THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Dimensions
(millimetres)
Installation and Operating Instructions
Electrical
08/18887/1 Issue 1
Fig. 1
Important Safety Advice:
When using electrical appliances, basic
precautions should be followed to reduce the risk
of fire, electric shock, and injury to persons,
including the following :
• If the appliance is damaged, check
immediately with the supplier before
installation and operation.
• This heater must not be used if the front glass
is damaged.
• Do not use this heater in the immediate
surroundings of a bath, shower or swimming
pool.
• Do not use outdoors.
• This heater must not be located immediately
above or below a fixed socket outlet or
connection box.
• Do not cover - Overheating will result if the
heater is accidentally covered.
• In the event of a fault unplug the heater.
• Unplug the heater when not required for long
periods.
• Although this heater complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
• Do not leave young children, the elderly, or
the infirm unsupervised in the vicinity of the
heater.
• The appliance must be positioned so that the
plug is accessible.
• If the supply cord is damaged it must be
replaced by the manufacturer or service agent
or similarly qualified person in order to avoid
a hazard.
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Do not switch the appliance on until properly installed. Please
read all the safety warnings and operating instructions.
Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to
your supplier.
Contents of Carton.
• SP4 Heater.
• Wall fixing bracket.
• Six fixing screws and six wall plugs.
• Remote control and batteries ( 3 AAA’s type).
• Spare bulb.
Do not connect the heater to an electricity supply until it is
installed on a wall correctly. - see ‘Installation’.
When in operation there is a 300 watt heat output from the
fuel effect, and an additional 120 watt output when the heated
glass panel is in operation.
The heater can be used remotely or manually. - see ‘Operation’.
General features of remote control are:
• Activate/Deactivate heated glass panel.
• The illumination of fuel effect can be increased or
decreased.
• Programmable timer.
Please note: Used in an environment where background noise
is very low, it may be possible to hear the motor which operates the flame effect. This is normal and should not be a cause
for concern.
General
Wall Fire SP4
Model No: SP420
8
566
240
600
1158
558
480
outline of wall
fixing bracket
wall
plugs
screws
wall
fixing
bracket
Installation
Recommended Fixing Dimensions - Fig. 2
Fig. 3
Fig. 4
Fig. 5
Mark the bottom hole position (see Fig. 5), remove the heater
ensuring that the bottom fixing bracket is rotated up.
Drill and fit wall plug.
Refit the heater to the wall fixing bracket (i.e. follow steps as
in Fig. 4 a,b,c and d above) and rotate the bottom fixing
bracket down again and use the screw provided to
permanently fix the heater in place.
The heater should not be connected until the instruction leaflet
is read fully.
Do not connect appliance until properly fixed to the wall
and the Instruction leaflet is read fully.
This model is designed to be permanently fixed to a wall at a
minimum height of 300mm.
The wall bracket must be fitted horizontally and the cable
routed to the bottom right of the heater as in Fig 1.
Drill holes with a 6mm drill bit. Fix the wall bracket using the
four plugs and screws provided - see Fig 3.
Carefully lift the heater up ensuring that the top rear ledge of
heater engages the wall bracket and is sitting centrally
positioned. - see Fig 4 (b).
Rotate the bottom fixing bracket down. - see Fig 4 (c).
Gently bring the heater level with the wall. - see Fig 4 (d).
outline of
wall fire
mark hole
centre with
pencil
wall
bracket
ledge
ensure ledge
at back of
fire engages
wall bracket
Detail '1'
wall bracket
see
detail '1'
a
lift appliance
above wall
fixing bracket
rotate bottom
fixing bracket
down from its
transit position
c
d
bring level
with wall
slide down over
bracket, ensure
that ledge of
appliance engages
behind wall
bracket and is
central
b
A height of 600mm from bottom of heater to floor is
recommended for optimum viewing of fuel bed (see Fig. 2
for recommended fixing dimensions).
For optimum viewing mark the top four screw fixing positions
on wall in accordance with the recommended fixing
dimensions - see Fig. 2.
Manual Operation
The Standby Switch (Switch 1) must be first turned ‘ON’ and
the AUTO/MAN (Switch 2) switch set to ‘MANUAL’ to operate
the manual controls - see Fig 6.
Note : When the fire is put in Manual mode the first time the
flame effect will come on indicated by the Bottom neon coming
on for 3 seconds - see Fig 7.
To go to the previous settings press the ‘ O ‘ button (Switch
3).
To increase or decrease the brightness of the flames, use
the dimmer button (Switch 4). You can have any setting
between full brightness and the flames totally off. The heat
setting will remain the same.
To turn off the power the Standby Switch (Switch 1) must be
turned ‘OFF’.
Note : Every time that manual mode is selected the previous
light and heat settings come on automatically.
Fig. 6
Fig. 7
Manual Controls
Neons for
indicating
operation level
OFFAUTO
MAN
ON
Flame Effect only
Bottom Neon
Press the ‘ I ’ button (Switch 3)
Setting
Indication
Operation
Flame Effect & Heat On
Top Neon
Press the ‘ I ’ button again (Switch 3)
Loading...