Dimplex QM050RF, QM070RF, QM100RF, QM125RF, QM150RF Operating Manual

OPERATING MANUAL

Quantum Series Heater

Models: QM050RF / QM070RF / QM100RF

QM125RF / QM150RF

- 1 -

08/82862/0 ISSUE: 2 Series: G.6

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE. Note also the information presented on the appliance

Warnings in this document are identified by a warning triangle against a
grey backgound.
Keywords at the start of a warning indicate the type and seriousness of
the ensuing risk if measures to prevent the risk are not taken.

The following keywords are defined and can be used in this document:

○ DANGER indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

○ WARNING indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

○ CAUTION indicates a hazardous situation which, if not avoided, could result in

minor to moderate injury.

○ NOTICE is used to address practices not related to personal injury.

CAUTION

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR
DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

IMPORTANT SAFETY ADVICE

When using electrical heaters, basic precautions should always be followed to reduce
the risk of fire, electrical shock, and injury to persons, including the following:

IMPORTANT – The wall bracket supplied with the heater must be used.
IMPORTANT – All packaging should be disposed of in an appropriate manner.

OVERHEATING WARNING

WARNING - In order to avoid overheating, do not cover or obstruct the heater. Do

not place material or garments on the heater, or obstruct the air circulation around the
heater, for instance by curtains or furniture, as this could cause overheating and a fire
risk. NEVER cover or obstruct in any way the heat outlet slots at the top of the heater
or the air outlet slots in the base of the heater.

WARNING - THE SURFACES ON THIS HEATER CAN BE HOT.

The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of fire
that exists if the heater is accidentally covered.

CAUTION - Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are present.

For your safety this heater is fitted with a thermal cut-out. In the event that the product
overheats for some reason, the cut-out prevents excessive temperatures on the
product by cutting the power to the heater. Once the heater has cooled down, it will
reset automatically, it will continue to cycle on and o automatically until the reason for
overheating is removed.

The display screen may flash red to indicate the product has overheated. To reset the
display, remove the obstruction and hold Enter for 10 seconds.

- 2 -

SUITABLE APPLICATIONS

WARNING - This heater is suitable for normal dwelling purposes and should not be

used in any other type of environment. This product should only be used in the country
where it was purchased from by a recognised commercial retailer. Do not use outdoors.

SERVICING AND REPAIRS

WARNING - Servicing and product repairs should only be undertaken by the

manufacturers approved service agent or a similarly trained or qualified person, using
only exact manufacturer approved spare parts.
PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with
the convection eect of electric heaters can cause significant soot deposits to build
up on the surface directly above and to the sides of the heater. This is not a fault of the
heater. Extensive burning of candles or smoking in the operating environment of this
product can produce heavy discolouration within a few months of use.

OPERATING WARNINGS

IMPORTANT: Remember to observe all safety warnings and precautions when

operating the heater on the automatic or timer modes, either attended or unattended
since a fire risk exists when the heater is accidentally covered, obstructed or displaced.

CAUTION: Do not use if either of the heater’s mains power leads become damaged. If

the supply cord is damaged it must be replaced by the installer or an approved Dimplex
service partner.

Do not sit or stand on the heater.
Ensure minimum clearances between the heater and other objects / surfaces are

maintained.

ELECTRICAL INSTALLATION

WARNING - Minimum clearances and IP zone requirements must be adhered to in

accordance with the current wiring regulations.

Mains cables are not provided with this heater.

WARNING - The electrical installation of this heater must be carried out by a

suitably qualified or trained electrician, and be in strict accordance with current wiring
regulations.

The peak supply must be connected via a switched fused spur with a fuse rated suitably
for the appliances flex, the o-peak supply, via a 20A double pole isolated switch.
In both instances a plug and socket arrangement MUST NOT be utilised. The contact
separation to be a minimum of 3mm.

Failure to follow these instructions will mean that the manufacturer’s instructions have
not been adhered to. THERE ARE NO EXCEPTIONS.

• This heater must be earthed

• Not suitable for connection via a plug top

• Do not locate the heater immediately above, below or in front of a fixed electrical point
i.e. socket outlet.

This appliance is intended for installation to a single phase supply only and is not suitable
for connection to 3 phase supplies.

- 3 -

ELECTRICAL INSTALLATION continued

The heater is not fitted with a mains cable, this should be fitted by the installer. Cable
type (minimum size) H05VV-F 1.5mm² three core for peak and 2.5mm² three core for
o-peak for connection to the fixed wiring of the premises through suitable isolation
devices positioned adjacent to the heater. The supply circuits to the heater must
incorporate a double pole isolating switch having a contact separation of at least 3mm.

In installation the supply cord must be cut to the appropriate length for the electrical
connection point. Excess cable should not be inserted or stored behind the heater.

If, during reassembly of the heater, a part of the thermal insulation shows damage or
deterioration, it should be replaced by an identical part.

