Dimplex PX01001 Installation And Operating Instructions Manual

2. The location of the control is important, it will not function
correctly if above or within 500mm of a heat source or
draught. Care must also be taken not to obscure the slots at
the top or bottom of the control and that it is not exposed to
direct bright sunlight or close to a lamp fitting. Best
temperature accuracy will be achieved by mounting on an
internal wall or partition.

3. The pattress boxes (not provided) should have a depth of at
least 25mm. Plastic pattress boxes with vertical pillars are not
suitable.

Vertical tabs in metal pattress boxes should be removed.
Ensure all entries into the pattress boxes are sealed to
prevent draughts.

4. Before fitting to the mounting box setback temperature,

comfort temperature and comfort period must be selected. To
do this, adjust the appropriate dial on the reverse of the PCB.

5. The supply cable is not provided and should therefore be
selected to suit the appliance.

Warning: Although the control does not need an earth, the

appliance probably does. Ensure that the mounting box is
fitted with an earth terminal for earth continuity to the
appliance.

6. To connect the control in circuit wire in to the clearly marked
terminal block on the rear of the controller. The control must
only be connected via fixed wiring.

7. Secure the control to the pattress box such that there are no

gaps between the controller and wall or pattress box.

Note: If tamperproof screws are required they should be M3 x 40mm
long, counter sunk with a head diameter of no more than 6.5mm.

Installation and
Operating Instructions

Press Button Delay Timer - Model No. PX01001

Safety Warnings

1. WARNING: DO NOT USE THIS APPLIANCE IN THE
IMMEDIATE SURROUNDINGS OF A BATH, A SHOWER
OR SWIMMING POOL

2. WARNING: DO NOT USE WHERE EXCESSIVE DUST OR
MOISTURE IS PRESENT

3. WARNING: FOR USE IN NORMAL POLLUTION
SITUATIONS ONLY

General Description

The PX01001 timer/thermostat can be used in conjunction with
heating appliances. They may be flush or surface mounted using a
standard 25mm box. The control is rated at 16A (250VAC) and can
be used in conjunction with heating appliances wit h a m ax i m um t ot a l
input of 13 A resistive L.C. 230V - 50Hz. The controller cannot be
used with a Quartz heater without a suitable i n-line contactor.
Control action: Type 1B

Operating Instructions

The PX01001 controls the room temperature by interrupting the
power supply to the appliance, therefore the appliance should
always be switched on and its thermostat set to maximum
temperature. Note this will not be reached if the pre-determined
maximum level is below that of the appliance thermostat setting.

When the comfort mode is activated by pressing the

centre of the control face, the green light illuminates.
The comfort mode allows the room to be heated to a pre­ determined temperature for a pre-determined time
period.

The red light indicates that the heater is operating.
Note that the heater will remain on for a minimum of 1

minute.

The red light may also b e i l l uminated in the set back
mode when the PX01001 switches the heater on to
maintain the predetermined background temperature.

Installation

Before undertaking installation work, ensure the electricity supply is
disconnected from any relevant fixed wiring.

1. The control and heater should be installed in compliance with
the IEE Wiring Regulations

comfort
control

Dimplex

TOUCH

85mm

85mm

25mm

boost

Main Dimensions

boost

Ensure 500mm clearance from any heat source or draught.

T0105/004/A

General Cleaning

WARNING
BEFORE UNDERTAKING CLEANING WORK ON THE
CONTROLLER OR APPLIANCE IMMEDIATELY DISCONNECT
THE ELECTRICITY SUPPLY BY SWITCHING OFF AT THE
ADJACENT DOUBLE POLE SWITCH.

The outside of the appliance should be wiped over with a soft damp
cloth and then dried. Do not use detergents or abrasives.

After Sales Service

Your Dimplex Comfort Control is guaranteed for one year from date
of purchase. We undertake to exchange or repair free of charge
within this period, any part found to be defective.

Should you require after sales service, please get in touch with the
supplier through whom you purchased the appliance , or your
nearest Service Agent.

Please do not initially return a faulty appliance or part of an appliance
to us as this may result in transit damage and/or delay in providing
service. Let us know your difficulty quoting the model number and
series of the appliance. We will then take the appropriate action.

L

Live

Output
Live
Neu-

N

Setback
temp.

Comfort
temp.

Timing

16ºC 25ºC 5ºC 19ºC

Comfort Temperature Setback Temperature

Glen Dimplex UK Ltd
Millbrook House
Grange Drive
Hedge End

Southampton
Hampshire SO30 2DF

Customer Services: Tel. [phone]
Fax. [phone]
email customer.services@glendimplex

Republic of Ireland Tel. [phone]

HEATER

OUT

IN

IN
OUT

L

N

Control SWITCHED

FUSED

SPUR

Minimum 500mm

230VAC MAINS

FROM FUSED or

BREAKERED

SOURCE

Ensure the heater is properly
earthed with the Fused Spur

Wiring Diagram

HEATER

OUT

IN

IN
OUT

L

N

Control SWITCHED

FUSED

SPUR

Minimum 500mm

230VAC MAINS

FROM FUSED or

BREAKERED

SOURCE

Ensure the heater is properly
earthed with the Fused Spur

Alternative

0

240

Timing (Mins)

Installation contd..