Digitus Wireless Internet Broadband Router User Manual

1
USER MANUAL
2
Introduction....................................................................................................................... 4
Features.............................................................................................................................. 4
Minimum Requirements.................................................................................................. 4
Package Content ............................................................................................................... 4
Note .................................................................................................................................... 4
Get to know the Broadband Router................................................................................ 5
Back Panel........ ........................................................................................................... .. .... 5
Front Panel........................................................................................................................ 6
Setup Diagram...................................................................................................................7
Getting started...................................................................................................................8
Chapter 1.........................................................................................................................16
Quick Setup.....................................................................................................................16
Step 1) Time Zone...........................................................................................................16
Step 2) LAN Interface..................................................................................................... 16
Step 3) WAN Interface...................................................................................................17
1.31 Static IP.................................................................................................................... 18
1.32 DHCP Client............................................................................................................19
1.33 PPPoE ......................................................................................................................20
1.34 PPTP ........................................................................................................................ 21
Step 4) Wireless Basic Settings...................................................................................... 23
Step 5) Wireless Security Settings.................................................................................24
1.51 WEP .........................................................................................................................25
1.52 WPA(TKIP).............................................................................................................26
1.53 WPA2(AES).............................................................................................................28
1.54 WPA2 Mixed........................................................................................................... 29
Chapter 2.........................................................................................................................31
General Settings.................................. .. .......................................................................... 31
2.1 System........................................................................................................................33
2.1.1 Time Zone Setting..................................................................................................34
2.1.2 Password Setup.......................................................................................... ............ 34
2.2 WAN.................................................... .......................................................................36
2.2.1 Static IP...................................................................................................................37
2.2.2 DHCP Client...........................................................................................................37
2.2.3 PPPoE (PPP over Ethernet)........................................................... ... .................... 37
2.2.4 PPTP ..................................... ...................................... ............................................ 37
2.2.5 DDNS....................................................................................................................... 37
.... 38
2.4 Wireless............................... ..................................... ...................................... ............ 40
2.4.1 Basic Settings................................................................ ...................................... .... 40
2.4.2 Advanced Settings.............................................................. .. ..................................42
2.4.3 Security................................................. ..................................................................44
2.4.4 Access Control............................................................ .. .......................................... 45
2.4.5 Site Survey....................................................... ....................................................... 46
2.4.6 WDS Settings................................................................ ... ..................................... ..47
2.5 Firewall.................................................... ... ..................................... .......................... 49
2.5.1 Port Filtering........................................................ ... ..................................... .......... 50
3
2.5.2 IP Filtering............................................................................................ ... ...............51
2.5.3 MAC Filtering................................................................. ..................................... ..52
2.5.4 Port Forwarding ........................................ .. ...................................... .................... 53
2.5.5 DMZ........................................................................................................................ 54
Chapter 3.........................................................................................................................56
Status ................................................................................................................................56
3.1 Status................................................................ .......................................................... 57
3.2 System Log..................................................................... ............................................ 57
3.3 Statistics................................................................... .................................................. 59
Chapter 4.........................................................................................................................60
Tool................................................................................................................................... 60
4.1 Save/Reload Settings.................................................................. ... ............................61
4.2 Firmware Upgrade ....................................... .. ...................................... .................... 62
Appendix A......................................................................................................................63
Glossary .........................................................................................................................64
4
Introduction
Congratulations on purchasing this Wireless Broadband Router. This Wireless Broadband Router is a cost-effective IP Sharing Router that enables multiple users to share the Internet through an ADSL or cable modem. Simply configure your Internet connection settings in the Wireless Broadband Router and plug your PC to the LAN port and you're ready to share files and access the Internet. As your network grows, you can connect another hub or switch to the router’s LAN ports, allowing you to easily expand your network. The Wireless Broadband Router is embedded with a IEEE 802.11g/b access point that allows you to build up a wireless LAN. The Wireless Broadband Router provides a total solution for the Small and Medium-sized Business (SMB) and the Small Office/Home Office (SOHO) markets, giving you an instant network today, and the flexibility to handle tomorrow's expansion and speed.
Features
High Internet Access throughput (50M)
Allow multiple users to share a single Internet line
Supports up to 253 users
Internet Access via Cable or xDSL modem
Access Private LAN Servers from the Public Network
Equipped with four LAN ports (10/100 M ) and on e WA N port (1 0 / 10 0M)
Provides IEEE 802.11g/b wireless LAN access point
Support DHCP (Server/Client) for easy setup
Support advance features such as: Special Applications, DMZ, Virtual Servers, Access
Control, Firewall.
Allow you to monitor the router’s status such as: DHCP Client Log, System Log, Security Log and Device/Connection St atu s
Easy to use Web-based GUI for configuration and management purposes
Remote Management allows configuration and upgrades from a remote site (over the
Internet)
Minimum Requirements
One External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45)
Network Interface Card (NIC) for each Personal Computer (PC)
PCs with a Web-Browser (Internet Explorer 4.0 or higher, or Netscape Navigator 4.7 or
higher)
Package Content
One 4-port Broadband router unit
One Quick Installation Guide
One User Manual CD
One Power Adapter
Accessories
Note
The WAN “idle timeout” auto-disconnect function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly when you use this function in the first time, especially your ISP charge you by time used.
5
Get to know the Broadband Router
Back Panel
The diagram (fig1.0) below shows the broadband router’s back panel. The router’s back panel is divided into three sections, LAN, WAN and Reset:
Figure 1.0
1) Local Area Network (LAN) The Broadband router’s 4 LAN ports are where you connect your LAN’s PCs, printer servers,
hubs and switches etc.
