Dimplex TIMRA TMR15 Installation And Operating Manual

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
TIMRA TMR15
08/19430/1 - Issue 1
1
2
3
4
5
‘a’
579
215
C
B
225
575
444
414
397
557
A
‘x’
‘z’
‘x’
‘y’
‘a’
‘b’
420mm
565mm
250mm
6
7
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the following:
If the appliance is damaged, check with the supplier before installation and operation.
Do not use this heater in the immediate surroundings of a bath, shower or swimming pool.
Do not locate the heater immediately below a fixed socket outlet or connection box.
Do not cover or obstruct in any way the heat outlet grille located at the top of the heater or the heat outlet at the base of the heater. Overheating will result if the heater is accidentally covered.
This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre from the heater.
Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs.
The appliance must be positioned so that the plug is accessible.
Do not use this heater in series with a thermal control, a program controller, a timer or any other device that switches on the heat automatically, since a fire risk exists when the heater is accidentally covered or displaced.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard.
General
Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier. Loose pebbles, a flat fuel bed, a remote control and batteries are packed separately within the carton.
The fire is supplied fitted with a ‘log fuel effect’. To change from the ‘log fuel effect’ to ‘pebbles fuel effect’ see ‘Lamp/Fuel effect Replacement’.
This fire incorporates a flame effect which can be used with or without heating, so that comforting effect may be enjoyed at any time of the year. The flame effect is provided by a low wattage motor and two 60 watt lamps. Using the flame effect on its own, therefore, requires little electricity.
The controls are located at the bottom right hand corner of the appliance (see ‘x’ in Fig. 1). A choice of 750W or 1500W heat output is provided by the fan heater, which is concealed at the top of the heater behind the removable front panel.
The fire is designed to be fitted into a large fireplace opening or a purpose built structure - see Fig. 2 for recommended sizes for opening.
Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is related to the operation of the flame effect. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating instructions.
Installation
The fire is designed to be fitted into a large fireplace opening or a purpose built structure - see Fig. 2 for recommended sizes of opening. The installation of a purpose built structure should be carried out by a competent person. If in doubt please consult your local builder.
Seal all draughts and vents to prevent chimney debris from falling onto the Fireplace Insert. Do not install into an existing fireplace that is prone to dampness.
At the base of the fire, four adjustable feet (see ‘A’ in Fig. 1) are provided for levelling the fire where the base of the fireplace opening is raised above the level of the hearth.
Adjust by turning the feet until the desired height has been reached.
Operation
The controls are located at the bottom right hand corner of the
appliance - see ‘x’ in Fig. 1.
Connect the fire to your electricity supply. Note: When either the remote control or the manual controls are
used the neon’s will come on for 3 seconds indicating the appropriate setting - see Fig. 3.
Manual Operation
Note: The Standby Switch (see ‘a’ in Fig. 5) must be first turned
on to operate either the manual or the remote controls. The red indicator mark on the switch will be visible when it is turned on.
Setting Operation Indication
Flame effect Press the ‘I’ button once Left Neon Flame effect & 750W heat setting Press the ‘I’ button again Left & Middle Neon
Flame effect & 1500W heat setting Press the ‘I’ button again All 3 neon’s
To turn off any of the settings press the ‘O’ button once.
To increase or decrease the brightness of the fuel effect use the buttons ‘
’ as shown in Fig. 5.
Initializing the Remote Control
Note: The remote control is packed separately in the carton.
1. Slide open the battery cover on the back of the remote transmitter.
2. Install the AAA batteries into the remote control (see Fig. 4).
3. Replace battery cover.
Dispose of batteries in the proper manner according to Provincial and local regulations. Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are not replaced at the same time, if disposed of in a fire or if an attempt is made to charge a battery not intended to be recharged
.
Remote Control Operation
Warning: It takes some time for the receiver to respond to the
transmitter. Do not press the buttons more than once within two seconds for correct operation.
