Directed DBALL2-TL7 Installation Manual

Page 1

Platform: DBALL2 Firmware TL7:

Update Alert: Firmware updates are posted the web on a regular basis. We recommendon that you check for firmware and/or install guide updates prior to installing this product.

Installation Guide

The TL7 firmware for 2 is an all-in-one door lock and override module compatible with specificDBALL Scion and Toyota vehicles.

This module can only be flashed and configured using Xpress at www.directechs.com orVIP using the Directechs Mobile application for smartphones. Refer to

section on page 22

Index

for more information.

Rev.: 20 914170

the Module Programming

Vehicle Application Guide ....... .................. .................................. ............................... ....................................................

Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)

Type 1........................................ ....................................................................................................................................

Type 2............................................................................................................................................................................

Type 3............................................................................................................................................................................

Type ............................................................................................................................................................................4

Type ........................................ ...........................................................................................................5 .........................

T6ype ...........................................................................................................................................................................

T7ype ...........................................................................................................................................................................

T8ype ...........................................................................................................................................................................

Type 9............................................................................................................................................................................

Programming

Module Programming.............. .......................................................................................................... ............................

Module Reset ard Reset....................................................................................................& H ......................................

Features & Option List. .................................................................................................................... ..............................

Features ....................................................................................................................Programming.. ............................

LED Diagnostics ................................................................................................................... ..& Troubleshooting. .......

Limited One-Year Consumer Warranty..........................................................................................................................

Quick Reference Guide............................................................................................. ....................................................

03 06 08 10 12 14 16 18 20

22 23 24 25

® Toyota Scion are registered trademarks and property of .and their respective companies

Page 2

Platform: DBALL2

Vehicles

2017

2016

2015

2014

2013

2012

2011

2010

PK-Immobilizer Bypass-Data No Key Req'd

AV-P arking Lights Control

DL-Arm Factory Securit y

DL-Disarm Fact ory Sec urit y

DL-Door Lock Control

DL-Door Unlock

DL-Driver P riority Unloc k

DL-Sliding Door Control Driv er

DL-Sliding Door Control Pass enger

DL-Trunk / Hatc h Release

FOB-Control of aft ermarket alarm with OEM remote

RS-Tach / RPM Output

SS-E ntry Monit oring A LL Door Pins

SS-E ntry Monit oring Hood Pin

SS-E ntry Monit oring Trunk/Hatch Pin

SS-Factory A larm Trigger Monitoring

ST-Brake S tat us (foot brake)

ST-Door Loc ks Status

ST-E -Brak e Stat us

ST-Ignition St atus

Scion

iQ 1111

••••••• •• •D•D••

tC 111111

••••••• • ••••D•D••

xB 22222

••••••• D••••D•D••

xD 5555

••••••• D•• •D•D••

Toyota

4Runner (G K ey) 11111111

••••••• • ••••D•D••

Camry(GKey) 88811

••••••• •D••••D•D••

Corolla (G K ey) 2 2

••••••• •D••••D•D••

Highlander (G Key) 6 6 6

••••••• D••••D•D••

Highlander Hy brid (G Key) 6 6

••••••• D••••D•D••

Matrix(GKey) 222

••••••• D••••D•D••

Priusc 111

••••••• •• •D•D••

RAV4 (G Key) 2 2

••••••• D•• •D•D••

Sequoia (G Key ) 3333

••••••• D••••D•D••

Sienna (G Key ) 7777

••••••••••D••••D•D••

Tacoma(GKey) 44444

•

Tundra (G Key ) 9999999

••••••• D••••D•D••

Venza(GKey) 1111111

••••••• • ••••D•D••

Yaris(GKey) 1115

••••••• •• •D•D••

Legend:

D: Data-to-Data (D2D) only

AV: Horn & Lights Controls

•: D2D & W ire-t o-W ire (W2W )

DL: OE Door Loc k & A larm Controls

FOB: Sy nc CAN Interface w/FOB Remote

PK: Transponder & Immobilizer Override

RS: Remote Start & Engine Controls

SS: Integrated Sec urity & Monitoring

ST: Function/Feature S tat us

* Version 1.27+ : The m otoriz ed trunk feature needs to be enabled during the firmware flashing process .

Firmware TL7:

Rev.: 20 914170

Page 2

Vehicle Application Guide

The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.

It is important to make sure you do connect the keysense wire in the installation for each of these vehicles orNOT you will encounter issues when attempting to start the vehicle.

Key Type

Some Toyota 2010+ models have

different encryption types. Please look at your key blade and identify the markings. A “G” means the vehicle is compatible with the 7TL firmware.

G-stamped keys Standard Key

For vehicles with key , seedot-stamped s the

1TL firmware.

H-stamped keys

For vehicles with key , seedot-stamped s the

10TL firmware.

Page 3

Platform: DBALL2 Firmware TL7:

Installation Type 1

Rev.: 20 914170

Page 3

It is important to make sure you do connect the keysense wire in th installation or youNOT is will encounter issues when attempting to start the vehicle.

[2]

[3] in 18(-) Parking Lights: P

[4] : PAutolights in 19

Make this connection only if the vehicle is equipped with Automatic Headlamps.

Headlight Switch

(-) Hood Status Input

(+) Brake InputStatus

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

connector OBDII

Output(-) Parking Lights

Diagnostic

Remote

Starter

SIL in 7: P

HS CAN : PHigh in 6

HS CAN : PLow in 14

(+) 12V Input (+) Starter Output2 (+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Ground

(-) OutputLock

(-) OutputUnlock

(-) Trunk Output

(-) GWR Output

169

Ignition onnectorC

4321 8765

Fuse Box Connector

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

Prog utton. B

LED

DBALL/

DBALL2

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

3: (-) Trunk InputRed/White:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

CUT

Body ECU Connector

Note: RDA wire is NOT

required in all vehicles.

