishi, Nissan, Toyota, Volkswagon, and Volvo.

PK-3 and the transponder-based systems use a transponder system that locks out the ignition and fuel system.

This transponder system is comprised of two parts. The first part, the transceiver, circles the key switch and is

activated when the key is placed in the key switch or turned to the run position. Upon activation, the trans-

ppaasssskkeeyy IIIIII ((PPKK--33)),, ttrraannssppoonnddeerr--bbaasseedd ssyysstteemmss

ppaasssslloocckk II aanndd ppaasssslloocckk IIII ((PPLL--11 aanndd PPLL--22))

Page 23

2233

ceiver will excite the transponder, which is located (but not visible) in the head of the ignition key. The key

transponder will then send a unique code back to the transceiver for evaluation. If the code matches a valid code

of the system, the vehicle will be allowed to start. Most of these transponder-based systems can be bypassed

using

pp//nn 555555UU..

Some may require additional parts from the vehicle manufacturer. Consult you dealer for the

applications. For most Ford PATS transponders,

pp//nn 555555FF

can be used, except for the following vehicles, which

will require

pp//nn 555555UU

: ‘97 and newer Mark VII, and 2000 and newer Taurus/Sable, Contour/Mystique and Focus.

ooppttiioonnaall aannttii--ggrriinndd rreellaayy

The anti-grind relay prevents the starter from engaging if the ignition key is accidentally turned to the start posi-

tion during remote start operation.

Page 24

2244

ddoooorr lloocckk wwiirriinngg gguuiiddee

The blue (H1/8) and green (H1/7) lock wires provide 200mA negative pulses that are used to control electric

door locks. Most common interfaces are described in this section.

The correct wires can usually be found in either kick panel. If you cannot get to the switch, and you find a set

of wires that pulse (+)12V alternately on lock and unlock, you must take care to ensure that it is not a Type C

direct-wire system.

HHeerree iiss aa tteesstt:: CCuutt tthhee wwiirree wwhhiicchh ppuullsseess ((++))1122VV oonn lloocckk,, aanndd tthheenn ooppeerraattee tthhee sswwiittcchh ttoo uunnlloocckk.

■ If all doors unlock, the vehicle uses Type A system.

■ If you lose all door lock operation in both directions, you are operating the master switch in a Type C system.

■ If you lose all door lock operation of one or more doors, but not all motors stop operating, and other doors

still work, you have cut a wire leading directly to one or more motors. You must instead find the actual wires

leading to the switch.

Many domestically-made GM vehicles use Type A locks, while almost all domestically-built Fords are Type C (Ford

builds almost no Type A systems). Chrysler builds both Type A and Type C, so use caution.

WWAARRNNIINNGG!!

Many more GM locks are Type C than in previous years. The full-size pickups (1989up), many of the S10 Blazers, the Corvette, 1995 Cavalier/Sunfire 1993 - and newer, and Camaro/Firebird all use Type C door locks, and cannot be controlled without a 451M!

To interface two relays, a 451M, or a 453T will be required.

ttyyppee AA:: ((++)) 1122VV ppuullsseess ffrroomm tthhee sswwiittcchh ttoo tthhee ffaaccttoorryy rreellaayyss

Page 25

2255

This system is common in many Toyotas, Nissans, Hondas, and Saturns, as well as Ford models with keyless entry

systems (some other Fords also use Type B).

The switch will have three wires on it, and one wire will test ground all the time. One wire will pulse (-) when

the switch locks the doors, and the other wire will pulse (-) when the switch unlocks the doors. This type of

system is difficult to mistake for any other type.

ttyyppee BB:: ((--)) ppuullsseess ffrroomm tthhee sswwiittcchh ttoo tthhee ffaaccttoorryy rreellaayyss

Page 26

2266

Interfacing with a reversing polarity system requires either two relays or one 451M (not included).

