Directed DBALL-GM10 XPRESSKIT Quick Reference Manual

Page 1
Platform: DBALL Firmware: GM10 v. 2.08+
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Installation Guide
Data override and door lock interface compatible with new generation GM vehicles with a BLADE-type key (i.e. Camaro, Equinox and Lacrosse). The available features include: Transponder override (no key required); door lock control; factory security control; trunk release; door, hood and trunk sensing; tach sensing; and much more.
Refer to Quick Reference Guide (QRG) at the end of this guide for more information on how to use the various features offered with this product.
Important:
This guide is compatible with the GM10 firmware version 2.08 and higher.
Rev.: 20130304
Index
Vehicle Application Guide................................................................................................................................................
Installation
Type 1..............................................................................................................................................................................
Vehicle Wiring Reference Chart - Type 1 (pages 4-6).....................................................................................................
Type 2..............................................................................................................................................................................
Vehicle Wiring Reference Chart - Type 2.........................................................................................................................
Installation with T-Harness...............................................................................................................................................
Programming
Module Programming.................................
Feature & Option List.......................................................................................................................................................
Feature Programming...................................................................................................................................................... 13
LED Diagnostics & Troubleshooting................................................................................................................................ 14
Limited One-Year Consumer Warranty............................................................................................................................ 15
..................................................................................................................... 10
02
03 04 07 08 09
11 12
† Buick, Chevrolet and GMC are registered trademarks and property of .their respective companies.
© 2012 Directed. All rights reserved.
Page 2
Platform: DBALL Firmware: GM10 v. 2.08+
Rev.: 20130304
Page 2
Vehicle Application Guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
Vehicle s
2013
2012
2011
2010
CC-Heated Seats Activation
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
FOB-Control of aftermarket alarm with OEM remote
PK-Immobilizer Bypass-Data No Key Req'd
RS-Ignition Activation
RS-RAP Shut Down (Retained ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-Hand Brake Status
Buick
Encore 1 D D
LaCrosse 1 D D
LaCrosse 1 1 1 D D D
Regal 1 D D
Regal 1 1 D D D
Verano 1 1 D D
Chevrole t
Camaro 1 D D
Camaro 1 D D D
Camaro 1 1 D D D
Cruze 1 D D
Cruze 1 D D D
Cruze 1 D D D
Equinox 1 1 D D D
Equinox 1 1 D D D
Malibu 1 D D
Orlando 2 D D
Orlando 2 D D D
Sonic 2 2 D D
Spark 1 D D
Trax 1 D D
GMC
Terrain 1 1 1 1 D D D
ST-Ignition Status
Lege nd:
D: Data-to-Data (D2D) only CC: Comfort & Convenience Controls RS: Remote S tart & Engine Controls
•: D2D and W2W DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring
FOB: Sync CAN Interface w/ FOB Remote ST: Function/Feature Status
PK: Transponder & Immobilizer Override
© 2012 Directed. All rights reserved.
Page 3
Platform: DBALL Firmware: GM10 v. 2.08+
Installation Type 1
(-) Hood Status Input
(-) Trunk Status Input
(-) Door Status Input
(-) Handbrake Status Input*
(-) Ground
(+) Brake Input
(AC) Tach Input*
(-) Ground
(+) 12v(+) 12v
(-) Parking Lights
Rev.: 20130304
Page 3
Remote
Starter
(-) Lock Output
(-) Unlock Output
(-)Trunk Output
(-) Aux3***
(+) Starter Output
(+) Ignition Output
(-) GWR (Status)
White
(-) Driver
Door Sense
Trigger**
Pin 22
Cut
Lt. Blue
Pin 1
1 8
Pin 14
BA C
Pin 2
Lt. Green
Pin 6
169
1: Light Green: Single Wire CAN
10: Orange/Red: Relay 2 NC
11: Yellow/Red: Relay 2 Com
12: Brown/Red: Relay 2 NO
(+) 12v
1: Black/White: (-) Handbrake Status Output*
3: Green/White: (-) Door Status Output
Yellow
(On the Camaro and Cruze vehicles)
2: Green/Black: RAP OFF**
4: Red/Black: (-) Trunk Status Output
5: Violet/White: (AC) Tach Output*
7: Gray/Black: (+) Accessory Output
10: Yellow/Black: Data Bypass
11: Orange/Black: Data Bypass
12: Blue/Red: (-) Hood Status Output
Pin 5
Pin 6
OBDII
Diagnostic Connector
3:Tan/Black: HSCAN High
4:Tan: HSCAN Low
13: Red: (+) 12v
14: Black: (-) Ground(-) Ground
6: Gray: (+) Brake Output
8: Purple/Green: MUX 9: Purple/Brown: MUX
Clutch Switch
(black connector)
For manual
transmission
vehicles only.
