Dimplex Xpression SP220, Xpression SP2 Installation And Operating Instructions Manual

Pelgrim

bracket
rotated
from transit
position

fixed
socket
outlet

min.

100 495

587

180

Side

Front

300
min.

Heat

Out

Air

In

Controls
(see Fig. 6)

Viewing
Screen

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.

Dimensions

(millimetres)

Installation and Operating Instructions

Electrical

08/18802/1 Issue 1

Fig. 1

Important Safety Advice:

When using electrical appliances, basic
precautions should be followed to reduce the risk
of fire, electric shock, and injury to persons,
including the following :

• If the appliance is damaged, check

immediately with the supplier before
installation and operation.

• Do not use this heater in the immediate

surroundings of a bath, shower or swimming
pool

.

• Do not use outdoors.

• This heater must not be located immediately

above or below a fixed socket outlet or
connection box.

• Do not cover or obstruct in any way the heat
outlet grille located underneath the heater.
Overheating will result if the heater is
accidentally covered.

• In the event of a fault unplug the heater.

• Unplug the heater when not required for long

periods.

• The supply cord must be placed on the right
hand side of the heater away from the heat
outlet underneath the heater.

• Although this heater complies with safety

standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.

• Do not leave young children, the elderly, or
the infirm unsupervised in the vicinity of the
heater.

• The appliance must be positioned so that the

plug is accessible.

• If the supply cord is damaged it must be
replaced by the manufacturer or service agent
or similarly qualified person in order to avoid
a hazard.

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Do not switch the appliance on until properly installed. Please
read all the safety warnings and operating instructions.

Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
fire to your supplier.

Contents of Carton.

• SP2 Heater.

• Wall fixing bracket.

• Three fixing screws and three wall plugs.

• Remote control and batteries (3 AAA’s type).

• Spare bulb.

Do not connect the heater to an electricity supply until it is
installed on a wall correctly. - see ‘Installation’.
A choice of 1kW or 2kW heat output is provided by the fan
heater, which is concealed underneath the unit.
The heater can be used remotely or manually. - see
‘Operation’.
General features of remote control are:

• Heat output can be increased or decreased

according to your particular requirements.

• The illumination of fuel effect can be increased or

decreased.

• Programmable timer.

Please note: Used in an environment where background
noise is very low, it may be possible to hear the fan which
operates the flame effect. This is normal and should not be
a cause for concern.

General

Xpression Wall fire SP2
Model No: SP220

ensure ledge
at back of
fire engages
wall bracket

c

Detail '1'

ledge

wall
bracket

a

lift appliance
above wall
fixing bracket

rotate bottom
fixing bracket
down from its
transit position

slide down over
bracket, ensure
that ledge of
appliance engages
behind wall
bracket and is
central

bring level

with wall

d

wall bracket

b

see
detail '1'

wall fixing

bracket

screws

wall
plugs

wall
holes

Installation

Recommended Fixing Dimensions - Fig. 2

Fig. 3

Fig. 5

Mark the bottom hole position (see Fig. 5), remove the heater
ensuring that the bottom fixing bracket is rotated up.

Drill and fit wall plug.

Refit the heater to the wall fixing bracket (i.e. follow steps as
in Fig. 4 a,b,c and d above) and rotate the bottom fixing
bracket down again and use the screw provided to
permanently fix the heater in place.

The heater should not be connected until the instruction leaflet
is read fully.

Do not connect appliance until properly fixed to the wall
and the Instruction leaflet is read fully.

This model is designed to be permanently fixed to a wall at a
minimum height of 300mm.

The wall bracket must be fitted horizontally with the cable
routed to the bottom right of the heater as in Fig 1.

A height of 600mm from bottom of heater to floor is
recommended for optimum viewing of fuel bed (see Fig. 2
for recommended fixing dimensions).

For optimum viewing mark the top two screw fixing positions
on wall in accordance with the recommended fixing
dimensions - see Fig. 2.

Fix the wall bracket using the two plugs and screws provided

- see Fig 3.

Carefully lift the heater up ensuring that the top rear ledge of
heater engages the wall bracket and is sitting centrally
positioned. - see Fig 4 (b).

Rotate the bottom fixing bracket down. - see Fig 4 (c).

Gently bring the heater level with the wall. - see Fig 4 (d).

120

outline of
wall fire

526

120

240

13

600

1113

513

outline of wall
fixing bracket

Fig. 4

outline of
wall fire

mark hole
centre with
pencil

outline of
wall fire

Neon's for
indicating
operation
level

(1kW/2kW) Heat

(Switch 3)

Manual Controls

Dimmer

(Switch 4)

Manual/Automatic

(Switch 2)

Standby (ON/OFF)

(Switch 1)

MAN.

AUTO

OFF

ON

Manual Operation

The Standby Switch (Switch 1) must be first turned ‘ON’ and
the AUTO/MAN (Switch 2) switch set to ‘MANUAL’ to operate
the manual controls - see Fig 6.

Note : When the fire is put in Manual mode the first time the
flame effect will come on indicated by the Bottom neon coming
on for 3 seconds - see Fig 7.

Setting Operation Indication

Flame Effect Bottom Neon

Flame Effect & 1Kw Heat Press the ‘ I ’ button (Switch 3) Middle Neon

Flame Effect & 2Kw Heat Press the ‘ I ’ button again (Switch 3) Top Neon

To go to the previous settings press the ‘ O ‘ button (Switch

3).

To increase or decrease the brightness of the flames, use
the dimmer button (Switch 4). You can have any setting
between full brightness and the flames totally off. The heat
setting will remain the same.

To turn off the power the Standby Switch (Switch 1) must be
turned ‘OFF’.

Note : Every time that manual mode is selected the previous
light and heat settings come on automatically.

Fig. 6

Fig. 7