It is critical to identify the proper wires and locate the master switch to interface properly. Locate wires that

show voltage on lock and unlock. Cut one of the suspect wires and check operation of the locks from both

switches. If one switch loses operation in both directions and the other switch operates in one direction only,

you have located one of the target wires. The switch that lost all operation is the master switch. If one switch

works both directions and the other switch works only one direction, you have a Type A system. If both switches

still operate, but one or more doors have stopped responding entirely, you have cut a motor lead. Reconnect it

and continue to test for another wire. Once both wires have been located and the master switch identified, cut

both wires and interface as shown below.

IIMMPPOORRTTAANNTT!!

If these are not connected properly, you will send (+)12 volts directly to (-) ground,

possibly damaging the alarm or the factory switch.

ttyyppee CC:: rreevveerrssiinngg ppoollaarriittyy

Page 27

2277

In order for this system to control one or more after-market actuators, a 451M or two relays (optional) are

needed.

Vehicles without factory power door locks require the installation of one actuator per door. This requires mount-

ing the door lock actuator inside the door. Other vehicles may only require one actuator installed in the driver's

door if all door locks are operated when the driver's lock is used. This type of installation is required to operate

factory lock systems in Volvo (except 850), SAAB, and most Mazda, Isuzu and Subaru models.

The fuse used on 12-volt inputs should be 7.5A per motor installed in the vehicle.

IIMMPPOORRTTAANNTT!!

Do not connect the outputs of the alarm directly to the actuator!

This type of door locking system is controlled by an electrically activated vacuum pump; however, the 551R is

not capable of controlling Type E locks.

ttyyppee EE:: mmeerrcceeddeess--bbeennzz aanndd aauuddii ((11998855 && nneewweerr))

ttyyppee DD:: aafftteerr--mmaarrkkeett aaccttuuaattoorrss

Page 28

2288

This system usually requires a negative pulse to unlock, and cutting the wire to lock the door. In some vehicles,

these are reversed. This system is found in late-model Nissan Sentras, some Nissan 240SX, and Nissan 300ZX 1992

and later. It is also found in some Mazda MPV and some Mitsubishi models.

One relay (optional) is used to interface to this type of system as follows:

This system is most commonly found in Ford, Mazda, Chrysler and GM vehicles. The door lock switch or door key

cylinder may contain either one or two resistors. When interfacing with this type of door lock system, two relays

or a Directed Electronics 451M must be used. (See diagram below.)

ttyyppee GG:: ppoossiittiivvee ((++)) mmuullttiipplleexx

ttyyppee FF:: oonnee--wwiirree ssyysstteemm

Page 29

2299

If one resistor is used in the door lock switch/key cylinder, the wire will pulse (+)12V in one direction and less

than (+)12V when operated in the opposite direction.

If two resistors are used in the factory door lock switch/key cylinder, the switch/key cylinder will read less than

(+)12V in both directions.

To determine the resistor values, the door lock switch/key cylinder must be isolated from the factory door lock

system. For all testing, use a calibrated digital multimeter that is set to ohms.

1. Cut the output wire from the door lock switch/key cylinder in half.

2. Test with the meter from the switch side of the cut door lock switch/key cylinder wire to a reliable constant

(+)12V source. Some good constant (+)12V references are the power input source to the door lock switch/key

cylinder, the ignition switch power wire, or the (+) terminal of the battery.

3. Operate the door lock switch/key cylinder in both directions to determine the resistor values. If the multi-

meter displays zero resistance in one direction, no resistor is needed for that direction.

4. Once the resistor value(s) is determined, refer to the wiring diagram for proper wiring.

The system is most commonly found in Ford, Mazda, Chrysler and GM vehicles. The door lock switch or door key

cylinder may contain either one or two resistors.

ttyyppee HH:: nneeggaattiivvee ((--)) mmuullttiipplleexx

ddeetteerrmmiinniinngg tthhee pprrooppeerr rreessiissttoorr vvaalluueess

ttwwoo--rreessiissttoorr ttyyppee

ssiinnggllee--rreessiissttoorr ttyyppee

Page 30

3300

If one resistor is used in the door lock switch/key cylinder, the wire will pulse ground in one direction and resis-

tance to ground when operated in the opposite direction.

