Dimplex IL095 Installation And User Manual
IMPORTANT:
This booklet should be left with the user after
installation and demonstration.
It should be kept in a safe place, as you may need
to refer to it for general instructions
or future maintenance
DIMPLEX IL095
INSTANT INLINE UNVENTED
WATER HEATER
Installation and User Guide
2
CONTENTS
If you experience any difficulty with the installation or operation of your new
water heater, then please refer to the “What to do if things go wrong” section
in this manual before contacting us.
INTRODUCTION
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH
REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION
OR INSTRUCTION CONCERNING USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY
DO NOT PLAY WITH THE APPLIANCE.
Thank you for purchasing a quality Dimplex IL095 manufactured in England.
To enjoy your new unit at its best, please take time to read this manual thoroughly to
familiarise yourself with all instructions, BEFORE beginning installation.
• Your IL095 has been designed for convenience, economy and safety of use, provided that it is
installed, used and maintained in good working order and in accordance with our instructions and
recommendations.
• All wiring and installation must be supervised by a suitably qualified person.
• THIS APPLIANCE MUST BE EARTHED.
• The installation must be in accordance with the current edition of BS.7671 (the “IEE Wiring
Regulations”) and “Part P” of the “Building Regulations” in force at the time of installation.
Installations outside England and Wales must also conform to any local regulations in effect.
• This appliance is intended to be permanently connected to the fixed electrical wiring of the mains
supply with its own dedicated supply.
• This appliance must NOT be fitted where it may be subjected to freezing conditions
DO NOT switch the appliance on if you suspect it of being frozen.
Wait until you are sure it has thawed out.
• Isolate the mains electrical and water supply before removing the front cover of the appliance.
Section
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to install your IL095 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commissioning your IL095 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to use your IL095 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What to do if things go wrong (1) Self Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimplex After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Accessories and Common Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .
What to do if things go wrong (2) Professional Service . . . . . . . . . . . . . . . . . . . . . . .
How your IL095 Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guarantee and Contact Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
2
2
3
7
8
9
9
9
10
11
12
IMPORTANT SAFETY INFORMATION
3
WARNING: ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A SUITABLY
QUALIFIED PERSON.
WARNING: DO NOT INSTALL THIS UNIT WHERE IT MAY BE SUBJECTED TO FREEZING
CONDITIONS.
BEFORE YOU START
Check that the mains electric is capable of supplying the required current.
See the rating plate for current requirements.
Check the pressure of the main water supply.
To operate correctly, the unit requires the following running pressures.
Check the rating plate to see which applies:-
Dynamic Water Pressure
Basin Shower
Model
Minimum Maximum Minimum Maximum
Up to
9.5kW
10 psi (0.7 bar)
(69 kPa)
150 psi (10.3 bar)
(1035 kPa)
15 psi (1.1 bar)
(103 kPa)
150 psi (10.3 bar)
(1035 kPa)
Up to
10.8kW
15 psi (1.1 bar)
(103 kPa)
150 psi (10.3 bar)
(1035 kPa)
20 psi (1.4 bar)
(138 kPa)
150 psi (10.3 bar)
(1035 kPa)
Up to
12.0kW
20 psi (1.4 bar)
(138 kPa)
150 psi (10.3 bar)
(1035 kPa)
25 psi (1.8 bar)
(172 kPa)
150 psi (10.3 bar)
(1035 kPa)
FIXING THE UNIT TO THE WALL
Deciding the position
• If being used in a public place, position the unit out of reach to discourage vandalism.
• Fit the unit onto a flat piece of wall, well away from any potential splashes of water or spray.
• Position the unit either upright or lengthways (diagram 1), whichever is most convenient for
plumbing and wiring.
Remember to keep the lengths of hot water pipe to a minimum in order to save energy.
• If the unit is to supply a basin, you can fit it either above or below the basin.
HOW TO INSTALL YOUR IL095
4
Deciding the wiring route
• You have a choice of whether to feed the electric cable
through the side or through the back of the unit.
• If it going through the side of the unit, cut out the
plastic lug to expose the grommet (diagram 2).
• If is going through the back of the unit, cut through the
grommet on the backplate with a sharp knife (Take Care!).
Make sure you do not remove the grommet from the backplate (diagram 3).
Feed the cable through the grommet before you fix the unit to the wall.
Fixing to the wall
• Undo the retaining nuts and take the front cover
off the unit. Hold the backplate in position against
the wall whilst you mark the four fixing holes.
• Drill the holes and fix the unit to the wall using the
four No.8 x 38mm wood screws supplied.
Plumbing the unit
WARNING: IF A NON RETURN VALVE IS FITTED IN THE INLET FEED TO THE UNIT,
THEN THE INSTALLATION SHOULD ALSO INCLUDE A 3.5 BAR PRESSURE
REDUCING VALVE AND A 6 BAR PRESSURE RELIEF (EXPANSION) VALVE
Loading...