Owner’s Manual
6909410210
6909410110
6909680110
Model
VF5452L
VF2927L
VFA2927
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
Opti-V
. For your safety, always
7213460100R05
Table of Contents
Welcome & Congratulations ..................3
IMPORTANT SAFETY INSTRUCTIONS ......... 4
Opti-V Installation ..........................6
Locating the Opti-V .........................6
Hardwire Installation ........................6
Operation ................................10
Maintenance .............................12
Warranty ................................ 13
Technical Support .........................15
Always use a qualied technician
or service agency to repair
this Opti-V.
2 www.dimplex.com
!
NOTE: Procedures and
techniques that are considered
important enough to emphasize.
CAUTION: Procedures and
techniques which, if not carefully
followed, will result in damage to
the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations
Thank you and congratulations for purchasing an Opti-V from Dimplex.
Please use our convenient online registration page to record your
model and serial numbers for future reference at
www.dimplex.com/register
MODEL
MODELE
6909410100
MODELO
North America Limited
CAT.#
VF2927L
No. de Cat.
DIMPLEX NORTH AMERICA
1367 INDUSTRIAL ROAD
CAMBRIDGE, ON, N1R 7G8
100-240V ~, 50/60HZ, 35W
CANADA
SERIAL No./No DE SERIE/No DE SERIE
DDDYYSLF - XXX
PROTECTED BY THE FOLLOWING PATENTS / PROTEGE PAR LES BREVETS SUIVANTS / PROTEGIDO POR LAS SIGUIENTES
PATENTES : US PATENTS / BREVETS DE ETATS UNIS / PATENTES DE ESTADOS UNIDOS : 8,361,367
OTHER PATENTS PENDING / AUTRES BREVETS EN INSTANCE / OTRAS PATENTES PENDIENTES
MADE IN IRELAND
FAIT EN IRLANDE
HECHO EN IRLANDA
Intertek
xxxxxxx
Model Number
Serial Number
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in
a possible electric shock, re hazard and will void the warranty.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
In order to better serve you, please have your model and serial number
ready or register your product online before calling (See above)
3
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances,
basic precautions should always be
followed to reduce the risk of fire,
electric shock, and injury to persons,
including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. The appliance shall not be
exposed to dripping or splash-
ing and that no objects lled with
liquid, such as vases, shall be
placed on the apparatus.
WARNING: To reduce the risk of
re or electric shock, do not expose
this apparatus to rain or moisture.
7. Clean only with dry cloth.
8. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
9. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other ap-
paratus (including ampliers) that
produce heat.
10. No naked ame sources, such as
candles should be placed on this
apparatus.
11. Only use attachments/accessories
specied by the manufacturer.
12. Use only with the cart, stand, tri-
pod, bracket, or table specied by
the manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13. Disconnect power at the service
panel during lightning storms or
when unused for long periods of
time.
14. Refer all servicing to qualied
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
15. If the appliance is damaged,
check immediately with the
supplier before installation and
operation.
16. Do not operate any unit with a
damaged cord, or if the Opti-V
has been dropped or damaged
in any manner, contact Dimplex
Technical Service at
1-888-346-7539.
17. Do not modify the Opti-V. Use it
4 www.dimplex.com
IMPORTANT SAFETY INSTRUCTIONS
only as described in this manual.
Any other use not recommended
by the manufacturer may cause
re, electric shock or injury to
persons.
18. When transporting or storing the
unit and cord, keep in a dry place,
free from excessive vibration and
store so as to avoid damage.
19. Do not install the remote control
battery backwards; charge; put
in excessive heat such as re,
sunshine or the like; or mix with
used or other battery types - may
explode or leak causing injury.
20. When replacing the battery
ensure that it is replaced with
alkaline 1.5 Volt (AAA) batter-
ies. Battery must be recycled or
disposed of properly. Check with
your Local Authority or Retailer for
recycling advice in your area.
!
