Dimplex KDS6401E CONTEMPRA Parts & Service Manual

CONTEMPRA

MODEL KDS6401E

PARTS & SERVICE MANUAL

TABLE OF CONTENTS

OPERATION PAGE 3

PARTS DRAWING PAGE 7

WIRING SCHEMATICS PAGE 8

PARTS LIST PAGE 9

LIGHT BULB REPLACEMENT PAGE 10

MAIN POWER ON/OFF SWITCH REPLACEMENT PAGE 11

FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 12

HEATER ON/OFF SWITCH PAGE 13

HEATER THERMOSTAT REPLACEMENT PAGE 14

POWER CORD REPLACEMENT PAGE 15

HEATER ASSEMBLY REPLACEMENT PAGE 16

2

KDS6401E CONTEMPRA

NOTE

A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not
essential in all cases. A dedicated circuit will be required if, after installation, the
circuit breaker trips or fuse blows on a regular basis when the heater is
operating. Additional appliances on the same circuit may exceed the current
rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp
edge and ensure that the power cord is stored or secured to avoid tripping or
snagging to reduce the risk of fire, electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes
and other applicable regulations to reduce the risk of fire, electric shock and
injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire,
electric shock or injury to persons, always use a licensed electrician.

CONTEMPTA INSTALLATION

1. Make sure the unit is switched OFF (refer to operating instruction section).

2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you
may use an extension cord rated for a minimum of 1875 watts

OPERATION

To access the controls go to the front panel of the unit (refer to diagram below)

1. MAIN ON/OFF SWITCH
The on/off switch supplies power to all unit functions (heat/flame)

2. HEATER ON/OFF SWITCH

The HEATER ON/OFF SWITCH supplies power to the heater fan and the
heater element and must be turned on before heat can be created.

3. HEATER THERMOSTAT CONTROL

To adjust the temperature to your individual requirements, turn the heater
thermostat control knob clockwise all the way to turn on the heater. When the
room reached the desired temperature, turn the thermostat knob counter
clockwise until you hear a click. Leave in this position to maintain the room
temperature at this setting. For additional heat, turn clockwise until you hear
the click again and the heater will turn on. To turn the heater off, switch the
HEATER ON/OFF SWITCH to the OFF position.

NOTE:- When the heater is switched ON, the heater fan will operate. The heater
element may or may not be on, depending on the thermostat control setting (SEE
“HEATER THERMOSTAT CONTROL” above).

3

KDS6401E CONTEMPRA

RESETTING THE TEMPERATURE CUTOFF SWITCH

This unit is equipped with a thermostat, which controls the temperature of the
room. It does this by turning the heater on and off. The heater is protected with a
safety device to prevent overheating. Should the heater overheat, an automatic
cut out will turn the heater off and it will not come back on without being reset. It
can be reset by switching the ON/OFF SWITCH to OFF and waiting 5 minutes
before switching the unit back on.

CAUTION

If you need to continuously reset the heater, unplug the unit and call Dimplex North
America Limited at 1-800-668-6663.

MAINTENANCE

WARNING

Disconnect power before attempting any maintenance or cleaning to reduce the
risk of fire, electric shock or damage to persons.

4

KDS6401E CONTEMPRA

LIGHT BULB REPLACEMENT

Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid
accidental burning of skin.

Light bulbs need to be replaced when you notice a dark section of the flame or
when the clarity and detail of the log exterior disappears. There are two bulbs
under the log set which generate the flames and embers.

GLASS CLEANING

The glass is cleaned in the factory during the assembly operation. During
shipment, installation, handling, etc., the glass surface may collect dust particles;
these can be removed by buffing lightly with a clean dry cloth.

To remove fingerprints or other marks, the glass can be cleaned with a damp cloth
using a good quality household glass cleaner. The glass should be completely
dried with a lint free cloth or paper towel. Do not use abrasive cleaners on glass
surface or spray liquids directly onto any surface.

contempraef SURFACE CLEANING

Use warm water only to clean painted surfaces of the contempraef. Do not use
abrasive cleaners on surface or spray liquids directly onto any surface.

TO REPLACE THE LIGHT BULBS

1. On the back of the contempra

ef

remove the screws from the light access

cover.

2. Remove the light access cover.

4. Reach into the opening, locate and examine the bulbs to determine which
bulb(s) required replacement.

1. Unscrew the bulb(s) counter clockwise.

2. Insert new bulb(s).

7. Install the light access cover and install the screws

HELPFUL HINTS

It is a good idea to replace all light bulbs at one time if they are close to the end of
their rated life. Group replacement will reduce the number of times you need to
open the unit to replace light bulbs.

BULB REQUIREMENTS

Quantity of 2 clear chandelier or candelabra bulbs with an E-12 (small) socket
base, 60 watt rating. Example GE 60BC of Philips 60 CTC.

5