WARNING: All electrical connections to the terminal block must be secure to prevent

risk of ignition. Tighten to 2 Nm.

CHILD SAFETY

WARNING - Fixing kit screws are a potential choking hazard.
WARNING - This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of
appliance by a person responsible for their safety.

This appliance can be used by children from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised.

Children aged from 3 years and less than 8 years shall only switch on/o the appliance
provided that it has been placed or installed in its intended normal operating position
and they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.

Children aged from 3 years and less than 8 years shall not regulate and clean the
appliance or perform user maintenance.

WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN

WARNING - Packaging should be disposed of responsibly as the EPS used could

be a potential choking hazard for children.

- 4 -

i

This document is customer property and is to remain with this unit.

These instructions do not cover all the dierent variations of systems nor
does it provide for every possible contingency to be met in connection
with installation.

WARNING: EARTHING

This appliance must be earthed in accordance with the manufacturers
recommendations and in accordance with IEE regulations for electrical
equipment.

Failure to adequately earth the appliance can result in electrical shock
causing severe personal injury or death.

WARNING: HAZARDOUS VOLTAGE

Disconnect all power to unit before installing or servicing.

Hazardous voltage can cause severe personal injury or death.

WARNING: ACCESS TO LIVE PARTS

If the supply cables to the appliance are damaged in anyway, they
must be immediately replaced by a competent person in order to avoid
electrocution which could cause severe personal injury or death.

WARNING

The appliance must be securely fixed to the wall. The installed appliance
could weigh up to 165kg and if it falls o the wall it could cause severe
personal injury or death. It is the responsibility of the installer to ensure
that the appropriate wall fixing is used and that the floor is capable or
bearing the full weight.

- 5 -

WARNING

To avoid a fire hazard the cardboard insert within the heater core must
be removed before the heater is switched on. Also ensure all polystyrene
packaging is removed before the heater is operated. Leaving combustible
packaging in the appliance could lead to fire and cause severe personal
injury, death and damage to property.

CAUTION

The appliance is very heavy (up to 50kg) and care should be taken when
handling during installation to reduce risk of muscular or skeletal injuries.

CAUTION

The appliance should not be repeatedly switched on/o by an external
room thermostat as this could lead to failures of the electronic controller
and may invalidate the guarantee – further clarification SHOULD BE
SOUGHT FROM GDC HELPDESK.

i

CAUTION

During the first 48 hours of operation rooms must be well ventilated as
the heater will produce a smell. Young children, caged birds, or persons
with respiratory complaints must not remain in close proximity to the
appliance during the first 48 hours or operation.

It is important that the appliance bricks are dry and free from mould
growth. Wet or mouldy bricks can lead to an unpleasant odour and or
steam being generated by the appliance which could upset the customer.

- 6 -

- 7 -

Energy Related Product Directive

This product meets the Ecodesign requirements for an electric storage local space heater. Commission

Regulation (EU) 2015/1188.

Model Identifier(s): QM050RF QM070RF QM100RF QM125RF QM150RF

Heat Output

Nominal heat output Pnom 0.50kW 0.75kW 1.00kW 1.25kW 1.50kW

Minimum heat output (indicative) Pmin

Maximum heat output Pmax,c 0.90kW 1.20kW 1.50kW 1.70kW 2.00kW

Auxiliary electricity consumption

At nominal heat output elmax 0.00 0.00 0.00 0.00

At minimum heat output elmin

In standby mode elSB

Type of Heat input, for electronic storage local space heaters only

Electronic heat charge control with room
temperature feedback

Fan assisted heat output Yes

Type of heat output / room temperature control

0.00 0.00 0.00 0.00 0.00

0.00

0.00 0.00 0.00 0.00 0.00

0.000 0.000 0.000 0.000 0.000

Yes

Electronic room temperature control plus week
timer

Contact details

Glen Dimplex Heating and Ventilation
Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF
Tel: [phone]
This product meets the Ecodesign requirements for an electric storage local space heater. Commission
Regulation (EU) 2015/1188.

Yes

Technical Details

Model Identifier(s): QM050RF QM070RF QM100RF QM125RF QM150RF

Input rating +5% / -10% 936/1020W 1435/1560W

Boost Output 230/240V~ 312/340W 478/520W 681/740W 847/920W 1008/1100W

Rated Charge Period: 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours

Max Storage Capacity 7.2kWh 10.9kWh 15.4kWh 19.3kWh 23.1kWh

2042/2220W

2540/2760W

3024/3300W

Fan Wattage 11W 11W 11W 11W 11W

UI Wattage 0.5W 0.5W 0.5W 0.5W 0.5W

Sound Level dB

(measured in test chamber)

Energy Cell Packs Required (047243) 4 6 8 10 12

Height (mm) 730 730 730 730 730

Width (mm) 580 703 865 1069 1069

Depth (mm) 185 185 185 185 185

27 29 32 30 31

- 8 -

All Models

Controls

Controller UI

Digitally controlled, Electronic Thermostat accurate to (±0.2°C).

