Built-in Warming Drawer
W 200SSS
W 200BBS
D
D
Installation and Operating Manual
CONTENTS
Important Notes -------------------------------------------------------------------------------------Page 2
Installation Instructions ---------------------------------------------------------------------------Page 3
Technical Specification ----------------------------------------------------------------------------Page 4
Warming Drawer Overview ------------------------------------------------------------------------Page 4
Control Panel ----------------------------------------------------------------------------------------Page 5
Cookware Safety ------------------------------------------------------------------------------------Page 6
Cleaning and Maintenance ------------------------------------------------------------------------Page 6
Troubleshooting -------------------------------------------------------------------------------------Page 7
Important Notes
Dear Customer
Thank you for choosing our product. This appliance is easy to use; however please read this
handbook carefully before installing and operating it. Herein, you will find the correct
method of installation and tips for best use and maintenance of the product.
This appliance is designed to be handy for any adult to use at home. Do not allow
children to play with it. Children need to be supervised when the product is in operation
so that they do not go near the drawer and touch the hot surfaces.
This product must be connected in accordance with current electrical regulations. A
fixed wiring installation is to be done only by an authorized electrician.
Before maintenance or cleaning of the product, disconnect the appliance from the
mains and wait for the oven to cool down first.
For any repairs, always contact authorized Customer Service Center and ask for original
spare parts. Repairs by untrained people may lead to damage and void the warranty.
THE APPLIANCE MUST BE CONNECTED IN ACCORDANCE WITH CURRENT ELECTRICAL RULES
AND REGULATIONS. INSTALLATION IS TO BE DONE ONLY BY AN AUTHORIZED ELECTRICIAN.
WARNING: THIS APPLIANCE MUST BE EARTHED
Before connecting to the mains, make sure that:
The supply system is regularly earthed, according to the regulations in force.
The isolation switch can easily be reached after the oven is installed.
After connection to the mains, check that the supply cable does not overheat.
Never use reductions, shunts, adaptors that can cause overheating or burning.
The manufacture shall not liable for any direct or indirect damage caused by faulty
installation. The installer must ensure that the product installation and connection
complies with the local and general regulation in force.
l
l
l
l
l
l
l
l
l
Power Connection:
Means for disconnection must be incorporated in the fixed wiring in accordance with the
wiring rules.
V 1.0 Page 2
Installation Instruction
Product & cutout dimensions for
WD200SSS
WD200BBS
l
l
l
l
l
l
l
Fit the appliance into its cabinetry by inserting screws into the 4 holes that can be seen in the frame
of the warming drawer when the door is open.
The warming drawer needs a supporting surface underneath. The sides and the face surface where
the warming drawer is to be installed should be milled to allow sufficient air intake and circulation
around the oven, to avoid causing any damage to the furniture.
Ensure the oven in secured firmly in place as described above, and insulate electrical connections in
order to avoid contact with metallic parts. The adhesive joining the rolled sections to the cabinet
has to withstand temperatures no lower than 90 to avoid deformations or instability.
For the most efficient air circulation, the warming drawer should be fitted according to the
dimensions shown. The rear panel of the cabinet must be removed so that air can circulate freely.
The panel to which the warming drawer is fitted should have a gap of at least at the rear.
The warming drawer should be installed in a position which is at least 20mm away from other heating
appliances.
Do not switch on the appliance before it has been fully and correctly installed.
WARNING: The power socket must be connected to a switch with earth leakage protection. If the power
cable is damaged, please contact a qualified electrician for replacement.
Remove the special film covering the warming drawer door glass (if there is any)
Heat the empty warming drawer at max. temperature for 45 minutes. This is to remove any
unpleasant smell caused by working residues.
℃
80 - 90 mm
Before using the warm ing drawer, we suggest to:
V 1.0 Page 3
Installation Rubber
4X29 self tapping screw
Technical Specification
Warming Drawer Overview
This product is a full extension telescopic drawer.
