Dimplex EvoRad Series, EvoRad2BTA, EvoRad2BT Instruction Manual

EvoRad2BT & EvoRad2BTA

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

As with all portable heating appliances - This product is only suitable for well insulated spaces or occasional use

08/53302/0 (UK) Issue 5

The product complies with the European Safety Standards EN60335:2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014:1,
EN55014:2, EN61000:3-2 and EN61000:3-3 which cover the essential requirements of EMC Directive 2014/30/EU and the LVD Directive 2014/35/EU.

1

Bluetooth

Neon

Standby

LCD Display

Programme

Temperature
Increase

Cable wrap &
plug storage

Temperature
Decrease

Mode/Pair

Heat Neon

Mains neon

Desired
Temperature

Selected
Mode

Selected Heat
Seng

Standby Mode

Flashing

Time for next status
change (ON at 15:20)

Acv

Flashing

2

3

Auto Mode

Boost Mode

4 5

Manual Mode

7 8

9

Heat status

e segment

10

Heat seng

Set temperature

Model Identier(s):

Heat output

6

Nominal heat output Pnom 2.0 2.0

Minimum heat output (indicative) Pmin 0.8 0.8

Maximum continuous heat output Pmax,c 2.0 2.0

Auxiliary electricity Consumption

At nominal heat output elmax 0.0 0.0

At minimum heat output elmin 0.0 0.0

In standby mode elSB 0.0005 0.0005

Type of heat output/ room temperature control

With electronic room temperature control plus day timer

Contact details

GDHV, Milbrook House, Grange Drive,
Hedge End, Southampton, SO30 2DF

EvoRad2BT EvoRad2BTA

kW

kW

kW

kW

kW

kW

Yes

Important Safety Advice

IMPORTANT: If the appliance is damaged,

check immediately with the supplier before
installation and operation.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience or knowledge if they have
been given supervision or instruction concerning
the use of the appliance in a safe way and
understand the hazards involved. Children shall
not play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
Children of less than 3 years should be kept
away unless continuously supervised. Children
aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that
it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning
the use of the appliance in a safe way and
understand the hazards involved. Children aged
from 3 years and less than 8 years shall not plug
in, regulate and clean the appliance or perform
user maintenance.
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.

This heater carries the warning symbol

indicating that it must not be covered.
DO NOT use the heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
WARNING: This heater must not be used in a
bathroom.

DO NOT place the heater directly below a xed

socket outlet.
WARNING: In order to avoid overheating, do
not cover the heater.
We recommend that you open a window to
ventilate the room when using the heater for

the rst time.

Unplug the heater when not required for long
periods.
IMPORTANT: If the mains lead of this appliance
is damaged, it must be replaced by the
manufacturer or its service agent or a similarly

qualied person in order to avoid a hazard.

DO NOT use the heater where gas, petrol, paint

or other inammable goods are used or stored.

Warning: The heater complies with stringent safety
standards but to ensure efcient operation SURFACES
OF THE HEATER WILL BECOME HOT AND CONTACT
WITH THESE AREAS SHOULD BE AVOIDED, particularly

between the ns on the top and sides.

The heater is designed for operation on an AC electricity
supply, and is suitable for use in domestic dwellings and
similar indoor locations.

Always ensure that the appliance is stood on a rm, level
base near to, but not directly beneath, a suitable xed

socket outlet.

The heater is tted with castors and a handle for ease of

movement.
It is supplied with a cord and plug ready for use. The supply

cord should be uncoiled before use (see ‘Storage’).

DO NOT pull the heater along by the mains lead.

Fitting the Foot & Castor Assemblies (Refer
to Fig.2)

WARNING: DO NOT OPERATE THE HEATER WITHOUT
THE TWO FOOT & CASTOR ASSEMBLIES SECURELY
FITTED.

WARNING: THE HEATER IS HEAVY, TAKE CARE WHEN
LIFTING AND ENSURE THAT IT IS WELL SUPPORTED
DURING ASSEMBLY AND USE TO PREVENT IT FROM
TOPPLING OVER CAUSING INJURY OR DAMAGE.

1. Remove the box containing the foot & castor assemblies
from the product packaging.

2. Carefully turn the heater upside down supporting it on a
soft surface (to avoid damage), request the assistance of
a second person if required.

3. Remove the rst set of foot xing screws from the bottom
of the ns identied by a label and set aside carefully. Line
up the rst foot as indicated in g.2 and press it down into
position, drop the two foot xing screws into the two screw

bosses and tighten each one fully with your screw driver.

4. Repeat the above process (3) for the second set of

xing screws on the second n indicated by a label. Once
completed do a nal check to ensure that both feet are

secured properly.

5. Lift and turn the heater upright again (with assistance if
required) and stand it on its castors as shown in g.1, it is

now ready for use.