Dimplex 6903950000 User Manual
PRACTICAL USER’S GUIDE
Quality checked by:
FOR THE SAHARA FIREPLACE
Model 6903950000 series
CAT NUMBER:
EWF-SS
Valued Customer,
We are pleased that you have chosen to purchase an electric
fireplace manufactured by Dimplex North America Limited.
7208570100R04
CONTENTS
PAGE 1 Important Instructions
PAGE 4 Fireplace Installation
PAGE 8 Operation
PAGE 10 Remote Operation
PAGE 1 1 Maintenance
PAGE 13 Warranty
QUICK REFERENCE GUIDE FOR THE SAHARA
FIREPLACE
1. Before using the Sahara fireplace verify:
· Are the circuit breakers for the unit
on?
· Are the light bulbs loose? (to
check, follow the instructions for
replacing the light bulbs under the
maintenance section of this
manual)
2. The heater may emit a slight, harmless
odor when first used. This odor is a
normal condition caused by the initial
heating of internal heater parts.
3. The information regarding the model of
your unit can be found on the carton
label or the rating plate. The rating plate
is located on the side of the unit
underneath the outer frame. The carton
label is attached to the front surface of
the carton.
Rating Label
4. If you have any questions or concerns
Serial Number Label
Rating
Label
Serial NumberLabel
regarding the operation of your fireplace,
contact Dimplex customer service at 1888-DIMPLEX (1-888-346-7539).
IMPORTANT INSTRUCTIONS
RETAIN THIS USER’S GUIDE FOR FUTURE
REFERENCE
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons.
1. Read all instructions before using the Sahara
fireplace.
2. The heater is hot when in use. To avoid
burns, do not let bare skin touch hot
surfaces. The trim around the heater outlet
becomes hot during heater operation. Keep
combustible materials, such as furniture,
pillows, bedding, papers, clothes, and
curtains at least 3 feet (0.9m) from the front of
the unit.
3. Extreme caution is necessary when any
heater is used by or near children or invalids
and whenever the unit is left operating and
unattended.
4. Always unplug the Sahara fireplace when not
in use.
5. Do not operate with a damaged cord or plug,
or if the heater has malfunctioned, or if the
Sahara fireplace has been dropped or
damaged in any manner. Return heater to
authorized service facility for examination,
electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. The Sahara fireplace is not intended for use
in bathrooms, laundry areas and similar
indoor locations. Never locate heater where
it may fall into a bathtub or other water
container .
1
8. Do not run the cord under carpeting. Do not
cover cord with throw rugs, runners, or the
like. Arrange cord away from traffic area and
where it will not be tripped over .
9. To disconnect the unit, turn the controls off,
then remove the plug from the outlet.
10.Do not insert or allow foreign objects to enter
any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage
to the heater.
1 1. To prevent a possible fire, do not block air intake
or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may
become blocked.
12. All electrical heaters have hot and arching or
sparking parts inside. Do not use in areas
where gasoline, paint, or flammable liquids are
used or stored or where the unit will be exposed
to flammable vapors.
13. Do not modify the Sahara fireplace . Use it only
as described in this manual. Any other use not
recommended by the manufacturer may cause
fire, electric shock or injury to persons.
14. To reduce the risk of electric shock, this
appliance must be grounded.
Avoid the use of an extension cord. Extension
cords may overheat and cause a risk of fire. If
you must use an extension cord, the cord must
be No. 16 AWG minimum size and rated no
less than 1875 watts.
15. Do not burn wood or other materials in the
Sahara fireplace.
16. Do not strike the glass front.
17. Always use a certified electrician should new
circuits or outlets be required.
18. Always use properly grounded, fused and
polarized outlets.
2
19. Disconnect all power supply before performing
any cleaning, maintenance or relocation of the
unit.
20. When transporting or storing the unit and cord,
keep in a dry place, free from excessive
vibration and store so as to avoid damage
21 If the power supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a
hazard
22 The heater must not be located immediately
below a socket-outlet
SAVE THESE INSTRUCTIONS
NOTE: Procedures and techniques that are considered
important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully
followed, will result in damage to the equipment.
WARNING: Procedures and techniques which, if not
carefully followed, will expose the user to the risk of fire,
serious injury , illness or death.
NOTE
A 15amp, 120 volt circuit is required. A dedicated circuit is
preferred but not essential in all cases. A dedicated circuit
will be required if, after installation, the circuit breaker trips or
the fuse blows on a regular basis when the heater is
operating. Additional appliances on the same circuit may
exceed the current rating of the circuit breaker.
WARNING
Ensure the power cord is not installed so that it is
pinched or against a sharp edge and ensure that the
power cord is stored or secured to avoid tripping or
snagging to reduce the risk of fire, electric shock or
injury to persons.
Construction and electrical outlet wiring must comply
with local building codes and other applicable
3
Loading...