Refer to vehicle Wiring and

Connector References

Information for wire and

connector details.

[4] Autolights Interr. (veh. side): 10Orange/Red:

[4] Autolights Interr. (conn. side): 11Yellow/Red:

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]2

(-) Hood Status Output: 12Blue/Red:

RDA

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

RDA: 11Orange/Black:

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data. [4] Autolights Interrupt only required if vehicles are equipped with Autolights.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 4

Platform: DBALL2

Function Color Pin Pola rity Location Color Pins

Scion iQ 2012-2015

HS CAN High Violet 6 Data OBDII connector. Black 16 HS CAN Low White 14 Data OBDII connector. Black 16 SIL Red 7 Data OBDII c onnector. Black 16 RDA Brown 26 Data Body ECU. Gray 30 Parking Lights Yellow 18 (-) Headlight Switch. White 20 Autolights Gray 19 Cut Headlight Switch. White 20 Ignition 1 Brown 6 (+) Ignition Switch. White 8 Ignitiion 2 Lt. Blue 4 (+) Ignition Switch. White 8 Starter 1 Red 8 (+) Ignition Switch. White 8 Starter 2 Lt. Green 1 (+) Ignition Switc h. White 8 12V Blue 7 (+) Ignition Switch. White 8

Scion tC 2011-2016

HS CAN High Lt.Green 6 Data OBDII Connector. White 16 HS CAN Low White 14 Data OBDII Connector. White 16 SIL Violet 7 Data OBDII Connector. White 16 RDA Lt. Green 26 Data Body ECU. White 30 Parking Lights Violet 18 (-) Headlight Switch. White 20 Autolights Ignition 1 Gray 6 (+) Ignition Switch. White 8 Ignition 2 Gray 4 (+) Ignition Switch. White 8 Starter 1 Green 8 (+) Ignition Switch. White 8 Starter 2 Tan 1 (+) Ignition Switch. White 8 12V White 7 (+) Ignition Switch. White 8

Toyota 4Runner (G Key) 2010-2017

HS CAN High Violet 6 Data OBDII Connector. White 16 HS CAN Low White 14 Data OBDII Connector White 16 SIL Green 7 Data OBDII Connector White 16 RDA Pink 26 Data Body ECU. White 30 Parking Lights Red 18 (-) Headlight Switch. White 20 Autolights White 19 Cut Headlight Switch. White 20 Ignition 1 Black 6 (+) Ignition Switch. White 8 Ignitiion 2 Violet 4 (+) Ignition Switch. White 8 Starter 1 Red 8 (+) Ignition Switch. White 8 Starter 2 Black 1 (+) Ignition Switch. White 8 12V Green 7 (+) Ignition Switch. White 8

Toyota Camry (G Key) 2010-2011

HS CAN High Black 6 Data OBDII. Black 16 HS CAN Low White 14 Data OBDII. Black 16 SIL Gray 7 Data OBDII. Black 16 RDA Blue 12 Data Body ECU, driver dash fusebox. White 28 Parking Lights Black 18 (-) Headlight switch. White 20 Autolights Green 19 Cut Headlight switch White 20 12V Black 5 (+) Ignition switch. White 8 Accessory White 2 (+) Ignition switch. White 8 Ignition 1 Yellow 6 (+) Ignition switc h. White 8 Ignition 2 Pink 1 (+) Ignition switch. White 8 Starter 1 Blue 7 (+) Ignition switc h. White 8 Starter 2 Gray 3 (+) Ignition Switch. White 8

Wire Informa tion

Connector Information

Not equipped.

Firmware TL7:

Rev.: 20 914170

Type 1 - Vehicle Wiring Reference Chart

Page 4

Page 5

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Prius C (G Key) 2012-2014

HS CAN High Gray 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL Black 7 Data OBDII Connector. Black 16 RDA Lt. Green 16 Data Body ECU. Gray 30 Parking Lights Lt. Blue 18 (-) Headlight Switc h. W hite 20 Autolights Red 19 Cut Headlight Switch. White 20 Ignition 1 Pink 6 (+) Ignition Switc h. White 8 Ignition 2 Lt. Blue 1 (+) Ignition Switch. White 8 Starter 1 Green 7 (+) Ignition Switch. White 8 Starter 2 12V Black 1 (+) Dash Fuse Box. White 1

Toyota Venza (G Key) 2010-2016

HS CAN High Yellow 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector Black 16 SIL Blue 7 Data OBDII Connector Black 16 RDA Lt. Green 12 Data Body ECU. White 28 Parking Lights Red 18 (-) Headlight Switch. W hite 20 Autolights Brown 19 Cut Headlight Switch. White 20 Ignition 1 Green 6 (+) Ignition Switch. White 8 Ignition 2 Red 4 (+) Ignition Switch. White 8 Starter 1 Red 8 (+) Ignition Switch. White 8 Starter 2 Green 1 (+) Ignition Switch. White 8 12V Blue 7 (+) Ignition Switc h. White 8

Toyota Yaris (G Key) 2012-2014

HS CAN High Gray 6 Data OBDII Connector. White 16 HS CAN Low White 14 Data OBDII Connector W hite 16 SIL Black 7 Data OBDII Connector W hite 16 RDA Pink 26 Data Body ECU. White 30 Parking Lights Lt. Blue 18 (-) Headlight Switc h. W hite 20 Autolights Ignition 1 Pink 6 (+) Ignition Switc h. White 8 Ignitiion 2 Lt. Blue 1 (+) Ignition Switch. White 8 Starter 1 Green 7 (+) Ignition Switch. White 8 Starter 2 12V Black 1 (+) Dash Fusebox. White 1

Not equipped.