14 12 2
RF
Programming button
LED
BCM (under driver-side of dash)
Refer to pages 4-6 for information on the BCM connections for each vehicle.
10: Blue/White: (-) GWR (Status) Input
8: Violet: (+) Starter Input
10
6: White/Black: (-) Heated Seats
3: Red/White: (-) Trunk Input 2: Blue: (-) Unlock Input 1: Green: (-) Lock Input
(+)12v
4
RX
DBALL
(-) Ground
TX
XKD2D65
Not required in D2D mode.
* These wires are optional connections required on some remote starters, which do not support the signals in D2D. ** If the RAP OFF wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
(Green/Black, pin 2/12) to the driver door sense trigger to avoid the issue.
*** Use (-) Aux or any (-) trigger to activate the heated seats function during run time.
† Heated seat feature must be enable, see Feature Programming (page 12).
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
© 2012 Directed. All rights reserved.
Page 4
Platform: DBALL Firmware: GM10 v. 2.08+
Vehicle Wiring Reference Charts - Type 1
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Buick LaCrosse
Description
Ignition Pink or Blue 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Brown or Violet 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Lt Blue or Lt. Green 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Lt Blue or Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 6 Black 7 Driver Window Switch, in driver's door SW CAN Dk Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
Buick Encore
Description
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Green/V iolet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 6 Black 7 Driver Window Motor, in driver's door SW CAN Dk Green 1 Blac k 16 OBDII CAN High Blue 6 Black 16 OBDII CAN Low White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
ConnectorWire
Rev.: 20130304
Page 4
Buick Regal
Description
Ignition Violet/Yellow or Violet/Black 6 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Brown/Yellow or Violet/Yellow 5 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Lt. or Dk. Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Lt. Blue or Dk. Green/Violet 2 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 6 Black 7 Driver Window Switch, in driver's door SW CAN Dk. Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
Buick Verano
Description
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Green/V iolet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 6 Black 7 Driver Window Motor, in driver's door SW CAN Dk Green 1 Blac k 16 OBDII CAN High Blue 6 Black 16 OBDII CAN Low White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
© 2012 Directed. All rights reserved.
Page 5
Platform: DBALL Firmware: GM10 v. 2.08+
Vehicle Wiring Reference Charts - Type 1
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Chevrolet Camaro
Description
Ignition Pink 6 Lt. Green 25 BCM, under driver-side dash, above accelerator pedal Accessory Brown 5 Lt. Green 25 BCM, under driver-side dash, above accelerator pedal Parking Lights Lt. Blue 22 White 26 BCM, under driver-side dash, above accelerator pedal Data Lt. Blue 2 Lt. Green 25 BCM, under driver-side dash, above accelerator pedal RAP OFF Gray/Black 6 Black 7 Driver Window Switch, in driver's door SW CAN Dk. Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
Chevrolet Cruze
Description
Ignition Violet/Black 6 Lt Green 25 BCM, under passenger-side of center dash Accessory Violet/Yellow 5 Lt Green 25 BCM, under passenger-side of center dash Parking Lights Dk Green/Gray 22 White 26 BCM, under passenger-side of center dash Data Dk Green/Violet 2 Lt Green 25 BCM, under passenger-side of center dash RAP OFF Gray 6 Black 8 Driver Window Switch, in driver's door* SW CAN Dk Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
* On vehicles with express up and down windows, the wire is at the driver window motor, black 7-pin plug, pin 6.