If two resistors are used in the factory door lock switch/key cylinder, the door lock switch/key cylinder will read

resistance to ground in both directions.

To determine the resistor values, the door lock switch/key cylinder must be isolated from the factory door lock

system. For all testing, use a calibrated digital multimeter that is set to ohms.

1. Cut the output wire from the door lock switch/key cylinder in half.

2. Test with the meter from the switch side of the cut door lock switch/key cylinder wire to a reliable ground

source. Some good ground references are the ground input source to the door lock switch/key cylinder or the

battery ground.

3. Operate the door lock switch/key cylinder in both directions to determine the resistor values. If the multi-

meter displays zero resistance in one direction, no resistor is needed for that direction.

4. Once the resistor value(s) is determined, refer to the wiring diagram for proper wiring.

pprrooggrraammmmiinngg jjuummppeerrss

ddeetteerrmmiinniinngg tthhee pprrooppeerr rreessiissttoorr vvaalluueess

ttwwoo--rreessiissttoorr ttyyppee

ssiinnggllee--rreessiissttoorr ttyyppee

Page 31

3311

This jumper is used to determine the light flash output polarity. In the (+) position, the on-board relay is enabled

and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board relay is disabled. The

WHITE wire, H1/2, will supply a 200mA (-) output suitable for driving factory parking light relays.

NNOOTTEE::

For parking light circuits that draw 10 amps or more, the internal jumper must be switched

to a (-) light flash output.

PP//NN 88661177

or a standard automotive SPDT relay must be used on the

H1/2 light flash output harness wire.

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their

ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to

the ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehi-

cles. The vehicles affected include many newer Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus,

Stratus, Breeze and LH-based vehicles.

pplluugg--iinn pprrooggrraamm sswwiittcchh

The Program switch plugs into the blue two-pin connector.

ttaacchh tthhrreesshhoolldd oonn//ooffff

lliigghhtt ffllaasshh ((++))//((--))

Page 32

3322

ttrraannssmmiitttteerr//rreecceeiivveerr lleeaarrnn rroouuttiinnee

The system comes with one transmitter that has been taught to the receiver. The receiver can store up to 4 dif-

ferent transmitter codes in memory. Use the following learn routine to add transmitters to the system or to

change button assignments if desired.

The Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to

remember whenever programming this unit: Key, Choose, Transmit and Release.

KKeeyy..

Turn the ignition to the ON position.

CChhoooossee..

Within 10 seconds, press and release the Program switch the number of times cor-

responding to the desired channel listed below. Once you have selected the channel, press

the switch once more and

HHOOLLDD

it. The LED will flash to confirm the selected channel. Do

not release the Program switch.

aauuttoo lleeaarrnn ttrraannssmmiitttteerr ccoonnffiigguurraattiioonn

/ button one .......................lock/unlock

button two .......................Channel 2

button three .....................Remote Start

buttons one and two..........timer mode

/+ button one and three.........turbo start/short run

Page 33

3333

TTrraannssmmiitt..

While

HHOOLLDDIINNGG

the Program switch

, press the button on the transmitter that you

would like to control the selected receiver channel.

RReelleeaassee..

Once the code is learned, the Program switch can be released.

You can advance from programming one channel to another by releasing the Program switch and tapping it to

advance steps and then holding it. For instance: You have programmed Channel One and you want to program

Channel Two. Release the Program switch. Press it one time and release it to advance from Channel One to

Channel Two. Now, press and

HHOOLLDD

the Program switch. The LED will flash two times. As before, do not release

it.

