Directed 9816V, 9816X, 9816P User Manual
RF KIT
Models:
9816V
9816X
9816P
2
© 2015 Directed. All rights reserved.
Congratulations
Congratulations on the purchase of your remote start system. This
system has been designed to provide years of trouble-free operation. By carefully reading this owner’s guide prior to using your
system, you will maximize the use of this system and its features.
For more information please visit us online at: www.viper.com or
www.clifford.com or www.pythoncarsecurity.com.
For any additional questions please contact your authorized
Directed dealer or contact Directed at 1-800-753-0600 (U.S.
only) or 1-800-361-7271 (Canada only). Additional support is
also available at: http://support.directed.com
What You Get
• One 2- way, 1- button remote control
• One 1- way, 1- button remote control
• Owners Guide
Replacement Remote Controls
Please see your authorized dealer or visit us at www.directedstore.com to order additional remote controls. Remote control part
numbers are found on the back of the device.
3
© 2015 Directed. All rights reserved.
Introduction
Mounting The Transceiver [Antenna]
The transceiver’s position should be discussed with the vehicle’s
owner prior to installation since the antenna will be visible to the
customer.
The best position to locate the transceiver is centered high on the
front windshield. It can be mounted vertically or horizontally relative to the windshield. Metallic window tint can also affect range
negatively, so this should be a consideration when determining
the mounting location.
After you determine the best mounting location, follow these steps:
1. Clean the mounting area with a quality glass cleaner or alcohol to remove any dirt or residue.
2. Plug the cable into the transceiver.
3. Mount the transceiver with double-sided tape.
4. Route the cable down the window pillar to the control module and plug the cable in the control module.
TRANSCEIVER /
ANTENNA CABLE
TRANSCEIVER / ANTENNA
4
© 2015 Directed. All rights reserved.
Once the transceiver (and LED/Valet button if applicable), has
been installed, the remote controls will need to be paired with the
system. See “Remote Pairing” to pair the remote controls with your
system. For more specific programming instructions, please refer
to the programming instructions in your system’s owner’s guide.
Remote Control Commands
System State Press/Release button Press/Hold for 3 sec.
Engine OFF START ENGINE CAR FINDER*
Engine ON UNLOCK DOORS STOP ENGINE
*This option is only available when using a 4X10.
Note: Please refer to your system’s owners guide for more
details on how to use your remote control.
Note: If a feature cannot be activated when performing a
command with the 2-way remote control, a fault tone plays
as an alert.
Start Engine
When the engine is OFF, press and release the remote control
button to start the engine.
Unlock Doors
When the engine is ON with remote start, press and release the
re mote control button. The doors unlock, the parking lights flash
and the horn sounds* (if connected) as confirmation. The 2-way
remote control emits tones.
*This option is only available when using a 4X10.
5
© 2015 Directed. All rights reserved.
Note: Horn honk may be an optional feature that requires
additional parts and labor.
Stop Engine
When the engine is ON with remote start, press and hold the
remote control button until the transmit LED flashes fast. The engine
stops run ning and the parking lights turn off. The 2-way remote
control emits tones.
Car Finder*
When the engine is OFF, press and hold the remote control button
for three seconds. The horn sounds once (if connected) and the
parking lights flash multiple times. The 2-way remote control emits
a single tone.
*This option is only available when using a 4X10.
6
© 2015 Directed. All rights reserved.
Remote Pairing
With a 4X10 :
Use the following procedure to pair an additional or replacement
remote control to the system.
1. Turn the ignition to the ON position.
2. Within 10 seconds, press/release once and then press and
hold the control button on the system’s control center. The status LED begins flashing in a sequence of 1 flash and the horn
sounds to confirm the system is ready for pairing. Release the
control center button.
3. Press and release the remote control button twice quickly,
and then press and hold it. The transmit LED comes on solid,
continue to hold the button until the transmit LED changes
its pattern. Release the button and the transmit LED begins
flashing as an indication that the remote has entered the
pairing mode.
4. Press and release the button on the remote control.
5. The horn sounds as a confirmation the system has paired
with the remote control and the 2-way remote plays tones
confirming that the remote has paired with the system (the
1-way remote does not offer confirmation tones). The remote
will automatically exit the pairing mode after 30 seconds
or you can manually exit the pairing mode by pressing and
holding the button on the remote, the remote will emit a tone
confirming exit. If pairing fails repeat steps 3 - 6.
6. Turn the ignition off or wait 60 seconds for the system to exit
the pairing mode, the horn will sound as confirmation.
7
© 2015 Directed. All rights reserved.
With an Xl202 :
1. Press the button on the remote control twice and then hold on
the third press. The transmit LED will come on solid, continue
to hold the button until the transmit LED changes its pattern.
Release the button and the transmit LED will begin flashing as
an indication that the remote has entered the pairing mode.
2. Press and hold the programming button of the XL202 module. The LED will begin flashing slowly (Do Not Release the
XL202 Programming Button).
3. Press the button on the remote control. The LED on the XL202
will turn on solid for one second, then LED then turns off to
indicate that pairing was completed successfully. If Remote
Pairing fails repeat the above procedure or confirm the firmware flashed to the XL202 is correct for the type Antenna/
Remote you are using.
Note: The 2way remote will play tones confirming that the
remote has paired with the system.
4. Release the programming button on the XL202.
The programming routine exits if any of the following occurs:
• The ignition is turned off
• There is no activity for 30 seconds
• The Control Center button is pressed too many times
8
© 2015 Directed. All rights reserved.
Battery Information
The 1-way remote controls are powered by a single coin cell battery (CR-2016), and the 2-way remote controls are powered by
two coin cell batteries (CR-2016) that can be purchased at most
retailers. Operating range diminishes as battery charge depletes.
Battery Replacement
1. Unscrew the hardware on unit rear and remove from housing.
2. Hold the unit base with one hand and gently twist and pull
the main housing body with the other. This releases all parts
of the housing assembly.
3. Remove battery from clip and replace with a new one while
observing the correct polarity.
4. Reassemble unit and secure with hardware. Replace screw.
Battery Disposal
Directed cares about the environment. If you need to
dispose of the battery, please do so in accordance
with your municipal requirements for battery disposal.
9
© 2015 Directed. All rights reserved.
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote
start or security product, Directed Electronics. (“DIRECTED”) promises to the original
purchaser, to repair or replace with a comparable reconditioned piece, the security or
remote start accessory piece (hereinafter the “Part”), which proves to be defective in
workmanship or material under normal use, provided the following conditions are met:
the Part was purchased from an authorized DIRECTED dealer; and the Part is returned
to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of
sale bearing the following information: consumer’s name, address, telephone number,
the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified
or used in a manner contrary to its intended purpose or the Part has been damaged by
accident, unreasonable use, neglect, improper service, installation or other causes not
arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL
WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR
PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY
IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS
ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING
DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR
INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE,
ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE,
OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED
OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE
STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS
Loading...