Diglo Safeguard Supply WC180-SS Wireless Flashing Strobe Doorbell Kit - USER MANUAL User Manual

Remar ks :

(1)Pairing mode will timeout automatically after pairing is completed.
(2)Pairing mode will last for 5 seconds only.

Two or more transmitters pairing:

Only one transmitter can be programmed at a time. For additional

transmitters, please follow the pairing steps (1)-(3) once again to pair
the transmitters one by one.

It is common practice to choose a different ringtone for each
transmitter so you can distinguish which transmitter is being
triggered.

Factory Reset:

Hold the Music Change button for approximately 5 seconds. You
will hear a short ‘Ding Dong’ ringtone and a quick flash of the LED

strobe light. This indicates the receiver has reset to factory settings

which is no transmitter paired and the receiver set to the "Ding­Dong" sound.

Changing the Ringtone:
Refer to Step 3 in the "Quick Start" section of this manual.

4

WC180-SS

WIRELESS DOORBELL KIT

User Manual

Pleas e ca ref ul ly r ead t hi s us er ma nu al b efo re u si ng an d in st all at io n

WC180-SS Receiver & Transmitter Installation

Important: Test the range before mounting the push button (or other

compatible sensor). The sensor will be referred to as a
"transmitter" in this document. The options below are for a push

button. If using a different transmitter type, consult that manual.

Transmitter Installation Method 1: Double-sided adhesive tape.
(Easiest install method)

1.After ensuring the right mounting position, please clean the flat area
where you intend to install transmitter.

2.Tear off one side of the double-sided adhesive tape and stick it to
the underside of transmitter; tear off the other side and place the
transmitter on the wall. Hold in place for 10 seconds.

Transmitter Installation Method 2: Screw/Anchors
Please prepare an electric drill, Phillips screwdriver and slotted
screwdriver before installation.

1.Use the small screwdriver to separate the top half of the case
from the lower half of the cases.

2.Using the back half of the case as a template, make two marks
on the wall where the pre-drilled holes are located.

3.Drill two holes on the marked places, then insert the wall
anchors (if needed).

4.Use the supplied screws to secure the back half of the push
button to the wall.

5.Snap top half of push button cover to lower half.

5

What You S ho ul d Kn ow B ef or e Us in g

1.The transmitter (push button) supplied with this kit comes paired with
the receiver from the factory, set to default ringtone “Ding-Dong”. If you
are only using the push button included with this kit and are okay with
the "Ding-Dong" ringtone, then there is no programming/pairing
required.

2.IF NOT, please refer to the “Quick Start” section to pair the
transmitter with the receiver and set your favorite ringtone(s).

3.It is not advisable to mount the transmitter onto metal surfaces as it
will diminish or block RF signals between the transmitter and the

receiver. However, if this is the only option then we recommend that
you use the double sided tape provided for mounting the push button.

4.Operating range will decrease if battery in transmitter is in low power
status.

5.It is not advisable to mount the transmitter in the outdoor directly
without any shelter which could accelerate aging of plastic materials.

1 2 3

Troubleshooting

Troubleshooting

1.The r ec eiv er d oe sn’ t so un d

Ÿ Check the doorbell button battery, replace it if necessary.
Ÿ The receiver is not securely set into the outlet .
Ÿ The receiver could be out of range of the doorbell button.
Ÿ The receiver may not have paired with the doorbell button.
Ÿ Ensure the volume is not muted (press volume button).

2.Ope ra tin g ra ng e is re du ce d

Ÿ Metal structures can reduce the range of the product. Avoid

mounting the push or chime on or near metal structures.

Ÿ Other equipment can cause radio interference that affects your

doorbell.

Ÿ Walls and ceilings will reduce the range.
Ÿ Weak batteries will reduce range. Replace every 12–18 months.

6

Quick Start

Volume Control

Music C ha nge

1. Volume Control Button Location: Press the Volume Control
button on the receiver. Press the button to toggle between High and
Low volume and mute.

*The volume level setting does not affect the strobe light.

2. Set Ringtone Using the Music Change Button: Press the
Music Change button to choose your favorite ringtone. Stop

pressing the button once you hear the ringtone you want to use.

Warranty Info & Contact Information

This product is warranted for 1 year by Safeguard Supply. Please
consult the Safeguard Supply website at safeguardsupply.com/
warranty-policy for additional information.

To contact us:

Safeguard Supply

• [e-mail]

• 800-366-7235

For warranty information, visit: https://safeguardsupply.com/
warranty-policy
For FCC Information, visit: https://safeguardsupply.com/fcc



3.Pairing a transmitter to the receiver:

(1) Select the ringtone you want to
associate with the transmitter.

Selec t ri ngt on e

(2)Hold and press the Volume Control

button for 5s until a “Ding-Dong” sound
is heard and the LED strobe starts
flashing. The receiver is now in paring
mode.

Hold Vol ume C ha ng e for 5 s

(3) Push the center push on the push
button (or other transmitter) to send a
signal to the receiver.

Press the button