Color Pin Color No. Pins Location
ConnectorWire
ConnectorWire
Rev.: 20130304
Page 5
Chevrolet Equinox
Description
Ignition Pink 6 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Brown 5 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Lt. Blue 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Lt. Blue 2 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray/Black 6 Black 8 Driver Window Switch, in driver's door SW CAN Dk. Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
Chevrolet Malibu
Description
Ignition Violet 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 6 Black 8 or 7 Driver Window Switch or Motor, in driver's door SW CAN Dk Green 1 Black 16 OBDII CAN High Blue 6 Black 16 OBDII CAN Low White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorW ire
© 2012 Directed. All rights reserved.
Page 6
Platform: DBALL Firmware: GM10 v. 2.08+
Vehicle Wiring Reference Charts - Type 1
Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it.
Chevrolet Spark
Description
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Green/V iolet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 22 Pink 27 BCM, under driver-side dash, above driver-kick panel SW CAN Dk Green 1 Blac k 16 OBDII CAN High Blue 6 Black 16 OBDII CAN Low White 14 Black 16 OBDII
Color Pin Color No. Pins Location
Chevrolet Trax
Description
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray 6 Black 7 Driver W indow Motor, in driver's door SW CAN Dk Green 1 Black 16 OBDII CAN High Blue 6 Black 16 OBDII CAN Low White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
ConnectorWire
Rev.: 20130304
Page 6
GMC Terrain
Description
Ignition Pink 6 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel Accessory Brown 5 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel Parking Lights Lt. Blue 22 White 26 BCM, under driver-side dash, above driver-kick panel Data Lt. Blue 2 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel RAP OFF Gray/Black 6 Black 8 Driver Window Switch, in driver's door SW CAN Dk. Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
© 2012 Directed. All rights reserved.
Page 7
Platform: DBALL Firmware: GM10 v. 2.08+
Installation Type 2
Light Switch
Connector
(-) Parking Lights
Refer to the Vehicle Wiring Reference Chart (page 8) for wire color
654321
and location.
121110987
OBDII
Diagnostic Connector
Pin 1
Pin 6
1 8
169
Pin 14
(-) Driver Door Sense Trigger (Gray/Black)**
Data Bypass, Pin 2
Cut
(-) Hood Status Input
(-) Trunk Status Input
(-) Neutral Safety Input/(-) Handbrake Status Input*
(-) Ground
1: Light Green: Single Wire CAN
3:Tan/Black: HSCAN High
4:Tan: HSCAN Low
10: Orange/Red: Relay 2 NC
11: Yellow/Red: Relay 2 Com
12: Brown/Red: Relay 2 NO
(+) 12v
1: Black/White: (-) Handbrake Status Output*
3: Green/White: (-) Door Status Output
4: Red/Black: (-) Trunk Status Output
5: Violet/White: (AC) Tach Output*
7: Gray/Black: (+) Accessory Output
12: Blue/Red: (-) Hood Status Output
14: Black: (-) Ground(-) Ground
2: Green/Black: RAP OFF**
6: Gray: (+) Brake Output
10: Yellow/Black: Data Bypass
11: Orange/Black: Data Bypass
Accessory, Pin 3
(-) Door Status Input
(+) 12 V
(-) Parking Lights
13: Red: (+) 12v
(+) Brake Input
(AC) Tach Input*
(-) Ground
(+) 12 V
14 12 2
RF
Programming button
LED
Rev.: 20130304
Page 7
Remote
Starter
(-) Lock Output (-) Unlock Output (-)Trunk Output (-) Aux3*** (+) Starter Output
(+) Ignition Output
(-) GWR (Status)
10: Blue/White: (-) GWR (Status) Input
DBALL
8: Violet: (+) Starter Input
10
6: White/Black: (-) Heated Seats
3: Red/White: (-) Trunk Input 2: Blue: (-) Unlock Input 1: Green: (-) Lock Input
(+)12v
4
RX (-) Ground
TX
XKD2D65
321
Immobilizer Control
Module (K89)
Ignition Control
Not required in D2D mode.
* Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
** If the RAP OFF wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue.
*** Use (-) Aux or any (-) trigger to activate the heated seats function during run time.
† Heated seat feature must be enable, see Feature Programming (page 12).
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
Switch
Ignition, Pin 1
Refer to the Vehicle Wiring Reference Chart (page 8) for wire color and location.
