TOLUCA DELUXE
EN
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2
and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
08/53789/0 Issue 1
1
B
820mm
155mm
540mm
2
940mm
600mm
3
A
C
E
D
F
G
H
I
G
4
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
EN
Important Safety Advice
When using electrical appliances, basic
precautions should be followed to
reduce the risk of re, electric shock, and
injury to persons, including the following:
If the appliance is damaged, check
immediately with the supplier before
installation and operation.
Do not use this appliance in the
immediate surroundings of a bath,
shower or swimming pool.
Do not use outdoors.
This appliance must not be located
immediately above or below a fixed
socket outlet or connection box.
WARNING: The appliance carries
the Warning Symbol indicating that
it must not be covered or has a Do
not cover label. Do not cover or
obstruct in any way the heat outlet grille
located above the ame window on the
appliance Overheating will result if the
appliance is accidentally covered. Do
not place material or garments on the
appliance, or obstruct the air circulation
around the appliance, for instance by
curtains or furniture, as this could cause
overheating and a re risk.
In the event of a fault unplug the heater.
Unplug the appliance when not required
for long periods.The supply cord must
be placed on the right hand side of
the heater away from the heat outlet
underneath the appliance.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experinence and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way
and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintaince shall not
be made by Children without supervision.
Children of less than 3 years should
be kept away unless continuously
supervised. Children aged from 3 years
and less than 8 years shall only switch
on/off the appliance provided that it has
been placed or installed in its intended
normal operating position and they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understanding the hazards
involved. Children aged from 3 years
and less than 8 years shall not plug in,
regulate and clean the appliance or
perform user maintaince.
The appliance must be positioned so that
the plug is accessible.
Although this appliance complies with
safety standards, we do not recommend
its use on deep pile carpets or on long
hair type of rugs.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or similarly qualied person in
order to avoid a hazard.
CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal
cut-out, this appliance must not be
supplied through an external switching
device, such as a timer, or connected
to a circuit that is regularly switched on
and off by the utility.
CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given
where children and vulnerable people
are present.
General
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
re to your supplier.
The re incorporates a ame effect, which can be used
with or without heating, so that the comforting effect may
be enjoyed at any time of the year. Using the ame effect
on its own only requires little electricity.
Before connecting the heater check that the supply
voltage is the same as that stated on the heater.
Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which
is related to the operation of the ame effect. This is normal
and should not be a cause for concern.
Electrical Connection
WARNING: THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the
supply voltage.
Before switching on, please read the safety warnings and
operating instructions.
Operating Instructions:
Please see Fig. 3
Icon Display Funtion Description
Press Once to turn the product ‘ON’.
A -
+
B
-
fC
C
D -
Power /
Standby
Flame UpThis Button will increase the brightness of the ame effect. There are 5 brightness settings
Flame
Down
Flame
Cycling
-
- Off
Off
Low
Heat
High
Heat
Cool
Blow
Back
Light
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
‘FLAME EFFECT’ button this turns the ame effect ON or OFF independently of the
products other features.
shown as F1, F2, F3, F4, F5. This button will ONLY increase the brightness level.
This Button will decrease the brightness of the ame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY decrease the brightness level.
This setting is set by pressing the Flame Up button once more after F5. this will cause the
brightness of the ame effect to cycle from F2 to F5 in a continuous Loop.
This will turn the ame effect off. If the heater is ON, the display will activate and remain
active to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/
COOL BLOW.
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display see Fig.1.
When the ame effect is ‘ON’ the display will turn off after 5 seconds, however if the
heater is being used independently of the ame effect. The low heat or high heat icon
will appear continuously in the display.
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’
icon. To Adjust the temperature setting the Temp Down or Temp Up buttons described
below must be used.
(This icon is Orange in Colour)
This icon in the display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH
HEAT’ icon. To Adjust the temperature setting the Temp Down or Temp Up buttons
described below must be used.