Wire Information Connector Information

Not equipped.

Firmware TL7:

Rev.: 20 914170

Page 5

Page 6

Platform: DBALL2 Firmware TL7:

Installation Type 2

It is important to make sure you do connect the keysense wire in th installation or youNOT is will encounter issues when attempting to start the vehicle.

[]2

(-) Hood Status Input

(+) Brake InputStatus

Make this

connection if theonly vehicle is equipped with Automatic Headlamps.

Autolights in 19: P

[4]

CUT

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

[3] in 18(-) Parking Lights: P

Output(-) Parking Lights

Headlight Switch

Starter

(+) 12V Input (+) Starter Output2

Remote

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Ground

(-) OutputLock

(-) OutputUnlock

(-) putTrunk In

(-) GWR Output

HS CAN : PHigh in 6

Ignition onnectorC

Fuse Box Connector

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

SIL in 7: P

169

Diagnostic

onnector OBDIIC

Rev.: 20 914170

4321 8765

Page 6

Not required in D2D mode.

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

Autolights Interr. (veh. side): 10Orange/Red:

[4]

Autolights Interr. (conn. side): 11Yellow/Red:

[4]

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

Prog utton. B

LED

HS CAN : PLow in 14

DBALL2

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

3 Trunk: (-) InputRed/White:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 7

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Scion xB 2011-2015

HS CAN High Lt. Green 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL White 7 Data OBDII Connector. Black 16 RDA Parking Lights White 18 (-) Headlight Switch. White 20 Autolights Ignition 1 Gray 6 (+) Ignition Switch. White 8 Ignition 2 White 4 (+) Ignition Switch. White 8 Starter 1 White 8 (+) Ignition Switch. W hite 8 Starter 2 White 1 (+) Ignition Switch. W hite 8 12V White 7 (+) Ignition Switch. White 8

Toyota Corolla (G Ke y) 2012-2013

HS CAN High Lt. Green 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL White 7 Data OBDII Connector. Black 16 RDA Parking Lights Brown or W hite 18 (-) Headlight Switch. W hite 20 Autolights Ignition 1 Brown or Gray 6 (+) Ignition Switch. White 8 Ignition 2 Green or W hite 4 (+) Ignition Switch. W hite 8 Starter 1 Black or White 8 (+) Ignition Switch. White 8 Starter 2 White (if equipped) 1 (+) Ignition Switch. W hite 8 12V White 1 (+) Dash Fusebox. W hite 1

Toyota Matrix (G Key) 2012-2014

HS CAN High Lt. Green 6 Data OBDII Connector. White 16 HS CAN Low White 14 Data OBDII Connector. W hite 16 SIL White 7 Data OBDII Connector. White 16 RDA Parking Lights Brown 18 (-) Headlight Switch. White 20 Autolights Gray 19 Cut Headlight Switch. W hite 20 Ignition 1 Brown 6 (+) Ignition Switch. White 8 Ignition 2 Green 4 (+) Ignition Switch. White 8 Starter 1 Black 8 (+) Ignition Switch. W hite 8 Starter 2 White (2.4L only) 1 (+) Ignition Switc h. W hite 8 12V Black 1 (+) Dash Fusebox. W hite 1

Toyota RAV4 (G key) 2011-2012

HS CAN High Black 6 Data OBDII Connector. W hite 16 HS CAN Low White 14 Data OBDII Connector. W hite 16 SIL White 7 Data OBDII Connector. White 16 RDA Parking Lights White 18 (-) Headlight Switch. White 20 Autolights Green 19 Cut Headlight Switch. White 20 Ignition 1 White 6 (+) Ignition Switch. White 8 Ignition 2 Pink 4 (+) Ignition Switch. White 8 Starter 1 Yellow 8 (+) Ignition Switch. White 8 Starter 2 White 1 (+) Ignition Switch. W hite 8 12V Blue 7 (+) Ignition Switc h. W hite 8

Not equipped

Wire Informa tion

Not equipped

Connector Information

Not equipped

Firmware TL7:

Type - Vehicle Wiring Reference Chart2

Rev.: 20 914170

Page 7

Page 8

Platform: DBALL2 Firmware TL7:

Installation Type 3

Rev.: 20 914170

Page 8

It is important to make sure you do connect the keysense wire in thNOT is installation or you will encounter issues when attempting to start the vehicle.

[]2

[3] (-) Parking Lights , p: in 18Tan

20 19

[4]

Make this connection

:, pAutolights in 19Green

only if the vehicle is equipped with Automatic Headlamps.

CUT

(-) Hood Status Input

(+) Brake InputStatus

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

Headlight Switch

SIL: , p 0in 1Blue

Starter

Output(-) Parking Lights

Tire Pressure Warning ECU

(Behind glove box)

654321

1211 10 987

(-) Ground

(+) 12V Input

Remote

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Trunk Release Output

(-) OutputLock (-) OutputUnlock

(-) GWR Output

CAN , pHigh: in 6Violet SIL:

Diagnostic

onnector OBDIIC

Ignition onnectorC

4321 8765

Fuse Box Connector

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

in 7Tan , p

169

CAN Low:

in 14White, p

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

CUT

SIL Interr. (conn. side) : 8Yellow:

SIL Interr. (veh. side) : 9Orange/Yellow:

Autolights Interr. (veh. side): 10Orange/Red:

[4]

Autolights Interr. (conn. side): 11Yellow/Red:

[4]

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

Prog utton.B

LED

DBALL2

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

(-) :Power Liftgate

Red, pin 6

Power Liftgate

WhiteSwitch

846 27351

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data.