NOTE: To disconnect from mains
- set the mains switch to 'O'. The
mains (power) switch is located at
the top left hand side of the appliance
above the manual controls - see 'O/I'
Figure 2. Mains switch shall remain
readily operable.
WARNING: To prevent injury, this
apparatus must be securely attached
to the oor/wall in accordance with
the installation instructions.
WARNING: Remote control contains small batteries. Keep away from
children. If swallowed, seek medical
attention immediately.
!
NOTE: Changes or modications
not expressly approved by the party
responsible for compliance could void
user's authority to operate the equipment.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
SAVE THESE INSTRUCTIONS
5
Opti-V Installation
WARNING: ANY INSTALLATION AND SERVICE WORK
CAN ONLY BE PERFORMED BY
QUALIFIED AND AUTHORIZED
PERSONNEL. ALL INSTALLATIONS MUST COMPLY WITH
ALL LOCAL CODES AND BYLAWS, AND INSPECTED AND
APPROVED FOR OPERATION
BY LOCAL GOVERNING AUTHORITY PRIOR TO USE.
WARNING: Construction
and electrical outlet wiring must
comply with local building codes
and other applicable regulations
to reduce the risk of re, electric
shock and injury to persons.
Locating the Opti-V
The Opti-V uses an illusory reection technique and is designed
to work best when ambient light
levels are low. If the Opti-V is
installed in brightly lit areas, the
strong reections may diminish
the ame.
Depending on your specic ap-
plication, installation of the unit
at a height appropriate for the
viewers enjoyment is important. It
is recommended that the following guidelines be used for locating
the unit.
!
NOTE: Measurements are to
the bottom of the viewing area of
the ame.
For standing applications:
Maximum - 51 in. (129.5 cm)
Minimum - 26 in. (66.0 cm)
For sitting applications:
Maximum - 36 in. (91.4 cm)
Minimum - 26 in. (66.0 cm)
Hardwire Installation
The Opti-V is supplied in an assembled state and is designed to
be permanently installed. The unit
comes ready for hardwire installation.
WARNING: Do not attempt
to wire your own new outlets or
circuits. To reduce the risk of re,
electric shock or injury to persons,
always use a licensed electrician.
WARNING: Ensure that the
On/Off switch is set to the Off position (refer to Operation section)
and that the circuit on which the
Opti-V is to be installed has the
power cut off at the service panel
until installation is complete.
!
NOTE: Please read all instruc-
tions before installing.
1. For rough in framing, the
opening should follow the
6 www.dimplex.com
Opti-V Installation
B
recommended dimensions
located in Figure 1.
!
NOTE: Dimensions provided
are minimum clearances and will
vary depending on type of support
framing and nishing options.
!
NOTE: Framing should be
constructed to support:
VF2927L / VFA2927 - 63 lbs (29 kg)
VF5452L - 116 lbs (52 kg)
2. Allow up to 4 ft. (121.9 cm) of
service cable for connecting
Figure 1
C
E
A
D
a power supply wire to the
cable clamp on the Opti-V
when installing before nishing wall.
!
NOTE: A 15 amp, 120 volt
alternating current (VAC) circuit
is recommended, but the unit is
constructed that it can operate
using voltages from 120-240VAC.
!
NOTE: Use minimum 14 AWG
supply cable with two insulated
copper conductors (white and
black) and one bare ground wire.
F
G
A B C D E F G
VF5452L
VF2927L
VFA2927
7
54.5 in
(1380 mm)
30.0 in
(762 mm)
30.0 in
(762 mm)
17.7 in
(450 mm)
17.7 in
(450 mm)
17.7 in
(450 mm)
(345 mm)
(345 mm)
(345 mm)
13.6 in
13.6 in
13.6 in
2.9 in
(74 mm)
2.9 in
(74 mm)
2.9 in
(74 mm)
5.3 in
(135 mm)
5.3 in
(135 mm)
5.3 in
(135 mm)
18.6 in
(474 mm)
18.6 in
(474 mm)
18.6 in
(474 mm)
55.3 in
(1404 mm)
30.5 in
(775 mm)
30.5 in
(775 mm)
Opti-V Installation
Do not use cable with aluminum conductors.