2) Wide Area Network (WAN)
The WAN port is the segment connected to your xDSL or Cable modem and is linked to the Internet.
3) Reset
The Reset button allows you t o do one of two things.
1) If problems occur with your router, press the router’s reset button with a pencil tip (for
less than 4 seconds) and the router will re-boot itself, keeping your original configurations.
2) If problems persist or you experience extreme problems or you forgot your password,
press the reset button for longer than 4 seconds and the router will reset itself to the factory default settings (warning: your original configurations will be replaced with the factory default settings)
6
Front Panel
On the router’s front panel there are LED lights that inform you of the router’s current status. Below is an explanation of each LED and its description.
LED Light Status Description
PWR ON Router’s power supply is on WAN 10/100M ON WAN port 100Mbps is connected
OFF WAN port 10Mbps is connected WAN LNK/ACT ON WAN is connected OFF No WAN connection Flashing WAN port has Activity (ACT), data being sent
LAN 10/100M ON LAN port 100Mbps is connected (Port 1-4) OFF LAN port 10Mbps is connected LAN LNK/ACT ON LAN is connected (Port 1-4) OFF No LAN connection
Flashing LAN port has Activity (ACT), data being sent
WLAN-G ON Wireless LAN has been activated OFF Wireless LAN is disabled Flashing Wireless LAN has Activity (ACT) data being sent
7
Setup Diagram
Figure 1.2 below shows a typical setup for a Local Area Network (LAN).
Figure 1.2
8
Getting started
This is a step-by-step instruction on how to start using the router and get connected to the Internet.
1) Setup your network as shown in the setup diagram above (fig 1.2).
2) You then need to set your LAN PC clients so that it can obtain an IP address automatically.
All LAN clients require an IP address. Just like an address, it allows LAN clients to find one another. (If you have already configured your PC to obtain an IP automatically then proceed to step 3, page 11)
Configure your PC to obtain an IP address automatically
By default the broadband router’s DHCP is on, this means that you can obtain an IP address automatically once you’ve configured your PC to obtain an IP address automatically. This section will show you how to configure your PC’s so that it can obtain an IP address automatically for either Windows 95/98/Me, 2000 or NT operating systems. For other operating systems (Macintosh, Sun, etc.), follow the manufacturer’s instructions. The following is a step-by-step illustration on how to configure your PC to obtain an IP address automatically for 2a) Windows 95/98/Me, 2b) Windows XP, 2c) Windows 2000 and 2d)
Windows NT.
2a) Windows 95/98/Me
1: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2: Double-click Network icon. The Network window will appear. 3: Check your list of Network Components. If TCP/IP is not installed, click the Add button to
install it now. If TCP/IP is installed, go to step 6. 4: In the Network Component Type dialog box, select Protocol and click Add button. 5: In the Select Network Protocol dialog box, select Microsoft and TCP/IP and then click the
OK button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation.
6: After installing TCP/IP, go back to the Network dialog box. Select TCP/IP from the list of Network Components and then click the Properties button.
7: Check each of the tabs and verify the following settings:
Bindings: Check Client for Microsoft Networks and File and printer sharing for Microsoft Network s.
Gateway: All fields are blank.
DNS Configuration: Select Disable DNS.
WINS Configuration: Select Disable WINS Resolution.
IP Address: Select Obtain IP address automatically.
9
8: Reboot the PC. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3
2b) Windows XP
1: Click the Start button and select Settings, then click Network Connections. The Network
Connections window will appear.
2: Double-click Local Area Connection icon. The Local Area Connection window will
appear.
3: Check your list of Network Components. You should see Internet Protocol [TCP/IP] on
your list. Select it and click the Properties button.
4: In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address
automatically and Obtain DNS server address automatically as shown on the following screen.
10
5: Click OK to confirm the setting. Your PC will now obtain an IP address automatically
from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
2c) Windows 2000
1: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2: Double-click Network and Dial-up Connections icon. In the Network and Dial-up
Connection window, double-click Local Area Connection icon. The Local Area Connection window will appear.
3: In the Local Area Connection window, click the Properties button. 4: Check your list of Network Components. You should see Internet Protocol [TCP/IP] on
your list. Select it and click the Properties button. 5: In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address
11
automatically and Obtain DNS server address automatically as shown on the following screen.
6: Click OK to confirm the setting. Your PC will now obtain an IP address automatically
from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
2d) Windows NT
1: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2: Double-click Network icon. The Network window will appear. Select the Protocol tab from the Network window.
3: Check if the TCP/IP Protocol is on your list of Network Protocols. If TCP/IP is not installed, click the Add button to install it now. If TCP/IP is installed, go to step 5.
4: In the Select Network Protocol window, select the TCP/IP Protocol and click the Ok
12
button to start installing the TCP/IP protocol. You may need your Windows CD t o complete the installation.
5: After you install TCP/IP, go back to the Network window. Select TCP/IP from the list of Network Protocols and then click the Properties button.
6: Check each of the tabs and verify the following settings:
IP Address: Select Obtain an IP address from a DHCP server.
DNS: Let all fields are blank.
WINS: Let all fields are blank.
Routing: Let all fields are blank.
7: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
13
3) Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will automatically give your LAN clients an IP address. By default the Broadband Router’s DHCP server is enabled so that you can obtain an IP address automatically. To see if you have obtained an IP address, see Appendix A.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN. If there is another DHCP on your network, then you’ll need to switch one of the DHCP servers off. (To disable the Broadband router’s DHCP server see chapter 2 LAN Port)
4) Once your PC has obtained an IP address from your router, enter the default IP address
192.168.2.1 (broadband router’s IP address) into your PC’s web browser and press <enter>
5) The login screen below will appear. Enter the “User Name” and “Password” and then click <OK> to login.