If you want to program Channel Three after programming Channel One, release the Program switch, press it twice

and release it to advance to Channel Three. Then press it once more and

HHOOLLDD

it. The LED will flash three times

to confirm it is ready to receive the code from the transmitter.

LLeeaarrnn RRoouuttiinnee wwiillll bbee eexxiitteedd iiff::

■ Ignition is turned off.

■ Program switch is pressed too many times.

■ More than 25 seconds elapses between programming steps.

CCHHAANNNNEELL NNUUMMBBEERR FFUUNNCCTTIIOONN

1 Auto-Learn

2 Lock/Unlock

3 Channel 2 output

4 Remote Start

5 Turbo/Short Run

6 Timer Mode

7 Delete all Transmitters

Page 34

3344

ttaacchh lleeaarrnniinngg

1. Start the vehicle with the key.

2. Within 5 seconds, press and

HHOOLLDD

the Program switch.

3. The LED will light constant when the tach signal is learned.

4. Release the Program switch.

ooppeerraattiinngg sseettttiinnggss lleeaarrnn rroouuttiinnee

The System Features Learn Routine dictates how the unit operates. The programmable operating settings of this

unit can be changed whenever necessary through the computer-based Learn Routine. The Program push-button

switch, plugged into the blue port, is used together with a programmed transmitter to change the settings. It is

possible to access and change any of the feature settings using the Program switch. To program settings, remem-

ber: Key, Choose, Transmit and Release.

TToo pprrooggrraamm tthhee lleeaarrnn rroouuttiinnee::

KKeeyy..

Turn the ignition on and then back off.

CChhoooossee..

Within 10 seconds, press and release the Program switch the number of times cor-

responding to the feature number you want to program. (See

Features Menu

section.)

Once the Program switch has been pressed and released the desired number of times, press it once more and

HHOOLLDD

it. After a second, the LED will flash to indicate which feature you have accessed. For example, groups of

eight flashes would indicate access to the status output feature (Feature 8).

ttoo lleeaarrnn tthhee ttaacchh ssiiggnnaall

DRW-96

Page 35

3355

TTrraannssmmiitt..

The transmitter is used to select the desired setting. As shipped, the unit is con-

figured to the LED ON settings. These are called the default settings. Pressing Channel One

(usually Button I) will set it to the LED ON setting. The LED will light solid (stop flashing)

to indicate the setting. Pressing Channel 2 (usually Button II) will change the setting to

the LED OFF setting. The LED will go out indicating the change.

RReelleeaassee..

The Program switch can now be released.

You can advance from feature to feature by pressing and releasing the Program switch the number of times nec-

essary to get from the feature you just programmed to the feature you wish to access. For example, if you just

programmed the run time (Feature 3) and you next want to program parking lights (Feature 4) to constant,

release the Program switch. Press and release it once to advance from Feature 3 to Feature 4. Then press it once

more and

HHOOLLDD

it. The LED will flash in groups of 4 to confirm that you have accessed Feature 4.

TThhee lleeaarrnn rroouuttiinnee wwiillll bbee eexxiitteedd iiff aannyy ooff tthhee ffoolllloowwiinngg ooccccuurrss::

■ The ignition is turned on.

■ The Program switch is pressed too many times.

■ More than 25 seconds elapses between programming steps.

Page 36

3366

ffeeaattuurreess mmeennuu

The factory default settings are indicated in

bboolldd

text in the table below.

ffeeaattuurree ddeessccrriippttiioonnss

11 EENNGGIINNEE CCHHEECCKK OONN//OOFFFF::

In the default setting the remote start will monitor either the vehicle's tach wire or

voltage depending on the programming of Feature 2. If programmed off, the vehicle will crank for the pro-

grammed crank time (Feature 5) and will not verify with tach or voltage that the vehicle is running. In the off

setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage

check is always recommended if possible.