!
NOTE: It is recommended that
all drywall installation and nishing be completed after unit is fully
installed.
3. In the upper left hand corner
of the unit, loosen the two
securing screws and remove
the electrical cover panel.
(Figure 2)
4. Install a ⅜ in. (10 mm) or ½
in. (13 mm) cable connector, not included, suitable for
mounting in a ⅞ in. (22 mm)
hole, to the cable plate and
feed the supply cable through
the connector and secure.
5. Place the unit in the framed
opening, level with shims if
Figure 2
Grounding
Screw
Cable Plate
Cable Clamp
Hole
necessary and attach unit to
frame using mounting anges
provided (Figure 3).
CAUTION: When inserting
the unit take care not to damage
or pinch any of the power cables
that are concealed in the wall.
6. Remove the outer jacket and
strip the individual conductors
½ in. (1.3 cm) from the end.
7. Connect the black wire from
the unit to the Live (120V) or
Line 1 (240V) wire from the
power supply using a wire
connector (included).
8. Connect the white wire from
the unit to the Neutral (120V)
or Line 2 (240V) from the
power supply using a wire
connector (included).
Figure 3
Electrical
Cover Panel
8 www.dimplex.com
Mounting
Flanges
Opti-V Installation
!
NOTE: Cap any additional
wires from the power supply not
used in the installation.
9. Ensure that the green ground-
ing wire is securely attached
to the back plate.
CAUTION: Ensure the
wire connectors are securely
tightened, so no bare wires (live
or neutral) are exposed.
10. Ensure the grounding wire of
the supply cable is securely
attached to the grounding
screw.
!
NOTE: The wire connections
on the Opti-V feed into a 3-prong
plug just below the electrical cavity opening, before closing the
electrical cover ensure that the
plug is fully installed.
11. Reinstall the electrical cover
panel.
12. Reinstall the protector sheet
to prevent dust from entering
the unit while nishing the
surround.
13. Finish surrounding wall.
There are 3 different options
for nishing the wall:
• Permanent - install drywall
right up to the ange that surrounds the opening.
• Semi Permanent - nish
around edge using ashing
material (not included)
• Flexible - create opening big
enough to access mounting
anges and a false front that
can be removed.
9
Operation
Figure 2
A
DC
F
EB
IR Remote Sensor
WARNING: This Opti-V must
be properly installed before it is
used.
The power switch (Figure 2A) must
rst be switched "I" to operate the
appliance.
An ‘Opti-V’ logo will appear on
the screen for about 3 seconds
before the ame picture starts .
!
NOTE: The user may notice a
blank screen for approximately 5
seconds, every 30 minutes. This
is normal and should not be a
cause for concern.
Manual Operation
The manual controls for the
screen are located at the inner
top left hand side of the appliance
above the glass.(Figure 2).
The mains (power) switch (Figure
2A) may be used to switch the
appliance Off ("O") when it is not
required, for example, overnight
or for long periods, to avoid unnecessary energy use.
!
NOTE: Ensure that the mains
(power) switch shall remain readily operable.
The standby button " "
2B) is located just below the pow-
(Figure
er switch. A red light will indicate
when the unit is in standby mode.
(Figure 2)
The volume of the sound effects
may be adjusted up or down by
pressing the volume control buttons (Figure 2C & 2D).
The screen brightness can be adjusted using the (Figure 2E) and
(Figure 2F) buttons. The but-
ton darkens the screen and the
10 www.dimplex.com
Operation
button brightens the screen.
!
NOTE: On the VF5452L there
are brightness controls for each
LED screen. The brightness
controls for the right screen are
located in the center of the unit.
Remote Control Operation
The remote control may be
operated once the appliance is
switched to the ON "I" position
(Figure 2A).
Aim the remote control at the IR
remote sensor located on the left
of the display (Figure 2). The volume may be adjusted up or down
by pressing the volume control
buttons ( + and -).
