Directed Xpresskit dball 2, Xpresskit dball Installation Manual

Page 1

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

Installation Guide

This guide supports the installation of a DBALL in Range Extender Ready (RXT) mode. This solution supports RF Kit or SmartStart compatibility (both sold separately).

The optional Plug & Play T-Harness THCHD3 (sold separately) provides simpler and faster installation.

Range Extender Ready (RXT) is used to dramatically increase the factory remote start activation range compared to the factory transmitter. Refer to the Quick Reference Guide for more information.

Important!

This product is ONLY compatible with vehicles equipped with a factory-installed remote starter.

Rev.: 20141117

Index

Vehicle Application Guide......................................................................................................................................................................

Installation

Without T-Harness.................................................................................................................................................................................

With T-Harness THCHD3......................................................................................................................................................................

SmartStart/XL202 Installation Notes.....................................................................................................................................................

Programming

Module Programming............................................................................................................................................................................

Module Reset & Hard Reset..................................................................................................................................................................

Feature and Option List.........................................................................................................................................................................

Feature Programming...........................................................................................................................................................................

LED Diagnostics and Troubleshooting..................................................................................................................................................

Parking Light Error Codes.....................................................................................................................................................................

Limited One-Year Consumer Warranty..................................................................................................................................................

Quick Reference Guide.........................................................................................................................................................................

SmartStart Compatible

SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Range Extender Ready (RXT) mode without the use of a remote starter. See the Module Programming section for more information.

03 04 05

06 07 08 09

12 13

® Dodge is a registered trademark and property of its respective company.

Page 2

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Rev.: 20141117

Page 2

Vehicle Application Guide

The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles.

Vehicles

2015

2014

2013

AV-Panic Mode Activation

AV-Parking Lights Control

DL-Arm Factory Security

DL-Disarm Factory Security

DL-Door Lock Control

DL-Door Unlock

DL-Driver Priority Unlock

DL-Trunk / Hatch Release

EIPS

RS-OEM Remote Start Activation using XL-202 or RF kit

Dodge

Dart (Smart Key) • • • • • • • • • • • • • •

Legend:

AV: Horn & Lights Controls DL: OE Door Lock & Alarm Controls EIPS: Engine Idle Protection System PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls

RS-SmartStart

Page 3

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Installation without T-Harness

OBDII

Diagnostic Connector

Rev.: 20141117

Page 3

(-) Ground: Black, pin 4

1 8

HS CAN Low:

Yellow,

pin 14

HS CAN High: Gray/White, pin 6

169

(+) 12V: Red, pin 16

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

(+) 12V: Red: 13

(-) Ground: Black: 14

14 12 2

BCM

under driver dash

(C5 connector)

8 9

4 5

1 2 3

17 18 19 20 21 22 23 24 25 26 27 28 29 303132

(+) 12V

[1] EIPS Feature: Do not connect these wires if you don’t want to activate this feature.

Fuse 20A

10 11

86 85

121314

Horn: Gray/Black, pin 30

87a

[1] (-) EIPS Fail Output: Blue/Red: 12

With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side.

Prog. Button

LED

DBALL/

DBALL2

You can connect to either a XL202 RFTD OR a SmartStart module.

Refer to the SmartStart/XL202 Installation Notes for more information.

Page 4

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Installation with T-Harness THCHD3

Rev.: 20141117

Page 4

OBDII

Diagnostic 16-pin Connector (vehicle side)

OBDII

T-02

6-pin

Connectors

NOT Used

T-01

These T-Harness connectors are NOT interchangeable. They will fit ONLY the appropriate vehicles.

THCHD3 Rev. 1

(Optional T-Harness)

Remote Start Safety

Override Switch

OBDII

Diagnostic 16-pin Connector

(vehicle side)

The Remote Start Safety Override Switch MUST be in the ON position.

N/C: Yellow/Red

14 12 2

N/C: Violet/White

N/C: Violet/Brown

N/C: Orange/Black

N/C: Blue/Red

Prog. Button

LED

With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side.

DBALL/

DBALL2

You can connect to either a XL202 RFTD OR a SmartStart module.

Refer to the SmartStart/XL202 Installation Notes for more information.

Page 5

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Rev.: 20141117

SmartStart/XL202 Installation Notes

The DBALL Remote Start Ready (RSR) solution offers two (2) configuration options to control your system: RF Kit or SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202.

SmartStart Revision A

SmartStart is optional and not included. It MUST be purchased separately.

Configuration Wires (White & Brown or Blue)

DBALL/

DBALL2

CABLE

D2D (4 pins, white)

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

SmartStart Revision B

SmartStart is optional and not included. It MUST be purchased separately.

DBALL/

DBALL2

CABLE

D2D (4 pins, white)

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

Cut Brown or Blue Loop

4 pins

2 pins,

not used

Configuration Wires (Gray & White)

Connect Gray wire to (-) Ground

5 pins

4 pins

2 pins,

not used

LED

SmartStart

THIS SIDE UP

Page 5

RF Kit

The optional XL202 and antenna are not included and MUST be purchased separately.