FFEEAATTUURREE DDEEFFAAUULLTT -- LLEEDD OONN SSEETTTTIINNGG LLEEDD OOFFFF SSEETTTTIINNGG

NNUUMMBBEERR ((PPRREESSSS CCHHAANNNNEELL 11)) ((PPRREESSSS CCHHAANNNNEELL 22))

EEnnggiinnee cchheecckkiinngg oonn

Engine checking off

TTaacchhoommeetteerr cchheecckkiinngg ttyyppee

Voltage checking type

1122 mmiinnuutteess rruunn ttiimmee ((11))**

24 minutes (2)*, 60 minutes (3) run time

FFllaasshhiinngg ppaarrkkiinngg lliigghhtt oouuttppuutt

Constant parking light output

CCrraannkkiinngg ttiimmee 00..66 sseecc.. ((11))

Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),

1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.

VVoollttaaggee cchheecckk hhiigghh lleevveell

Voltage check low level

SShhoorrtt RRuunn ((ttuurrbboo ttiimmeerr)):: 11 mmiinn

Short Run (turbo timer) 3, 5, 10 minutes

8 Activation pulse: 1 (1)

AAccttiivvaattiioonn ppuullsseess:: 22 ((22))

, 3 (3)

IIggnniittiioonn//aacccceessssoorryy oouuttppuutt:: IIggnniittiioonn

Ignition/accessory output: Accessory

AAcccceessssoorryy ssttaattee dduurriinngg wwaaiitt ttoo ssttaarrtt:: OOFFFF

Accessory state during wait to start: ON

nndd

ssttaattuuss oouuttppuutt:: NNoorrmmaall

Rear defogger latched (2)/pulsed (3)

UUnnlloocckk oouuttppuutt 11 ppuullssee

Unlock output 2 pulses

IIggnniittiioonn lloocckk OONN

Ignition lock OFF

IIggnniittiioonn uunnlloocckk OONN

Ignition unlock OFF

**NNOOTTEE::

The number in parentheses indicate the number of times the LED will flash

Page 37

3377

22 TTAACCHH WWIIRREE SSEENNSSEE//VVOOLLTTAAGGEE SSEENNSSEE::

If the tachometer signal wire is used, this feature must be left in the default

(tach wire connected) setting. If programmed to the voltage sense setting, the unit will crank the starter for a

preset time that can be programmed in Feature 5. Once the starter has been engaged, the system will check the

voltage level to verify the engine is running. The threshold for the voltage level test can be programmed in

Feature 6. When using voltage sense mode, connection of the H2/5 VIOLET/ WHITE tachometer input is not necessary.

33 RRUUNN TTIIMMEE 1122//2244//6600 MMIINNUUTTEESS::

This feature controls how long the engine will run before it “times out” and

shuts down. Programmed to the default setting the engine will run for 12 minutes. If the 24 or 60 minute run

time is desired, change this feature to the two or three flash setting.

44 PPAARRKKIINNGG LLIIGGHHTTSS FFLLAASSHHIINNGG//CCOONNSSTTAANNTT:

In the default setting, the unit will flash the vehicle’s parking lights

while remote started. The constant setting will turn the parking lights on solidly for the entire run duration.

55 CCRRAANNKK TTIIMMEE 00..66//00..88//11..00//11..22//11..44//11..66//11..88//22..00//44..00::

If Feature 2 is programmed to the voltage sense setting,

the crank time must be set to the appropriate duration. The default setting is 0.6 second. If a different crank

time is desired, select Feature 5 and (while pressing the Program switch) press the Channel Two button to

advance through the LED Off settings. The unit will flash the LED to indicate which time is selected. Once the

4.0 second setting is reached the next press of the Channel Two button will reset the system to the shortest

setting.

66 VVOOLLTTAAGGEE CCHHEECCKK LLEEVVEELL HHIIGGHH//LLOOWW::

This feature only functions when Feature 2 is programmed to voltage sense.