Control Panel
Product Bulit-in Warming Drawer
Voltage / Frequency 220-240Vac / 50Hz
Heating Element Rated Power 500 W
Ventilation Motor Rated Power 15 W
Temperature Range 35-75°C (Adjustable)
Model Number WD200SSS / WD200BBS
Timer 120 min
Max Load 20 kg
Capacity 9 place settings
Rater Power 515 W
Net Weight 16 kg
Product Dimension 597 x 530 x 197 mm
V 1.0 Page 4
Control Panel
Indication
Warming Timer
Temperature Setting
Note: Do not overload the drawer. The maximum load bearing capacity of the drawer is
20kg.
The green light is illuminated to show the appliance is powered on and is on standby. The
yellow light is illuminated to show the warming drawer is in operation mode.
Turn clockwise to set the warming timer from 0 to maximum 120minutes. Turn
anticlockwise to set the appliance to work continuously.
Temperature can be set by turning the knob from 35 to 75°C
Indicator Light
Green to indicate
power on
Yellow to indicate
warming drawer
is in operation
mode
Indicator Light
Temperature
adjustment knob
Turn cloc kwi se
to set temperature
Timer
Turn clockwise to
set the timer from
0 to 120minutes
Turn anticlockwise
to enable warming
drawer to work
continuously.
Symbol :
V 1.0 Page 5
0
30
60
90
120
Min
℃
0
25
50
75
Cookware Safety
Cleaning and Maintenance
Plastic containers or plastic wrap can melt if in direct contact with the drawer or a hot utensil. If it melts
onto the drawer, it may not be removable.
Do not place plastic cutleries or bottles which have a melting point below 100°C into the drawer. Use
heat-safe dishes only.
The built-in warming drawer is not intended for use by young children or infirmed persons without
supervision.
Children and pets should not be left alone or unattended in the area where the appliance is in use. They
should never be allowed to play in its vicinity, whether or not the appliance is in use.
: Prior to cleaning or maintenance, always disconnect the power supply. Clean the warming
drawer after it cools down.
Clean the water spots or scale after use.
Wipe and clean the drawer interior with sponge or cloth from time to time.
The warming drawer will keep hot, cooked foods at serving temperature. Always start with hot food.
use it to heat cold food with the exception of proofing yeast dough, crisping crackers, chips,
dry cereal or warming dishes or plates.
Child Safety
Caution
Make sure a steamer cleaner is not used.
Warning: Do not use harsh chemicals or cleaning agents or any abrasive material for cleaning purpose.
Under no circumstances use a steam cleaning appliance to clean this appliance. The steam could attack
the electrical components and cause a short circuit.
Warning:
1. Accessible parts may become hot during use. Young children should be kept away.
2. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the warming drawer door glass
since they can scratch the surface, which may result in shattering of the glass.
3. Steam cleaner i s not to be used.
4. Fixed wiring must be protected.
5. Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring
rules.
6. When it is in use the appliance becomes hot. Care should be taken to avoid touching heating
elements inside the oven
7. Surfaces of the warming drawer can get hot.
8. This product must not be disposed with the domestic waste. It has to be disposed at an authorised
bin for recycling the appliances.
9. This appliance is not intended for use by a person (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been given
supervision or instruction regarding the use of appliance by personnel who is responsible for their
safety.
10. Always make sure the knobs are in the “0” position when the appliance is not in use.
DO NOT
.
V 1.0 Page 6
Troubleshooting
NOTE: The maintenance and service must be carried by qualified service person. Repairs
and other work by unqualified persons could be dangerous.
The manufacturer is not liable for any direct or indirect damage caused by unqualified
service person or installer.
Scenario Possible Causes Solution
Indicator light does not
function
Power is not switched on Turn the warming drawer
power on
Loose connection Contact the service
representative
Warming drawer fails to
heat up
Heating element damage Contact the service
representative
Ventilation fails Ventilation motor damage Contact the service
representative
Circuit Diagram
Thermo Cutout
Timer
Fan
Thermostat
Fuse
Heating Element
Power
Indicator light
Operating
Indicator Light
V 1.0 Page 7
Loading...