Directed Xpresskit dball 2, Xpresskit dball Installation Manual

Platform: DBALL/DBALL2
Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.

Installation Guide

This guide supports the installation of a DBALL in Range Extender Ready (RXT) mode. This solution
supports RF Kit or SmartStart compatibility (both sold separately).

The optional Plug & Play T-Harness THCHD3 (sold separately) provides simpler and faster installation.

Range Extender Ready (RXT) is used to dramatically increase the factory remote start activation range
compared to the factory transmitter. Refer to the Quick Reference Guide for more information.

Important!

This product is ONLY compatible with vehicles equipped with a factory-installed remote starter.

Rev.: 20141117

Index

Vehicle Application Guide......................................................................................................................................................................

Installation

Without T-Harness.................................................................................................................................................................................

With T-Harness THCHD3......................................................................................................................................................................

SmartStart/XL202 Installation Notes.....................................................................................................................................................

Programming

Module Programming............................................................................................................................................................................

Module Reset & Hard Reset..................................................................................................................................................................

Feature and Option List.........................................................................................................................................................................

Feature Programming...........................................................................................................................................................................

LED Diagnostics and Troubleshooting..................................................................................................................................................

Parking Light Error Codes.....................................................................................................................................................................

Limited One-Year Consumer Warranty..................................................................................................................................................

Quick Reference Guide.........................................................................................................................................................................

SmartStart Compatible

SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Range
Extender Ready (RXT) mode without the use of a remote starter. See the Module Programming section for
more information.

02

03
04
05

06
07
08
09

10

11

12
13

® Dodge is a registered trademark and property of its respective company.

© 2014 Directed. All rights reserved.

Platform: DBALL/DBALL2
Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Rev.: 20141117

Page 2

Vehicle Application Guide

The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more
information on installation wiring, programming and troubleshooting for these vehicles.

Vehicles

2015

2014

2013

AV-Panic Mode Activation

AV-Parking Lights Control

DL-Arm Factory Security

DL-Disarm Factory Security

DL-Door Lock Control

DL-Door Unlock

DL-Driver Priority Unlock

DL-Trunk / Hatch Release

EIPS

RS-OEM Remote Start Activation using XL-202 or RF kit

Dodge

Dart (Smart Key) • • • • • • • • • • • • • •

Legend:

AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
EIPS: Engine Idle Protection System
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls

RS-SmartStart

© 2014 Directed. All rights reserved.

Platform: DBALL/DBALL2
Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Installation without T-Harness

OBDII

Diagnostic Connector

Rev.: 20141117

Page 3

(-) Ground: Black, pin 4

1 8

HS CAN Low:

Yellow,

pin 14

HS CAN High: Gray/White, pin 6

169

(+) 12V: Red, pin 16

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

(+) 12V: Red: 13

(-) Ground: Black: 14

14 12 2

10

BCM

under driver dash

(C5 connector)

6

8 9

7

4 5

1 2 3

17 18 19 20 21 22 23 24 25 26 27 28 29 303132

(+) 12V

[1] EIPS Feature: Do not connect these wires if you don’t want to activate this feature.

Fuse 20A

10 11

86 85

15

121314

16

Horn: Gray/Black, pin 30

87

87a

30

[1] (-) EIPS Fail Output: Blue/Red: 12

With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side.

RF

Prog. Button

LED

DBALL/

4

DBALL2

You can connect to either a XL202
RFTD OR a SmartStart module.

Refer to the SmartStart/XL202
Installation Notes for more information.

© 2014 Directed. All rights reserved.

Platform: DBALL/DBALL2
Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Installation with T-Harness THCHD3

Rev.: 20141117

Page 4

OBDII

Diagnostic 16-pin Connector
(vehicle side)

OBDII

T-02

OR

6-pin

Connectors

NOT Used

T-01

These T-Harness connectors are
NOT interchangeable. They will fit
ONLY the appropriate vehicles.

THCHD3 Rev. 1

(Optional T-Harness)

Remote Start Safety

Override Switch

OBDII

OBDII

Diagnostic 16-pin Connector

(vehicle side)

The Remote Start
Safety Override
Switch MUST be in
the ON position.

N/C: Yellow/Red

14 12 2

N/C: Violet/White

N/C: Violet/Brown

N/C: Orange/Black

N/C: Blue/Red

RF

Prog. Button

LED

With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side.

DBALL/

DBALL2

10

4

You can connect to either a XL202
RFTD OR a SmartStart module.

Refer to the SmartStart/XL202
Installation Notes for more information.

© 2014 Directed. All rights reserved.

Platform: DBALL/DBALL2
Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Rev.: 20141117

SmartStart/XL202 Installation Notes

The DBALL Remote Start Ready (RSR) solution offers two (2) configuration options to control your system: RF Kit or
SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202.

SmartStart Revision A

SmartStart is optional and not included. It MUST be purchased separately.

Configuration Wires (White & Brown or Blue)

DBALL/

DBALL2

CABLE

D2D (4 pins, white)

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

SmartStart Revision B

SmartStart is optional and not included. It MUST be purchased separately.

DBALL/

DBALL2

CABLE

D2D (4 pins, white)

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

Cut Brown or Blue Loop

4 pins

2 pins,

not used

Configuration Wires (Gray & White)

Connect Gray wire to (-) Ground

5 pins

4 pins

2 pins,

not used

LED

LED

SmartStart

THIS SIDE UP

OR

Page 5

RF Kit

The optional XL202 and antenna are not included and MUST be purchased separately.

Antenna

DBALL/

LED

DBALL2

XOVER

1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.

2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.

4

XL202

Prog.

Button

4

RF Kit & PKE Combination

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

RF Kit, PKE & SmartStart BT Combination

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

© 2014 Directed. All rights reserved.