Some vehicles have many accessories, which are turned on when remote started. In these vehicles, the variation

of voltage between the engine off and the vehicle running is very slight and the remote start unit may “think”

the vehicle has not started. This can cause the remote start to shut down after the vehicle has been started. If

this is the case, program this feature to the LOW position.

77 SSHHOORRTT RRUUN

N ((TTUURRBBOO TTIIMMEERR))::

When the and buttons on the transmitter are pressed simultaneously

while the engine is running, the vehicle will continue to run for the short run time. The factory default is 1

minute.

88 AACCTTIIVVAATTIIOONN PPUULLSSEE CCOOUUNNTT::

This feature allows the number of pulses to activate the remote start feature to be

changed from 1, 2, or 3 pulses. The pulse count programmed to start the vehicle will also be the same required

to shut down the remote start.

99 22

nndd

IIGGNNIITTIIOONN//AACCCCEESSSSOORRYY OOUUTTPPUUTT::

This will allow the PINK/WHITE to be used as a 2ndignition or a

2ndaccessory.

1100 AACCCCEESSSSOORRYY S

STTAATTEE DDUURRIINNGG WWAAIITT--TTOO--SSTTAARRTT::

This will allow the programming of the accessory wire during the

wait-to-start period of a diesel motor. When ON the accessory comes on when the wait-to-start output is acti-

vated and stays on, dropping out during crank and returning once the car has started. When OFF the accessory

will activate as a normal accessory.

Page 38

3388

1111 22

nndd

SSTTAATTUUSS OOUUTTPPUUTT::

If programmed to status mode, this output will turn on when the remote start is acti-

vated. In defogger mode the output can be programmed to a latched or a pulsed output. When programmed to

the latched output the status will only stay active for 10 minutes.

1122 UUNNLLOOCCKK OOUUTTPPUUTT::

This will program the unlock output to one or two pulses.

1133 IIGGNNIITTIIOONN CCOONNTTRROOLLLLEEDD LLOOCCKK::

When programmed ON the doors will lock when the key is on and all doors are closed.

1144.. IIGGNNIITTIIOONN CCOONNTTRROOLLLLEEDD UUNNL

LOOCCKK::

When programmed ON the doors will unlock automatically when the key is turned

off.

sshhuuttddoowwnn ddiiaaggnnoossttiiccss

The unit has the ability to report the cause of the last shutdown of the remote start system. To enter diagnostic

mode:

1. Turn the ignition off.

2. Press and

HHOOLLDD

the Program switch.

3. Turn the ignition on and then off.

4. Release the Program switch.

5. Press and release the Program switch.

The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns:

Page 39

3399

The LED will stop flashing when the ignition is turned on.

ttiimmeerr mmooddee

By pressing the remote / and buttons simultaneously the parking lights will flash 4 times and

then start the vehicle and run for the set duration. The remote start can be shut off by the transmitter by press-

ing the remote start button and remain in timer mode, but if any other shut down zones or the ignition

becomes active the timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. A 1-second delay will start.

4. The system will start the car and will run for the specified duration, unless shut down by the remote start

button (or the +/- input).

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires (a

maximum of 6 times).

IIMMPPOORRTTAANNTT!!

Timer Mode should be used only in open areas. Never start and run the vehicle in

an enclosed space such as a garage or carport.

LLEEDD SSHHUUTTDDOOWWNN FFLLAASSHHEESS MMOODDEE

One System timed out

Two Over-rev shutdown

Three Low or no RPM

Four Transmitter Shutdown (or optional push-button)

Six (+/-) Shutdown

Seven (-) Neutral safety shutdown (H2/6 BLACK/WHITE)

Eight Wait-to-start timed out

Page 40

4400

ssaaffeettyy cchheecckk

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The fol-

lowing test procedure must be used to verify proper installation and operation of the system. The installation

must be completed before testing, including connection to the brake switch and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the

engine is running, press the brake pedal. The engine should shut down immediately. If the engine continues

to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start

system. The vehicle should not start. If the starter engages, check your hood pin and connections.

