THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Model Description Watts
CDE2TI(B) Switch, Thermostat & Digital Timer Control 2000
CDE2ECC(B) Electronic Climate Control 2000
CDE24ECC(B) Electronic Climate Control 2400
Important Safety Advice
If the appliance is damaged, check immediately
with the supplier before installation and
operation.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience or knowledge if they
have been given supervision or instruction
concerning the use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Children of less than 3 years should be kept
away unless continuously supervised. Children
aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that
it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning
the use of the appliance in a safe way and
understand the hazards involved. Children
aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance
or perform user maintenance.
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
WARNING: This appliance must not be used
in a bathroom.
WARNING: Do not use in areas where petrol,
paint or ammable liquids are used or stored.
DO NOT put objects through the openings of
the appliance. This could lead to functional
faults, possibly to the ignition of the object.
If the mains lead is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualied person in order
to avoid a hazard.
CAUTION: Avoid use of an extension cord
because the extension cord may overheat and
cause risk of re.
The heater carries a warning symbol to
alert the user to the risk of re that exists
if the heater is accidentally covered.
Unplug the heater when not required for long
periods.
WARNING: Do not use this heater in the
immediate surroundings of a bath, a shower
or a swimming pool.
WARNING: This heater must not be located
immediately below a xed socket outlet.
WARNING: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
Note that due care and consideration must be
taken when using this heater in series with a
thermal control, a program controller, a timer
or any other device that switches on the heat
automatically, since a re risk exists when the
heater is accidentally covered or displaced.
General
The heater is designed for operation on an AC electricity supply, and
is suitable for use in domestic dwellings and similar indoor locations.
Always ensure that the appliance is stood on a rm, level base near to,
but not directly beneath, a suitable xed socket outlet.
The heater is tted with wheels, castors and a handle for ease of
movement. Selector switches provide a choice of heat output and an
adjustable thermostat enables the room temperature to be controlled
accordingly. It is supplied with a cord and plug ready for use.
The supply cord should be uncoiled before use (see ‘Storage’).
DO NOT pull the heater along by the mains lead.
Important: The heater must only be operated with the wheels and castors
tted and in the upright position as shown in Fig. 1.
Warning: The heater complies with stringent safety standards but to
ensure efcient operation surfaces of the heater will become hot and
contact with these areas should be avoided, particularly between the air
outlet slots on the top and sides.
The control panel area is designed to be at a far lower temperature to
allow the safe operation of the controls at any time. Momentary contact
with any part of the heater should not cause injury. However aged, inrm
persons or young children should not be left unsupervised in the vicinity
of the heater. Please Note: After switching the heater on for the rst time
and after an extended period of non-use a smell may be noticed, this
is quite normal, the fumes are non-toxic and will quickly disappear. We
recommend that you open a window to ventilate the room when using
the heater during this time. Used in an environment where background
noise is very low, it may be possible to hear a sound which is related
to the element. This is normal and should not be a cause for concern.
Electrical
WARNING: THIS APPLIANCE MUST BE EARTHED
CAUTION: If you use this heater in conjunction with a thermal control,
programme controller, timer or any other device which switches the heater
on automatically observe all safety warnings at all times.
Positioning the Heater
Select the position for the heater ensuring there is clearance from any
furniture and ttings of at least 300mm above the heater and 150mm
each side. The appliance should only be operated on a at stable surface.
Operation
Important – Objects or clothing must not be placed on this heater. Before
using the heater ensure that all warnings and instructions have been
read carefully.
To bring the heater into use plug it in. Neon indicating lights located at
the controls area will glow when the appliance is actually heating.
Controls
On/Off button - This button controls the electricity supply to the
elements. When the On/Off button is activated a neon light ‘x’ illuminates
below the control button.
Thermostat (CDE2TI(B) models only)
The Thermostat (see ‘T’ in Fig. 3) controls the heat output according
to the room temperature. This ensures that the heater will not produce
heat unnecessarily when the room is warm. To set the temperature you
require, turn the thermostat knob clockwise until the required setting is
reached. Alternatively to heat a cold room quickly, turn the thermostat
knob up fully. When the room has reached the desired temperature, turn
the thermostat knob anti-clockwise until the thermostat just clicks off. The
heater will now automatically operate at this temperature. The thermostat
also has a frost protection setting marked ‘’. This setting is useful in
areas such as garages, to prevent frost damage. If the thermostat is set
to its minimum setting ‘’, the heater will cycle on and off to maintain
a temperature of approximately 5° to help protect against frost.