(This icon is Red in Colour)
This icon in the display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL
BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower ‘OFF’, no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
Pressing this button will turn ON and OFF the Back Lighting. There are 4 settings, Sides
only, Top only, all OFF and All ON
E -
E -
F
G
G
H -
I -
-
-
Temp
Down
Temp
Up
Sleep
Timer
Volume
down
Volume
Up
Blue-
tooth
LED
COLOUR
Press multiple times to lower the heater temperature in 10C increments. The lowest
temperature that can be set is 180C.
Press multiple times to increase the heater temperature in 10C increments. The highest
temperature that can be set 300C.
When High Heat is selected, the letters ‘HH’ appear in the display, this means the heat
will remain ON continusously and is not controlled by the thermostat.
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5
h r t o 8 . 0 h r b e f o r e t u r n i n g o f f . T h e r e m a i n i n g t i m e o n t h e ‘ S L E E P T I M E R ’ d i s p l a y s .
(This icon is Green in Colour)
Pressing multiple times to control the volume level of the speaker down to mute.
When Bluetooth is not connected, the speaker will play sound of a fire, this can be
turned OFF by pressing this button until the sound is muted.
Controls the level of the speaker Volume up.
The volume buttons can also control the volume of your paired bluetooth device
When a device is paired to the product, pressing this button will disconnect the paired
device.
Press multiple times to change the colour of the LED mood lighting and the coloured
fuel bed. The colour can be set as Orange, Red, Green, Blue, or cycling through all four
colours continuously.
User Modes:
Mode Name /Discription Action (Actions cannot be input by remote control)
Change Celsius (0 C) to Fahrenheit (0 F)
Disable/Enable Heat Options
Press both Temp Up ( ) and Temp Down ( ) on the unit and hold until beep is heard
and display flashes. (To revert back to Celsius repeat this action)
Hold both Back Light ( ) and Temp Down ( ), on the unit, for 2 seconds, when the
heater has been disabled the display will read “--” and beep. To enble heat repeat this
action.
Remote Control - See Fig. 3
maximum range of use is ~ 5metres.
NOTE: It takes time for the receiver to respond to the transmitter.
NOTE: The reciever for the remote control is located in the
display, aim the remote control in this direction when inputting
commands.
Do not press the buttons more than once within two seconds
for correct operation.
Battery Information - See Fig. 3
1. To activate the remote control remove the clear battery
isolation strip at the base of the remote control, which is used
to ensure your remote control reaches you fully charged.
2. To replace the remote control battery, turn over the remote
control, and follow the diagram embossed on the remote
control
3. Only use CR2025 or CR2032 size of batteries.
Installation
WARNING: FALLING OR TIPPING APPLIANCES CAN
CAUSE INJURY OR DEATH OF YOUNG CHILDREN, PLEASE
ENSURE CHILDREN DO NOT CLIMB, HANG OR STAND ON
THIS PRODUCT.
WARNING: THE APPLIANCE IS PROVIDED WITH A WALL
FIXING KIT, THIS KIT IS DESIGNED TO HOLD THE PRODUCTS
WEIGHT, IT IS NOT A SUBSTITUTE FOR PROPER ADULT
SUPERVISION. DO NOT ALLOW CHILDREN TO CLIMB OR HANG
ON THIS PRODUCT.
Safety Message - Sufcient expertise is required for installing
this product. If unsure we recommend that you use an
installer and pay special attention to safety during the
installation.
Wireless Speaker Control.
The unit needs to be in standby for the speaker function to
operate, you do not need the ame effect to be operating.
The speaker can be used in 2 ways. You can pair a suitable
device to the speaker wirelessly and listen to music, audio
books or casts from a suitable device, or when the ame
effect is operating the soothing crackling sound of a log re
can be played for ambient sound effect.
To listen to the crackling log effect, just press the volume up
button on your remote control until you reach a vlolume
level which is comfortable for you, to lower the volume press
the volume down button. The crackling is turned OFF by
pressing the volume down button until the sound is muted.
