Page 1
HD NETWORK
SURVEILLANCE CAMERA
INSTALLATION GUIDE
Please read instructions thoroughly before operation and retain it for future reference.
Page 2
2
IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the European law on
the Restriction of Hazardous Substances (RoHS) directive, which means our manufacture processes
and products are strictly “lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be
collected separately at the product end-of-life. This applies to your product and any peripherals
marked with this symbol. Do not dispose of these products as unsorted municipal waste. Contact your
local dealer for procedures for recycling this equipment.
Trademark Acknowledgements
iPhone® is the registered trademark of Apple Inc.
BlackBerry® and related trademarks, names and logos are the property of Research In Motion Limited and are
registered and/or used in the U.S. and countries around the world. Used under license from Research In Motion
Limited.
Android™ is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.
Windows Mobile & Symbian mentioned in this document are the registered trademarks of their respective holders.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume any
legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of this manual
is subject to change without notice.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH
THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG4 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS
GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED
FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies
and which are subject to the GNU General Public License (“GPL”) or the
GNU Lesser Public License (“LGPL”).
The GPL Code used in this product is released without warranty and is subject
to the copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. The codes are provided on
the FTP site, and please download them from the following site or you can refer to your
distributor.
Page 3
3
TABLE OF CONTENTS
1. OVERVIEW ................................................................................................................... 4
1.1 Package content ..................................................................................................................................... 4
1.2 Rear Panel ............................................................................................................................................. 4
1.3 Status Indicator ....................................................................................................................................... 5
2. INSTALLATION & CONNECTION ................................................................................. 6
2.1 Install the camera ................................................................................................................................... 6
2.2 Connect to power ................................................................................................................................... 6
3. CAMERA ACCESS AND NETWORK CONFIGURATION .............................................. 6
3.1 Network connection via LAN .................................................................................................................. 6
3.2 Camera access via web browser ......................................................................................................... 10
3.3 Video adjustment .................................................................................................................................. 11
3.4 Network configurations ......................................................................................................................... 12
3.4.1 Network environment setting .................................................................................................... 12
3.4.2 Internet access setting .............................................................................................................. 12
3.4.3 DDNS setting ............................................................................................................................ 13
APPENDIX 1 CREATING AN ACCOUNT FOR DDNS SERVICE .......................................... 14
APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES ................................................. 16
A2.1 Prerequisites ...................................................................................................................................... 16
A2.2 Where to download ............................................................................................................................ 16
Page 4
4
1. OVERVIEW
1.1 Package content
□ Network camera □ Camera Bracket
□ Installation Guide □ Adapter
□ CD-ROM disc (including user manuals & CMS software “Video Viewer”)
1.2 Rear Panel
1 Ethernet: Connect your network cable.
2 DC 5V: Connect the supplied regulated power supply.
3 Reset:
With the power connected, press and hold for a few
seconds to reset all parameters, including the IP
address to factory default settings.
The camera will reboot after default reset. You may
check the blinking frequency of the LED indicator to
know if the camera is in the reset default mode.
Please do not disconnect your camera during the reset
process.
Page 5
5
1.3 Status Indicator
1
Status Indicator
2
Camera Lens
3
White LED
ICON
LAN connection status Internet connection status
System Status
During powering on
A
lways on
A
lways on
Reset default
Blinking
(on 250 ms, off 250 ms) Always off
Upgrade
Blinking
(on 250 ms, off 250 ms) Blinking (on 250 ms, off 250 ms)
Connection Status
LAN connected
A
lways on --
LAN disconnected
Blinking
(on 100 ms, off 500 ms) --
Internet connected --
A
lways on
Internet disconnected
--
Blinking (on 100 ms, off 500 ms)
* LED blinking frequency - LED on / LED off
Page 6
6
2. INSTALLATION & CONNECTION
2.1 Install the camera
1. Find the bracket and its accessories supplied with the camera.
2. Attached the base of the bracket (the round one) to where you want to install this camera,
and fasten it with the supplied screws.
3. Assemble the bracket as illustrated below, and adjust the angle of the camera.
2.2 Connect to power
Connect the supplied power adapter to the camera’s power jack (DC 5V) on the
rear panel and the power outlet.
3. CAMERA ACCESS AND NETWORK CONFIGURATION
Before using this network camera, please follow the instructions below to finish the network
connection settings based on your installation environment:
To configure the network settings, you must connect the camera to your PC by LAN. For
details, please refer to “3.1 Network connection via LAN” at page 6.
To configure the network settings via a web browser, please refer to “Fehler! Verweisquelle
konnte nicht gefunden werden.” at page Fehler! Textmarke nicht definiert..
3.1 Network connection via LAN
Step1: Connect this network camera and your PC via a RJ45 network cable, and make sure the
camera is powered on.
Step2: Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10).
Page 7
7
For Windows XP users:
a) Select “start” “Control Panel” “Network and Internet Connections” “Network Connections” (If
you’re in “Category View”).
