Dimplex LEE Series, LEE20LED Owner's Manual

LEE

(LEE20LED)

AUS

8/50871/0 Issue 2

OCN : 11003

The product complies with the European Safety Standards and the European Standard Electromagnetic Compatibility (EMC). These cover the essential requirements of EEC Directives

1

1

2

3

280580

730

LEE

2

II

I

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice

When using electrical appliances, basic
precautions should be followed to reduce

the risk of re, electric shock, and injury to

persons, including the following:
If the appliance is damaged, check

immediately with the supplier before
installation and operation.

Do not use this appliance in the immediate
surroundings of a bath, shower or swimming
pool.

Do not use outdoors.
This appliance must not be located

immediately above or below a xed socket

outlet or connection box.
WARNING : The appliance carries
the Warning Symbol indicating that it

must not be covered or has a Do not
cover label. Do not cover or obstruct
in any way the heat outlet grille located
underneath the appliance Overheating will
result if the appliance is accidentally covered.
Do not place material or garments on the
appliance, or obstruct the air circulation
around the appliance, for instance by
curtains or furniture, as this could cause

overheating and a re risk.

In the event of a fault unplug the heater.
Unplug the appliance when not required
for long periods. The supply cord must be
placed on the right hand side of the heater
away from the heat outlet underneath the
appliance. This appliance is not intended
for use by persons (including children)
with reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by Children without
supervision. Children should be kept away
unless continuously supervised. Children

shall not turn on/off the appliance.Children
shall not plug in, regulate and clean the
appliance or perform user maintenance.

The appliance must be positioned so that
the plug is accessible.

Although this appliance complies with
safety standards, we do not recommend
its use on deep pile carpets or on long hair
type of rugs.

If the supply cord is damaged it must be
replaced by the manufacturer or service

agent or similarly qualied person in order

to avoid a hazard.
CAUTION: In order to avoid a hazard due

to inadvertent resetting of the thermal cut­out, this appliance must not be supplied
through an external switching device, such
as a timer, or connected to a circuit that is
regularly switched on and off by the utility.

CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given where
children and vulnerable people are present.

General

Unpack the heater carefully and retain the packaging for

possible future use, in the event of moving or returning the re

to your supplier.

These models are tted with castors and handles so they can

be moved from room to room with ease, and are freestanding
and normally positioned against a wall.

The choice of 1kW or 2kW heat output is provided by the fan
heater, which is located at the bottom of the unit.

The re incorporates a ame effect, which can be used with or

without heating, so that the comforting effect may be enjoyed

at any time of the year. Using the ame effect on its own only

requires little electricity.
Before connecting the heater check that the supply voltage is

the same as that stated on the heater.

Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which

is related to the operation of the ame effect. This is normal
and should not be a cause for concern.

Electrical Connection

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.

Before switching on, please read the safety warnings and
operating instructions.

Controls - see Fig. 2

Three switches provide a choice of heat settings. A switch is in
the ON position when the side with the markings on (i.e. I, l, or

II) is pushed in.

Switch 1 (I) Controls the electricity supply to the heater

and the ame effect.

Note: This switch must be in the ON (I)
position for heater to operate with or without

heat.
Switch 2 (I) Provides 1kW heat output
Switch 3 (II) Provides 2kW heat output with switch 2 in the

ON positon also.

Thermostat (T) - see Fig.2

In order to maintain a certian room temperature, set the controller
to ‘max’. Operate the

heater at full power until the required room
temperature ie reached. Turn back the thermostat control knob
until the heater turns off with an audiable ‘click’. This temperture
will be kept almost constant by the thermostatic control switching
ON and OFF automatically. Please note that the appliance can
only be switched ON when the thermostat setting is higher than
the room temperature.

Thermal Safety Cut-out

A thermal safety cut-out is incorporated in the heater to
prevent damage due to overheating. This can happen if the
heat outlet was restricted in any way. The heater will switch
on once the obstruction has been removed and the heater has
cooled. If the cut-out continues to operate intermittently, the
heater should be switched off and a service agent contacted.

WARNING: This heater is not equipped with a device to
control the room temperature. Do not use this heater in small
rooms when they are occupied by persons not capable of
leaving the room on their own, unless constant supervision is
provided.

Light Emitting Diode

This re is tted with LED (Light Emitting Diode) bulbs in place

of traditional incandescent bulbs. These generate the same
light levels as traditional bulbs, but use a fraction of the energy
consumed.

Recycling

At the end of the electrical products useful life
it should not be disposed of with household
waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for
recycling advice in your country.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully
with a soft cloth. DO NOT use proprietary glass cleaners.

To remove any accumulation of dust or uff the soft brush

attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.

After Sales Service

Please see the separate Warranty leaet for details of your

Warranty & After Sales Service including contact details.

Should you require after sales information or assistance with this
product, please contact Glen Dimplex Australia on 1300 556 816
(AUS) / 09 274 8265 (NZ) or visit our website at www.dimplex.

com.au (AUS) / www.dimplex.co.nz (NZ).

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE
POWER SUPPLY BEFORE ATTEMPTING ANY

MAINTENANCE.

Glen Dimplex Australia Pty Ltd.
1340 Ferntree Gully Road,
Scoresby,
VIC 3179,
Australia

www.dimplex.com.au
[e-mail]

Ph: 1300 556 816

Fax: [phone]

Glen Dimplex Australasia Ltd.
35 Harris Road,
East Tamaki,
Auckland
New Zealand

www.dimplex.co.nz
[e-mail]

Ph: 09 274 8265
Fax: [phone]