Timer modes:

7 Day Programmable User Timer, Out All Day, Home All Day

Continuous heat modes:

Frost Protect

Additional Modes:

Away, Boost, Setback

• Graphical display with RGB backlight

• Tactile buttons with audio feedback

• User replaceable battery (Coin-Type)

• Open window detection, Adaptive Start, Advance Time Period

• Wide SP range (7-30°C)

• Automatic Charge Control

• History / Reporting Screens

• Boost Mode, User Adjustable

• Heat Demand % Adjustment

• Child Lock & Heater Lock (PIN-based)

Electronic overheat protection.

Safety

Additional electromechanical overheat protection.
LVD and EMC compliance.

IP Rating IPX4

Battery 3.3V coin cell battery to backup real time clock. Battery life > 5 years.

Supply

Colour / Finish

1/N/1/N/PE ~230-240V (Twin Supply) 230-240V / 50Hz Class I
1/N/PE ~230-240V (Single Supply) 230-240V / 50Hz Class I

Trac White (RAL 9016),
Grille RAL7035

Storage Core High-density bonded magnetite energy cells

Approvals CE & BEAB

Guarantee 2 Years. 10 Years extended available with registration.

Country of Origin United Kingdom

Manufacturer

- 9 -

Glen Dimplex Heating & Ventilation
(GDC Group Ltd)

Product Clearances

WARNING:

DO NOT PLACE OBJECTS WITHIN 300mm OF THE FRONT OF THE HEATER AND
150mm EITHER SIDE

250 mm

150

mm

150

mm

300 mm

Single Supply

It is important to be aware of how your Quantum storage heater has been installed electrically. If you Quantum
has only one electrical connection, it must be carefully configured to work with your o-peak electricity tarri.

Available fixed charge times must be manually programmed into the heater to tell it when to charge; no external
timers or contactors are needed. Up-to 4 digital charge times can be set.

If charge times are not programmed into the heater, the default times will be used which are set-up by default to
support dual-supply installations: 00:00 – 00:00 or 24h charge window.

A 24h charge window in a single supply installation will cause the heater to charge continuously,

including times when o-peak electricity is not available, resulting in larger bills.

NOTE:

If electricity tarri charge times have changed, the digital charge times in the heaters settings must be
checked to ensure they match.

- 10 -

First Time Power-On

A setup wizard will display when the product is powered on for

the first time. This will set the following:

• Time, Date, Daylight Savings Time

• Sound On/O

For information on using the Heaters controls, refer to page 10.

The Heater will then take the User to the Home Screen with the

‘Out All Day’ Timer Mode active

This product is Dimplex Control capable * **.

Important

During initial heat-up, some odour

may be emitted due to the newness of

materials used in manufacture. This is

normal and will disappear after a short

period of use. It is however advisable to

keep the room well ventilated.

Control and monitor your heating and hot water with Dimplex Control. Group heaters into zones to easily control and

track their energy usage. Any time. Anywhere.

Search for Dimplex Control on your device’s app store.

*Requires additional hardware. Sold seperately. Visit Dimplex.co.uk for more information.

**A Dimplex Hub is required for this product to connect to Dimplex Control. For instruction on setting up Dimplex

Hub, please refer to the manual. Manuals can be downloaded at Dimplex.co.uk.

- 11 -

Operation

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY AND/OR DAMAGE

The controls are located on the top of the heater consisting of a display screen and three buttons and a Dial.

1

Display Screen

2

‘Menu’ Button

3

‘Back’ Button

4

‘Selector Dial’

5

‘Enter’ Button

6

‘Advance’ Button

7

Heating Status

1

Out All Day

Heating ON

6

ADVANCE

MENU

BACK

4

3

7

The heater is fitted with an adjustable thermostat enabling the room temperature to be controlled. The minimum

room temperature is 7°C. The maximum temperature is set to 30°C by default. A temperature of 21°C is a common

comfortable room temperature.

NOTE:

Your heater may produce some noise during
operation. This noise is caused by the low
noise fan and expansion and contraction of
the metalwork as it changes temperature,
and is normal for this type of product. Whilst
the noise produced is usually very quiet,
certain environmental factors can make it
more noticeable, such as hard flooring or
minimal furnishings.

2

NOTE:

Should the heater fail to operate, this may
be due to the room temperature being
higher than the thermostat setting.

5

- 12 -

The heater controls can be easily adjusted by using the Dial and buttons on the User Interface.

1. The Home Screen shows the options available at each stage of

adjustment. Here the current target room temperature is displayed along

with the mode of operation. Any use of the Advance function will be

User Timer

displayed here, and pressing the Dial will show the functions which are

enabled.

The currently active mode of operation is displayed at the top of the

screen e.g. ‘Out All Day’ timer.

