Dimplex SF55992-AU Parts And Service Manual
26” FIREPLACE
MODEL NUMBER
SF55992-AU
PARTS AND SERVICE MANUAL
TABLE OF CONTENTS
OPERATION PAGE 1
PARTS DRAWING PAGE 3
PARTS LIST PAGE 4
WIRING SCHEMATIC PAGE 6
LIGHT BULB REPLACEMENT PAGE 10
MAIN POWER ON/OFF SWITCH REPLACEMENT PAGE 12
LIGHT DIMMER SWITCH REPLACEMENT PAGE 13
FLAME SPEED CONTROL REPLACEMENT PAGE 14
FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 15
HEATER ON/OFF SWITCH REPLACEMENT PAGE 16
HEATER THERMOSTAT CONTROL REPLACEMENT PAGE 17
HEATER ASSEMBLY REPLACEMENT PAGE 18
POWER CORD REPLACEMENT PAGE 19
D
E A C
OPERATION
This section will explain the function of each convenient control.
To access the controls, open the upper grill by pulling, near the top right hand side,
forward and down.
A. MAIN ON/OFF SWITCH
The ON/OFF SWITCH supplies power to all fireplace functions (Heater/Flame).
B. FLAME ACTION CONTROL
Turn the flame action control knob to adjust the flame speed to the desired level.
C. FLAME BRIGHTNESS CONTROL
Turn the flame brightness control knob to increase or decrease the brightness of the
flame and embers.
D. LED INDICATORS
Indicates the current function of the fireplace.
E. MANUAL SELECTION SWITCH
To choose between flame effect setting, flame effect with low heat setting, and flame
effect with high heat setting.
F. HEATER THERMOSTAT CONTROL
To adjust the temperature to your individual requirements, turn the thermostat control
clockwise all the way to turn on the heater. When the room reached the desired
temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in
this position to maintain the room temperature at this setting. For additional heat, turn
clockwise until you hear the click again and the heater will turn on.
NOTE:
The heater may emit a slight, harmless odor when first used. This odor is a normal
condition caused by initial heating of internal heater parts and will not occur again.
RESETTING THE TEMPERATURE CUTOFF SWITCH
This unit is equipped with a thermostat which controls the temperature of the room. It
does this by turning the heater on and off. The heater is protected with a safety device
to prevent overheating. Should the heater overheat, an automatic cut out will turn the
heater off and it will not come back on without being reset. It can be reset by switching
the main ON/OFF SWITCH to OFF and waiting 5 minutes before switching the unit back
on.
CAUTION
If you need to continuously reset the heater, unplug the unit and call your local dealer.
F
B
1
Level 1 Indicator
Level 2 Indicator
Level 3 Indicator
REMOTE CONTROL USAGE
The fireplace is supplied with a radio frequency remote control. This remote control has
a range of approximately 50 feet. (15.25m), it does not have to be pointed at the
fireplace and can pass through most obstacles (including walls).
Remote Control Initialization
This procedure is required every time there is a loss of
power to the remote control in the fireplace. (i.e. power
failure, breaker tripped, main power switch is turned off)
1. Ensure that power is supplied through main
service panel.
2. Locate manual controls (refer to OPERATION
section).
3. Activate main power switch, red indicator lights will
flash momentarily.
4. Press ON button located on the remote control
transmitter (FIGURE 1). This will synchronize the
remote control transmitter and receiver.
Remote Control Usage
The remote control operates the fireplace levels
sequentially. The level is increased every time the ON
button on the transmitter is pressed. The fireplace can
be turned off at any point by pressing the OFF button
FIGURE 1
on the remote control transmitter.
Level 1: The flame effect is turned on and the first red
indicator light flashes momentarily.
Level 2: The flame effect remains on, the heater is
activated to the low heat setting, and the first and
second red indicator lights flash momentarily.
Level 3: The flame effect remains on, the heater is set
to the high heat setting, and all three red indicators
flash momentarily.
MANUAL SELECTION SWITCH
Operates fireplace in the same matter as the remote
control transmitter. Pressing the right side of this switch
has the same effect as the button on the
remote control and the right side has the same effect as
the button of the remote control. Pressing once to
the left activates Level 1, twice activates Level 2, three
times activates Level 3. Pressing to the left side turns
the fireplace off.
2
SF55992-AU
5
16
4
7
8
10
11
2
15
6
14
9
13
3
12
10
1
18
17
3
SF55992-AU
FIREBOX, REG DLX SYMPHONY
CATALOGUE NO. SF55992-AU
PART NO. 6900420859
MOD.LEVEL NONE
REPLACEMENT PART REPLACEMENT PART NO.
1. LOG SET 0437960100RP
2. PROJECTION SCREEN 0437970100RP
3. FLICKER MOTOR 3000240200RP
4. HEATER ASSEMBLY 2200550100RP
5. THERMOSTAT 2300150100RP*
6. MAIN ON/OFF SWITCH 2800070100RP
7. FLAME SPEED CONTROL 3000410100RP
8. LIGHT DIMMER 3000420100RP
9. CORD SET 4100080159RP
10. LAMPHOLDER UPPER/LOWER 4200050100RP
11. MIRROR 5900060300RP
12. REFLECTOR ASSEMBLY 5900070100RP
13. FRONT GLASS 5900000100RP
14. DIMMER LIGHT CONTROL KNOB 8800000100RP
15. FLAME SPEED CONTROL KNOB 8800000200RP
16. THERMOSTAT CONTROL KNOB 8800000300RP
17. FOOT FIREPLACE 8800090100RP
18. REMOTE TRANSMITTER 3000530300RP
18.REMOTE RECIEVER BOARD 3000550100RP
18.SWITCH BOARD 3000530200RP
REPLACEMENT PARTS
4
Loading...