Note: By default the user name is “admin” and the password is “1234”. For security reasons it is recommended that you change the password as soon as possible (in General setup/system/password, see chapter 2)
6) The HOME page screen below will appear. The Home Page is divided into four sections,
Quick Setup Wizard, General Setup, Status Information and Tools. Quick Setup Wizard (Chapter 1)
If you only want to start using the broadband router as an Internet Access device then you ONLY need to configure the screens in the Quick Setup Wizard section.
General Setup (Chapter 2)
14
If you want to use more advanced features that the broadband router has to offer, then you’ll need to configure the Quick Setup Wizard and the General Setup section. Alternatively, you can just configure the General Setup section, since the General Setup/WAN and the Quick Setup Wizard contain the same configurations.
Status Information (Chapter 3) The Status Information section is for you to monitor the router’s current status information only.
Tools (Chapter 4) If you want to Reset the router (because of problems) or save your configurations or upgrade the firmware then the Tools section is the place to do this.
Menu Description
Quick Setup Wizard (Chapter 1)
Select your Internet connection type and then input the configurations needed to connect to your Internet Service Provider (ISP).
General Setup (Chapter 2)
This section contains configuratio ns for the Broadband router’s advance functions such as:
Address Mapping, Virtual Server, Access Control, Hacker Attack Prevention, DMZ, Special applications and other functions to me et your LAN requirements.
15
Status Information (Chapter 3) In this section you can see the Broadband
router's system information, Internet Connection, Device Status, System Lo g, Security Log and DHCP client information.
Tools (Chapter 4)
This section contains the broadband router’s Tools - Tools include Configuration too ls, Firmware upgrade and Reset. Configuration tools allow you to Backup (save), Restore, or Restore to Factory Default configuratio n for you r Broadband router. The Firmware upgrade tool allows you to upgrade your Broadband router's firmware. The RESET tool allows you to reset your Broadband router.
7) Click on Quick Setup Wizard (see chapter 1) to start configuring settings required by your ISP so that you can start accessing the Internet. The other sections (General Setup, Status Information and Tools) do not need to be configured unless you wish to implement/monitor more advance features/information.
Select the section (Quick Setup Wizard, General Setup, Status Information and Tools) you wish to configure and proceed to the corresponding chapter. Use the selections on the web management’s top right hand page (see below) to navigate around the web-based management User Interface.
16
Chapter 1
Quick Setup
The Quick Setup section is designed to get you using the broadband router as quick as possible. In the Quick Setup you are required to fill in only the information necessary to access the Internet. Once you click on the Quick Setup Wizard in the HOME page, you should see the screen below.
Step 1) Time Zone
The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as Log entries and Firewall settings.
Parameter Description
Enable NTP client update Check this box to enable the auto time synchronization
function. The router will set its time based on your selection.
Time Zone Select You can select your local time zone here. The router
will sync time according to your time zone selection.
NTP server Select the time server to synchronize with.
Click on NEXT to proceed to the next page (step 2) LAN Interface.
Step 2) LAN Interface
The LAN Interface settings allow you to configure the parameters for local area network.
17
Parameter Description
IP Address This is the router’s LAN port IP address (Your LAN
clients default gateway IP address)
Subnet Mask Specify a Subnet Mask for your LAN segment.
Click on NEXT to proceed to the next page (step 3) WAN Interface.
Step 3) WAN Interface
In this section you have to select one of four types of connections that you will be using to connect your broadband router’s WAN port to your ISP (see screen below).
Note: Different ISP’s require different methods of connecting to the In ternet, please check with your ISP as to the type of connection it requires.
18
Menu Description
1.31 Static IP
Your ISP has given you an IP address already
1.32 DHCP Client Your ISP will automatically give you an IP address
1.33 PPPoE Your ISP requires you to use a Point-to-Point Protocol over
Ethernet (PPPoE) c onnection.
1.34 PPTP
Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection.
Select one of the WAN types and set the manual’s relevant sub-section (1.31, 1.32, 1.33, or 1.34). Click on Back to return to the previous screen.
1.31 Static IP
Select Static IP if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information required in this section.
19
Parameters Description
IP Address
This is the IP address that your ISP has given you.
Subnet Mask Enter the Subnet Mask provided by your ISP
(e.g. 255.255.255.0)
Default Gateway IP
This is the ISP’s IP address gateway
DNS This is the ISP’s DNS server IP address
Click on NEXT to proceed to the next page (step 4) Wireless Basic Settings.
1.32 DHCP Client
Choose DHCP Client if your ISP will automatically give you an IP address.
20
Click on NEXT to proceed to the next page (step 4) Wireless Basic Settings.
1.33 PPPoE
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required in this section.
21
Parameter Description
User Name
Enter the User Name provided by your ISP for the PPPoE connection
Password
Enter the Password provided by your ISP for the PPPoE connection
Click on NEXT to proceed to the next page (step 4) Wireless Basic Settings.
1.34 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in this section.
22
Parameter Description
IP Address
This is the IP address that your ISP has given you to
establish a PPTP connection.
Subnet Mask
Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0)
Server IP Address
Enter the IP address of the ISP Gateway
User Name
Enter the User Name provided by your ISP for the PPTP connection. Sometimes called a Connection ID
Password
Enter the Password provided by your ISP for the PPTP connection
Click on NEXT to proceed to the next page (step 4) Wireless Basic Settings.
23
Step 4) Wireless Basic Settings
Wireless Access Point bui ld s a wireless LAN and can let a ll PCs equipped with IEEE
802.11b or 801.11g wireless network adaptor connect to your Intranet. It supports WEP
and WPA2 encryption to enhance the security of your wireless network.