Setting Operation Indication
Flame effect Press the ‘I’ button once Left Neon Flame effect & 750W heat setting Press the ‘I’ button again Left & Middle Neon Flame effect & 1500W heat setting Press the ‘I’ button again All 3 neon’s
To turn off any of the settings press the ‘O’ button once.
To increase or decrease the brightness of the fuel effect use the buttons ‘ ’ as shown in Fig. 4.
Front Panel removal and refit
To gain access to the lamps or to change the fuel effect you must first remove the Front Panel. Remove the front panel (see ‘x’ in
Fig. 6) by lifting up then out and carefully leave to one side.
To refit the front panel follow steps below:
1. Tilt the Front Panel at a slight angle, insert the top two latches (see ‘a’ in Fig. 6) into the top two slots (see ‘b’ in Fig. 6).
2. Insert the bottom two latches into slots.
3. Drop the Front Panel ‘x’ down until it slots into position, ensuring it is securely held in place.
Lamp/Fuel Effect Replacement
To gain access to the lamps
1. Remove the
Front Panel (see ‘x’ in Fig. 6) by lifting up
then out and carefully leave to one side.
2. Remove the three screws (see ‘y’ in Fig. 6) on the fuel
effect.
3. Slide the fuel effect out, by holding the front ledge and set
aside carefully (taking care not to damage the logs as they are fragile) – see Fig. 6.
4. For access to the bulbs, carefully rotate the flexible
rotisserie out of position ensuring that the rubber grommet is not lost – see Fig. 7.
5. Unscrew the defective lamp anti-clockwise. Replace with
a 230V, 60W E14 SES lamp, do not over tighten (see Fig. 7).
6. Refit the fuel effect (with three screws) and Front Panel.
To replace ‘log fuel effect’ with ‘pebbles fuel effect’
1. Remove the
Front Panel (see ‘x’ in Fig. 6) by lifting up
then out and carefully leave to one side.
2. Remove the three screws (see ‘y’ in Fig. 6) on the fuel
effect.
3. Slide the ‘log fuel effect’ out, by holding the front ledge and
set aside carefully (taking care not to damage the logs as they are fragile and retain for possible future use) – see Fig. 6.
4. Fit the new flat bed fuel effect (‘pebbles fuel effect’) by
sliding it in from the front, ensuring the bracket at rear (see ‘z’ in Fig. 6) slots under the inner glass panel.
5. Screw fix the flat fuel bed in position using the three screws
6. When flat fuel bed is in position, place the pebbles carefully
on top.
7. Refit Front Panel (see ‘x’ in Fig. 6)
Thermal Safety Cut-out
For your safety, this appliance has been fitted with thermal cut­out. In the event that the product overheats, the cut-out switches the heat off automatically.
To bring the heat back into operation, remove the cause of the overheating, then unplug or turn off the electrical supply to the heater for up to 10 minutes.
When the heater has cooled sufficiently, re-connect and switch on the heater.
Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility
Cleaning and Maintenance
Warning: Always disconnect from the power supply before attempting any maintenance.
Cleaning
Before commencing cleaning, unplug the heater and allow it to cool.
The surface of the heater should be given an occasional wipe over with a soft damp cloth. Do not use detergents abrasive cleaning powder or polish on the body of the heater. The glass screen should be cleaned carefully with a chamois leather. Do not use proprietary glass cleaners.
After Sales Service
Your product is guaranteed for one year from the date of purchase. Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it has been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer services help desk on 0870 727 0101. It would assist us if you can quote the model number, series, date of purchase, and nature of the fault at the time of your call. The customer services help desk will also be able to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
Glen Dimplex UK Limited Millbrook House Grange Drive Hedge End Southampton Hampshire. SO30 2DF
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services: Tel. 0870 7270101
Fax. 0870 7270102 e-mail customer.services@glendimplex.com
Republic of Ireland Tel. 01 8424833
[c] Glen Dimplex UK Limited All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
Loading...