Note: Should the heater fail to come on when the thermostat is at a low
setting, this may be due to the room temperature being higher than the
thermostat setting.
Heat Selector Switches (CDE2TI(B) models only)
Mono and Dual Panel Heat Settings
Selector switches located on the control panel provide a choice of Half
Heat or Full Heat output to suit varying conditions and for economy of
operation.
Half Heat Setting - left hand side - This switch as shown in
Fig. 3 provides half heat output when activated. When it is activated a
neon light ‘x’ illuminates below the control button and the left hand side
element turns on.
Half Heat Setting - right hand side - This switch as shown in
Fig. 3 provides a half heat output when activated. When it is activated
a neon light ‘x’ illuminates below the control button and the right hand
side element turns on.
High Heat Setting - With both switches activated (see Fig. 3)
the maximum output of the heater can be achieved. When both switches
are activated neon lights ‘x’ below each control button illuminate.
Note: The heater will only operate when the On/Off button is activated.
Digital Timer Operation (see ‘z’ in Fig. 3 & Fig. 4)
(CDE2TI(B) models only)
IMPORTANT: Remember to observe all safety warnings when operating
the heater on auto setting, either attended or unattended.
The timer allows you to select ‘AUTO’ or ‘MAN ON’ by pressing the
‘MODE’ button until the required MODE appears at the bottom of the
timer display.
‘MAN OFF’ MODE heat is permanently off. This is also the default screen.
‘MAN ON’ MODE allows power to the heater uninterrupted by the
program settings.
‘AUTO DLY’ switches the heater ON and OFF every day according to
a set daily program.
‘AUTO BLK’ switches the heater ON and OFF according to a set of
programs for weekdays only or weekends only.
Key Lock:
If ‘ENTER’ and ‘MODE’ are pressed within 1 second, the keys will be
locked. The user will know the keys are locked as the lock symbol ‘ ’
will be displayed on the top left hand corner of the screen. To unlock the
keypad, press ‘ENTER’ and then ‘MODE’ within 1 second.
Initial Operation
For initial use, plug the heater into a regular household power point and
turn the power on. The timer is now ready to be set up for use.
Setting Current Time
1. Hold the ‘PROGRAM’ button until the clock symbol appears on the
screen. The user can now set the clock.
2. The hour digit will ash. To adjust the hour use the ‘-’ & ‘+’ buttons.
Conrm the hour digit by pressing ‘ENTER’.
3. Once ‘ENTER’ has been pressed the minutes will ash. To adjust the
minutes use the ‘-’ & ‘+’ buttons. Conrm the minute digit by pressing
‘ENTER’.
4. The timer now returns to the default display.
Once the correct time is set, a total of four ON/OFF time programs can
be set for operation.
Setting Programmes
OPTION 1; Daily (‘DLY’ on display): This is a daily program function,
Monday to Sunday with four ON/OFF program options available.
OPTION 2; Block (‘BLK’ on display): This is a block program function,
Monday to Friday with four ON/OFF program options or Saturday to
Sunday with four ON/OFF program options.
Press the ‘PROGRAM’ key to set the programs starting with ‘Daily
ON’ P1.
SETTING P1 ON TIME:
1. To set the hour use the ‘-’ & ‘+’ buttons. Conrm the hour digit by
pressing ‘ENTER’.
2. To set the minutes use the ‘-’ & ‘+’ buttons. Conrm the minute digit
by pressing ‘ENTER’.
Note: The minutes can only be set in 10 minute blocks in programme
‘MODE’.
SETTING P1 OFF TIME:
3. To set the hour use the ‘-’ & ‘+’ buttons. Conrm the hour digit by
pressing ‘ENTER’.
4. To set the minutes use the ‘-’ & ‘+’ buttons. Conrm the minute digit
by pressing ‘ENTER’.