[4] Autolights Interrupt only required if vehicles are equipped with Autolights.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 9

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Sequoia (G Key) 2011-2014

HS CAN High Violet 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL Tan 7 Data OBDII Connector. Black 16 SIL Interrupt Blue 10 Cut

TPMS Connector, behind the glove box. White 12 Parking Lights Tan 18 (-) Headlight Switch. White 20 Autolights Green 19 Cut Headlight Switch. White 20 Ignition 1 Black 6 (+) Ignition Switch. W hite 8 Ignition 2 Lt. Green 1 (+) Ignition Switch. W hite 8 Starter 1 Green 7 (+) Ignition Switch. White 8 12V Black 1 (+) Dash Fusebox. White 1 Power Lifgate Red 6 (-) Power Liftgate Switch. White 8

Wire Information Connector Information

Firmware TL7:

Type - Vehicle Wiring Reference Chart3

Rev.: 20 914170

Page 9

Page 10

Platform: DBALL2 Firmware TL7:

Installation Type 4

It is important to make sure you do connect the keysense wire in thNOT is installation or you will encounter issues when attempting to start the vehicle.

[]2

[3] (-) Parking Lights: , pin 18Lt.Green

Brake 4-pin

Blue Switch

(+) Brake: ,Lt. Blue

pin 1

Headlight Switch

(-) Hood Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3] (-) Parking Lights Output

(+) Brake InputStatus

[1] (AC) Tach Input

[1]

Tach in 9:, pBlack/White

SIL in 7:, pWhite

HS CAN :High

Starter

Diagnostic

in 6Yellow/Black, p

OBDII

169

HS CAN :Low Blue/White, pin 14

(+) 12V Input (+) Starter Output2

Remote

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Ground

(-) OutputLock (-) OutputUnlock

(-) GWR Output

onnectorC

Ignition onnectorC

Refer to the Vehicle Wiring

Reference Information for wire

4[]

[]4

Harness from Driver Side

()Gray or White Connector

, pinViolet 4

[]4 (-) Unlock/Disarm:

Green/Black, p 8in

1049271638

[]4 (-) Lock/Arm:

Rev.: 20 914170

4321 8765

and connector details.

Page 10

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

SIL: 10Yellow/Black:

Prog utton. B

LED

DBALL2

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

(+)12V

RX (-) Ground TX

P#: XKD2D65

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data. [4] Remote starter MUST be programmed during flashing to unlock before start and lock after start. This can be done when flashing the firmware under

the Data Feature Configuration section and enabling Safelock under Smart OEM Alarm Control. This Unlock output must also be programmed for double pulse.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 11

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Tacoma (G Ke y) 2011-2015

HS CAN High Yellow/Blac k 6 Data OBDII Connector. White 16 HS CAN Low Blue/White 14 Data OBDII Connector. Black 16 SIL White 7 Data OBDII Connector. White 16 Tach Blac k/W hite 9 Data OBDII Connector. White 16 Parking Lights Green 18 (-) Headlight Switch. White 20 Ignition 1 Black/Red 6 (+) Ignition Switch. White 8 Ignition 2 Blue/Yellow 1 (+) Ignition Switch. White 8 Starter 1 Green/Black 7 (+) Ignition Switch. W hite 8 Starter 2 Black/White 3 (+) Ignition Switch. W hite 8 12V White/Red 5 (+) Ignition Switch. W hite 8 Lock Violet 4 (-) Drivers Kick panel. White or Gray 10 Unlock (double pulse) Green/Black 8 (-) Drivers Kick panel. White or Gray 10 Brake Lt.Blue 1 (+) Brake Switch. Blue 4

Wire Information Connector Information

Firmware TL7:

Type - Vehicle Wiring Reference Chart4

Rev.: 20 914170

Page 11

Page 12

Platform: DBALL2 Firmware TL7:

Installation Type 5

Rev.: 20 914170

Page 12

It is important to make sure you do connect the keysense wire in th installation or youNOT is will encounter issues when attempting to start the vehicle.

[2]

(-) Hood Status Input

[3] in 13(-) Parking Lights: , pWhite

11 10 9 8 7

Headlight Switch

(+) Brake InputStatus

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

Output(-) Parking Lights

HS CAN : , pHigh in 6Violet

Diagnostic

connector OBDII

HS CAN : , pLow in 14White

Remote

Starter

SIL in 7:, pBlue

(+) 12V Input

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Ground

(-) OutputLock

(-) OutputUnlock

(-) Trunk Output

(-) GWR Output

169

Ignition onnectorC

4321 8765

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

Prog utton. B

LED

DBALL/

DBALL2

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

3: (-) Trunk InputRed/White:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 13

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Scion xD 2011-2014

HS CAN High Violet 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL Blue 7 Data OBDII Connector. Black 16 RDA Not equipped Parking Lights White 13 (-) Headlight Switch. White 13 Autolights Ignition 1 Pink 6 (+) Ignition Switch. W hite 8 Ignition 2 Green 1 (+) Ignition Switc h. W hite 8 Starter 1 Black 7 (+) Ignition Switch. W hite 8 Starter 2 12V Yellow 4 (+) Ignition Switch. W hite 8

Toyota Yaris (G Key) 2011

HS CAN High Violet 6 Data OBDII Connector. White 16 HS CAN Low White 14 Data OBDII Connector White 16 SIL Blue 7 Data OBDII Connector White 16 RDA Not equipped Parking Lights White 13 (-) Headlight Switch. White 13 Autolights Ignition 1 Pink 6 (+) Ignition Switch. W hite 8 Ignitiion 2 Green 1 (+) Ignition Switch. W hite 8 Starter 1 Black 7 (+) Ignition Switch. W hite 8 Starter 2 12V Yellow 4 (+) Ignition Switch. W hite 8

Wire Information Connector Information

Not equipped

Firmware TL7:

Type 5 - Vehicle Wiring Reference Chart

Rev.: 20 914170

Page 13

Page 14

Platform: DBALL2 Firmware TL7:

Installation Type 6

It is important to make sure you do connect the keysense wire in thNOT is installation or you will encounter issues when attempting to start the vehicle.