NNOOTTEE::

If programmed for Diesel Mode, the system will turn on the ignition, but the starter should

not engage with the hood open.

3. Test the NEUTRAL SAFETY shutdown circuit:

IIMMPPOORRTTAANNTT!!

Make sure there is adequate clearance to the front and rear of the vehicle before

attempting this test.

a. Make sure the hood is closed and no other shutdown circuits are active.

b. Set the emergency brake.

c. Turn the ignition key to the run position but do not start the engine.

d. Put the vehicle in Drive (D).

e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut-

down the remote start system.

f. Activate the remote start system.

■ If the starter engages, immediately step on the brake to shut down the system. If it does engage,

recheck the neutral safety input connection. The vehicle may use a mechanical neutral safety switch.

(See H2/6 BLACK/WHITE neutral safety switch input in

Remote Start Harness Wire Connection Guide

section of this guide.)

■ If the starter does not engage, the test is complete.

Once the system passes all three tests, the vehicle can be re-assembled and delivered. Do not the use the remote

start system or finalize the installation if it fails any of the safety check tests.

Page 41

4411

ttrroouubblleesshhoooottiinngg

■

TThhee iiggnniittiioonn ccoommeess oonn,, bbuutt tthhee ssttaarrtteerr wwiillll nnoott ccrraannkk..

Does it start with the key in the ignition? If so, does the vehicle have a VATS Pass-Key system?

Will it start with the brake pedal depressed? (Make sure to disconnect the brake shutdown when performing this

test.) If so, it may have a brake/starter interlock.

Is the correct starter wire being energized? Check by energizing it yourself with a fused test lead.

■

TThhee ssttaarrtteerr ccrraannkkss ffoorr ssiixx sseeccoonnddss bbuutt d

dooeess nnoott ssttaarrtt..

Either the wrong ignition wire is being energized, the system’s ignition and accessory wires have been connected

backwards, or the vehicle has two ignition circuits. Try activating the unit with the ignition key in the “run”

position. If the vehicle then runs normally, retest your ignition system.

■

TThhee ssttaarrtteerr ccoonnttiinnuueess ttoo ccrraannkk eevveenn tthhoouugghh tthhee eennggiinnee hhaass ssttaarrtteedd..

Has the tach wire been learned? See the

Tach Learning

section of this guide.

Is the tach wire receiving the correct information? Either the wrong tach wire has been used, or a bad connec-

tion exists.

■

TThhee cclliimmaattee ccoonnttrrooll ssyysstteemm ddooeess nnoott wwoorrkk wwhhiillee tthhee uunniitt iiss ooppeerraattiinngg tthhee vveehhiiccllee..

Either the wrong accessory wire is being energized or more than one ignition or accessory wire must be ener-

gized in order to operate the climate control system.

■

TThhee rreemmoottee

ssttaarrtt wwiillll nnoott aaccttiivvaattee..

1. Check harnesses and connections. Make sure the harnesses are fully plugged into the remote start module.

Make sure there are good connections to the vehicle wiring.

2. Check voltage and fuses. Use a meter and check for voltage between the red wire in the 5 pin ribbon harness

and the black ground wire. If you have less than battery voltage, check the 3A and both 30A fuses on the

relay satellite. Also make sure that the ground wire is going to a chassis ground and not to something under

the dash.

3. Check diagnostics. The diagnostics will tell you which shutdown is active or not connected.

■

TThhee rreemmoottee ssttaarrtt wwiillll aaccttiivvaattee bbuutt tthhee ssttaarrtteerr nneevveerr eennggaaggeess..

1. Check for voltage on the purple starter wire two seconds after the remote start becomes active. If there is

voltage present, skip to Step 4. If there is not voltage present, advance to Step 2.