When the heater is in a timer profile and trying to achieve or maintain a room temperature, ‘Heating On’ will be

displayed, otherwise, ‘Heating O’ will be displayed. The words ‘Heating On / O’ will not be displayed in a manual

mode of operation

When the controller buttons have not been pressed for a long period of time, the display will ‘sleep’ and the text will

disappear. The heater is still on and active in whatever Mode it was set to.

2. Menu - Displays the Main Menu;

- Boost – Activate Boost Mode

- Modes - Set the mode of operation.

- Settings – Time/Date, Temperature units etc.

21

Heating ON

°

C

3. Back returns to the previous screen.

4. Rotate the Dial to navigate through the menus and adjust the required room temperature on the main

screen. The screen colour changes based on the temperature selected, showing deep blue through to bright

red.

5. Press the Dial to enter sub menus and to confirm actions.

6. The Advance button is only used when a Timer Mode is active, it allows the timer schedule to be changed

temporarily by forcing a ‘Heating On’ period to begin or end early.

- 13 -

Timer Modes

Timer Modes oer the most ecient mode of operation for a predictable heat demand. Additional functions such as

Advance and Boost allow the User to make temporary adjustments to timer schedules for a more flexible operation.

Each timer is broken down into 4 definable ‘Heating On’ time periods and temperatures per day, for each day of

the week. Each day consists of a 24-Hour period, starting and finishing at midnight.

When the heater is in a timer profile and trying to achieve or maintain a room temperature, ‘Heating On’ will be

displayed. Otherwise, ‘Heating O’ will be displayed.

It is possible to change the Target Temperature of a ‘Heating On’ period when that period is active. This will

temporarily adjust the Target Temperature for just that instance and will not permanently modify the settings for

the timer in use.

User Timer

°

21

Heating ON

NOTE:

If Adaptive Start is enabled, the heater will maintain the room at the required
temperature for the duration of the heating period. To achieve this, the heater
will begin heating the room before the start of the heating period to ensure
the room is at the required temperature when the period starts.

If Adaptive Start (AS) is disabled, the heater will not operate until the beginning
of the heating period. This should be taken into consideration when setting
the heating periods.

C

ADVANCE

MENU

BACK

See page 22 for instruction on enabling/disabling Adaptive Start.

- 14 -

Available Timer Modes

To choose a timer mode, press Menu from the home screen. Rotate the Dial to highlight ‘Modes’, then press Dial to

select. ‘Timer Mode’ should be highlighted, press the Dial to select.

Manual

ADVANCE

Main Menu

ADVANCE

Modes

ADVANCE

Boost

Timer Mode

Frost Protect

MENU

BACK

21

°

C

MENU

BACK

Mode

Settings

MENU

BACK

A list of Timer Modes will be shown. Their default settings are shown in the table below.

Period 1 Period 2 Period 3 Period 4

User Timer 06:30 – 09:30 21 °C 11:00 – 13:00 21 °C 15:00 – 17:00 21 °C 18:00 – 22:00 21 °C

Home All Day 08:00 – 21:00 21 °C 00:00 – 00:00 00:00 – 00:00 00:00 – 00:00

Out All Day 07:00 - 8:30 21 °C 17:30 - 22:00 21 °C 00:00 - 00:00 00:00 - 00:00

Away Mode

Away Mode does not operate in the same way as the other Timers.
See section ‘Away Mode’ on page 15

Highlight and select one of the available Timer Modes rotating and pressing the Dial.

Timer Mode

User Timer

Home All Day

Out All Day

Away

ADVANCE

MENU

BACK

Home All Day

Select

Modify

Preview

ADVANCE

MENU

BACK

For User Timer, Home All Day and Out All Day, three choices will be available:

Select - This option will activate the timer

Modify - This option allows the timer’s ‘Heating On’ times and Target Temperatures to be modified

Preview - This option displays the timer’s configuration. This is handy to quickly check the timer without being

able to change any values

- 15 -

Modifying a Timer Mode

Each timer is broken down into 4 definable ‘Heating On’ periods and

temperatures per day.

When Modify is chosen, ‘Heating On’ period 1 of 4 for the current day is

displayed. The current day will be highlighted. Rotate dial to highlight

‘Modify’, press dial to select. The current day will be highlighted.

User Timer

User Timer

Modify

Preview

ADVANCE

MENU

BACK

Tuesday

Period 1of4

ON: 07:30

OFF: 09:30

21 °C

ADVANCE

MENU

BACK

Select and change each option by rotating and pressing the dial.

Tuesday

Period 1of4

ON: 07:30

OFF: 09:30

21 °C

ADVANCE

MENU

BACK

Tuesday

Period 1of4

On: 07:30

OFF: 09:30

21 °C

ADVANCE

MENU

BACK

NOTE:

Once modified a Timer
Mode must be selected if
you want to begin using it.

