Page 1
Visit_001ART011-EN
Visit push button transmitter
Buttons and connections
Status LED
Radio key switches Hole for lanyardFront button
Signal switches
BE1420
Technical specications
In the box
BE1420 Visit push button transmitter
with pre-mounted PX28G/PX28M
6V alkaline battery
Lanyard with safety clasp
Adhesive tape, screws and plugs
Power and battery
Battery type
16 V PX28G/PX28M alkaline or
16 V PX28L lithium
Power consumption
Active < 35 mA
Idle position < 0.05 μA
Operation time
Alkaline battery ~ 2 years
Lithium battery ~ 5 years
Pre-mounted battery
Dimensions and weight
Height: 66 mm, 2.6"
Width: 48 mm, 1.9"
Depth: 23 mm, 0.9"
Weight: 50 g, 1.8 oz. incl. battery
Activation
Via the front button
Environment
For indoor use and outdoor use
in a protected location. Will not
withstand water or rain. (IP42)
Operating temperature
-10° to 40° C, 14° to 104° F
Relative humidity
15% to 90%, non-condensing
Adhesive tapeFront cover
Frequency and coverage
Frequency: 315 MHz, 433.92 MHz or
868.3 MHz, depending on region
Coverage by region:
315 MHz: Up to 50 m (164 ft)
433 MHz: 30 – 80 m (98 - 260 ft)
868 MHz: 50 – 250 m (55 - 273 yd)
Coverage depends on the radio
frequency, building’s characteristics
and the combination of transmitters
and receivers.
Maintenance and cleaning
Maintenance free
Clean with a dry cloth
Do not use household cleaners,
aerosol sprays, solvents, alcohol,
ammonia or abrasives
2hole markings
Page 2
Visit push button transmitter
Visit_001ART011-EN
Using it as a caller button
The transmitter can be worn around your neck and
be used as a wireless caller button.
Here is how you use it:
1 Attach the lanyard to the transmitter.
A B
2 Hang the transmitter around your neck.
Using it as a doorbell
The transmitter can also be used as a wireless doorbell. Here is how you set it up:
Mounting with screws
1 Carefully remove the transmitter front cover and make two holes on the markings.
2 Fix the unit to the wall using the supplied screws and put the cover back on.
1 2
21
Mounting with adhesive tape
1 Attach the adhesive tape to the back of the transmitter.
Clean the wall with the wet wipe and remove the protective lm from the tape.
2 Mount the unit in a weather protected area by the front door.
1
www.bellman.com
Bellman Visit 868 Pushbutton transmitter
Model: BE1420
Frequency 868,3 MHz
Battery: 1 x 6V
Made in P.R.C. by Bellman & Symfon AB, Sweden
2
Page 3
Visit push button transmitter
Visit_001ART011-EN
Testing the connection
Using the front button
1 Press the front button on the transmitter. The LED lights up
in green to show that a radio signal is being transmitted.
2 The green Visit LED on the receiver lights up to show that
the signal was received. In addition, it starts to sound, ash
or vibrate with a certain pace, called signal pattern.
The transmitter determines the signal pattern and the
default is as follows:
1 2
Default signal pattern
Transmitter Receiver signal pattern
LED LED Sound Vibration Flash
Green light Green light 1door chime, low Slow Yes
Changing the signal pattern
Changing the signal pattern is easy. Just open the transmitter front cover and move signal switches
no. 8, 9 and 0 according to the table below:
On
O
Transmitter Receiver signal pattern
Switch LED Sound Vibration Flash
Green light 1door chime, low Slow Ye s
2green blinks 2door chime, low Slow Ye s
3green blinks 1door chime, high Slow Ye s
Green blinks 2door chime, high Slow Ye s
Orange light Baby melody Fast Yes
Orange blinks Baby melody Fast Yes
Yellow light 1ring signal, low Medium Yes
Yellow blinks 2ring signal, high Medium Ye s
Page 4
Visit push button transmitter
Changing the radio key
If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio
interference you need to change the radio key on all units. The radio key switches are located under the transmitter cover.
Here is how you change the radio key:
Visit_001ART011-EN
1 Remove the transmitter front cover and move any radio key switch to the up (on position)
to change the radio key. By default, all radio key switches are positioned down (o).
2 Press and hold the test/function button on the receiver until the green and yellow Visit LEDs
blink alternately. Release the button.
3 Press the front button on the transmitter within 30 seconds to send the new radio key.
4 All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. It then returns to normal mode.
Note: All Visit units must be set to the same radio key in order to operate as a group.
1 2 3
On
O
RADIO KEY
4
5
RADIO KEY SIGNAL
Troubleshooting
If Try this
The transmitter LED lights up in yellow
when I press the button
The transmitter LED doesn’t light up
when I press the button
The transmitter LED lights up in green
but the receiver is not activated
The receiver is activated for no
apparent reason
The battery is nearly depleted. Replace it with an alkaline PX28A or a lithium
PX28L type battery.
Check that the battery is positioned correctly.
Replace the battery with an alkaline PX28A or a lithium PX28L type battery.
Check the receiver batteries and connections.
Move the receiver closer to the transmitter to make sure it’s within radio range.
Check that the units are set to the same radio key, see Changing the radio key.
There is probably another Visit system installed nearby that triggers your
system. Change the radio key on all units, see Changing the radio key.
Loading...