Menu Description
Band It allows you to set the AP fix at 802.11b or 802.11g mode.
You also can select B+G mode to allow the AP select
802.11b and 802.11g connection automatically.
Mode It allows you to set the AP to AP, Client, WDS or AP +
WDS mode.
Network Type In client mode, you can specify your client to connect as an
infrastructure client or an ad hoc client.
SSID This is the name of the wireless LAN. All the devices in the
same wireless LAN should have the same ESSID.
Channel Number The channel used by the wireless LAN. All devices in the
same wireless LAN should use the same channel.
24
Enable MAC Clone Check the check box will let router copy the first seen
MAC address to the WLAN MAC.
Click on NEXT to proceed to the next page (step 5) Wireless Security.
Step 5) Wireless Security Settings
This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network.
Menu Description
None
Do not apply any encryption to wireless usage. Everyone can access the wireless without permission.
1.51 WEP
You can select the WEP key length for encryption, 64-bit or 128­bit. Larger WEP key length will provide higher level of security, but the throughput will be lower.
25
1.52 WPA(TKIP)
You can use a pre-shared key to authenticate wireless stations and encrypt data during communication. And use TKIP to change the encryption key frequently.
1.53 WPA2(AES)
You can use a pre-shared key to authenticate wireless stations and encrypt data during communication. And use CCMP(AES) to change the encryption key frequently.
1.54 WPA2 Mixed
This will use TKIP or AES based on the other communication peer automatically.
Select one of the Security types and set the manual’s relevant sub-section (1.51, 1.52, 1.53, or
1.54). Click on Back to return to the previous screen.
1.51 WEP
When you select 64-bit or128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as default key. Then the router can receive any packets encry pted by one of the four keys.
26
Parameters Description
Key Length You can select the WEP key length for encryption,
64-bit or 128-bit. Larger WEP key length will provide higher level of security, but the throughput will be lower.
Key Format You may select to select ASCII Characters
(alphanumeric forma t ) or Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key. For example: ASCII Characters: guest Hexadecimal Digits: 12345abcde
Default Tx Key Select one of the four keys to encrypt your data.
Only the key you select it in the "Default key" will take effect.
Encryption Key 1~4 The WEP keys are used to encrypt data transmitted
in the wireless network. Fill the text box by following the rules below. 64-bit WEP: input 10-digit Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A­F", "a-f" and "0-9" range) or 13-digit ASCII characters as the encryption keys.
Clicking on OK to save and active all the settings. Now, you can start to use the router as your internet gateway.
1.52 WPA(TKIP)
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a pre­shared key to authenticate wireless stations and encrypt data during communication. It uses TKIP to change the encryption key frequently. So the encryption key is not easy to be broken by hackers. This can improve security very much.
27
Parameters Description
Pre-shared Key Format You may select to select Passphrase (alphanumeric
format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Pre-shared Key. For example: Passphrase: iamguest Hexadecimal Digits: 12345abcde
Pre-shared Key
The Pre-shared key is used to authenticate and
encrypt data transmitted in the wireless network. Fill the text box by following the rules below. Hex: input 64-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys.
Clicking on OK to save and active all the settings. Now, you can start to use the router as your internet gateway.
28
1.53 WPA2(AES)
Wi-Fi Protected Access 2(WPA2) is an advanced security standard. You can use a pre­shared key to authenticate wireless stations and encrypt data during communication. It uses CCMP(AES) to change the encryption key frequently. So the encryption key is not easy to be broken by hackers. This can improve security very much.
Parameters Description
Pre-shared Key Format You may select to select Passphrase (alphanumeric format) or
Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Pre-shared Key. For example: Passphrase: iamguest Hexadecimal Digits: 12345abcde
Pre-shared Key The Pre-shared key is used to authenticate and encrypt data
transmitted in the wireless network. Fill the text box by following the rules below.
Hex: input 64-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys.
29
Clicking on OK to save and active all the settings. Now, you can start to use the router as your internet gateway.
1.54 WPA2 Mixed
Wi-Fi Protected Access 2(WPA2) is an advanced security standard. You can use a pre­shared key to authenticate wireless stations and encrypt data during communication. It uses TKIP or CCMP(AES) to change the encryption key frequently. So the encryption key is not easy to be broken by hackers. This can improve security very much.
Parameters Description
Pre-shared Key Format You may select to select Passphrase (alphanumeric format) or
Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Pre-shared Key. For example: Passphrase: iamguest Hexadecimal Digits: 12345abcde
30
Pre-shared Key The Pre-shared key is used to authenticate and encrypt data
transmitted in the wireless network. Fill the text box by following the rules below.
Hex: input 64-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys.
Clicking on OK to save and active all the settings. Now, you can start to use the router as your internet gateway.
31
Chapter 2
General Settings
Once you click on the General Setup button at the Home Page, you should see the screen below. If you have already configured the Quick Setup Wizard you do NOT need to configure anything
thing in the General Setup screen for you to start using the Internet. The General Setup contains advanced features that allow you to configure the router to meet
your network’s needs such as: Wireless, Address Mapping, Virtual Server, Access Control,
Hacker Attack Prevention, Special Applications, DMZ and other functions.
32
Below is a general description of what advance functions are available for this broadband router.
Menu Description
2.1 System
This section allows you to set the Broad band router’s system Time Zone, Password and Remote Management Administrator.
2.2 WAN
This section allows you to select the connection method in order to establish a connection with your ISP (same as the Quick Setup Wizard section)
2.3 LAN
You can specify the LAN segment’s IP address, subnet Mask, enable/disable DHCP and select an IP range for your LAN
2.4 Wireless You can setup the wireless LAN’s SSID, WEP key, MAC
filtering.