Repeat steps 1 to 4 to programme P2, P3 & P4. After programming P4
‘OFF’ you automatically exit to the default display.
At any time while programming the timer you can press the ‘PROGRAM’
button to exit to the default display.
Note: If the ‘ON’ time is the same as the ‘OFF’ time the appliance will
ignore the program.
The Advance Function
When in ‘AUTO’ MODE, if the ‘+’ button is pressed for longer than 2
seconds the programme will ADVANCE to the next setting programmed
and will only revert back to the program when the subsequent programme
time is reached. When the ‘ADVANCE’ function is running the ‘ADVANCE’
segment will be displayed on the LCD screen. If the ‘-’ button is pressed
when the ‘ADVANCE’ programme is running the ‘ADVANCE’ feature
will be automatically cancelled and the programme will run as normal.
Note: Timer Memory Back Up Batteries - Once the heater has been left
plugged in with the socket switched on for at least 72 hours the timer’s
memory back up batteries will be fully charged.
Once the timer batteries are fully charged, if there is a power cut or if
the heater is disconnected from the mains for less than six months,
then the timer will continue to keep time & the settings in the memory
will remain intact.
If however the timer back up batteries have not been charged fully,
or if the heater is deprived of power for longer than six months, then
the time and the programme settings are likely to be lost and you may
therefore need to reset the time and the programme before using the
AUTO MODE again.
Electronic Climate Control - see Fig. 2
(CDE2ECC(B) & CDE24ECC(B) models only)
Operation
The electronic control allows MANUAL and AUTO operation.
In MANUALON mode there are three heat settings:
L/H Side Heat, R/H Side Heat and High Heat
In AUTO mode the heater comes on as per the programmed timer
settings (see Setting programs). At any point if the heater is active i.e.
heat is being produced, the ‘ ’ neon is lit - see Fig. 2.
Initial Operation
When the heater is connected to the mains the ‘ ’ neon will be lit and
the display is blank. Press the ‘ ’ button and the display goes to full
heat set to 35oC - see Fig. 7.
Note: All display characters are displayed in Fig. 12.
Standby Mode
With the heater ON if the ‘ ’ button is pressed, the heater will go into
standby mode, heater switches off, the display goes blank and only the
MAINS ON neon ( ) remains lit. On pressing the ‘ ’ button again the
heater will come on in the mode and with the settings it had prior to
going into standby mode.
Setting Time
1. Press and hold ‘ ’ and the clock symbol ‘ ’ appears on the top left
hand side of the screen. The user can now set the time.
2. The hour digit will ash. To adjust the hour use the ‘ ’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘’.
3. The minute digit will ash. To adjust the minute use the ‘ ’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘’. The display
will return to the state before entering set time.
N.B. If no keys are pressed after 4 minutes the display will revert to the
state prior to entering set time.
Manual Operation
Pressing ‘ ’ from the default HIGH screen (Fig. 7) brings the heater
into AUTO mode - see ‘Setting the Timer Programs’. Press again to put
the heater into OFF mode - see Fig. 5. Press again for left hand side
heat ( appears on LCD display - see Fig. 6). Press again for right
hand side heat ( appears on LCD display). Press again brings the
user full circle to FULL heat mode ( appears on LCD display).
Setting the Desired Temperature
The desired temperature can be set using the ‘ ’ or ‘ ’ keys. The
temperature can be set from 5oC to 35oC and this will be shown on the
display. When the temperature is reached the heater will automatically
switch OFF. If the ambient temperature drops the heater will come on
again automatically. Note the electronic climate control device conserves
energy and assists with temperature regulation e.g. if the heater is set
to HIGH heat and the temperature is set to 28oC, at 27oC the heater
will switch to a lower heat setting. Then at 28oC the heater will switch
off completely.
Setting the Timer Programs
Two program settings are possible, P1 and P2. Only high heat is possible
for program settings. Press ‘ ’ once to set the programs, starting with
P1 AUTO ON – See Fig 10.
1. The hour digit will ash. To adjust the hour use the ‘ ’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘’.
2. The minute digit will ash. To adjust the minute use the ‘ ’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘’.
3. Now P1 AUTO OFF is displayed, P1 off time can now be set. Repeat
steps 1 & 2 to set P1 off time.
