The product complies with the European Safety Standards EN60335-2-30 and the European S tandard Electromagnetic Compatibility
(EMC)EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2006/108/EC
08/19075/2 (UK) Issue 3
T ANGO
CASPER
(TNG20) (CAS20/CAS20N)
1
571
440
305
571
440 295
TANGO (TNG20) CASPER (CAS20/CAS20N)
1
2
3
I
II
II
2
5
4
3
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your supplier.
These models are designed to be free standing and are normally
positioned against a wall.
The fire incorporates a flame effect, which can be used with or without
heati
ng, so that the comforting effect may be enjoyed at any time of
the year. Using the flame effect on its own only requires little electricity .
A choice of 1kW or 2kW heat output is provided by the fan heater,
which is located at the bottom of the unit.
Before connecting the heater check that the supply voltage is the
same as that stated on the heater.
On the Springborne model loose coals are packed separately within
the carton. When the heater is assembled the coals can be placed
on top of the fuel bed, as required.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for
concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Controls - see Fig. 2
The heater controls are located on the right hand side of the heater
- see Fig. 1. Three switches provide a choice of heat settings. A
switch is in the ON position when the side with the markings on
(i.e. I, I, or II) is pushed in.
Switch 1 (I) Controls the electricity supply to the
heater and flame effect. Note: This switch
must be in the ON (I) position for heater to operate
with or without heat.
Switch 2 (I) Provides 1kW heat out put
Switch 3 (II) Provides 2kW output with switch 2
Lamp Replacement - see Fig. 3, Fig. 4 and Fig. 5
The lamps are located behind the back panel. To gain access to the
lamps, the screws indicated in Fig. 3 which secure the back panel,
must be removed.
Remove and slide out panel as indicated on Fig. 4.
Remove the defective lamp by unscrewing it as shown in Fig. 5.
Replace with a 60W E14 SES Clear candle lamp. Take care not to
over-tighten the lamp.
Refit the back panel and secure with the screws.
Thermal Safety Cut-out
The built-in overheat cut-out switches off the appliance automatically
in the event of a fault. Switch off the appliance or disconnect the
mains plug from the socket. After a short cooling down phase, the
appliance is ready for use again. If the fault should occur again, see
your local dealer.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Cleaning
WARNING – AL W A YS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully with
a soft cloth. DO NOT use proprietary glass cleaners.
T o remove any accumulation of dust or fluf f the soft brush attachment
of a vacuum cleaner should occasionally be used to clean the outlet
grille of the fan heater.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electrical shock and injury to persons, including the
following:
If the appliance is damaged, check with the supplier
before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath,
shower or swimming pool.
Do not locate the appliance immediately below a fixed
socket outlet or connection box.
This appliance can be used by children aged form 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by Children without
supervision.
Children of less than 3 years should be kept away
unless continuously supervised. Children aged from 3
years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed
in its intended normal operating position and they have
been given supervision or instruction concerning use
of the appliance in a safe way and understanding the
hazards involved. Children aged from 3 years and less
than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
Do not use this appliance in series with a thermal
control, a program controller, a timer or any other
device that switches on the heat automatically, since a
fire risk exists when the appliance is accidentally
covered or displaced.
This appliance is not equipped with a device to control
the room temperature. Do not use this appliance in
small rooms when they are occupied by persons not
capable of leaving the room on their own, unless
constant supervision is provided.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from
the appliance.
In the event of a fault unplug the appliance.
Unplug the appliance when not required for long
periods.
Although this appliance complies with safety
standards, we do not recommend its use on deep pile
carpets or on long hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by
the manufacturer or service agent or a similarly
qualified person in order to avoid a hazard.
Keep the supply cord away from the front of the
appliance.
Warning: In order to avoid overheating, do not cover
the appliance. Do not place material or garments on
the appliance, or obstruct the air circulation around
the appliance, for instance by curtains or furniture, as
this could cause overheating and a fire risk.
Warning: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must
not be supplied through an external switching device,
such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
CAUTION - Some parts of this product can become
very hot and cause burns. Particular attention has to
be given where children and vulnerable people are
present.
This instruction can be found at WWW.DIMPLEX.CO.UK
- T ANGO (TNG20)
- CASPER (CAS20 / CAS20N)
UK
DIMPLEX
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
TEL: 0844 879 3585
FAX: 0844 879 3582
WEBSITE: www.dimplex.co.uk
Republic of Ireland Tel. 01 8424833
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex.
A division of GDC Group Ltd,
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it
has been installed and operated in accordance with these
instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance with this
product please go to www.dimplex.co.uk where you will find
our self help guide by clicking on “After Sales” or ring our helpdesk
on 0844 879 3585 (UK) or 01 842 4833 (R.O.I.) .
Spare parts are also available on the website
www.dimplex.co.uk
Please retain your receipt as proof of purchase.
- T ANGO (TNG20)
- CASPER (CAS20)
UK
Loading...