2.5 Firewall
The Firewall section allows you to configure Access Control, Hacker Prevention and DMZ.
Select one of the above five General Setup selections and proceed to the manual’s relevant sub­section
33
2.1 System
The system screen allows you to specify a time zone, to change the system password and to specify a remote management user for the broadband router.
Parameters Description
System Settings
2.1.1 Time Zone Setting
Select the time zone of the country you are currently in. The router will set its time based on your selection.
2.1.2 Password Setup
Allows you to select a password in order to access the web-based management website.
Select one of the above three system settings selections and proceed to the manual’s relevant sub-section
34
2.1.1 Time Zone Setting
The Time Zone Setting allows your router to reference or base its tim e on the set tings co nfigure d here, which will affect functions such as Log entries and Firew all settings.
Parameter Description
Current Time Set the current time. Time Zone Select Select the time zone of the country you are currently in.
The router will set its time based on your selection.
Enable NTP client update Check the box to enable router to update time from NTP
server.
NTP Server Select one preset time server or manual input a server
IP.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
2.1.2 Password Setup
You can change the password required to log into the broadband router's system web-based management. By default, there is no password. So please assign a password to the Administrator as soon as possible, and store it in a safe place. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive.
35
Parameters Description User Name Change your login user name.
New Password Enter your new password
Confirmed Password
Enter your new password again for verification purposes
Note: If you forget your password, you’ll have to reset the router to the factory default (No password) with the reset button (see router’s back panel)
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
36
2.2 WAN
Use the WAN Settings screen if you have already configured the Quick Setup Wizard section and you would like to change your Internet connection type. The WAN Settings screen allows to specify the type of WAN port connect you want to establish with your ISP. The WAN settings offer the following selections for the router’s WAN port, Static IP Address, DHCP Client, PPPoE, PPTP, and DDNS.
Parameters Description
2.2.1 Static IP Your ISP has given you an IP address already.
2.2.2 DHCP Client Your ISP will automatically give you an IP address.
2.2.3 PPPoE Your ISP requires PPPoE connection.
2.2.4 PPTP
Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection
.
Once you have made a selection, proceed to the manual’s relevant sub-section
37
2.2.1 Static IP
Select Static IP address if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information required in this section. (See chapter 1 “Static IP” for more detail)
2.2.2 DHCP Client
Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address (see chapter 1 “DHCP Client” for more detail)
2.2.3 PPPoE (PPP over Ethernet)
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required in this section. (See cha pter 1 “PPPoE” for more detail)
2.2.4 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. (See chapter 1 “PPTP” for more detail)
2.2.5 DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS, and TZO.
38
Parameters Default Description
Enable DDNS
Disable Enable/Disable the DDNS function of this router
Service Provider Select a DDNS service provider
Domain name Your static domain name that use DDNS User Name/Email The account that your DDNS service provider
assigned to you
Password/Key
The password you set for the DDNS service account above
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
2.3 LAN
The LAN Port screen below allows you to specify a private IP address for your router’s LAN ports as well as a subnet mask for your LAN segment.
Parameters Default Description
39
IP address
192.168.2.1 This is the router’s LAN port IP address (Your LAN clients default gateway IP address)
Subnet Mask
255.255.255.0 Specify a Subnet Mask for your LAN segment
Default Gateway Specify the default gateway for LAN
segment.
DHCP
Server You can select the DHCP type for LAN segment.
By selecting the DHCP server, the router will automatically give your LAN clients an IP address. By selecting the DHCP client, the router will get an IP address from LAN DHCP server automatically. If the DHCP server is not enabled then you’ll have to manually set your LAN client’s IP addresses; make sure the LAN Client is in the same subnet as this broadband router if you want the router to be your LAN client’s default gateway
DHCP Client Range
You can select a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients.
Note: By default the IP range is from: Start IP
192.168.2.100 to End IP 192.168.2.199. If you
want your PC to have a static/fixed IP address then you’ll have to choose an IP address outside this IP address Pool
802.1d Spanning Tree
Disabled If 802.1d Spanning Tree function is enabled, this
router will use the spanning tree protocol to prevent from network loop happened in the LAN ports.
Clone MAC Address
Specify the MAC Address for your LAN interface.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
40
2.4 Wireless
Wireless Access Point bui ld s a wireless LAN and can let a ll PCs equipped with IEEE
802.11b or 801.11g wireless network adaptor connect to your Intranet. It supports WEP, WPA and WPA2 encryption to enhance the security of your wireless network.
2.4.1 Basic Settings
You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, ESSID, Channel Number and Associated Client.
41
Parameters Default Description
Disable Wireless
Check this box to disable w ireless LAN.
LAN Interface
Band
It allows you to set the AP fix at 802.11b or
802.11g mode. You also can select B+G mode to allow the AP select 802.11b and 802.11g connection automatically.
Mode
It allows you to set the AP to AP, Client, WDS or
AP+WDS mode.
Network Type You can set the client mode to Infrastructure
or Ad Hoc mode here.
ESSID default
This is the name of the wireless LAN. All the
devices in the same wireless LAN should have the same ESSID.
Channel Number 11 The channel used by the wireless LAN. All
devices in the same wireless LAN should use the same channel.
42
Associated Clients
Click “Show Active Clients” button, then an “Active Wireless Client Table” will pop up. You can see the status of all active wireless stat ions that are connecting to the access point.
Enable MAC Clone Check the check box will copy the MAC address
of your PC to wireless Interface when the first packet was received.