Copy & Paste

To save time when modifying a Timer Mode, the Advance button can be used to copy and paste settings. Individual

heating periods from one day or every heating period from a day can be copied to another day.

Hold ENTER for 2

seconds to paste timer

Wednesday

Period 1 Pasted

ON: 07:30

OFF: 09:30

21 °C

Hold ENTER for 2

seconds to paste timer

Day Pasted

Period 1of4

ON: 07:30

OFF: 09:30

21 °C

Copy time period
to other days

Copy whole day

Highlight Period

Tuesday

Period 1of4

ON: 07:30

OFF: 09:30

21 °C

Highlight Day

Tuesday

Period 1of4

ON: 07:30

OFF: 12:30

21 °C

Hold ADVANCE for

2 seconds

Tuesday

Timer Copied

ON: 07:30

OFF: 09:30

21 °C

Hold ADVANCE for

2 seconds

Day Copied

Period 1of4

ON: 07:30

OFF: 12:30

21 °C

Select day to add

time period

Wednesday

Period 1of4

ON: 07:30

OFF: 12:30

24 °C

Select day to apply

Wednesday

Period 1of4

ON: 09:30

OFF: 12:30

24 °C

- 16 -

The ‘Advance’ Function

The Advance button is only used when a Timer Mode is active and allows the timer schedule to be changed temporarily.

This button allows a ‘Heating On’ period to begin or end early.

This is useful if you are at home when you had not planned to be, or need to leave when you had planned to have the

heating on.

If the heater displays ‘Heating O’ and heat is required, press the Advance button. If the heater is in ‘Heating On’ and

heat is not required, press the Advance button and the heater will stop heating until the beginning of the next ‘Heating

On’ period.

Pre-action State Action Impact

Heating On
(Timer Mode)

Heating O
(Timer Mode)

Heating On
(Advance Active)

Heating O
(Advance Active)

Advance activated

Advance activated

Advance Deactivated

Advance Deactivated

Heating On period switched to Heating O until next scheduled
‘Comfort On’ period.

Heating O switched to Heating On until the next scheduled
‘Heating O’ period.

Heating On switches to Heating O. Appliance in following schedule
set in the currently active Timer Profile

Heating O Switches to Heating On. Appliance in following schedule
set in the currently active Timer Profile

Away Mode

Away Mode temporarily overrides the active mode before returning the Heater back to the previously active mode.

This is handy if you are temporarily away at the shops or on holiday and want your heating to resume as normal

operation automatically when you return.

While active, Away Mode can maintain a minimum room temperature. By default, this is set to 7 °C (frost protection

temperature). This can be modified up to a maximum of 18°C when Away Mode is activated. The heater will also

remember the last Away Mode Target Temperature defined while Away Mode is active.

The Away countdown is set in Hours, a Date and a Target Temperature.

The starting Hours and Date show current time and date. Date and Hours are set separately on the heater, making

the feature useful for popping out to the shops or going away on holiday.

• The date set is the return date; therefore, Away Mode will end at 23:59 of the day before. E.g. if

a return date of 02.02.2018 is set, Away Mode will end at 23:59 on 01.02.2018.

• If hours are set, this will extend away mode end from 23:59 on the day before the date set.

If only hours and no date is set, Away Mode will count from either the current time, or if a date

- 17 -

is set.

Timer Mode

User Timer

Home All Day

Out All Day

Away

ADVANCE

MENU

BACK

Return

Date/Time

Saturday

31-2-18

07:00

21 °C

ADVANCE

MENU

BACK

Return

Date/Time

Away Set

ADVANCE

MENU

BACK

Away

ADVANCE

NOTE:

The Back button can be used to
end the Away Mode countdown
early.

21

Until

31-02-18

07:00

°

MENU

C

BACK

Frost Protect

This mode maintains a room temperature of 7°C and should be used to provide protection against frost. The Heater

will remain in this mode indefinitely until the mode is changed by the User.

To select Frost Protect, rotate Dial to highlight ‘Frost Protect’, press Dial to select. Please note, the temperature is

not user definable.

User Timer

°

21

Heating ON

Frost Protect

C

°

7

C

Heating OFF

ADVANCE

MENU

BACK

ADVANCE

MENU

BACK

Main Menu

Boost

Modes

Settings

ADVANCE

MENU

BACK

Modes

Timer Mode

Frost Protect

ADVANCE

MENU

BACK

- 18 -

Boost Mode

Boost can be activated at any time, when the product is set to any Timer or Continuous heat mode; even if Advance

is active, this mode will provide a temporary ‘Boost’ of heat. For settings, see Boost settings on page 21.

Boost Mode can be activated from the Home Screen by pressing ‘Menu’ to access the Main Menu, then pressing the

Dial to select ‘Boost’. ‘Boost’ will always be listed as the top item on the list.

