Digitus DS-53200 User Manual

VGA over IP EXTENDER

Manual

DS-53200

2

1. Introduction

Thanks for purchasing the DS-53200 VGA over IP Extender. We recommend that you read

this manual thoroughly and retain for future reference.

1.1 Features

The VGA over IP Extender allows you to extend video and audio up to 100 meters distance

between source or computer and monitor or projector. With the built-in video and audio

signals enhancement, you can gain the best video resolution quality and audio stereo sound

while listening, and no any additional software needed. Furthermore, the installation and

operation are easily more than expected. With using extension facilities of video and audio,

this product the VGA over IP Extender, delivers worthy of performing efficiency and

value-added.

 Cascadable Receiver, each Receiver Unit with cascade function enables to link the

other two Receiver Units consecutively extending another 100m distance, and continue

expanding corresponding to custom demand as likely Cascade/Tree Chain web

architecture spread

 Easy to install with inexpensive CAT.5e/6 cables

 Each pair (TX & RX) extends the signals up to 100m (330 feet)

 Supports video high resolution up to 1920x1080@60Hz, Full HD 1080p

 HDTV compatible (720p, 1080i, 1080p)

 Supports Stereo 2.0

 Cascaded-chainable receiver up to 10 layers

 Supports RS-232 (Serial)

 IR (Infrared remote) enabled

 Support Local VGA monitoring port

 Each receiver (remote) distributed linking cascade-chainable 2 receivers

 Wall Mountable

1.2 Package Contents

1. VGA Extender Transmitter (TX) x 1

2. VGA Extender Receiver (RX) x 1

3. Audio cable x 1

4. RS232 adapter cable x 2 pcs (set units) or 1 ( single unit)

5. IR ( Emitter + Receiver ) cables x 1 set

6. Power Adaptor DC 5V x 2 pcs ( set units ) or 1 ( single unit )

7. User’s Manual x 1

3

2. Specifications:

2.1 General

Transmitter Receiver

Console
Connectors

VGA Output

VGA (Female) VGA (Female)

RS-232 Control
Port

Phone Jack Phone Jack

PC
Connectors

VGA Input

VGA (Male) N/A

Extension
Port

RJ-45

Full HD Video / Audio Extension

RJ-45

1 (Line Out) 3 (1 Line In & 2 Line Out)

Cascaded-Chainable

N/A Up to 10 layers

Audio

Supports Stereo 2.0

IR

Unidirectional (Receiver RX to Transmitter TX)

LED
Indicators

Local

Power

Red LED

Link

Red Green

Remote

Power

Red LED

Link

Red Green

DDC Supported

DDC/ DDC2 /DDC2B

Extension Cable Type &
Length

CAT.5e / CAT.6 Max. Length: 100m

Max. Video Resolution

HDMI: 1920 x 1080@60Hz, Full HD 1080p

Wide Screen Supported

yes

Power Supply

External DC 5V / 2A Power Adapter

Dimension ( L x W x H )

115 x 91 x 28 mm

Weight

340g 380g

Housing material

Metal

Power Consumption

Transmitter (TX) : 5W ; Receiver (RX): 4.5W

Operating Temperature

32 – 122 F ( 0 – 50 C )

Working Temperature

-20

℃ ~ 60 ℃

Humidity

0% - 80% RH

4

3. Connectors Diagram

3.1 Configuration Pictures

:

Power adapter DC 5V

:

Audio-out port

:

Power LED (Solid Red when power present)

:

Local VGA monitoring

:

Link LED (Solid Green when link present)

:

VGA source

:

IR Emitter control port

:

Audio-in port

:

RS232 control port

:

RJ45 CAT.5e/6 UTP port

:

Power adaptor DC5V

:

Audio-out port

:

Power LED (Solid Red when power present)

:

VGA output ( remote display)

:

LINK LED (Solid Green when link present)

:

RJ45 LINK

:

IR receiver control port

:

RJ45 LINK

:

RS232 control port

:

RJ45 LINK

Transmitter (TX) – Front View Transmitter (TX) – Rear View

Receiver (RX) – Front View Receiver (RX) – Rear View

5

Application Diagram

Transmitter (TX) Installation

 Please use CAT.5e/6 cable to get the best quality to connect to

the LINE port (RJ45) of Transmitter

 Connect the IR Blaster Emitter cable or RS-232 to 3.5mm adapter to the Transmitter Unit IR

Port or RS-232 port if necessary

 Connect Transmitter with VGA cable to a VGA source

 Connect Transmitter with VGA cable to a VGA monitor

 Connect DC 5V power adapter

Connect to UTP cable

Connect to local VGA monitor

Connect to local speaker

Connect to VGA source

Power Adapter 5V

Connect to audio source

6

Receiver (RX) Installation

 Please use CAT.5e/6 cable to get the best quality to connect to the LINE1 or LINE2 or

LINE3 port (RJ45) of Receiver

 Connect the IR Receiver cable or RS-232 to 3.5mm adapter to the Receiver Unit IR Port or

RS-232 port if necessary

 Connect Receiver with VGA cable to a VGA monitor

 Connect DC 5V/2A power adapter.

Cascade Chain Connection

 Use UTP Cable to connect with Receiver to link the other two Receiver Units consecutively

for extending another 100m distance, the cable is to connect to Receiver LINE1 or LINE2

or LINE3 port (RJ45), as long as the LINE port is not occupied, and user can continue

expanding corresponding to custom demand as likely Cascade/Tree Chain web

architecture spread

 Connect the IR Receiver cable or RS-232 to 3.5mm adapter to the Receiver Unit IR Port or

RS-232 port if necessary

 Connect Receiver with HDMI cable to HDMI connector of Display Monitor

 Connect DC 5V power adapter

4

Connect to VGA monitor

Connect to speaker

Power Adapter 5V

Connect to UTP cable

Connect to VGA monitor

Connect to UTP cable

Connect to speaker

Power Adapter 5V

7

Each Receiver with three Line port, one is used for source input; others are used for expanding

source to other receivers. User can choose any LINE port as source input random and use the

other two LINE port for expanding source to next tier receiver as long as the LINE port is not

occupied.

Network Switch Extending

 The maximum distance between each tier could be up to 100 meters long, while this could

be extended through Network Switch. User can add one Network Switch to extend another

100 meter

 The more Network Switches, the longer distance extended. The number of Network

Switches can be as many as user want

8

3.2 Connection Diagram

(1) Single Source Extension

(2) Single Source Extension and Receivers Cascade Chaining

(3) Single Source with Multiple Receivers Cascaded

VGA Cable

9

Cascaded and mixed with VGA / HDMI / DisplayPort

IR Bypass function connection

 Connect the IR Transmitter (or Emitter) cable to the IR Connector on the Transmitter (TX)

 Connect the IR Receiver cable to the IR Connector on the Receiver (RX)

 Place the IR Eye of the IR Receiver cable near the Remote Controller

 Place the IR Blaster of the IR Transmitter cable near the device that intend to be controlled

by the Remoter controller

V

GA Out

VGA

VGA

10

3.3 RS-232 Bypass function connection

 Connect the device, such as a PC, projector…etc, to the RS-232 port of the Transmitter or

Receiver via a RS-232 to 3.5mm adatper



Connect the controlling device to the RS-232 port of the Receiver or Receiver via a RS-232

to 3.5mm adapter