Enable Universal
By enable the universal repeater mode, the.
Repeater Mode router will act as AP and client simultaneously. SSID of Extended Set the SSID for the extended wireless interface.
Interface
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
2.4.2 Advanced Settings
You can set advanced wireless LAN parameters of this router. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Preamble Type …… You should not change these parameters unless you know what effect the changes will have on this router.
43
Parameters Default Description
Authentication Type
There are two authentication types: "Open
System" and "Shared Key". When you select "Open System", wireless stations can associate with this wireless router without WEP encryption. When you select "Shared Key", you should also setup WEP key in the "Encryption" page and wireless stations should use WEP encryption in the authentication phase to associat e wit h this wireless router. If you select "Auto", the wireless client can associate with this wireless router by using any one of these two authentication types.
Fragment Threshold
"Fragment Threshold" specifies the maximum
size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.
RTS Threshold When the packet size is smaller the RTS
threshold, the wireless router will not use the RTS/CTS mechanism to send this packet.
Beacon Interval The interval of time that this wireless router
broadcast a beacon. Beacon is used to synchronize the wireless network.
Data Rate
The “Data Rate” is the rate this access point uses to transmit data packets. The access point will use the highest possible selected transmission rate to transmit the data packets.
Preamble Type
The “Long Preamble” can provide better wireless LAN compatibility while the “Short Preamble” can provide better wireless LAN performance.
Broadcast ESSID
If you enable “Broadcast ESSID”, every wireless station located within the coverage of this access point can discover this access point easily. If you are building a public wireless network, enabling this feature is recommended. Disabling “Broadcast ESSID” can provide better security.
IAPP
If you enable “IAPP”, it will allow wireless station roaming between IAPP enabled access points within the same wireless LAN.
802.11g Protection This is also called CTS Protection. It is
recommended to enable the protection
44
mechanism. This mechanism can decrease the rate of data collision between 802.11b and
802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to many of frame traffic should be transmitted.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router.
2.4.3 Security
This Access Point provides complete wireless LAN security functions, include WEP, IEEE 802.11x, IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stati ons use the same security function.
Parameters Default Description
Encryption You can choose no encryption, WEP, WPA,
WPA2 or WPA2 mixed mode for security.
45
Use 802.1x Authentication
IEEE 802.1x is an authentication protoc o l. E very user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. Check this box to authenticates user by IEEE 802.1x.
Key Length WEP 64-bit
You can select the WEP key length for
encryption, 64-bit or 128-bit. Larger WEP key length will provide higher level of security, but the throughput will be lower.
WPA Authentication WPA can authenticate by RADIUS or by Mode
pre-shared key.
WPA/WPA2 Cipher
You can choose TKIP or AES for WPA/WPA2 key exchange method.
Pre-shared Ke y Format
You may select to select Passphrase
(alphanumeric format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Pre­shared Key. For example:
Passphrase: iamguest Hexadecimal Digits: 12345abc de
Pre-shared Key The Pre-shared key is used to authenticate and
encrypt data transmitted in the wireless network. Fill the text box by following the rules below. Hex WEP: input 64-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys.
Radius Server Port
The service port of the external RADIUS server.
Radius Server IP The IP address of external RADIUS server.
Radius Server Password The password used by external RADIUS server.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
2.4.4 Access Control
This wireless router provides MAC Address Control, which prevents the unauthorized MAC Addresses from accessing yo ur wireless network.
46
Parameters Description
Wireless Access Control Mode E
nable/Disable wireless access control
Add MAC address into the list Fill in the "MAC Address" and "Comment" of the
wireless station to be added and then click "Add". Then this wireless station will be added into the "Current Access Control List" below.
Remove MAC address from the list If you want to remove some MAC address from
the "Current Access Control List ", select the MAC addresses you wa nt to remove in the list and then click "Delete Selected". If you want remove all MAC addresses from the table, just click "Delete All" button. Click "Reset" will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
2.4.5 Site Survey
This page provides tool to scan the wireless network. If an y Access Point or IBSS is found, you could choose to connect it manually when client mode is enabled.
47
2.4.6 WDS Settings
Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and t hen enable the WDS.
48
Parameters Description
Enable WDS
Check this box to enable Wireless Distribution System.
Add WDS AP into the list Fill in the "MAC Address" and "Comment" of the
wireless station to be added and then click "Apply Changes". Then this wireless AP will be added into the "Current WDS AP List" below. If you find any issues before adding it and want to retype again. Just click "Reset" and both "MAC Address" and "Comment" fields will be cleared.
Remove WDS AP from the list If you want to remove some AP from the
"Current WDS AP List ", select the MAC addresses you want to remove in the list and then click "Delete Selected". If you want remove all MAC addresses from the table, just click "Delete All" button. Click "Reset" will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
49
2.5 Firewall
The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attack, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).
Parameters Description
2.5.1 Port Filtering
Entries in this table are used to restrict certain types of data packets from your local network to Internet throug h th e Gat eway.
2.5.2 IP Filtering
IP Filtering allows you to specify which IP can or can not be used to access to internet.
2.5.3 MAC Filtering
MAC Filtering allows you to specify which MAC Address can or can not be used to access to internet.
2.5.4 Port Forwarding
You can have different services (e.g. email, FTP, Web etc.) going to different service servers/clients in your LAN. The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a particular LAN IP address.
2.5.5 DMZ
The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN.
50
Click on one of the firewall selections and proceed to the manual’s relevant sub-section
2.5.1 Port Filtering
If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), then this is the place to set that configuration. Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network.
Parameters Description
Enable Port Filtering
Check this box to enable the port filtering function.