Rev.: 20 914170

Page 14

Ignition onnectorC

CUT

[3] (-) Parking Lights , p: in 18Lt. Blue

20 19

[4]

Autolights in 19:, pGreen

Make this connection only if the vehicle is equipped with Automatic Headlamps.

[4]

[]2

(-) Hood Status Input

(+) Brake InputStatus

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

Output(-) Parking Lights

Headlight Switch

HS CAN or , pHigh: in 6Blue Black

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

Autolights Interr. (veh. side): 10Orange/Red:

Autolights Interr. (conn. side): 11Yellow/Red:

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

(+) 12V Input

(+) Starter Output1

Remote

Starter

(+) Starter Output2

(+) Ignition Output2

(+) Ignition Input/Output1

(-) Trunk Release Output

(-) Ground

(-) OutputLock

(-) OutputUnlock

(-) GWR Output

SIL:

HS CAN Low:

Prog utton.B

LED

169

in 7Gray, p

Diagnostic

in 14White, p

DBALL2

4321 8765

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

(-) Power Liftgate:

Red, pin 4

onnector OBDIIC

534 21

Power Liftgate

WhiteSwitch

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data.

[4] Autolights Interrupt only required if vehicles are equipped with Autolights.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 15

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Highlander (G Key) 2011-2013

HS CAN High Blue 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL Gray 7 Data OBDII Connector. Black 16 RDA Parking Lights Lt. Blue 18 (-) Headlight Switch. W hite 20 Autolights Green 19 Cut Headlight Switch. W hite 20 Ignition 1 Black 6 (+) Ignition Switch. W hite 8 Ignition 2 Lt. Blue 1 (+) Ignition Switch. W hite 8 Starter 1 Yellow 7 (+) Ignition Switc h. White 8 Starter 2 Red or Blac k 3 (+) Ignition Switch. White 8 12V Red 5 (+) Ignition Switch. W hite 8 Power Liftgate Red 4 (-) Power Liftgate Switch. Black 5

Toyota Highlander Hybrid (G Ke y) 2012-2013

HS CAN High Black 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL Gray 7 Data OBDII Connector. Black 16 RDA Parking Lights Lt. Blue 18 (-) Headlight Switch. W hite 20 Autolights Green 19 Cut Headlight Switch. W hite 20 Ignition 1 Black 6 (+) Ignition Switch. W hite 8 Ignition 2 Lt. Blue 1 (+) Ignition Switch. W hite 8 Starter 1 Yellow 7 (+) Ignition Switc h. White 8 Starter 2 12V Green 5 (+) Ignition Switch. W hite 8 Power Liftgate Red 4 (-) Power Liftgate Switch. Black 5

Not equipped

Not equipped.

Not equipped

Wire Information Connector Information

Firmware TL7:

Type 6 - Vehicle Wiring Reference Chart

Rev.: 20 914170

Page 15

Page 16

Platform: DBALL2 Firmware TL7:

Installation Type 7

Rev.: 20 914170

Page 16

It is important to make sure you do connect the keysense wire in thNOT is installation or you will encounter issues when attempting to start the vehicle.

[]2

(-) Hood Status Input

[3] (-) Parking Lights , p: in 18Yellow

20 19

[4]

Autolights in:, p19Violet

Make this connection only if the vehicle is equipped with Automatic Headlamps.

CUT

(+) Brake InputStatus

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

Headlight Switch

SIL: , p 0in 1White

Starter

Output(-) Parking Lights

Tire Pressure Warning ECU

(Behind glove box)

654321

1211 10 987

(+) 12V Input

Remote

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Ground

(-) OutputLock (-) OutputUnlock

(-) Trunk Output Aux 1 Right Slide Output Aux 2 Left Slide Output

(-) GWR Output

[]4

CAN , pHigh: in 6Red SIL:

[]4

CAN Low:

Ignition onnectorC

4321 8765

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

in 7White, p

Diagnostic

onnectorC

169

OBDII

in 14White, p

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

CUT

RDA: ,Pink

pin 26

SIL Interr. (conn. side) : 8Yellow:

SIL Interr. (veh. side) : 9Orange/Yellow:

Autolights Interr. (veh. side): 10Orange/Red:

[4]

Autolights Interr. (conn. side): 11Yellow/Red:

[4]

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

RDA: 11Orange/Black:

Body ECU Connector

(middle plug)

456

161718

131415

282930

101112

252627

222324

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

5 Aux 2 Left Slide Input: Violet/Black:

Prog utton.B

LED

123

789

192021

DBALL2

4 Aux 1 Right Slide Input: White/Violet:

3: (-) Trunk InputRed/White:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

[]4

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 17

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Sienna (G key) 2011-2014

HS CAN High Red 6 Data OBDII Connector. White 16 HS CAN Low White 14 Data OBDII Connector. White 16 SIL White 7 Data OBDII Connector. White 16 SIL Interrupt White 10 Cut