Main Menu

Boost

Modes

Settings

ADVANCE

MENU

BACK

Main Menu

Boost Temp

25 °C

Boost Time

0 Mins

ADVANCE

MENU

BACK

Boost

Boost Temp

25 °C

Boost Time

30 Mins

ADVANCE

MENU

BACK

Activating Boost will present two selectable options: Boost Temp (Boost Target Temperature) and Boost Time (Boost

Duration Countdown). The default values for these can be set in the Settings Menu.

Rotate and press the Dial to modify these values. Pressing Back will end Boost early, restoring the heater back to its

previously active mode.

• The Boost Temp can be set to any value within the Heater’s Target Temperature Range setting.

• The Boost Time can be increased in the following increments: 30 mins, 1 hour, 2 hours, 3 hours, 4

hours. These increments can be restricted with the Max. Boost Duration Range setting. To modify

this range, see Boost Settings on page 21.

Once the Boost Duration Countdown has reached 0, the Heater will return to the mode that was active before Boost

was activated.

- 19 -

NOTE:

If boost mode is activated and there is not enough stored core energy, peak
rate energy will be used unless disabled in heat source settings.

Product Locks

Product Locks are methods of locking the heater’s controller to restrict access to functions. This can be activated

and configured via the Settings Menu. When Product Lock is activated, the heater continues to run in whichever

mode is currently active and any/all wireless communications remain active if enabled.

Child Lock

This is the simplest locking method and does not utilise a PIN code. It is toggled on/o on the heater’s controller

by pressing and holding the Back button and the Dial for three seconds.

While Child Lock is active, the heater will continue to operate in whatever mode, with whatever settings it had

before the lock was activated.

There are no exception rules with this lock, and the user can only choose to unlock the heater if they wish to change

the temperature, modes or settings.

Heater Lock (PIN Lock)

Heater Lock is the most customisable and secure lock on the heater. This allows the heater to be configured in any

way, then locked into those settings and modes.

When PIN Lock is activated, pressing the Menu button will show one item* that can be selected - ‘Unlock’. Selecting

‘Unlock’ prompts the User to complete the applicable Unlock action:

Menu

Unlock

PIN Lock

123-

Enter 4 Digit

PIN

Manual

PIN Unlocked

*Unless Boost Mode has been

enabled during UI Lock

- 20 -

PIN Lock Exceptions

It is possible to allow the ‘Advance’ and ‘Boost’ functions to be enabled/disabled when PIN Lock is active.

There are up to 4 exceptions. These exceptions include:

- Advance

• Ability to activate using the ‘Advance Button’

- Boost

• Ability to activate using the ‘hotkey’ listed in the Main Menu

• Ability to modify the Boost Temperature

• Ability to modify the Boost Duration

‘Advance Function’ Operation during PIN Lock

If Advance has been enabled during PIN Lock, the Advance button will remain active when PIN Lock is active. This

will function in the same way it would if the controls were not locked: only if the Heater is Locked into a Timer Mode.

• If Advance is enabled during UI lock, the Advance button will function as normal while the Heater is set to a Timer Mode.

• If Advance is Disabled during UI lock, the Advance button will not function.

‘Boost Function’ Operation during PIN Lock

If enabled, Boost will function in the same way as it does when PIN Lock is not active unless modification of Boost

Temperature and Boost Duration have been disabled.

Boost Temperature and Boost Duration will be set to the default values when ‘Boost’ is activated. If either of these

values have been disabled during Product lock, when the user tries to modify them the heater’s display will show the

message ‘Disabled’ and only the default value can be used. The default values can be changed outside of PIN Lock.

- 21 -

Settings

To navigate to the Settings Menu, from the Home Screen:

Main Menu

Press the Menu button to access the Main Menu. Rotate the Dial to

highlight ‘Settings’, then press the Dial. Each of the following headings

relate to an item in the Settings Menu.

Boost

Modes

Settings

Heater Lock

Set Lock

Heater (PIN) Lock can be enabled here by highlighting ‘Heater Lock’ and pressing the Dial to enter the Heater Lock

menu. Highlight ‘Set Lock’, press the Dial, enter a 4-digit PIN code, then pressing the Dial to lock the heater.

Lock Settings

Before PIN Lock is enabled, the User can select ‘Lock Settings’ to enable/disable the Advance and/or Boost functions,

as well as enable/disable modification of the Boost Temperature and Boost Duration. See below.

Settings

Heater Lock

Boost

Setback

Date / Time

Sound

Comms Adaptive

Boost Lock

Three settings can be modified within this Menu:

• Enable / Disable - The ‘Boost’ Menu Item can be Enabled/Disabled while PIN Lock is active.

• Temperature Rule - Modifiable Boost Temperature while PIN Lock is active

- Enable – While Boost is active, the User can modify this value as they normally would

- Disable – Default value will be loaded. When the user tries to modify the value, the UI will show

the following text: ‘Disabled’.

• Duration Rule - Modifiable Boost Duration while PIN Lock is active.