At this point either:
(a) Press ‘ ’ to exit the Program mode and return to AUTO mode.
The heater is now in AUTO mode. The heater will switch ON and
OFF depending on programme P1 previously entered.
OR
(b) Repeat steps 1 - 3 as above to set the programme for P2.
At this point press ENTER or PROG to exit the Programme mode.
The heater is now in AUTO mode. The heater will switch ON and
OFF depending on programme P1 & P2 previously entered. If after
programming and returning to the AUTO mode display, P1 or P2 is
active, the display will show PROG 1 AUTO ON or PROG 2 AUTO ON
depending on which is active - see Fig. 10. An OFF time cannot be
entered which is less than the corresponding ON time. When setting the
timer programs if no keys are pressed, the display will (after 4 minutes)
revert to the previous display i.e. display prior to entering Program mode.
Run Programs
If MODE is pressed until AUTO appears on the screen (either AUTOON or AUTO-OFF), the heater will run both P1 and P2 program as they
are set.
NOTE: The heater cannot be programmed to run P1 only or P2 only.
To cancel P1, set P1 OFF time to be same as P1 ON time. To cancel P2
set P2 OFF time to be same as P2 ON time.
Review Program settings
To review the program settings the heater must be in AUTO mode. Press
ENTER and the times for PROG 1 ON, PROG 1 OFF, PROG 2 ON and
PROG 2 OFF will be displayed consecutively for 2 seconds. The display will automatically return to the state it was in before ENTER was pressed.
FROST Protection Mode
With the heater in any mode, OFF, MANUAL ON or AUTO, if the
displayed set temperature is reduced to 5oC the heater will go into
FROST Protection mode - see Fig. 11. In this mode only, if the ambient
temperature drops below 5oC, will the heater come on. This is to prevent
freezing. In FROST Protection mode the heater comes on in the high
heat mode only. Pressing the ‘ ’ button is the only way to bring the
heater out of this special mode.
Press the ‘ ’ button on the Remote Control to go from OFF, Man On High and back to OFF again. Press the ‘ ’ or ‘ ’ buttons on the remote
to set desired temperature between 5oC and 35oC. Press the ‘’ button
to put the heater into FROST Protection mode. Pressing the ‘ ’ button
(on the Remote Control) is the only way (using the Remote Control) to
bring the heater out of this mode i.e. pressing the ‘ ’ or ‘ ’ buttons on
the remote will have no effect on the heater.
Discard leaking batteries
Dispose of batteries in the proper manner according to Provincial and
local regulations. Any battery may leak electrolyte if mixed with a different
battery type, if inserted incorrectly, if all the batteries are not replaced at
the same time, if disposed of in a re or if an attempt is made to charge
a battery not intended to be recharged.
Storage
If the radiator is not required for long periods, for example during the
summer, it should be stored in a dry place and preferably covered to
prevent the accumulation of dirt and dust. The plug and cord can be
stored in the storage area provided – see Fig. 14. The cord should be
neatly coiled around the hooks provided and the plug inserted into the
pin-hole in the central compartment.
Safety Overheat Protection
For your safety this appliance is tted with a thermal cut-out. In the
event that the product overheats for some reason, the cut-out prevents
excessive temperatures on the product by cutting the power to the
heater. Once the heater has cooled down, it will reset automatically,
it will continue to cycle on and off automatically until the reason for
overheating is removed.
Cleaning
WARNING - ALWAYS DISCONNECT THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind
on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust
and a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture in to the heater.
After Sales Service
Please see the separate Warranty leaet for details of your Warranty &
after sales service including contact details.
Should you require after sales service, please get in touch with the
supplier through whom you purchased the appliance, or the contract
number on your Warranty leaet.
Remote Control Operation - see Fig. 13
(CDE2ECC(B) & CDE24ECC(B) models only)
The batteries for the remote control are not installed in the remote but
are packed separately in the carton. To install batteries please follow
diagrams behind battery cover on the remote control.
The remote allows the set temperature to be adjusted, the mode to be
selected or can be used to put the heater in FROST Protection mode.
Full Heat output can only be achieved when using the remote control
i.e. both Left hand and Right hand panels are on.