Dimplex CPTSW, CPTS Installation Instructions

Installation and Operating Instructions
Compact Towel Rail Model : CPTS & CPTSW
Dimensions
(millimetres)
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Table 1
Model Rails Watts Weight(kg) Finish
CPTS 12 120 7.4 Chrome
CPTSW 12 150 7.4 White
Important Safety Advice
WARNING - THE SURFACE OF THIS
RADIATOR CAN BE HOT.
In order to be effective the towel rail will get hot, however momentary contact with any part of it should not cause injury.
The heater is to be installed so that switches and other controls cannot be touched by a person in the bath or shower
CAUTION - This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3
08/51910/1 (UK) Issue 1
Fig. 1
years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
Precautions should be taken to ensure that prolonged contact with the towel rail cannot occur. Particular care should be taken in
conned areas where accidental prolonged
contact with the rail could be more likely to occur.
This appliance should only be used to dry fabrics washed in water using commonly available detergents.
A means for disconnection must be
incorporated in the xed wiring in accordance
with the wiring rules. If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualied persons in order
to avoid a hazard. IMPORTANT - If the towel rail is to be installed
in a place used by the public, a warning notice should be placed adjacent to the rail advising that the surface can be hot.
WARNING - the towel rail is a sealed unit and is filled and sealed under controlled conditions. Under no circumstances should the seal of the unit be compromised
WARNING - In order to avoid a hazard for very young children, this appliance should be installed so that the lowest heated rail is
at least 600mm above the oor.
General
The towel rail is designed to provide an all year round service for airing towels and articles of clothing. It is not intended to provide a sole heating service, but will take the chill off a small size bathroom,
lavatory or en suite.
No routine maintenance is necessary apart from occasional cleaning.
The unit is splashproof to IPX5 standard.
(A) 4 mounting collars,
(B) 4 mounting brackets,
(C) 4 collar xing screws,
(D) 4 bracket pins,
(X) 4 wall plugs,
(Y) 4 wall mounting screws,
Electrical
WARNING - This appliance must be earthed
The electrical installation of this towel rail must be carried out by a competent electrician in accordance with the current I.E.E Regulations for Electrical Equipment. The towel rail is suitable for use on an A.C.~ electrical supply. Before installation check that the supply voltage corresponds with that marked on the rail.
IMPORTANT - The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
GREEN/ YELLOW - EARTH
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter
E or by the earth symbol or coloured green or green and yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
This appliance must only be used on A.C. mains supply of 230/240 Volts~.
Installation
If fitted in a room containing a bath or shower, to comply with the current I.E.E. Regulations, a cable outlet will be necessary with the supply to the heater controlled by a double-pole pull-cord switch having a contact separation of 3mm in each pole. The body of the switch should be situated as to be normally inaccessible to a person using a bath or shower. Alternatively the switch can be located outside of the bathroom.
IMPORTANT - Protect the electrical connection whilst handling the towel rail.
The towel rail must be permanently xed to the wall using the wall
brackets supplied.
WARNING - to ensure safe/ correct operation the rail must only be mounted vertically as shown in Fig. 1, observing the minimum clearances stated.
WARNING - The towel rail is heavy. Care must be taken when
lifting and tting the towel rail.
Procedure for wall mounting
Wall mounting dimensions:
Fig. 3
Step 1
Mark suitable mounting hole positions for the xing brackets (ensuring
they are horizontal) - see Fig. 3, ensure to allow enough room above and below to maintain the minimum clearance stated in Fig. 1.
Step 2
Drill and plug (x) the wall to suit. Fix the mounting brackets to the
wall using the screws provided (y). Ensure the bracket pin holes are aligned horizontally to allow the mounting pins to be inserted through the collars - see Fig. 4.
Note: Ensure the mounting brackets are aligned to allow easy assembly of the bracket pins once the towel rail is in place, it is recommended that the pins are inserted towards the adjacent wall (from outside the product) to provide the clearance necessary for the use of tools to secure the rail in place - see Fig. 5.
Step 3
Carefully place the four mounting collars around the towel rail uprights in the positions shown in Fig. 1 and secure in place using xing screws (C) provided - see Fig. 4. ensure the rear of the straps are facing directly backwards.
Wall mounting
The wall mounting accessory pack contains the following:
Fig. 4
Step 4
Lift the towel rail complete with the collars attached and align with
the mounting brackets which were previously xed to the wall. Insert
the collar ends into the mounting brackets and x in place using the
bracket pins (D). The rail is then locked in place by rotating the pins a quarter turn - see Fig. 5.
Fig. 2
Loading...
+ 2 hidden pages