- Enable – While Boost is active, the User can modify this value as they normally would

- Disable – Default value will be loaded. When the user tries to modify the value, the UI will show

the following text: ‘Disabled’

Advance Lock

• Enable / Disable - This setting allows the User to Enable or Disable the Advance button while PIN Lock is

active.

- 22 -

Boost Settings

Default Boost Target Temperature

This is the default Boost Target Temperature that is used when ‘Boost Mode’ is activated.

Max Boost Duration

This is the maximum length of time that the user is able to activate ‘Boost’ for. Shown in minutes (when under

an hour) or hours (if over an hour) in the following increments: 30 mins, 1 hour, 2 hours, 3 hours, 4 hours.

The value chosen will be the max allowed when boost is activated. This is required for the Boost Duration Lock

to function.

Setback Settings

Setback is a function that only modifies Timer Mode operation. When Setback is enabled it overrides any ‘Heating O’

period to maintain a constant temperature.

This can be used to prevent the room temperature from falling below a minimum value while there is no demand for

heat (‘Heating O’).

The value of this temperature is restricted to a value between 8 and 19 °C. This is because Setback should not be treated

as a regular ‘Heating On’ period.

Date & Time Settings

This allows the Time, Date and Daylight Savings Time settings to be modified.

Sound Settings

Audio feedback when the user presses a button can be enabled or disabled here.

‘Comms’ (Communications) Settings

This allows Wireless Connectivity features to be enabled or disabled. Entering this menu item will display a list of

available communications methods to that heater.

- 23 -

Adaptive Settings

Open Window Detection

This is a global setting that can interrupt any active mode. Activating this setting enables Open Window

Detection to switch the Heater to a ‘Heating OFF’ state if it detects an open window in the room it’s operating

in.

Adaptive Start

Adaptive Start is predictive function that only modifies Timer Mode operation. This function models the

heating characteristics of the room and uses that information to pre-heat the room for only the time required

to achieve the Target Temperature by the start of the ‘Heating On’ period.

For example, with Adaptive Start o, the ‘Heating On’ time is the time that the Heater will begin to try and

achieve the Target Temperature. With Adaptive Start On, the Heater will begin to heat the room before

the User-defined ‘Heating On’ time so that the Target Temperature is achieved when the User defined the

‘Heating On’ start time.

NOTE: Adaptive Start

This is a continuously learning function and will be aected daily by changes in the
heater’s environment. The heater will take into account the starting temperature of
the room so pre-heating should remain accurate.

It is important that if multiple heaters are installed in one room that all heaters have
the Adaptive Start (AS) function enabled. If this is not the case, heaters with AS
enabled will pre-heat the room to the desired target temperature before the heaters
with AS disabled attempt to output heat.

It is likely that if two heaters are required in one room, that the output from one
heater may not be sucient to heat the room alone. This may cause the pre-heat
time calculation to extend to a large degree if the heaters do not all have AS enabled.
This may lead to heat at unwanted times and excessive wear to some heaters.

A two-hour limit is enforced on the calculation, however, if all heaters have AS
enabled and pre-heating takes over one-hour, extreme environmental factors may
be aecting the calculation or the heaters may be under sized for the room. Please
contact us for support if your pre-heat time seems excessive.

NOTE: Open Window Detection

In environments where the product may read sudden decreases in temperature,
this feature may activate in error. This can occur in drafty or poorly insulated
environments as well as if the heater is undersized for the room. This feature should
be disabled using the instructions above if activating for reasons other than the
intended purpose. If you think that your environment is not as described here and
this feature is activating, please contact our customer care team with the details on
the rear page of this document.

- 24 -

Error Codes

Error codes are to be defined as a list. Each error code must be defined as a perimeter that Central Control can read.

Fault Code Description

20

20

21

Component thermistor hardware fault

22

23

24

30

32

Component overheat

33

34

40 Internal serial comms error

41 Heating element fault

50 Open window detected

51 Low water

52 Heat output disabled

53 Time loss error

54 Occupancy sensor not detected

55 Unknown error

60 Wireless communication module error

61 Hub connection error

- 25 -

Battery Replacement

IMPORTANT:

Before replacing the battery ensure the heater is isolated from the electricity supply.

NOTE:

Battery should be disposed of in an appropriate manner

This product is fitted with a replaceable battery in the controls. To replace the battery, follow the steps below:

1. Push a small flat headed screwdriver into the opening on the right hand side of the User Interface (Fig. 1) to release

the clip.

2. Lift the User Interface module out away from the heater being careful not to damage the cable

3. Unscrew the battery cover (Fig. 2) to gain access to the battery holder.

4. Use a small flat headed screwdriver to remove the battery from the battery holder and replace the battery.

5. Replace the battery access cover.

6. Push the User Interface module back into place, again avoiding damage to the cable.

Fig. 2Fig. 1

- 26 -

Important

During the initial operation, some odour may be noticed due to the newness of materials used in manufacture. This
is normal and will disappear after a short period of use. It is however advisable to keep the room well ventilated

Cleaning

WARNING - ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE

CLEANING THE HEATER.