654321
© 2012 Directed. All rights reserved.
Page 8
Platform: DBALL Firmware: GM10 v. 2.08+
Vehicle Wiring Reference Chart - Type 2
Chevrolet Orlando
Description
Ignition Violet/Black 1 Black 6 Ignition Control Switch Accessory Violet/Yellow 3 Black 6 Ignition Control Switch Parking Lights Green/Gray 3 Black 12 Light Switch Connector Data Green/Black 2 Violet 3 Immobilizer Control Module RAP OFF Gray 6 Black 7 Driver Window Motor SW CAN Dk. Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
Chevrolet Sonic
Description
Ignition Violet/Black 1 White 6 Ignition Control Switch Accessory Violet/Yellow 3 White 6 Ignition Control Switch Parking Lights Green/Gray 3 Black 12 Light Switch Connector Data Green/Violet 2 Violet 3 Immobilizer Control Module RAP OFF Gray 22 Pink 27 BCM Under Driver Dash (Express Down Windows) RAP OFF Gray 6 Black 7 Driver Window Motor (Express Up/Down Windows) SW CAN Dk Green 1 Black 16 OBDII CAN High Tan/Black or Blue 6 Black 16 OBDII CAN Low Tan or White 14 Black 16 OBDII
Color Pin Color No. Pins Location
ConnectorWire
ConnectorWire
Rev.: 20130304
Page 8
Locating Components in the Vehicle
Ignition Barrel
Immobilizer Control
Module ( )K89
Ignition Control
Switch
© 2012 Directed. All rights reserved.
Page 9
Platform: DBALL Firmware: GM10 v. 2.08+
Installation with T-Harness (for all GM10 vehicles)
Use connectors labeled GM10
(-) Ground
(-) Hood Status Input
(-) Ground
(+) 12v(+) 12v
Rev.: 20130304
Page 9
Light Switch
Connector
Remote
Starter
6
12
(-) Parking Lights
Refer to the Vehicle Wiring Reference Chart (pages 4, 5, 6, and 8) for
1
wire color and location.
7
Ignition Barrel
to vehicle 6-pin connector
To Theft Deterrent Module (TDM)
(under ignition switch, black connector)
GM10
Ignition
Connector
T-01
(-) Driver
Door Sense
Trigger*
(+) Ignition Output
3
GM10
1
Pink: Ignition Output.
Black/White: NC
2: Green/Black: (-) RAP OFF *
8: Purple/Brown: N.C.
9: Purple/Green: N.C.
Theft Deterrent Module (TDM) connector
Vehicle side
(-) Parking Lights
14 12 2
RF
Programming button
LED
DBALL
White/Black: N.C.
Remote Start Safety
Override Switch
10
(+) 12v
RX
4
(-) Ground
TX
NOT USED
T-02
Yellow
(On the Camaro and Cruze vehicles)
Clutch Switch
(black connector)
BA C
* If the RAP OFF wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
For manual
transmission
vehicles only.
T-Harness
THGM610
(Optional)
Cut away the 4-pin
connector and connect
the three wires to the
OBDII 16-pin connector.
NOT USED
SW CAN Lt. Green: pin 1
Can LOW
Tan or White: pin 14
© 2012 Directed. All rights reserved.
Can HIGH
Tan/Black or Blue: pin 6
1 8
169
Diagnostic connector
OBDII (connector side view)
Page 10
Platform: DBALL Firmware: GM10 v. 2.08+
Rev.: 20130304
Module Programming
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Warning!
available functions and features.
1. Connect the interface module to your computer using the XKLoader2.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.xpresskit.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top left corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select one of the available install options (config for RSR, RXT or Standard install), and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed: “The flashing is successfully completed. You may now unplug the kit.” You can now proceed with the programming instructions below.
To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
Page 10
1
2
3
4
5
D2D Installation
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
th
4
st
1
OR
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
The LED turns ON solid red.
Make sure the driver’s door is open.
Press the Unlock button on the OEM remote and wait until the LED starts to flash orange.
Steps 5 to 7 must be executed within 5 seconds.
Turn the key to the IGN position. The LED will start to flash green.