In “LAN or High-Speed Internet”, right-click on “Local Area Connection”, and select “Properties”.
Note: If your local area connection is not enabled, please also enable it.
b) In the “General” tab, select “Internet Protocol (TCP/IP)”, and select “Properties”.
c) In the “General” tab, select “Use the following IP address”, and set the IP address to “192.168.1.XXX”
(XXX can be any value from 1~255 except 10).
Note: It’s recommended to note down the current settings first and then change as
instructed. It’s helpful when you need to restore the PC network settings for
connecting to Internet later.
d) Click “OK” to close the “Internet Protocol (TCP/IP) Properties” dialog box. Then, click “Close” to close
the “Local Area Connection Properties” dialog box.
Page 8
8
For Windows Vista users:
a) Select “ ” (start) “Control Panel” “Network and Internet” to enter the “Network and
Sharing Center”. Then, click “Manage network connections” (If you’re in “Category View”).
b) Right-click on “Local Area Connection”, and select “Properties”.
Note: If your local area connection is not enabled, please also enable it.
c) In the “Networking” tab, select “Internet Protocol Version 4 (TCP/IPv4)”, and select “Properties”.
d) n the “General” tab, select “Use the following IP address”, and set the IP address as described below.
Note: It’s recommended to note down the current settings first and then change as
instructed. It’s helpful when you need to restore the PC network settings for
connecting to Internet later.
Page 9
9
e) Click “OK” to close the “Internet Protocol Version 4 (TCP/IPv4) Properties” dialog box. Then, click
“Close” to close the “Local Area Connection Properties” dialog box.
For Windows 7 users:
a) Select “ ” (start) “Control Panel” “Network and Internet” to enter the “Network and Sharing
Center”. Then, click “Change adapter settings”.
b) Right-click on “Local Area Connection”, and select “Properties”.
Note: If your local area connection is not enabled, please also enable it.
c) In the “Networking” tab, select “Internet Protocol Version 4 (TCP/IPv4)”, and select “Properties”.
d) In the “General” tab, select “Use the following IP address”, and set the IP address as described
below.
Note: It’s recommended to note down the current settings first and then change as
instructed. It’s helpful when you need to restore the PC network settings for
connecting to Internet later.
Page 10
10
e) Click “OK” to close the “Internet Protocol Version 4 (TCP/IPv4) Properties” dialog box. Then, click
“Close” to close the “Local Area Connection Properties” dialog box.
3.2 Camera access via web browser
Step1: Open your web browser, for example, Microsoft Internet Explorer, and enter
“http://192.168.1.10” in the URL address box.
Page 11
11
Step2: In the login page, key in the default user name (admin) and password (admin), and
enter the security code from the image below. Then, click “LOGIN” to log into the
camera and check the live view.
Note: Skip the wizard if any.
3.3 Video adjustment
When you’ve accessed the camera successfully, it’s recommended to adjust the video images if
needed.
To adjust the clearness of the video, rotate the camera lens manually as shown in Figure 1.
To slightly adjust the color of the video, in the live page of your web browser, click “Config” on the top
right side of the browser to open the configuration page.
Then, click “Camera” “Color” to adjust the brightness / contrast / hue / saturation of the
video images, as shown in Figure 2.
Rotate
Figure 1 Figure 2
Page 12
12
3.4 Network configurations
3.4.1 Network environment setting
Step1: Click “Config” in the live view page of your browser to enter the configuration page.
Then, click “Camera” “Camera”.
Step2: In this page, define your installation environment as indoor or outdoor, and set other
parameters related to your network environment.
Item Description
Environment Select the current environment for the camera to automatically adjust itself to produce the
images suitable for the selected environment.
Frame Rate The frame rate allowed to each viewer can be adjusted to adapt to the bandwidth on the
network.
Set the desired image frequency to the maximum (FULL) or to a specified frame rate (1/2;
1/3; 1/4; 1/5; 1/10; 1/15).
The actual frame rate depends on the actual network connection, and may be lower than the
specified one.
Stream Format Select the stream format to H.264 / MPEG-4 / Motion JPEG / Multi-Mode suitable for your
network bandwidth.
Note:
1. Motion detection is not supported when the stream format is set to Motion JPEG.
2. Face detection is not supported when the stream format is set to Multi-Mode.
ADSL Upload Speed Select your Internet upload speed, and the system will automatically adjust your data flow.
The options are: Local (>2Mbps) / 2M (2000Kbps) / 1M (1000Kbps) / 640Kbps / 512 Kbps /
256Kbps / 128 Kbps / 64Kbps
3.4.2 Internet access setting
Step1: Click “Network” “Network” to select the connection type: Static IP / PPPoE / DHCP.
Note: This camera doesn’t support POE router or hub.
Page 13
13
For Static IP:
a) Enter the information of “Server IP”, “Gateway” and “Net Mask” obtained from your ISP (Internet
Service Provider).
b) Enter the port number. The valid number ranges from 1 to 9999. The default value is 80. Typically,
the TCP port used by HTTP is 80. However in some cases, it is better to change this port number for
added flexibility or security.
c) Click “Save” to save your network configurations, and log out.
d) Disconnect your camera and your PC, and connect them to Internet separately. Then, enter the IP
address or host name you just note down in the URL address box of the web browser, and see if you
can access the camera successfully.