Antenna

DBALL/

LED

DBALL2

XOVER

1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.

2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.

XL202

Prog.

Button

RF Kit & PKE Combination

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

RF Kit, PKE & SmartStart BT Combination

Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.

Page 6

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Module Programming

Refer to the LED Diagnostics section on page 10 for more information and for troubleshooting purposes.

Rev.: 20141117

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.

Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.

Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit

available functions and features.

1. Connect the interface module to your computer using the XKLoader.

2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top left corner of the page.

3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.

4. In the search result page, select Config for RXT, and follow the instructions provided on the screen.

5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.

6. The following message will be displayed when the upload is completed: “The flashing is successfully completed. You may now unplug the kit.” You can now proceed with the programming instructions below.

Page 6

SmartStart Installation

The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.

a. To ensure that the D2D communication between SmartStart and DBALL works properly, the

Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).

b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by

the DBALL D2D connector.

Connect SmartStart to DBALL using the D2D port.

XL202 Installation

Connect XL202 to DBALL using the D2D port.

D2D

10-pin

PANIC

Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.

Press 5 times on the IPB button. The LED flashes orange.

Make sure the RKE (Remote Keyless Entry) is inside the vehicle. Press the Start/Stop button to turn the ignition ON ("RUN" illuminates on Start/Stop switch). The LED is solid orange for 3 seconds.

SmartStart

to RUN

XL202

14-pin

12-pin

Press x5

PUSH

ENGINE

START

STOP

D2D

10-pin

Solid

Flashes

Solid

3 seconds

Turn the ignition OFF.

PUSH

to OFF

ENGINE

START

STOP

Page 7

Platform: DBALL/DBALL2 Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Rev.: 20141117

Page 7

Module Reset

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

14-pin

12-pin

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

D2D

10-pin

Wait 3 seconds until the LED turns ON solid orange then release the

programming button. The LED turns ON solid red.

& &

Solid

Release

Solid

Hard Reset

Warning Against Executing a Hard Reset!

A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

D2D

10-pin

Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.

Solid

14-pin

12-pin

Flashes

Release the programming button. The LED turns ON solid red.

Release

Solid

Page 8

Platform: DBALL/DBALL2

* Default option

Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Feature and Option List

It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.

Fea t. Operation Flashes / Option Description

1 RF Output Type

Unlock Driver Priority

Heated Seats

Defroster

Heated Seats/Defroster Temperature Control

Heated Seats Temperature Level

Automatic Controlled Door Lock

Rev.: 20141117

1. Disabled* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.

2. All Unlocks all doors on first press.

1. Disabled*

2. Enabled

1. Disabled*

2. Enabled

1. 32° F (0° C)*

2. 23° F (-5° C)

3. 41° F (5° C)

4. Always ON

1. High*

2. Low

1. Disabled* No operation.

2. With Ignition Locks all doors when ignition is ON. Unlocks all doors when ignition turns OFF.

3. With Brake

4. With Speed Not available

1. Disabled

2. Normal

N/A

Locks all doors when brake pedal is pressed while the vehicle is running. Unlocks all doors when ignition turns OFF.

The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.

Smart OEM Alarm Control will behave like a s tandard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown.

Page 8

Smart OEM

Alarm Control

3. Enabled*

Smart OEM Alarm Control will sy nchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user.

Page 9

Platform: DBALL/DBALL2

Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Feature Programming

To enter feature programming routine

Turn the ignition ON, then OFF.

Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the Programming button.

The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the

current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.

Changing feature options

Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.

The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly

the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature

Press and release the programming button a number of times to advance from the current feature to the next desired feature.

The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed

Other features can be programmed.

The feature programming can be exited.

Programming

Button

Rev.: 20141117

Page 9

Exiting feature programming

No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence. OR

Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.

Page 10

Platform: DBALL/DBALL2

LED Status Description Trouble shooting

Module progra mming - Error codes

LED Description Trouble shooting Comment

Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

LED Diagnostics & Troubleshooting

Module programming - Firmw are specific

Rev.: 20141117

Page 10

Solid

Flashes

Solid

Flashes red x2

Flashes red x3

Solid red Waiting for module programming. Press 5 times on programming button. See module programming section.

Flashes green fas t

Flashes orange quickly

Solid orange for 3 seconds

CAN not detected.

Bypass data not detected.

Normal. CAN programmed and w aiting for bypass programming.

Module in RXT mode w aiting for Ignition.

Module successef ully programmed in RXT. Normal operation

Check the Tan - Tan/Black w ire connections. Wake up the data bus by turning the ignition on and try again.

Module not in RXT. Press 5 times on programming button before turning ignition ON. See module programming.

Normal operation

Check f or CAN-High and CAN-Low connections as the Ignition is not seen CAN.

Make sure the battery w as removed w hen turning the ignition ON.