TPMS Connector, (loc ated on the left side of the Dash fuse box.) W hite 12 RDA Pink 26 Data Body ECU. White 30 Parking Lights Yellow 18 (-) Headlight Switc h. White 20 Autolights Violet 19 Cut Headlight Switch. White 20 Ignition 1 Black 6 (+) Ignition Switch. White 8 Ignition 2 Yellow 4 (+) Ignition Switch. White 8 Starter 1 Red 8 (+) Ignition Switch. White 8 12V Red 7 (+) Ignition Switch. White 8

Wire Information Connector Information

Firmware TL7:

Type 7 - Vehicle Wiring Reference Chart

Rev.: 20 914170

Page 17

Page 18

Platform: DBALL2 Firmware TL7:

Installation Type 8

Rev.: 20 914170

Page 18

It is important to make sure you do connect the keysense wire in thNOT is installation or you will encounter issues when attempting to start the vehicle.

[]2

[3] (-) Parking Lights or , p: in 18Black White

20 19

[4]

Make this connection

:, p20Autolights inGreen

only if the vehicle is equipped with Automatic Headlamps.

(-) Hood Status Input

(+) Brake InputStatus

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

Headlight Switch

Starter

Output(-) Parking Lights

(+) 12V Input (+) Starter Output2

Remote

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) Ground

(-) OutputLock

(-) OutputUnlock

(-) Trunk Output

(-) GWR Output

HS CAN , pHigh: in 6Blue SIL:

Diagnostic

onnector OBDIIC

HS CAN Low:

Ignition onnectorC

4321 8765

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

in 7Gray, p

169

in 14White, p

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

Prog utton.B

LED

123

789

DBALL2

3: (-) Trunk InputRed/White:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

CUT

RDA: ,Blue

pin 61

Autolights Interr. (veh. side): 10Orange/Red:

[4]

Autolights Interr. (conn. side): 11Yellow/Red:

[4]

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

RDA: 11Orange/Black:

Body ECU Connector

(middle plug)

456

161718

131415

282930

101112

252627

222324

192021

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data.

[4] Autolights Interrupt only required if vehicles are equipped with Autolights.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 19

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Camry (G Key) 2012-2014

HS CAN High Blue 6 Data OBDII. Black 16 HS CAN Low White 14 Data OBDII. Black 16 SIL Gray 7 Data

OBDII. B lac k 1 6

RDA Blue 16 Data Body ECU. White 30 Parking Lights Black or White 18 (-) Headlight switch. W hite 20 Autolights Green 20 Cut Headlight switch White 20 12V Green 5 (+) Ignition switch. White 8 Acces sory White 2 (+) Ignition switch. White 8 Ignition 1 Black 6 (+) Ignition switch. White 8 Ignition 2 Pink 1 (+) Ignition switch. White 8 Starter 1 Blue 7 (+) Ignition switch. White 8 Starter 2 Lt.Green 3 (+) Ignition switch. W hite 8

Wire Information Connector Information

Firmware TL7:

Type 8 - Vehicle Wiring Reference Chart

Rev.: 20 914170

Page 19

Page 20

Platform: DBALL2 Firmware TL7:

Installation Type 9

Rev.: 20 914170

Page 20

It is important to make sure you do connect the keysense wire in thNOT is installation or you will encounter issues when attempting to start the vehicle.

[]2

[3] (-) Parking Lights , p: in 18Tan

20 19

[4]

Make this connection

:, pAutolights in 19Green

only if the vehicle is equipped with Automatic Headlamps.

CUT

(-) Hood Status Input

(+) Brake InputStatus

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

[3]

Headlight Switch

SIL: , p 0in 1Blue

Starter

Output(-) Parking Lights

Tire Pressure Warning ECU

(Behind glove box)

654321

1211 10 987

(-) Ground

(+) 12V Input

Remote

(+) Starter Output1 (+) Ignition Output2 (+) Ignition Input/Output1

(-) OutputLock (-) OutputUnlock

(-) GWR Output

CAN , pHigh: in 6Violet SIL:

Diagnostic

onnector OBDIIC

Ignition onnectorC

4321 8765

Fuse Box Connector

Refer to the Vehicle Wiring

Reference Information for wire

and connector details.

in 7Tan , p

169

CAN Low:

in 14White, p

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

CUT

SIL Interr. (conn. side) : 8Yellow:

SIL Interr. (veh. side) : 9Orange/Yellow:

Autolights Interr. (veh. side): 10Orange/Red:

[4]

Autolights Interr. (conn. side): 11Yellow/Red:

[4]

(+) 12V

(-) Ground

(-) E-Brake Status Output: 1Black/White:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

[]1 (AC) Tach Output: 5Violet/White:

[]2

(-) Hood Status Output: 12Blue/Red:

(+) 12V : 13Input Red:

(-) Ground: 14Black:

(+) Brake Output: 6Status Gray:

SIL: 10Yellow/Black:

Prog utton.B

LED

DBALL2

10: (-) GWR (Status) InputBlue/White:

9: (+) Ignition InputPink:

2: (-) Unlock InputBlue:

1: (-) Lock InputGreen:

(+)12V

RX (-) Ground TX

P#: XKD2D65

Not required in D2D mode.

[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;

refer to the Vehicle Application Guide for compatibility.

[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter. []3 Parking light output only required if Parking Lights are not supported in data.