2. Check the 30A fuses.

3. Check diagnostics. If the gray/black wire is detecting ground upon activation, the starter will not crank.

4. Make sure the purple starter wire is connected on the starter side of the optional starter kill relay.

Page 42

4422

5. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to crank if active.

6. Check connections. The two red heavy gauge input wires on the relay satellite should have solid connections.

"T-taps", or "scotch locks" are not recommended for any high current heavy gauge wiring. Also, if the vehicle

has more than one 12-volt input wire, then connect one red wire to each.

■

TThhee vveehhiiccllee ssttaarrttss,, bbuutt iimmmmeeddiiaatteellyy ddiieess..

1. Does the vehicle have an immobilizer? The vehicle’s immobilizer will cut the fuel and/or spark during unau-

thorized starting attempts.

2. Is the remote start programmed for voltage sense? If so, the start time may not be set high enough, or you

may have to adjust the voltage threshold in programming. Voltage sense will not work on some vehicles.

3. Check diagnostics. Sometimes a shutdown will become active during cranking or just after cranking.

■

TThhee vveehhiiccllee ssttaarrttss,, bbuutt tthhee ssttaarrtteerr kkeeeeppss rruunnnniin

ngg..

1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these

features, the engine cranks for the preprogrammed crank time regardless of how long it takes to start the

vehicle to actually start. Adjust to a lower cranking time.

2. Was the Tach Learn successful? The LED must light solidly and brightly to indicate a successful learn.

3. Make sure that there is a tach signal right at the purple/white tach input wire of the remote start. If not,

recheck the connection to the vehicle’s tach wire and make sure the wire is not broken or shorted to ground

leading to the remote start.

■

TThhee vveehhiiccllee wwiillll ssttaarrtt aanndd rruunn oonnllyy ffoorr aabboouutt 1100 sseeccoonnddss..

1. Is the remote start programmed for voltage sense? Try programming the unit for low voltage reference. If this

does not work, a tach wire should be used.

2. Check diagnostics.

■

DDiieesseell vveehhiiccllee ddooeess nnoott wwaaiitt t

too ssttaarrtt..

1. Is the GRAY/BLACK wire connected to the wait-to-start wire of the vehicle?

2. Check the polarity of the wait-to-start wire. (See the

Finding the Wait-to-Start Bulb Wire For Diesels

section

of this guide.)

3. If wiring a negative wait-to-start bulb, make sure that a diode has been placed in line on the factory wire

between the vehicle’s ECM and the wait-to-start bulb. (See wiring description for the

H1/6 GRAY/BLACK (-)

Diesel Wait-To-Start Bulb Input

of the

Primary Harness Wire Connection Guide

Page 43

4433

wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddee

RED 12V high current input

PINK ignition output

VIOLET starter output

BLUE (-) 200mA status output

ORANGE (-) 200mA accessory turn ON

PURPLE (-) 200mA second starter turn ON

PINK (-) 200mA third ignition turn ON

GREEN/BLACK (-) factory alarm disarm

GREEN/WHITE (-) factory alarm rearm

YELLOW (-) ignition output

WHITE/BLUE (-) activation input

GREY/BLACK (-) wait to start input

ORANGE accessory 1 output

RED 12V high current input

PINK/WHITE ignition 2 output

561

BLACK (-) ground input

WHITE/RED (+) activation input

WHITE (+/-) parking light output

GREY hood pin shutdown

BROWN (+) brake shutdown

RED/WHITE (-) 200mA channel 2 output

VIOLET/WHITE tachometer input

BLACK/WHITE neutral safety shutdown

BLUE/WHITE 2nd status output/defogger

Door Locks

Green (-lock)

Blue (-unlock)

Antenna/Receiver

Jumper

LoHi

Status LED

Jumper

Valet/Program button

polarity

light flash

threshold

tachometer

Directed Electronics 4100 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual