HDMI KVM Extender over IP
Manual
DS-55202
Important Safety Instruction
1. Do not mix up the transmitter and receiver before instruction.
2. Do not unplug the device, when it is in using; keep distance from
inflammable and explosive devices.
3. Power Supply: DC 5V, Use only the supplied power supply unit, do not use
the power supply if it is damaged.
Product Introduction
This is a HDMI KVM EXTENDER, is made up of a transmitter unit (local site) and a
receiver unit (remote site). The HDMI signal can be extended up to 120 meters via
network cable, and the resolution supported is up to 1080p@60Hz. It allows access
to a computer system from a remote console by USB connectors (USB keyboard and
mouse). It is perfect for factory and construction sites, or any type of installation
where the console needs to be in a conveniently accessible location. It is also useful
for control and security purposes. Therefore it is wildly used in command center, data
control center, operation rooms in military, bank, government, enterprise etc.
Features
1. Extend HDMI signal up to 120 meters via a single network cable
2. Over IP connection through network switch
3. High resolution supported is up to 1080p@60Hz
4. LED indicators, know the status of power and USB connection easily
5. Support KVM function, remote control conveniently
6. Support LAN standard 802.3 Ethernet 10/100/1000Mbps
7. Compliant STP and UTP CAT5/5E/6 network cables
8. Aluminum alloy housing design, stable and durable
Package Content
HDMI KVM EXTENDER TX x1pcs
HDMI KVM EXTENDER RX x1pcs
USB Cable x1
Power supply x2pcs
User manual ×1pcs
CD (Windows USB driver) x1pcs
Installation Requirements
1. Source devices: PC or other devices with HDMI graphics card.
2. Display devices: With HDMI input port, SDTV, HDTV, and monitor.
3. Network cables:
UTP/STP CAT5E/6 network cables, which following the standard of IEEE-568B.
4. Transmission length:
CAT5: 80m/CAT5E: 100m/CAT6: 120m.
Panel Introduction
1. HDMI EXTENDER TX (Transmitter)
① Power indicator
② USB connection indicator
③ LAN signal output
④ Reset button
⑤ Power input (DC5V)
⑥ HDMI signal input
⑦ USB port: to connect with PC
2. HDMI EXTENDER RX (Receiver)
① Power indicator
② USB connection indicator
③ LAN signal input
④ Reset button
⑤ Power input (DC5V)
⑥ HDMI signal output
⑦ USB port: to connect with keyboard/mouse
Installation Procedures
1. How to make a CAT5E/6 network cable
Follow the standard of IEEE-568B:
1- Orange/white
2- Orange
3- Green/white
4- Blue
5- Blue/white
6- Green
7- Brown/white
8- Brown
2. General Connection Diagram
Transmission distance can be up to 120 meters for 1080p over one CAT6
HDMI
Transmitter TX
Receiver RX
HDMI
PC
USB
cable
TV
USB
keyboard/mouse
NOTE: Point to multi-point connection via switch is supported too, but under point to
multi-point configuration, it is strongly recommended to operate KVM function on
one receiver only at the same time.
3. Over IP Connection Diagram
Transmitter TX
cable
Switch Switch*N
PC
HDMI
USB
Receiver RX
TV
keyboard/mouse
NOTE: Transmission distance depends on type of network cable, CAT5: 80m,
CAT5E: 100m, CAT6: 120m.
Remark: Install driver Software
Driver only needed if the USB keyboard mouse cannot be activated automatically in
the first time connection. (Only Windows USB driver available)
FAQ
Q: Yellow light of LAN port is flashing but slowly?
A: 1) Check whether HDMI Extender Transmitter and HDMI Extender Receiver is
reversed;
2) Check whether HDMI source device output HDMI signal correctly;
3) Change the HDMI cable of Transmitter.
Q: Yellow light of LAN port is flashing quickly but no display?
A: 1) If HDMI source is graphics card please set the resolution to be supported by
display
2) Check whether HDMI cable of Receiver is well connected;
3) Change the HDMI cable of Receiver.
Q: Yellow Led light of LAN port is not light?
A: 1) Check connection of network cable;
2) Network cable is too long.
Q: Abnormal color display or flashing after all the devices is well connected?
A: 1) Please press reset button of HDMI extender.
2) Make sure the network cable is made according to the standard of
IEEE-568B.
Q: USB does not work?
A: Install the USB driving software, check and make sure the USB cables are
connected well, then reset Transmitter or Receiver.
Specification
Part No. DS-55202
Technical Transmitter-TX Receiver-RX
Signal format HDMI 1.3
HDCP HDCP 1.2
HDMI connector Type A, 19 pin, Female
Transmission distance CAT5/80 meters, CAT5e/100meters, CAT6/120 meters
LAN connector RJ-45
Video bandwidth ≤ 70Mbps
resistance 75Ω
Video Latency 70 ms
640*480@60Hz 800*600@60Hz
HDMI resolution
supported
Audio support PCM (44.1KHz, 48KHz)
KVM function (connect
with PC, keyboard/
mouse)
1024*768@60Hz 1280*720@60Hz
1360*768@60Hz 1440*900@60Hz
1400*1050@60Hz 1680*1050@60Hz
1920*1080@60Hz
connect with PC connect with keyboard/mouse
Switch Connection yes
Input
1×HDMI
1XUSB
(to connect with PC)
2xUSB (to connect with
keyboard/mouse)
1×RJ45
Output 1×RJ45 1×HDMI
Mechanical Transmitter-TX Receiver-RX
Housing Metal enclosure
Dimension 109.6 (L) x 89.5 (w) x 26.3 (H) mm
Net weight 160g 170g
Power supply DC5V 1A
Power consumption < 3.5W < 3.5W
Operation temperature 0-60°C
Storage temperature -20-70°C
Relative humidity 20-90% (no condensation)
Hereby ASSMANN Electronic GmbH, declares that this device is in compliance with the requirements of
Directive 2014/30/EU (EMC), Directive 2014/35/EU (LVD) and the Directive 2011/65/EU for RoHS
compliance. The complete declaration of conformity can be requested by post under the below mentioned
manufacturer address.
Note:
If wrongly installed or improperly used in the living area, the device can cause interference in radios and
other electronic devices. Appropriate use is when the device, as far as feasible, is operated with shielded
connection cables (with network products in addition to category 5 shielded cables and higher). The device
has been tested and falls within the limits of class A computing equipment according to the requirements of
EN 55032.
Warning:
This device conforms with test category A - it can cause radio interference in the living area; in this case the
operator may demand that appropriate measures are implemented and arise for this reason. Declaration of
conformity: The device fulfills the EMV requirements according to EN 55032 for ITE and EN 55024 class A. In
this way, the fundamental protection requirements of the EMV-2014/30/EU guideline are fulfilled.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Loading...