Directed 4113, 1-button series, 4x03 Installation Manual
Installation Guide
Keyless Entry Remote Start
4113, 1-button series
This product is intended for installation by a professional
installer only! Attempts to install this product by a person other than a trained professional may result in severe
damage to a vehicle’s electrical system and components.
© 2012 Directed, Vista, CA
N4113 2012 01
N4111 2012 01
Bitwriter®, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance
Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®,
Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn
Away® are all Trademarks or Registered Trademarks of Directed Electronics.
The Bitwriter® (p/n
998U) requires chip
version 2.7 or newer to
program this unit.
Bitwriters with a date code of 6a or older require an IC
upgrade (p/n 998M). Some Bitwriters with a date code of
6B do not require the IC upgrade, refer to tech tip # 1112
for more information.
Contents
Warning! Safety first ....................................................................................................................... 4
Wiring diagram .............................................................................................................................. 5
Wiring connections ......................................................................................................................... 5
Main Harness (H1), 9-pin connector ............................................................................................ 5
Door Lock - 3 pin connector ........................................................................................................ 6
Heavy Gauge Relay (H2), 6-pin connector ................................................................................... 6
Satellite harness - 4-pin connector ................................................................................................ 6
Remote Start harness (H3) 5-pin connector ................................................................................... 6
Tach Learning ................................................................................................................................. 7
Virtual Tach .................................................................................................................................... 7
Neutral safety switch interface .......................................................................................................... 8
Testing the neutral safety switch ................................................................................................... 8
Remote start shutdown diagnostics .................................................................................................... 9
Remote programming ...................................................................................................................... 9
Programming system features .......................................................................................................... 10
1-button remote / Model 4113 ................................................................................................. 10
Feature menus .............................................................................................................................. 11
Menu 1 ................................................................................................................................. 11
Menu 2 ................................................................................................................................. 13
Red 4-pin port, Bitwriter/ESP2 or D2D programming .................................................................. 14
Bitwriter only options ..................................................................................................................... 15
Bitwriter feature descriptions ..................................................................................................... 15
Basic remote functions ................................................................................................................... 16
1-button remote / Model 4113 ................................................................................................ 16
Reset and deletion ......................................................................................................................... 17
Troubleshooting: Keyless entry ........................................................................................................ 17
Troubleshooting: Remote start ......................................................................................................... 17
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized
Directed Electronics dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control.
Therefore, never operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed Electronics
dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote
start system must be disabled using the installed toggle switch. It is the user’s sole responsibility to prop-
erly handle and keep out of reach from children all remote controls to assure that the system does not
unintentionally remote start the vehicle.
USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL
DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST
REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage,
personal injury, or death. Except when performing the Safety Check outlined in this installation guide,
(1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the
keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically
checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed
by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the
user to fix the problem immediately.
After the remote start module has been installed, test the remote start module in accordance with the Safety
Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown
Circuit test, the remote start unit has not been properly installed. The remote start module must be removed
or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an
authorized Directed Electronics dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS
MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT
AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED ELECTRONICS WILL
NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
IMPORTANT! This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in a
standard transmission vehicle is dangerous and is contrary to its intended use.
4
© 2012 Directed. All rights reserved.
Wiring diagram
Parking light jumpers
Side View
Heavy
Gauge
Relay
Satellite Harness
Wiring connections
Red 4-pin port, Bitwriter/ ESP2 or D2D
4x03
Primary Harness Remote Start Harness
Antenna
Side View
LED (Programming
indicator)
Control Button
(Valet Switch)
Door Lock/unlock
Harness
Antenna
Main Harness (H1), 9-pin connector
LIGHT GREEN
H1/1
BLACK
GREEN/WHITE (-) 200mA FACTORY ALARM REARM
H1/2
YELLOW (+) IGNITION OUT (TO ALARM)
H1/3
WHITE/BLUE (-) ACTIVATION INPUT
H1/4
ORANGE (-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT
H1/5
BROWN (-) 200mA HORN OUTPUT
H1/6
RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT*
H1/7
BLACK GROUND
H1/8
WHITE (+/-) LIGHT FLASH OUTPUT
H1/9
* Not available on 1-button remote
© 2012 Directed. All rights reserved.
(-) 200mA FACTORY ALARM DISARM
5
Door Lock - 3 pin connector
LIGHT BLUE (-) UNLOCK
1
EMPTY NOT USED
2
GREEN (-) LOCK
3
Heavy Gauge Relay (H2), 6-pin connector
PINK OUTPUT TO PRIMARY IGNITION CIRCUIT
H2/1
PURPLE OUTPUT TO STARTER CIRCUIT
H2/2
ORANGE OUTPUT TO ACCESSORY CIRCUIT
H2/3
RED (+) 30A HIGH CURRENT 12V INPUT
H2/4
PINK/WHITE OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT
H2/5
RED (+) 30A HIGH CURRENT 12V INPUT
H2/6
Satellite harness - 4-pin connector
BLUE (-) 200mA STATUS OUTPUT
1
ORANGE (-) 200mA ACCESSORY OUTPUT
2
PURPLE (-) 200mA STARTER OUTPUT
3
PINK (-) 200mA IGNITION OUTPUT
4
Remote Start harness (H3) 5-pin connector
H3/1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT
H3/2 VIOLET/WHITE TACHOMETER INPUT WIRE
H3/3 BROWN (+) BRAKE SHUTDOWN INPUT WIRE
H3/4 GRAY (-) HOOD PIN SWITCH SHUTDOWN WIRE
H3/5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER
6
© 2012 Directed. All rights reserved.
Loading...