Battery Replacement
!
NOTE: The remote control is
packed separately in the carton.
1. Slide battery cover open on
the remote control (Figure 3).
2. Correctly install 2 1.5 Volt
(AAA) battery in the battery
holder.
3. Close the battery cover.
Battery must be recycled
or disposed of properly.
Check with your Local
Authority or Retailer for recycling
advice in your area.
Figure 3
Standby
Button
Volume
Controls
Battery
Cover
11
Maintenance
WARNING: Disconnect power
before attempting any maintenance or cleaning to reduce the
risk of re, electric shock or damage to persons.
Glass Cleaning
The glass is cleaned in the factory
during the assembly operation.
During shipment, installation,
handling, etc., the front glass may
collect dust particles, these can
be removed by dusting lightly with
a clean dry cloth.
To remove ngerprints or other
marks, the glass can be cleaned
with a dry cloth. The glass should
be completely dried with a lint
free cloth to prevent water spots.
To prevent scratching, do not use
abrasive cleaners or spray liquids
on the glass surface.
Opti-V Surface Cleaning
To remove ngerprints or other
marks, the exterior nish can be
cleaned with a damp cloth with
a mild detergent. The surface
should be completely dried with
a lint free cloth to prevent water
spots.
Servicing
Except for installation and cleaning described in this manual, an
authorized service representative
should perform any other servicing.
12 www.dimplex.com
Warranty
Two Year Limited Warranty
Products to which this limited warranty
applies
This limited warranty applies to the following models of your newly purchased
Dimplex Opti-V: VF5452L, VF2927L and
VFA2927 and to newly purchased Dimplex
surrounds (mantels) and trims. This limited
warranty applies only to purchases made
in any province of Canada except for
Yukon Territory, Nunavut, or Northwest
Territories or in any of the 50 States of the
USA (and the District of Columbia) except
for Hawaii and Alaska. This limited warranty applies to the original purchaser of
the product only and is not transferable.
Products excluded from this limited warranty
Light bulbs are not covered by this limited
warranty and are the sole responsibility of
the owner/purchaser. Products purchased
in Yukon Territory, Nunavut, Northwest
Territories, Hawaii, or Alaska are not
covered by this limited warranty. Products
purchased in these States, provinces, or
territories are sold AS IS without warranty or condition of any kind (including,
without limitation, any implied warranties
or conditions of merchantability or tness
for a particular purpose) and the entire risk
of as to the quality and performance of the
products is with the purchaser, and in the
event of a defect the purchaser assumes
the entire cost of all necessary servicing
or repair.
What this limited warranty covers and for
how long
Products, other than surrounds (mantels)
and trims, covered by this limited warranty
have been tested and inspected prior to
shipment and, subject to the provisions
of this warranty, Dimplex warrants such
products to be free from defects in material and workmanship for a period of 2
years from the date of the rst purchase of
such products.
Dimplex surrounds (mantels) and trims
covered by this limited warranty have
been tested and inspected prior to shipment and, subject to the provisions of this
warranty, Dimplex warrants such products
to be free from defects in material and
workmanship for a period of 1 year from
the date of rst purchase of such products.
The limited 2 year warranty period for
products other than surrounds (mantels)
and trims and the limited 1 year warranty
period for surrounds (mantels) and trims
also applies to any implied warranties that
may exist under applicable law. Some
jurisdictions do not allow limitations on
how long an implied warranty lasts, so
the above limitation may not apply to the
purchaser.
What this limited warranty does not cover
This limited warranty does not apply to
products that have been repaired (except
by Dimplex or its authorized service
representatives) or otherwise altered. This
limited warranty does further not apply
to defects resulting from misuse, abuse,
accident, neglect, incorrect installation,
improper maintenance or handling, or
operation with an incorrect power source.