[4] Autolights Interrupt only required if vehicles are equipped with Autolights.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

Page 21

Platform: DBALL2

Function Color Pin Polarity Location Color Pins

Toyota Tundra (G Key) 2010-2017

HS CAN High Violet 6 Data OBDII Connector. Black 16 HS CAN Low White 14 Data OBDII Connector. Black 16 SIL Tan 7 Data OBDII Connector. Black 16 SIL Interrupt Blue 10 Cut

TPMS Connector, behind the glove box. White 12 Parking Lights Tan 18 (-) Headlight Switch. White 20 Autolights Green 19 Cut Headlight Switch. White 20 Ignition 1 Black 6 (+) Ignition Switch. White 8 Ignition 2 Lt. Green 1 (+) Ignition Switch. W hite 8 Starter 1 Green 7 (+) Ignition Switch. W hite 8 12V Black 1 (+) Dash Fusebox. White 1

Wire Information Connector Information

Firmware TL7:

Type - Vehicle Wiring Reference Chart9

Rev.: 20 914170

Page 21

Page 22

Platform: DBALL2 Firmware TL7:

Module Programming

Refer to the LED Diagnostics section on page for more information and for troubleshooting purposes.s 24-25

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

Flashing a module using your computer:

1. Connect the interface module to your computer using the XKLoader2.

2. Go to www.directechs.com using Internet Explorer, and select the button.Flash Module

3. Follow the instructions to select your vehicle, installation type, and configure your options.

4. Once you have configured the firmware options, click on the FLASH button.

When the flashing operation is successful, you can proceed with the programming instructions below.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your oader3.XKL

2. Launch the Directechs Mobile app on your smartphone or tablet.

3. Select and follow the on screenFLASH YOUR MODULE instructions.

Rev.: 20 914170

Page 22

D2D Installation

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.

W W Installation2

If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.

The master key module programming .is to complete the successfullyREQUIRED

Wait until the LED turns solid red.ON

Note: To skip the transponder programming and use convenience features only,

press the 5 times.programming button

Insert turnand the key to the ignition position. The turns solidLED ON

green for 3 seconds. This may take up to .5 seconds

Note: If the transponder programming was skipped, the turnsLED ON solid orange for 3 seconds then shuts when programming is done.OFF

Turn the thekey to position.OFF

Key OUT

14-pin

12-pin

14-pin

12-pin

Solid

Green

3 seconds

OFF

IGN

START

D2D

10-pin

D2D

10-pin

Key IN

OFF

IGN

START

You have successfully completed the module programming sequence.

Page 23

Platform: DBALL2 Firmware TL7:

Rev.: 20 914170

Page 32

Module Reset

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

D2D Installation

If required for your installation, c , &onnect the 10-pin 12-pin 14-pin harnesses to the module Press hold the. and p , then connect the 4-pin D2D harness.rogramming button

W2W Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module Press hold the rogramming. and p button, then connect the 14-pin harness to the module.

D2D

10-pin

D2D

10-pin

14-pin

12-pin

14-pin

12-pin

Wait 3 seconds until the orange then release theLED turns solidON

p The then turns solid red.rogramming button. LED ON

& &

Solid Solid

Release

Hard Reset

Warning gainst xecuting a Hard Reset!AE

A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

D2D Installation

If required for your installation, c , &onnect the 10-pin 12-pin 14-pin harnesses to the module Press hold the. and p , then connect the 4-pin D2D harness.rogramming button

D2D

10-pin

14-pin

12-pin

W2W Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module Press hold the rogramming. and p button, then connect the 14-pin harness to the module.

Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsON until the andLED starts to flash orange red.

Release the programming button. The turns solid red.LED ON

D2D

10-pin

14-pin

12-pin

Solid

Flashes

Release

Solid

Page 24

Platform: DBALL2

Feat. Ope ration Fla shes/Option Description

1. Di sable d* Module is connected t o a remote s tarter usi ng a s tandard installati on.

2. RFTD Out put M odule is c onnected to an XL202 using an RSR or RXT installation (when available).

3. S martS tart Module i s connected to SmartS tart using an RSR or RXT installation (when available).

1. Driver Priority* Unloc ks only the driver door on firs t press and unlock s all doors on a s econd press within 5 seconds.

2. A ll Unloc ks all doors on firs t press.

1. Trunk Trunk: Will pop the t runk i f available.

2. Right Sliding Door* When availabl e, will operat e t he right sliding door.

3. Left Sliding Door W hen available, will operate the left s liding door.

1. Trunk Trunk: Will pop the t runk i f available.

2. Right S liding Door When available, will operate the right s liding door.

3. Left Sli ding Door* W hen available, will operat e t he left sliding door.

1. Disabled

The OEM alarm will not be controlled by DBALL upon remote s tart . No disarm or arm c ommand will be executed at the beginning or end of the s equence; it must be controlled by the Remote Starter.

2. S afelock

Smart OEM Alarm Cont rol wil l behave lik e a standard S afelock feature on a remote starter. It will unlock at the begi nning of t he s equence, and reloc k after start and shutdown.

3. Ena bled*

Smart OEM Alarm Cont rol wil l s ync hronize with t he OE M al arm s o that i t will dis arm and rearm the vehicle in the remot e start sequence, only when required. The reas on for t his is, factory alarm c ontrol must often be done by l ock or unloc k operation. This c ould create unnec ess ary actions on door lock modules, s uch as t he horn t o honk . When pos sibl e, Smart OEM Alarm Cont rol wil l monitor the alarm and door loc k status to detect if the disarm or rearm is required. If t he vehicle is unlocked or is not equipped with factory al arm, the dis arm/rearm will not be ex ecut ed. Smart OEM Alarm Cont rol wil l also m onitor the remote starter actions so that t he factory alarm c ontrol is not done twice. A remot e s tarter, for which t he Safelock feature is ac tive, will work perfectly with t his option and will m ake it invisible t o the user.