Remove the key from the ignition barrel. The LED will keep flashing green.
st
1
n
i
D2D
p
-
10
2D
n
i
D
p
-
0
1
Press Unlock button
Key IN
Key OUT
n
i
p
-
4
n
1
2-pi
1
rd
3
nd
2
-pin
n
14
i
-p
12
rd
3
nd
2
Solid
&
Flashes
OFF
GN
I
&
START
OFF
N
G
I
START
Flashes
&
Flashes
Insert and turn the key back to the IGN position. The LED will
6
7
change to solid green for 3 sec. then OFF.
Remove the key from the ignition.
OFF
Key IN
Key OUT
N
G
I
START
OFF
© 2012 Directed. All rights reserved.
&
Solid
IGN
START
Page 11
Platform: DBALL Firmware: GM10 v. 2.08+
Rev.: 20130304
Page 11
Module Reset
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
D2D Installation
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
in
D2D
p
-
10
th
5
st
1
rd
3
2
pin
-
n
14
i
2-p
1
nd
th
4
OR
1
2
Hard Reset
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
W2W Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
D2D Installation
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the
th
5
programming button, then connect the 4-pin D2D harness.
-pin
n
2D
in
D
p
-
10
st
1
th
4
14
pi
-
12
nd
2
rd
3
& &
rd
3
Release
nd
2
th
4
-pin
4
n
1
i
2-p
1
Solid Solid
n
D2D
pi
10-
st
1
1
2
3
OR
W2W Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
D
n
D2
pi
-
0
1
st
1
th
4
nd
2
rd
3
Solid
Release
pin
-
14
in
12-p
&
Flashes
&
Solid
© 2012 Directed. All rights reserved.
Page 12
Fea t. Opera tion Flashes/Option Description
Platform: DBALL Firmware: GM10 v. 2.08+
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.xpresskit.com. The web offers more options such as EIPS and RSR; however, a manual configuration of the features is possible using the information on this page.
1. No RF Output* Module is connected to a remote starter using a standard installation.
RFTD Output Type1
Unlock Driver Priority2
Automatic Comfort
3
Closure with Lock
4 Heated Seats
5 Heated Seats Control
Automatic Controlled
6
Door Lock
Smart OEM Alarm
7
Control
* Defaul t Option ** Do not use in vehicles without sunroof
2. RFTD Output Module is c onnected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartSt art using an RSR or RXT installation (when available).
1. Driver priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
2. All Unlocks all doors on first press.
1. Disabled* N/A
2. Windows Only N/A
3. Windows and sunroof ** N/A
1. Disabled* No operation.
2. Enabled It will activate the Heated Seats Control feature (see feature #5).
1. 32 °F (0 °C)*
2. 23 °F (-5 °C)
3. 41 °F (5 °C)
4. Always ON When feature #4 is enabled, it will activate the heated seats at any temperature.
1. Disabled* No operation.
2. Ignition Locks all doors when ignition is ON. Unlocks all doors when ignition turns OFF.
3. Brake
4. Speed Locks all doors when the vehicle is moving. Unlocks all doors when ignition turns OFF.
1. Disabled
2. Safelock
3. Enable d*
When feature #4 is enabled, it will activate the heated seats upon remote start when temperature is below 32 °F (0 °C).
When feature #4 is enabled, it will activate the heated seats upon remote start when temperature is below 23 °F (-5 °C).
When feature #4 is enabled, it will activate the heated seats upon remote start when temperature is below 41 °F (5 °C).
Locks all doors when brake pedal is pressed while the vehicle is running. Unlocks all doors when ignition turns OFF.
The OEM alarm will not be c ontrolled by DBALL upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown.
Smart OEM Alarm Control will sy nchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm c ontrol must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock s tatus to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is act ive, will work perfectly with this option and will make it invisible to the user.
Rev.: 20130304
Page 12
© 2012 Directed. All rights reserved.
Page 13
Platform: DBALL Firmware: GM10 v. 2.08+
Feature Programming
To enter feature programming routine
-
Turn the ignition ON, then OFF.
-
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the Programming button.
-
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options
-
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
-
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green
slowly the number of times to indicate the current feature.
Accessing another feature
-
Press and release the programming button a number of times to advance from the current feature to the next desired .