What you must do to get service under
this limited warranty
Defects must be brought to the attention of
Dimplex Technical Service by contacting
Dimplex at 1-888-DIMPLEX (1-888-346-
7539), or 1367 Industrial Road, Cambridge Ontario, Canada N3H 4W3. Please
have proof of purchase, catalogue/model
and serial numbers available when calling.
Limited warranty service requires a proof
of purchase of the product.
What Dimplex will do in the event of a
defect
In the event a product or part covered by
this limited warranty is proven to be defective in material or workmanship during (i)
the 2 year limited warranty period for products other than surrounds (mantels) and
trims, and (ii) the 1 year limited warranty
period for surrounds (mantels) and trims,
you have the following rights:
• Dimplex will in its sole discretion either
13
Warranty
repair or replace such defective product or part without charge. If Dimplex
is unable to repair or replace such
product or part, or if repair or replacement is not commercially practicable
or cannot be timely made, Dimplex
may, in lieu of repair or replacement,
choose to refund the purchase price
for such product or part.
• Limited warranty service will be
performed solely by dealers or service
agents of Dimplex authorized to provide limited warranty services.
• For products other than surrounds
(mantels) and trims, this 2 year lim-
ited warranty entitles the purchaser to
on-site or in-home warranty services.
Accordingly, Dimplex will be responsible for all labour and transportation associated with repairing or replacing the
product or part except as follows: (i)
charges which may be levied for travel
costs incurred to travel to the purchaser’s site where the product is located
if the purchaser’s site is beyond 30
miles (48 km) from the closest service
depot of Dimplex’s dealer or service
agent; and (ii) the purchaser is solely
responsible for providing clear access
to all serviceable parts of the product.
• For surrounds (mantels) and trims,
this 1 year limited warranty does
not entitle the purchaser to on-site
or in-house warranty services. The
purchaser is responsible for removal
and transportation of the surrounds
(mantels) and trims (and any repaired
or replacement product or part) to and
from the authorized dealer’s or service
agent’s place of business. On-site
or in-home services for surrounds
(mantels) and trims may be performed
at the purchaser’s specic request
and expense at Dimplex’s then-current
rates for such services. Dimplex
will not be responsible for, and this
limited warranty shall not include, any
expense incurred for installation or
removal of the surrounds (mantels)
or trims or any part thereof (or any
replacement product or part) including,
without limitation, all shipping costs
and transportation costs to and from
the authorized dealer’s or service
agent’s place of business and all
labour costs. Such costs shall be the
purchaser’s responsibility.
What Dimplex and its dealers and service
agents are also not responsible for:
IN NO EVENT WILL DIMPLEX, OR ITS
DIRECTORS, OFFICERS, OR AGENTS,
BE LIABLE TO THE PURCHASER OR
ANY THIRD PARTY, WHETHER IN CON-
TRACT, IN TORT, OR ON ANY OTHER
BASIS, FOR ANY INDIRECT, SPECIAL,
PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST,
OR DAMAGE ARISING OUT OF OR
IN CONNECTION WITH THE SALE,
MAINTENANCE, USE, OR INABILITY TO
USE THE PRODUCT, EVEN IF DIMPLEX
OR ITS DIRECTORS, OFFICERS, OR
AGENTS HAVE BEEN ADVISED OF
THE POSSIBILITY OF SUCH LOSSES,
COSTS OR DAMAGES, OR IF SUCH
LOSSES, COSTS, OR DAMAGES ARE
FORESEEABLE. IN NO EVENT WILL
DIMPLEX, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR
ANY DIRECT LOSSES, COSTS, OR
DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
SOME JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
How State and Provincial law apply
This limited warranty gives you specic
legal rights, and you may also have other
rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale
of Goods shall not apply to this limited
warranty or the sale of products covered
by this limited warranty.
14 www.dimplex.com
Technical Support
Technical and troubleshooting support, as well as a list of replacement parts can be found on
www.dimplex.com/customer_support.
Dimplex North America Limited
1367 Industrial Road
Cambridge ON
Canada N3H 4W3
© 2017 Dimplex North America Limited
15
Loading...