Add a new entry into the list
Fill in the "Port Range", "Protocol" and "Comment" of the filtering rule to be added and then click "Apply ". Then specified port will be added into the "Current Filter Table" below. If you find any issues before adding it and want to retype again. Just click "Cancel" and all inputed fields will be cleared.
Remove an entry from the list If you want to remove some filter rule from the "Current
Filter Table", select the Port Range you want to remove in the table and then click "Delete Selected". If you want remove all Port Ranges from the table, just click "Delete All" button. Click "Reset" will clear your current selections.
51
You can now configure other advance sections or start using the router (with the advance settings in place)
2.5.2 IP Filtering
If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), then this is the place to set that configuration. Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network.
Parameters Description
Enable IP Filtering
Check this box to enable the IP filtering function.
Add a new entry into the list
Fill in the "Local IP Address", "Protocol" and "Comment" of the filtering rule to be added and then click "Apply ". Then specified IP will be added into the "Current Filter Table" below. If you find any issues before adding it and want to retype again. Just click "Cancel" and all inputed fields will be cleared.
Remove an entry from the list If you want to remove some filter rule from the "Current
Filter Table", select the Local IP Address you want to remove in the table and then click "Delete Selected". If you want remove all Local IP Address from the table,
52
just click "Delete All" button. Click "Reset" will clear your current selections.
You can now configure other advance sections or start using the router (with the advance settings in place)
2.5.3 MAC Filtering
If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), then this is the place to set that configuration. Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network.
Parameters Description
Enable MAC Filtering
Check this box to enable the MAC filtering function.
Add a new entry into the list
Fill in the "MAC Address" and "Comment" of the filtering rule to be added and then click "Apply ". Then specified MAC will be added into the "Current Filter Table" below . If you find any issues before adding it and want to retype again. Just click "Cancel" and all inputed fields will be cleared.
Remove an entry from the list If you want to remove some filter rule from the "Current
Filter Table", select the MAC Address you want to remove in the table and then click "Delete Selected". If
53
you want remove all MAC Address from the table, just click "Delete All" button. Click "Reset" will clear your current selections.
You can now configure other advance sections or start using the router (with the advance settings in place)
2.5.4 Port Forwarding
The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a particular LAN IP address. It helps you to host some servers behind the router NAT firewall.
Parameter Description
Enable Port Forwarding
Enable Port Forwarding
IP Address This is the private IP of the server behind the
NAT firewall.
Note: You need to give your LAN PC clients a
fixed/static IP address for Port Forw arding to work properly.
Protocol This is the protocol type to be forwarded. You
can choose to forward “TCP” or “UDP” packets only or select “both” to forward both “TCP” and “UDP” packets.
54
Port Range The range of ports to be forward to the private IP. Comment The description of this setting. Add Port Forwarding into the table Fill in the "IP Address", “Protocol”, “Port Range”
and "Comment" of the setting to be added and then click "Apply". Then this Port Forwarding setting will be added into the "Current Port Forwarding Table" below. If you find any typo before adding it and want to retype again, just click "Cancel" and the fields will be cleared.
Remove Port Forwarding into the table If you want to remove some Port Forwarding
settings from the "Current Port Forwarding Table", select the Port Forwarding settings y ou want to remove in the table and then click "Delete Selected". If you want remove all Port Forwarding settings from the table, just click "Delete All" button. Click "Reset" will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
2.5.5 DMZ
If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open the client up to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. The difference between the virtual server and the DMZ function is that the virtual server re-directs a particular service/Internet application (e.g. FTP, websites) to a particular LAN clie nt/ s erv er, w h ereas DM Z re-d irec t s all pack ets (regardless of services) going to your WAN IP address to a particular LAN client/server.
55
Parameters Description Enable DMZ Enable/disable DMZ
DMZ Host IP Address Input the IP address of a particular host in your LAN that will
receive all the packets originally going to the WAN port/Public IP address above
Note: You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly.
You can now configure other advance sections or start using the router (with the advance settings in place
56
Chapter 3
Status
The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the connection status of the Broadband router's WAN/LAN interfaces, the current firmware version numbers, and any illegal attempts to access your network.
Parameters Description
3.1 Status
Shows the router’s system information
3.2 System Log View the Broadband router’s system log
3.3 Statistics Shows the statistics
Select one of the above five Status selections and proceed to the manual’s relevant sub-section
57
3.1 Status
The Status section allows you to view the router’s system information
Parameters Description
Information
You can see the router’s system information such as the router’s: Uptime, Firmware version, Wireless Configuration, LAN Address information, WAN Configuration information.
3.2 System Log
View the operation log of the system.
58
Parameters Description
Enable Log
Check this box to enable the logging system.
Log mode
By select this options, you can have wireless log only or all system log.
Enable Remote Log
If you want to send all log information to remote server, please check this box to enable this function and fill the server IP Address in the “Log Server IP Address” field.
System Log
This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be cleared <Clear> or it can be refreshed <Refresh> to get the most updated situation. When the system is powered down, the system log will disappear if not saved to a local file.
59
3.3 Statistics
View the statistics of packets sent and received on WAN, LAN and Wireless LAN.
Parameters Description
Statistics Shows the counters of
packets sent and received on WAN,
LAN and Wireless LAN.
60
Chapter 4
Tool
This page includes the basic configuration tools, such as Configuration Tools (save or restore configuration settings), Firmware Upgrade (upgrade system firmware) and Reset.