For PPPOE:
a) Enter the user name and password obtained from your ISP, and click “Save”.
b) Continue the DDNS setting as instructed in “3.4.3 DDNS Setting”.
For DHCP:
a) Before selecting this option, you need to finish the DHCP router settings first.
Get a router and connect it to the Internet via your PC (with Static IP or PPPoE setting). There are
different setting methods for different routers. Please refer to their respective user manuals.
b) Continue the DDNS setting as instructed in “3.4.3 DDNS Setting”.
3.4.3 DDNS setting
Step1: Click “Network” “DDNS”, and check “DDNS Enable”.
Step2: Select the host name you applied for a DDNS service in “System Name”
(ex. dyndns).
Note: You need to create a DDNS account from a website which provides free DDNS
service. For details, please refer to “Fehler! Verweisquelle konnte nicht
gefunden werden.” at page 12.
Select the system name you set when subscribing the DDNS service from
the drop-down list, for example, dyndns.
Enter the user name & password you used to log into the DDNS service.
Then, enter the host name you set when subscribing the DDNS service,
for example, headoffice523.
Step3: Click “Save” and log out. Then, disconnect your camera and your PC, and connect
them to Internet separately.
Step4: Enter the host name you just note down in the URL address box of the web browser,
and see if you can access the camera successfully.
Page 14
14
APPENDIX 1 CREATING AN ACCOUNT FOR DDNS SERVICE
For PPPOE or DHCP, you should enter the host name which points to the IP address of your
network camera for login first.
There are many websites for free DDNS service application, and below shows an example of
DDNS account application from the website http://www.dyndns.com.
Step1: Go to http://www.dyndns.com, and click “Create Account” to sign up a DDNS account.
Step2: Enter all the information necessary for signing up an account according to the website
instructions.
‧Key in a user name for login, for example, headoffice523.
‧Set the password and input it again to confirm.
‧Key in your E-mail address and input it again to confirm.
Then, click “Create Account”.
Step3: The system will automatically send a confirmation email to your email account. Please
read this email within 48 hours and complete the procedure to activate your account
according to the instructions in the email.
Page 15
15
When the account is confirmed, you will see “Account Confirmed”. Your account is
created successfully now.
Step4: Click “login”, and enter the user name and password you preset before to log in.
Step5: Click “Add Host Services”.
‧Input a meaningful host name.
‧Choose a host system name.
‧Enter the IP address you want to redirect.
Note down the whole host name, for example, headoffice523.dyndns.org. Then, click
“Add To Cart” for billing.
Note: This service is free. Just finish the billing process, and NO paying information is
required.
Step6: Click “Activate Services” after checkout, and you’re ready to use DDNS services now.
Page 16
16
APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES
EagleEyes is a mobile phone program used with our surveillance system (DVRs or network
cameras) for remote surveillance. It has several advantages:
It’s free (Except EagleEyes Plus for iPhone).
It’s compatible with several popular mobile platforms, such as iPhone, BlackBerry, Symbian,
Windows Mobile and Android.
It’s easy to download, install and configure. For more details about configuring and operating this
program, please visit our official website www.eagleeyescctv.com.
A2.1 Prerequisites
Before installing EagleEyes to your mobile phone for remote surveillance, make sure you have
checked the following:
Your mobile platform is iPhone, BlackBerry, Symbian, Windows Mobile & Android.
Mobile Internet services are subscribed and available to use for your mobile phone.
Note: You might be charged for Internet access via wireless or 3G networks. For the
Internet access rate details, please check with your local network operator or service
provider.
Your DVR or network camera is powered on and connected to Internet.
You have noted down the IP address, port number, user name and password used
to access your DVR or network camera from Internet.
A2.2 Where to download
Connect to www.eagleeyescctv.com from your mobile phone, and sign in.
Note: Please DO NOT try to download EagleEyes from your computer.
Then, select “Software” and the mobile platform of your phone to download
EagleEyes to your phone.
For BlackBerry, Symbian, Windows Mobile & Android, select the download link from the website to start
downloading.
Note: It’s recommended to download EagleEyes for BlackBerry with the web browser of
Opera.
For iPhone, two versions of EagleEyes are available:
-- EagleEyes Plus (US$4.99), and
-- EagleEyes Lite (Free).
Select the version you want, and you’ll be directed to “App Store” to download the application.
Note: You can also find EagleEyes on “App Store” from your iPhone. Go to “App Store”, and
select “Search”. Enter the keyword “eagleeyes” to find and download the version you
want.
Page 17
17
When the download is completed, EagleEyes will be installed automatically to
the location where all applications are saved in your phone by default, or where
you specify.
Note: For more details about configuring and operating this program, please visit our
official website www.eagleeyescctv.com.
Loading...