-
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature.
The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
-
Other features can be programmed.
-
The feature programming can be exited.
The flashing sequence will repeat until a new command is entered.
Programming
Button
Rev.: 20130304
Page 13
feature
Exiting feature programming
-
No activity for 30 seconds; after 30 seconds, the LED will turn ON for 2 seconds to confirm the end of the programming orange sequence. OR
-
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON for 2 seconds to confirm end of the programming sequence
.
orange the
© 2012 Directed. All rights reserved.
Page 14
LED Status Description Troubleshooting
Module Programming
Platform: DBALL Firmware: GM10 v. 2.08+
LED Diagnostics and Troubleshooting
Rev.: 20130304
Page 14
Solid
Flashes
Flashes
Solid x3 sec.
Flashes x1
Solid Red Waiting for Can detection.
Flashes Orange
CAN and Data Bypass successfully detected.
Flashes Green Cycle timeout started.
Solid Green 3 seconds
Flashes Red 1 time
Module successfully programmed.
Data Bypass line sleeping or not connected.
Make sure that your HSCAN and SWCAN are properly connected and press Unlock on the OEM remote.
Normal operation
Normal operation. You have now 5 seconds to finish module programming.
Normal operation
Press Unlock on the OEM remote to activate the Data Bypass.
Failed to completely remove the
Flashes x2
Flashes Red 2 times
key from ignition or turned the ignition OFF without removing the key while bypass sequence was
Cycle (programming steps 5 to 7) was done without removing the key. Reset module and retry module programming from step 1.
executing.
Flashes x3
Flashes Red 3 times
Cycle (programming steps 5 to 7) timed out.
Cycle (programming steps 5 to 7) was done slower than 5 seconds. Reset module and retry module programming from step 1.
Make sure that your connections to Data Bypass are correct,
Flashes x4
Flashes Red 4 times
Data Bypass line sleeping or not connected.
remove key, press Unlock on the OEM remote and make s ure that the LED is flashing orange before turning the key to ignition.
Flashes x5
Flashes x6
Flashes x7
Flashes Red 5 times Programming failed.
Flashes Red 6 times HS CAN not detected.
Flashes Red 7 times SW CAN not detected.
Active Ground W hile Running
Flashes
Off
Flashes Green Ground out (GWR) is active. Normal operation
Off Normal operation
Inactive Ground While Running
Flashes x1
Flashes x2
Flashes x3
Flashes Green once Lock function executed.
Flashes Green twice Unlock function executed.
Flashes Green 3 times Trunk release function executed.
Reset the module and retry the module programming from step
1.
Check connections and click Unlock again to activate the line.
The Ground While Running (status) wire is incorrectly connected. Refer to the wiring diagram to make the right connections.
If it does not flash, the bypass module did not receive the signal.
Verify the connections between the bypass and the remote
starter module.
© 2012 Directed. All rights reserved.
Page 15
Platform: DBALL Firmware: GM10 v. 2.08+
Rev.: 20130304
Page 15
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
920-0007 2009-09
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Additional information can be found at:
www.xpresskit.com www.directechs.com
© 2012 Directed. All rights reserved.
Page 16
Rev.: 20130304
Quick Reference Guide
DBALL-GM10
© 2012 Directed. All rights reserved.
Button(s)
Actions
Press & hold for 1 second to loc k.
Press & hold for 1 second to unlock .
Press & hold for 1 second to remote start.
Press & hold for 5 seconds to activate the trunk release (optional).
Press once, then to activate the rear hatch/tail glass release (optional).*
Press 3 times, then to activate the panic mode.
Press once, then to reset the remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more
information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Additional Features
(Must be completed by the installer.)
Note: Additional fees may apply for the installation of the above features.
Trunk
The following features are available with this product, but may not be compatible with your vehicle. Refer to your installation facility for more information.
Heated Seats Feature
Heated Seats will start automatically at _________________ level if the ambiant temperature is below _________°F (_________°C).
Even if Heated Seats Temperature Control is set to start below a specific temperature, you can remote activate heated seats manually with your aftermarket remote by pressing AUX3 button(s). Available only if your vehicle is running by remote starter.
Notes
Loading...