Parameters Description
4.1 Save/Reload Settings
You can save the router’s current configuration, restore the router’s saved configuration files and restore the router’s factory default settings
4.2 Upgrade Firmware
This page allows you to upgrade the router’s firmware
Select one of the above three Tools Settings selection and proceed to the manual’s relevant sub-section
61
4.1 Save/Reload Settings
The Save/Reload Settings screen allows you to save (Backup) the router’s current configuration setting. Saving the configuration settings provides an added protection and convenience should problems occur with the router and you have to reset to factory default. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection. If extreme problems occur you can use the Restore Settings to Defaults selection, this will set all configurations to its original default settings (e.g. when you first purchased the router).
Parameters Description
Configuration Tools
Use the "Backup" tool to save the Broadband router current configuration to a file named "config.bin" on your PC. You can then use the "Restore" tool to restore the saved configuration to the Broadband router. Alternatively, you can use the "Restore Settings to Default" tool to force the Broadband router to perform a power reset and restore the original factory settings.
62
4.2 Firmware Upgrade
This page allows you to upgrade the router’s firmware
Parameters Description
Upgrade Firmware
This tool allows you to upgrade the Broadband router’s system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.
Once you’ve selected the new firmware file, click <Apply> at the bottom of the screen to start the upgrade process. (You may have to wait a few minutes for the upgrade to complete). Once the upgrade is complete you can start using the router.
63
Appendix A
How to Manually find your PC’s IP and MAC address
1) In Window’s open the Command Prompt program
2) Type Ipconfig /all and <enter>
Your PC’s IP address is the one entitled IP address (192.168.1.77)
The router’s IP address is the one entitled Default Gateway (192.168.1.254)
Your PC’s MAC Address is the one entitled Physical Address (00-50-FC-FE-02-DB)
64
Glossary
Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP
address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination.
DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every computer on your home network an IP address.
DNS Server IP Address: DNS stands for Domain Name System, which allows Internet servers to have a domain name (such as www.Broadbandrouter.com) and one or more IP addresses (such as 192.34.45.8). A DNS server keeps a database of Internet servers and their respective domain names and IP addresses, so that when a domain name is requested (as in typing "Broadbandrouter.com" into your Internet browser), the user is sent to the proper IP address. The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you.
DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your existing phone lines to transmit data at high speeds.
Ethernet: A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10/100 million bits per second (Mbps).
Idle Timeout: Idle Timeout is designed so that after there is no traffic to the Internet for a pre­configured amount of time, the connection will automatically be disconnected.
IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address consists of a series of four numbers separated by periods, that identifies a single, unique Internet computer host in an IP network. Example: 192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier.
The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each “aaa” can be anything from 000 to 255, or as four cascaded binary numbers separated by “.”: bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b” can either be 0 or 1. A network mask is also a 32-bit binary pattern, and consists of consecutive leading 1’s followed by consecutive trailing 0’s, such as
11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x” number of leading 1’s. When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1’s in the network mask become part of the IP network address, and the remaining bits correspond to the host ID.
For example, if the IP address for a device is, in its binary form,
11011001.10110000.1001
0000.00000111, and if its network mask is,
11111111.11111111.11110000.00000000 It means the device’s network address is
11011001.10110000.1001
0000.00000000, and its host ID is,
00000000.00000000.00000000.00000111
. This is a convenient and efficient method for routers
to route IP packets to their destination.
ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet router located at the ISP's office.
65
ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations.
LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). Your hom e net work is considered a LAN.
MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are often used as the product’s serial number.
NAT: Network Address Translation. This process allows all of the computer s on your home network to use one IP address. Using the broadband router’s NAT capability, you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP.
Port: Network Clients (LAN PC) uses port numbers to distinguish one network application/protocol over another. Below is a list of common applications and protocol/port numbers:
Application Protocol Port Number Telnet TCP 23 FTP TCP 21 SMTP TCP 25 POP3 TCP 110 H.323 TCP 1720 SNMP UCP 161 SNMP Trap UDP 162 HTTP TCP 80 PPTP TCP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632
PPPoE: Point-to-Point Protocol over Ethernet. Point-to-Point Protocol is a secure data transmission method originally created for dial-up connections; PPPoE is for Ethernet connections. PPPoE relies on two widely accepted standards, Ethernet and the Point-to-Point Protocol. It is a communications protocol for transmitting information over Ethernet between different manufacturers
Protocol: A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol, the interpretation of their behavior is well defined and can be made objectively, without confusion or misunderstanding.
Router: A router is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses.
Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to
66
create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC).
TCP/IP, UDP: Transmission Control Protocol/Interne t Prot oc ol (T C P / I P) an d Unre liabl e Dat agram Protocol (UDP). TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocol. TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They both run on top of the IP (Internet Protocol), a network layer protocol.
WAN: Wide Area Network. A network that connects computers located in geographically separate areas (e.g. different buildings, cities, countries). The Internet is a wide area network.
Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor the device being managed.
Note: In the event of incorrect installation and improper use in a residential area, the device may cause disruptions in radio devices and other electronic devices. Proper use means that the device is operated with shielded connector cables as far as possible, for network products also with shielded cables of category 5e and higher. The device was tested and lies within the limits for computer accessories of class A according to the requirements of EN 55022.
Warning ! This is a class A device. This device can cause radio interference in residential areas; in this case, the operator may be required to perform and bear the costs for appropriate measures.
Conformity Declaration: The device fulfils the EMC requirements of EN 55022 class A for ITE and EN 55024. Devices with external or built-in power supply also fulfil the requirements of EN 61000-3-2 and EN 61000-3-3. The basic protection requirements of the “EMC Directive” 89/336/EEC are therefore fulfilled. The CE conformity has been certified. The corresponding declarations are available from the manufacturer.
Trademarks: All company, brand and product names used in these instructions are trademarks or registered marks of the corresponding companies.
Loading...