Before commencing cleaning, isolate the heater from the electrical supply and allow it to cool. The outside can be
cleaned by wiping it over with a soft dry cloth. Do not use abrasive cleaning powders or furniture polish, as this
can damage the surface finish.

- 27 -

Guarantee

What does a Dimplex Guarantee cover?

Dimplex products deliver reliable service for use in dwellings. All Dimplex products are individually tested before
leaving the factory.

If you are a consumer and you experience a problem with your Dimplex product, which is found to be defective due
to faulty materials or workmanship within the Guarantee Period, this Dimplex Guarantee will cover repair or - at the
discretion of Dimplex – replacement with a functionally equivalent Dimplex product.

The Dimplex Guarantee Period is two calendar years from the date of purchase of your Dimplex product, or the date
of delivery of the product, if later. The Dimplex Guarantee is conditional upon you providing the original purchase
receipt as proof of purchase. Please therefore retain your receipt as proof of purchase.

If you do experience a problem with your Dimplex product please call the Helpline on +44 [0]344 879 3588 or
visit https://www.dimplex.co.uk/support. For ROI please email [e-mail] or call +353(0)1
842 833. We will need details of your Dimplex product, it’s serial number and a description of the fault which has
occurred. You can find the model number and serial number for your Dimplex product on the heaters side. Once we
receive your information and proof of purchase we will contact you to make the necessary arrangements.

If your Dimplex product is not covered by this Dimplex Guarantee there may be a charge to repair your product.
However, we will contact you for agreement to any charges before any chargeable service is carried out.

What is not covered by a Dimplex Guarantee?

The Dimplex Guarantee does not cover any of the following:

• Any fault or damage to your Dimplex product due to faulty materials or workmanship occurring outside the
two year Guarantee Period.

• Any fault or damage occurring to any pre-owned Dimplex product or to any other equipment or property.

• Accidental damage to your Dimplex product or damage to your Dimplex product from external sources (for
example, transit, weather, electrical outages or power surges).

• Fault or damage to your Dimplex product which is:

• Not due to faulty materials or workmanship or which is due to circumstances outside Dimplex’s control.

• Caused by use of your Dimplex product for anything other than normal, dwelling usage in the country where
it was purchased.

• Caused by any misuse, abuse or negligent use of the Dimplex product, including but not limited to any failure
to use it in accordance with the Operating Instructions supplied with the product.

• Caused by any failure to assemble, install, clean and maintain your Dimplex product in accordance with the
Installation Instructions supplied with the product unless this was carried out by Dimplex or its authorised
dealers.

• Caused by repairs or alterations to your Dimplex product not carried out by Dimplex service personnel or its
authorised dealer(s).

- 28 -

• Caused by use of any consumables or spare parts for your Dimplex product which are not Dimplex specified.

Terms and Conditions

• The Dimplex Guarantee is valid for Dimplex from the date of purchase of your Dimplex product from a
recognised retailer in the country of purchase and use, or the date of delivery of the product if later, always
provided the original receipt has been retained and is produced as proof of purchase.

• You must provide to Dimplex or its authorised agents on request the original receipt as proof of purchase
and - if required by Dimplex - proof of delivery. If you are unable to provide this documentation, you will be
required to pay for any repair work required.

• Any repair work under the Dimplex Guarantee will be carried out by Dimplex or its authorised dealer(s) and
any parts that are replaced will become the property of Dimplex. Any repairs performed under the Dimplex
Guarantee will not extend the Guarantee Period.

• Any replacement of your Dimplex product by Dimplex during the Guarantee Period will not start the Guarantee
period afresh.

• The Dimplex Guarantee does not entitle you to recovery of any indirect or consequential loss or damage
including but not limited to loss or damage to any other property.

• The Dimplex Guarantee is in addition to your statutory rights as a consumer and your statutory rights are
not aected by this Dimplex Guarantee.

If you have any questions about what the Dimplex Guarantee covers and does not cover or how to claim under the
Dimplex Guarantee, please contact us using the information on the back page.

Contact details

Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF

Important

For electrical products sold within the European Community. At the end of the electrical products

useful life it should not be disposed of with household waste. Please recycle where facilities exist.

Check with a Local Authority or retailer for recycling advice in your country. Batteries should be

disposed of or recycled in accordance with WEEE Directive 2012/19/EU. Packaging should be

recycled where possible.

- 29 -

- 30 -

- 31 -

Customer Helpline: 0344 879 3588

[e-mail]

www.dimplex.co.uk

Glen Dimplex Heating & Ventilation

Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF

© Glen Dimplex. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior
permission in writing of Glen Dimplex.

This product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC

- 32 -