Dimplex SP820, SP8 Installation And Operating Instructions Manual

Download

Page 1

ntrol

min

ixed

socket

min

FRONT

SIDE

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.

Dimensions

(millimetres)

Installation and Operating Instructions

Electrical

08/19116/0 Issue 0

Fig. 1

Important Safety Advice:

When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• If the appliance is damaged, check immediately with the supplier before installation and operation.

• Do not use this heater in the immediate surroundings of a bath, shower or swimming pool.

• Do not use outdoors.

• This heater must not be located immediately

above or below a fixed socket outlet or connection box.

• Do not cover or obstruct in any way the heat outlet grille located underneath the heater. Overheating will result if the heater is accidentally covered.

• In the event of a fault unplug the heater.

• Unplug the heater when not required for long

periods.

• The supply cord must be placed on the right hand side of the heater away from the heat outlet underneath the heater.

• Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs.

• This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.

• The appliance must be positioned so that the plug is accessible.

• If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly qualified person in order to avoid a hazard.

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage. Do not switch the appliance on until properly installed. Please read all the safety warnings and operating instructions.

Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier.

Contents of Carton.

• SP8 Heater.

• Wall fixing bracket.

• Three fixing screws and three wall plugs.

• Remote control and batteries ( 3 AAA’s type).

• Spare bulb.

Do not connect the heater to an electricity supply until it is installed on a wall correctly. - see ‘Installation’. A choice of 1kW or 2kW heat output is provided by the fan heater, which is concealed underneath the unit. The heater can be used remotely or manually. - see ‘Operation’. General features of remote control are:

• Heat output can be increased or decreased

according to your particular requirements.

• The illumination of fuel effect can be increased or

decreased.

• Programmable timer.

Please note: Used in an environment where background noise is very low, it may be possible to hear the fan which operates the flame effect. This is normal and should not be a cause for concern.

General

Wall Fire SP8 Model No: SP820

Page 2

Installation

Recommended Fixing Dimensions - Fig. 2

Fig. 3

Fig. 4

Fig. 5

Mark the bottom hole position (see Fig. 5), remove the heater ensuring that the bottom fixing bracket is rotated up.

Drill and fit wall plug.

Refit the heater to the wall fixing bracket (i.e. follow steps as in Fig. 4 a,b,c and d above) and rotate the bottom fixing bracket down again and use the screw provided to permanently fix the heater in place.

The heater should not be connected until the instruction leaflet is read fully.

Do not connect appliance until properly fixed to the wall and the Instruction leaflet is read fully.

This model is designed to be permanently fixed to a wall at a minimum height of 300mm.

The wall bracket must be fitted horizontally and the cable routed to the bottom right of the heater as in Fig 1.

A height of 600mm from bottom of heater to floor is recommended for optimum viewing of fuel bed (see Fig. 2 for recommended fixing dimensions).

For optimum viewing mark the top two screw fixing positions on wall in accordance with the recommended fixing dimensions - see Fig. 2.

Fix the wall bracket using the two plugs and screws provided

- see Fig 3.

Carefully lift the heater up ensuring that the top rear ledge of heater engages the wall bracket and is sitting centrally positioned. - see Fig 4 (b).

Rotate the bottom fixing bracket down. - see Fig 4 (c).

Gently bring the heater level with the wall. - see Fig 4 (d).

mark hole centre with pencil

outline of wall fire

Page 3

Manual Operation

The Standby Switch (Switch 1) must be first turned ‘ON’ and the AUTO/MAN (Switch 2) switch set to ‘MANUAL’ to operate the manual controls - see Fig 6.

Note : When the fire is put in Manual mode the first time the flame effect will come on indicated by the Bottom neon coming on for 3 seconds - see Fig 7.

Setting Operation Indication

Flame Effect Bottom Neon

Flame Effect & 1Kw Heat Press the ‘ I ’ button (Switch 3) Middle Neon

Flame Effect & 2Kw Heat Press the ‘ I ’ button again (Switch 3) Top Neon

To go to the previous settings press the ‘ O ‘ button (Switch

3).

To increase or decrease the brightness of the flames, use the dimmer button (Switch 4). You can have any setting between full brightness and the flames totally off. The heat setting will remain the same.

To turn off the power the Standby Switch (Switch 1) must be turned ‘OFF’.

Note : Every time that manual mode is selected the previous light and heat settings come on automatically.

Fig. 6

Fig. 7

Manual Controls

Page 4

Remote Control Operation

LCD display

The LCD display shows the following functions:

• Main menu points: OFF, FLAME, HEAT, TEMP, TIMER, PROG, and TIME.

• Brightness of the flame effect shown as a bar chart in 4 steps (50 steps internally).

• Remote control set temperature in °C (thermostat function).

• Room temperature in °C .

• Selectable heat settings LOW HEAT, HIGH HEAT.

• Time display in format hh:mm – shown as 24hr.

• Weekdays MON, TUE, WED, THU, FRI, SAT, SUN.

Menu functions

• OFF switching off of all functions (stand-by mode).

• FLAME switching on the flame effect from 0 (off) to

50 (max. brightness).

• HEAT setting the desired heat position from 0 (off) to 2 (max. heat setting).

• TEMP preselection of the remote control set temperature from 5°C to 35°C.

• TIMER selection of the run back timer function (from 1 minute to 4 hours 59 minutes). When the selected time is over the unit will be in stand-by mode.

• PROG selection of the programming mode. 32 individual programs can be entered. This is a week timer where all functions of the unit can be checked time controlled.

• TIME setting the time and the weekdays.

First steps

• Fit batteries supplied.

• Press switch 1 to ON (see Fig. 6).

• Press switch 2 to AUTO (see Fig. 6)

The remote control is now ready.

