Dimplex 3071, 3072, 3077, 3073, 3078 Installation And Operating Instructions Manual





ContactDetails



Pleasenotethatsomeofthecontactdetailson

thisPDFdocumentmaynotbecurrent.



Pleaseusethefollowingdetailsifyouneedto

contactus:



Telephone:08448793588

Email:[e-mail]




Thecustomersupportsectionofourwebsitealsofeaturesawide
rangeofinformationwhichmaybeofusetoyouandisavailable
24hoursaday.Itincludes:



• Operatingandinstallationinstructions

• Easy‘Howtouse’guidesforstorageheaters

• Serviceandrepairs

• Where

tobuyourproducts

• Literaturedownloads

• Heatingrequirementcalculator


Visit‐www.dimplex.co.uk/support

A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.dimplex.co.uk

Registered No: 1313016 England
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources

Installation and Operating Instructions

Dimplex Convector Heaters

INDCUK307R Issue 4

Models : 3071, 3072, 3073, 3077 and 3078

357

432

MIN

Floor Mtd. Wall Mtd.

230

230

MIN

577 - 2.0kw

697 - 3.0kw

230 156

MIN

450
MIN

Dimensions

(millimetres)

Models Specification

3071 2.0kw Thermostat

3072 2.0kw Thermostat/24hr Timer/Neon

3073 2.0kw Switch/Thermostat

3077 2.0kw 2 Neon Switches/Thermostat/Turbo

3078 3.0kw 2 Switches/Thermostat/Neon

IMPORTANT S FETY ADVICE

3 No. Wall
Mounting
Brackets

floor

520 mm
min.

3

k

w

-

4

7

8

m

m

c

e

n

t

r

e

s

2

k

w

-

3

5

8

m

m

c

e

n

t

r

e

s

526 mm
min.

bracket
slot

shelf /
ceiling

A

WARNING –THIS APPLIANCE MUST NOT BE USED IN A BATHROOM
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY

BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS

ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at the top

of the heater or the air inlet slots in the base of the heater.
The heater carries a warning ‘DO NOT COVER’ to alert the user to the

risk of fire that exists if the heater is accidentally covered.
If young children, the aged or infirm are likely to be left in t he vicinit y

of the heater, we advise that adequate precautions should be taken.­We recommend that a guard be fitted to ensure contact with the
heater is avoided and objects cannot be inserted into the product.

Model 3072 – this model can be set to switch on automatically ,
remember to observe all safety warnings at all times .

If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.

For further information, please contact our guard supplier dir ect on
Tel. No. 01603 667957, or in case of difficulty or for further ad vice
contact the Customer Helpline.

WARNING: In order to avoid a hazard due to inadvertent resetting of
the hrough an thermal cut-out, this appliance must not be supplied t
external o a circuit switching device, such as a timer, or connected t
that is regularly switched on and off by the utility.

WA

rked on

is fitted with

a re replacing the

S 1362

amp plug

ote that
the ollowing
code :

GR
BLUE :
BROWN : LIVE

Connect the GREEN AND YELLOW wire to the terminal marked ‘E’ or by
the earth symbol

, or coloured GREEN or GREEN AND YELLOW.

Connect the BROWN wire to the terminal marked ‘L’ or coloured RED.
Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.

Wall Mounting

Three identical wall mounting brackets are secured to the base of the
heater with a fixing screw. To wall mount appliance, first remove the
brackets as follows :
Lay the heater on its back. Following the sequence in Fig. 1 – identify
and remove the fixing screw securing the brackets located beside Mains
Cable as shown in (a), then pull out brackets and rotate them to
disengage them from the slot (b).
Withdraw the brackets from the slot (c).

(a) (b) (c)

Fig. 1

Select a suitable position on a wall, near to a mains power socket,
making sure that there is at least 230 mm below the heater and at least
450 mm above the heater of unobstructed space. See also ‘Positioning
the heater’.
Fix the two top retaining brackets to the wall, using suitable fixings, for
2kw models at 358 mm centres and 3kw models at 478 mm centres –
see Fig 2.

Fig. 2

Locate the heater on the top brackets and allow it to hang in place.
Fit the bottom bracket into the slot in the heater and then fix it to the wall.

Test that the heater is now securely fixed to the wall.

Electrical connection

RNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an ~ supply only and the voltage ma
the heater must correspond to the supply voltage. This heater

wirable plug incorporating a 13 amp fuse. In the event of
fuse in the plug supplied, a 13 amp fuse approved by ASTA to B
must be used. If any other type of plug is used, a 15 amp fuse must be
fitted in the plug, the adaptor, or at the distribution board.
IMPORTANT : If the plug is not suitable for your socket, the 13
should be removed. Before wiring the appropriate plug, please n

wires in this mains lead are coloured in accordance with the f

EEN AND YELLOW : EARTH

NEUTRAL

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.