Page 11

Platform: DBALL/DBALL2

LED Description Troubleshooting Comment

External module synchronization

LED Description Troubleshooting Comment

RXT Code

Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Diagnostic OBDII BUS statuses like DTC codes

Diagnostic OBDII f eature not

(Flashes red, red, then orange) x 10

initialized.

D2D and W 2W commands

Flashes orange x 1

LOCK command received.

w ill not be available on SmartStart because the BUS w as not detected. Please chec k your HSCAN connections, reset, and reprogram the module.

SmartStart can still be used but will w ork with limited statuses.

Rev.: 20141117

Page 11

Flashes orange x 2

Flashes orange x 3

Flashes green x7

Flashes green x8

Flashes red x 5 Start failed.

Flashes red x 6 Stop failed.

Flashes red x 7 RFTD disabled.

Flashes red x 8 OEM RS disabled.

UNLOCK command received.

TRUNK command received.

Start command received.

Stop command received.

If the bypass module fails to flash, it means the module did not receive the signal.

RXT start command not executed.

OEM Remote Start Ac tivation w as attempted w hen RFTD feature is disabled.

RXT start not possible w hen OEM sys tem is disabled.

Commands can come from RF, D2D or W2W.

If using XL202, make sure that the proper cable is connected. When using SmartStart make sure that SmartStart is conf igured in D2D.

Module received the command, but the car did not perform the action.

Activated from Web automatically w hen using RXT flash tool or can be done manually. Refer to f eature programming section for more information.

Refer to the ow ner documentation to activate it.

Page 12

Platform: DBALL/DBALL2

Firmware: CHRYSLER7 Range Extender Ready (RXT) Installation

Rev.: 20141117

Page 12

Limited One Year Consumer Warranty

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Page 13

Quick Reference Guide

DBALL/DBALL2-CHRYSLER7 Range Extender Ready (RXT) Installation

Range Extender Ready (RXT) is used to amplify the distance covered by factory remote starters, which are built into the BCM of the vehicle. The interface connects to the vehicle and uses the same codes as the factory remote to remote start the vehicle. The runtime and features are identical to the ones for the OEM remote starter. Some of the advantages of RXT are greater distance coverage and 2-way compatibility.

Range Extender Ready (RXT)

Command Engine Result

Start NOT running. The engine will be s tarted. Start Running. The engine will be stopped.

The following table describes the behavior of the vehicle in relation to the RXT feature. The following commands are performed on the aftermarket remote.

Runtime

Refer to vehicle owner's manual.

Runtime Reset

Refer to vehicle owner's manual.

RXT Operations

Button(s)

Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock .

Press & hold for 1 second to remote start.

Press & hold for 5 seconds to activate the trunk release (optional).

Press once, then to activate the rear hatch/tail glass release (optional).*

Press 3 times, then to activate the panic mode.

Press once, then to reset the remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more

information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Page 14

Quick Reference Guide

DBALL/DBALL2-CHRYSLER7 Range Extender Ready (RXT) Installation

SmartStart Compatible

This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.

What is SmartStart?

Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:

Ÿ Lock/Arm Ÿ Unlock/Disarm Ÿ Remote Car Starter Ÿ Trunk Release Ÿ Panic Ÿ Aux Channels

You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!

But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.

3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

For more information, visit www.mysmartstart.com.

Engine Idle Protection System (EIPS)

Vehicles equipped with RFID-type Push-to-Start ignition systems work by detecting a proximity key in the vehicle. They will run indefinitely if the key is removed, which could potentially lead users to exiting the vehicle while the engine is still running and the car is left idling on its own in a garage or a confined space.

To mitigate risk, we have designed a feature that is now available on the DBALL. It will detect the presence of the RFID fob in the vehicle, through the CAN bus. If left idling for more than the pre-defined runtime (i.e. 1 to 5 minutes) without detecting the fob, DBALL will send a signal to the vehicle in order to shut off the engine.

EIPS (Engine Idle Protection System) will:

§ Notify the user about the idling engine by sounding the horn with a series of short

beeps.

§ Shut down the engine after a pre-defined period of time (i.e. 1 to 5 minutes).

EIPS is configured using XpressVIP. The following window is displayed whenever a DBALL module is flashed.

§ If the engine fails to shut down due to some malfunction, EIPS will go into alarm

mode and will notify the user by all means possible (e.g. horn or siren).

Page 15

Quick Reference Guide

DBALL/DBALL2-CHRYSLER7 Range Extender Ready (RXT) Installation

Notes

Activating/deactivating EIPS:

§ To activate EIPS, remove all keys from the vehicle and close all doors while the

engine is running.

§ To deactivate EIPS, do one of the following actions:

Ÿ Open one of the doors. Ÿ Remote start the vehicle. Ÿ Turn the engine off. Ÿ Drive the vehicle.*

* The EIPS feature is disabled if the vehicle is in motion so there is no risk that the

vehicle will shut off while driving, regardless of the fob being present in the vehicle or not.