General

The remote control consists of 5 control buttons and a LCD display with a visible area of 40x40mm.

The maximum range of use for the remote control is 15metres.

LCD Display Fig. 8

Operating Instructions

• Switching ON/OFF The heater can be switched on by pressing the enter  or   buttons. The heater can be switched off by moving the cursor to the OFF menu item.

• Flame brightness

Navigate the cursor to FLAME with the   buttons. Press  - to change the brightness of the fire effect from off (0) to maximum (50).

• Heat settings

Navigate the cursor to HEAT with the   buttons. Press 

- to change the heat setting between off/low heat/maximum heat.

Note: If the room temperature

is higher than the remote control set temperature located on the left side of LCD display, heat will not come on (see Thermostat operation below).

• Thermostat

Navigate the cursor to TEMP with the   buttons. Press 

- to set the desired remote control set temperature between 5°C and 35°C and press enter . When the room temperature is higher than the remote control set temperature, the heater switches off automatically until the room temperature falls below the remote control set temperature.

• Runback timer

Navigate the cursor to TIMER with the   buttons. Set the hours (0 to 4) with

 - and press enter . Then set the

minutes (0 to 59) with  - and press enter . Now the runback timer is activated (the symbol TIMER appears) and will switch the heater off automatically when the pre-set time is over.

• Time setting

Navigate the cursor to TIME with the   buttons. Press the enter button  to adjust the weekday with the

 - buttons.

Confirm with the enter button  and set the hours and minutes with  -. Press enter  or  to leave the time menu.

• Program mode

1. Navigate the cursor to PROG with the

 , buttons and

press enter . Choose a program number between 1 and 32 with the  - buttons and press enter .

2. Set the days with

 - . Single days, Monday until Friday,

Saturday and Sunday or Monday until Sunday can be chosen. Press the enter button  to accept.

3. Set the program start time with  - and confirm the

hours and minutes with the enter button .

4. Set the program stop time with  - and confirm the

hours and minutes with the enter button .

5. Set the remote control set temperature with  - and

confirm with the enter button .

6. Set the brightness of the fire effect with  - from 0 to

50 and confirm with the enter button .

7. Set the heat setting between off/low heat/maximum heat

with the  - button and confirm with the enter button .

8. All settings for the first program are done now. Enter a

new program according to the steps 1-8 or activate the already entered program by leaving of this menu with the  button.

9. Now the program mode is active, the symbol PROG

appears. The heater operates according to the entered information. While the program mode is activated, the start and stop time, the active program number and the remote control set temperature and the room temperature

will be displayed alternating.

Page 5

Replacing the remote control

The new remote control must be set up as follows:

Press switch 1 to ON . Press switch 2 to AUTO (see Fig. 6). Press switch 3 to O for more than 3 seconds until all three LED’s are on (see Fig. 7). Press the remote control’s enter button or the   buttons.

Now the heater has learned the serial number from the remote control and will work with this remote control only (this procedure is repeatable many times).

General information

1. In case that the remote control is out of order or the batteries need replacing the fire will stop automatically after 3 minutes.

2. If the batteries are changed the programme memory remains but the time has to be set (see Time setting).

Important Battery information.

Discard leaky batteries. Dispose of batteries in the proper manner according to Provincial and local regulations. Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are not replaced at the same time, if disposed of in a fire or if an attempt is made to charge a battery not intended to be recharged.

Page 6

The front window assembly will need to be removed in order to change lamps.

Warning! The front window assembly is heavy and easily damaged !.

The front window assembly is fixed with two screws on top and is supported underneath by the chassis. Care is needed to avoid the assembly falling forward while removing the screws see Fig. 9.

To gain access to lamps please apply the following procedure :

Remove the two screws which hold the front window assembly in place.

While holding the assembly by its sides with both hands, carefully tilt forwards and then lift up and out - see Fig. 9.

Place the front window assembly flat on a protective surface such as a matt with the glass facing away from the floor.

Remove two screws securing fuel effect. Holding the logs carefully lift up (1) and out (2) - see Fig. 10.

Carefully slide the flexible rotisserie to one side ensuring that the rubber grommet is not lost – see Fig. 11.

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS.

Lamp Replacement

Fig. 9

Fig. 10

Fig. 11

Page 7

Remove the defective lamp by unscrewing it (see Fig. 12). Replace with a 60W E14 SES Clear Candle bulb, rotating it.

Take care not to over-tighten the lamp.

Steps for reassembling the heater

1. Refit the rotisserie making sure that the rubber

grommet is carefully pushed into the slotted hole on the axial bracket (see Fig. 11).

2. Refit the fuel effect ensuring that the fuel effect bracket on the fuel effect slots in between the fuel effect retaining bracket and the inner glass (see Fig. 10).

3. Refit the the window assembly (ensuring that its base is held in place i.e. that it slots into the channel on the frame (see Fig. 10) reversing the steps as outlined previously.

Fig. 12

Page 8

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free of charge (excluding lamps & subject to availability) provided it has been installed and operated in accordance with these instructions.

Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this guarantee.

Should you require after sales service you should contact our customer services help desk on 0870 727 0101. It would assist us if you can quote the model number, series, date of purchase, and nature of the fault at the time of your call. The customer services help desk will also be able to advise you should you need to purchase any spares.

Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service.

Please retain your receipt as proof of purchase.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners.

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

Glen Dimplex UK Limited Millbrook House Grange Drive Hedge End Southampton Hampshire. SO30 2DF

UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)

Customer Services: Tel. 0870 7270101

Fax. 0870 7270102 e-mail customer.services@glendimplex.com

Republic of Ireland Tel. 01 8424833

[c] Glen Dimplex UK Limited