To use the speaker to listen to your own material the speaker
must rst be paired to a compatible device. To pair with the
unit:
1. Ensure the unit is plugged in and switched on at the mains
socket.
2. Using a compatible device search for “DImplex Fire”,
select and pair your device to “DImplex Fire”.
3. Once connection is made between your device and the
unit an electronic tone will sound to alert you the pairing
was successful.
With the unit now paired you can control the speaker
volume using the volume buttons on the remote control
handset or your device’s volume controls.
Note: If you experience problems pairing to the speaker,
you may need to re-pair to the speaker, follow these steps:
1. On your device go to the Bluetooth Settings.
2. Select the “Dimplex Fire” and press “Forget” to disconnect
from the speaker.
3. Turn Bluetooth OFF, and then ON. Your device should now
rediscover “Dimplex Fire” again.
4. Select “Dimplex Fire” to pair with the speaker.
Wall Installation- See Fig. 2
Do not connect appliance until properly xed to the wall
and the Instruction leaet is fully read. In particular, the
minimum distances must be observed.
The wall plugs supplied with this product are for use with
Block/Brick built walls only.
This model is designed to be permanently xed to a wall
at a minimum height of 300mm. The wall bracket must be
tted horizontally and the cable routed to the bottom right
of the appliance.
A height of 600 to 725mm from bottom of the appliance
to oor is recommended for optimum viewing of fuel bed.
For optimum viewing, mark the top three screw xing
positions on the wall in accordance with the recommended
xing dimensions - see Fig. 2. Drill holes with a 6mm drill bit.
Fix the wall bracket using the plugs and screws provided.
Carefully lift the appliance up ensuring that the appliance
engages with the wall bracket correctly.
A bottom xing bracket is supplied with the unit, xed to
the base of the appliance. Remove the screw and the
bracket, turn the bracket through 180 degrees so it is now
facing downward and re t using the screw just removed.
With the bracket in place mark the location of the hole on
the wall. Remove the appliance,drill the wall, t the wall
plug and re-t the appliance ensuring that you secure it in
place by screwing the bottom xing bracket to the wall.
Fuel Bed Media
Acrylic Ice Crystals and White Pebbles are supplied in the
box with your re. allowing you the option of which to place
on your re. To Fit the Acrylic Ice Crystals, place the small
Crystals on the fuel bed tray, then place the larger crystals
on top of the small pieces. Arrange the larger pieces to your
liking. A suggestion is to place one large crystal centrally on
the fuel bed and the other four positioned symmetrically
around this piece.
The White pebbles are placed on the fuel bed tray until the
tray is completely covered by pebbles to your liking.
Fitting the Front Glass- See Fig. 5
Your new re is supplied with the front glass not secured to
the engine, this is to keep the glass safe in transit. To t the
glass to your re, simply insert the four hangers on the back
of the glass through the slots provided on the chassis. The
hangers go in through the slots and then move down to
hold the glass in place. The glass can then be secured in
place by inserting the small black screw provided through
the hole in any one of the hangers into the side of the unit.
Thermal Safety Cut-out
The built-in overheat cut-out switches the appliance off
automatically in the event of a fault. If this occurs switch off
the appliance or disconnect the mains plug from the socket.
After a short cooling down phase, the appliance is ready for
use again. If the fault should occur again, see your local dealer.
Light Emitting Diode
This re is tted with LED (Light Emitting Diode) bulbs in place
of traditional incandescent bulbs. These generate the same
light levels as traditional bulbs, but use a fraction of the energy
consumed.These bulbs cannot be replaced.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or uff the soft brush
attachment of a vacuum cleaner should occasionally be
used to clean the outlet grille of the fan heater.
WARNING: do not operate the product without the grille
and outer glass in position as this may effect the operation
of the heater.
Recycling
For electrical products sold within the
European Community. At the end of the
electrical products useful life it should not
be disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice in your country.
Servicing
Except for installation and cleaning described in this
manual, an authorized service representative should
perform any other servicing.
.
Loading...