DIODS ES2G Datasheet
Features
Glass Passivated Die Construction
·
Super-Fast Recovery Time For High Efficiency
·
Low Forward Voltage Drop and High Current
·
Capability
Surge Overload Rating to 50A Peak
·
Ideally Suited for Automated Assembly
·
Plastic Material: UL Flammability
·
Classification Rating 94V-0
NEW PRODUCT
Mechanical Data
Case: Molded Plastic
·
Terminals: Solder Plated Terminal -
·
Solderable per MIL-STD-202, Method 208
Polarity: Cathode Band or Cathode Notch
·
Weight: 0.093 grams (approx.)
·
· Marking: Type Number
ES2G
2.0A SURFACE MOUNT SUPER-FAST RECTIFIER
A
B
C
D
E
G
H
J
SMB
3.30 3.94
4.06 4.57
1.96 2.21
0.15 0.31
5.00 5.59
0.10 0.20
0.76 1.52
2.00 2.62
B
A
C
Dim Min Max
D
J
H
G
E
All Dimensions in mm
Maximum Ratings and Electrical Characteristics
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Characteristic Symbol ES2G Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
RMS Reverse Voltage
Average Rectified Output Current @ TT= 110°C
Non-Repetitive Peak Forward Surge Current
8.3ms Single half sine-wave Superimposed on Rated Load
(JEDEC Method)
Forward Voltage @ IF= 2.0A
Peak Reverse Current @ TA= 25°C
at Rated DC Blocking Voltage @ T
Reverse Recovery Time (Note 3)
Typical Junction Capacitance (Note 2)
Typical Thermal Resistance, Junction to Terminal (Note 1)
Operating and Storage Temperature Range
Notes: 1. Unit mounted on PC board with 5.0 mm
2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC.
3. Measured with I
= 0.5A, IR= 1.0A, Irr= 0.25A. See Figure 5.
F
= 125°C
A
2
(0.013 mm thick) copper pads as heat sink.
V
V
V
R(RMS)
I
V
I
R
T
j,TSTG
RRM
RWM
V
R
I
O
FSM
FM
RM
t
rr
C
qJT
j
@ TA= 25°C unless otherwise specified
400 V
280 V
2.0 A
50 A
1.25 V
5.0
350
25 ns
25 pF
20 °C/W
-55 to +150 °C
mA
DS30212 Rev. A-2 1 of 2 ES2G
g
60
1000
g
0
.75
g
g
10
2.0
1.6
1.2
1.0
T=25Cj°
Pulse width = 300 sµ
0.8
NEW PRODUCT
0.4
O
I , AVERAGE FORWARD CURRENT (A)
0
50
40
30
20
10
25 50
T , TERMINAL TEMPERATURE ( C)
Fi
75
100 125 150 175
T
. 1 Forward Current DeratingCurve
Single Half-Sine-Wave
°
(JEDEC Method)
0.1
F
I , INSTANTANEOUS FORWARD CURRENT (A)
0.01
0 0.4 0.8 1.2 1.6
V , INSTANTANEOUS FORWARD VOLTAGE (V)
F
Fi
.2 Typical Forward Characteristics
µ
T = 125 Cj°
100
10
T=25C
°
j
1.0
FSM
I , PEAK FORWARD SURGE CURRENT (A)
0
1 10 100
NUMBER OF CYCLES AT 60Hz
. 3 Surge Current DeratingCurve
Fi
50 NI (Non-inductive)Ω
Device
Under
(+)
50V DC
Approx
(-)
Notes:
1. Rise Time = 7.0ns max. Input Impedance = 1.0M , 22pF.
2. Rise Time = 10ns max. Input Impedance = 50 .ΩΩ
Test
1.0NIΩ
Oscilloscope
(Note 1)
Fig. 5 Reverse RecoveryTime Characteristic and Test Circuit
10 NIΩ
(-)
Pulse
Generator
(Note 2)
(+)
R
I , INSTANTANEOUS REVERSE CURRENT ( A)
0.1
0 40 80 120
PERCENT OF RATED PEAK REVERSE VOLTAGE (%)
.4 Typical Reverse Characteristics
Fi
t
+0.5A
0A
-0.25A
-1.0A
rr
Set time base for 50/100 ns/cm
DS30212 Rev. A-2 2 of 2 ES2G
Loading...