1. Not Equipped* The vehicle is not equipped with an automat c trunk/hat ch opening system.

2. E quipped The vehicle i s equipped wit h an automatc trunk/ hatc h opening system.

Motoriz ed Hat ch Equipped

AUX2

RF Output Type1

Unlock Driver Priority

(works only wit h t ypes 1 & 3)

AUX1

* Default Option

Smart OEM Alarm Control5

Firmware TL7:

Rev.: 20 914170

Page 42

Feature and Option List

It is recommended to configure all features and options listed below thethe using configuration tool found on the module flashing page on www.directechs.com.The web offers moreoptions; however, manual configuration of the features is possible using the information on this page.

Page 25

Platform: DBALL2 Firmware TL7:

Rev.: 20 914170

Feature Programming

Programming

To enter feature programming routine

Turn t , thenhe ignition .ON OFF

Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( ) Programming button.

The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence will until .a new command is entered

Changing feature options

Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/

The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred

the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

Accessing another feature

Press and release the programming button a number of times to advance from the current feature to the next desired feature.

The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

Once a feature is programmed

Other features can be programmed.

The feature programming can be exited.

Exiting feature programming

No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON sequence. OR

Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ON end of the programming sequence.

Page 52

Button

Page 26

Platform: DBALL2

LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12 Volt is present between the red and black wires. If the 12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.

Ensure the correct programming procedure is being followed.

Initialization failed.

Reset the module and c omplete the programming again. If the is sue persists , please c ontact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detect ed. Normal operation

Key2GO initiated.

Pleas e follow the steps indicated in “Module programming” to complete the Key2GO programming.

Module was succ essfully programmed with all functions . Normal operation

Module was succ essfully programmed without transponder functions.

Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire connections. W ak e up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.

J1850 not detected.

Check the J1850 wire connection. Wake up the dat a bus by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections . Wake up the data bus by turning the ignition on and try again. If your ins tallation does not require this connection, skip this step by pressing t he programming button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehic le still operates correctly using the factory key.

Bypass proc essing error.

The bypass calculation failed. Reset the module and try again. If the c ondition persists, please c ontact Technical Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expect ed signal. Refer to "Installation (wiring diagrams & vehicle wiring reference c harts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference c harts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts )" to check the connections.

Module Programming

Module Programming - Error Codes

Firmware TL7:

LED Diagnostics & Troubleshooting

Off

Solid red

Flashes red & green

Solid orange

Flashes green

Flashes orange

Flashes orange slowly

Solid green x 3 secs

Solid orange x 3 secs

Rev.: 20 914170

Page 62

Flashes red x 1

Flashes red x 2

Flashes red x 3

Flashes red x 4

Flashes red x 5

Flashes red x 6

Flashes red x 7

Page 27

Platform: DBALL2

LED Description Troubleshooting

OBDII feature is not supported.

The diagnostic data bus was not detected, therefore the SmartStart features will be limited.

Ground W hen Running (Status) command rec eived. The module has initialized the remote s tart s equence.

Ignition ON command received.

The module has received the Ignition ON command and is processing the remote s tart s equence.

Start ON command received.

The module has received the Start ON command and is processing the remote s tart s equence.

PTS shutdown error.

The PTS out put from the module was not ac tivated due to safety protec tion.

CAN bus inc orrectly det ected.

Verify the CAN1 and CAN2 connections. Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections .

LOCK command received.

UNLOCK c ommand received.

TRUNK c ommand rec eived.

AUX1 c ommand received.

AUX2 c ommand received.

AUX3 c ommand received.

Takeover successful. Normal operation.

Runsafe was not disabled.

No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode.

Brake was not detected.

The brakes were not detected, whic h prevents t he system from shutting down the vehicle.

Smart key was not detec ted.

The smart key was not detec ted, which prevents t he system from shutting down the vehicle.

Speed was detected.

The vehicle was detected as moving, which prevents the system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

Firmware TL7:

(Flashes red, red then orange) x 10

Flashes green

Flashes red & orange

Flashes green quickly

Flashes red x 10

Flashes red x 21

Rev.: 20 914170

Page 72

Flashes orange x 1

Flashes orange x 2

Flashes orange x 3

Flashes orange x 4

Flashes orange x 5

Flashes orange x 6

Flashes green x 1

Flashes red x 1

Flashes red x 2

Flashes red x 3

Flashes red x 4

Page 28

Platform: DBALL2 Firmware TL7:

Rev.: 20 914170

Page 82

Limited Consumer WarrantyOne Year

For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEAR Electronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTED security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTED and the Part is returned to , postage prepaid, along with a clear, legible copy ofthe receipt or bill of sale bearing theDIRECTED following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING,,, BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY,, , FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY,; PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS, PRODUCTS DIRECTED HEREBY DISCLAIMS AND HASABSOLUTELY NO LIABILITY FOR ANYAND ALLACTS OF. THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR.A INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS,, , , AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION,, LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING,, . A A DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF, CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE. DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED. TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S . RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL,, DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL,, ,, LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE,., MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA’S PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the UnitedStates of America and Canada. Parts sold outside of the United States of America or Canada are sold “ - ” and shall have , expressor implied. Some states do not allow limitationsAS IS NO WARRANTY on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTED not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTED website at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing.Visit website for latest vehicleapplication guide. : Under noDISCLAIMER circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Page 29

Quick Reference Guide

DBALL2-TL7

Button(s)

Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock .

Press & hold for 1 second to remote start.

Press & hold for 5 seconds to activate the trunk release (optional).

Press once, then to activate the rear hatch/tail glass release (optional).*

Press 3 times, then to act ivate the panic mode.

Press once, then to reset the remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more

information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Notes