Digitrax RF24 Users Guide

Transceiver Certification Test Report
FCC ID: LV3RF24
IC: 3015A-RF24
FCC Rule Part: 15.249
ACS Report Number: 07-0262-15C
Manufacturer: Digitrax Inc.
Model: RF24
Installation Guide
5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598
D
D
RRuunn YYoouurr TTrraaiinnss,, NNoott YYoouurr TTrraacckk!
iiggiittrraax
C
x
C
oommmmaannd
C
oonnttrrool
d
C
l
!
RF24
Digitrax Host Device
2mm 10 Pin connector
RF24 Radio Transceiver Module
2.4 GHz Duplex Communications Module Fits Digitrax Host Devices
80 foot range
Plug N’ Play Installation
FCC/IC Info Label
RF24 Module
FFeeaattuurreess:
n Duplex LocoNet RF Module for Digitrax Host devices n FCC Part 15, Class B RFI compliant
PPaarrttss LLiisst
1 RF24 Radio Module 1 This Instruction sheet
IInnssttaallllaattiioon
1 Align RF24 module with 10 pin socket facing and matching the Host device plug orientation at the board edge. 2 Plug in the RF24, ensuring that the 10 pins of the socket exactly align with the 10 pin Host connector 3 Apply power to the Host, and the RF24 module will be recognized and oper­ate. That is all that is required to install this Plug N’Play device!
4. If the RF24 green LED does not blink when power is applied, contact Digitrax Techical support.
©2007 Digitrax, Inc www.digitrax.com 1
:
t
n
RF24 Transceiver Module
Fits Digitrax Host Devices
Warning: Changes or modifications to this device not expressly approved by Digitrax Inc. could void the user’s authority to operate the equipment.
FCC Information: (FCC Module ID: LV3RF24)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal­lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to cor­rect the interference by one or more of the following measures:
n Reorient or relocate the receiving antenna n Increase the seperation between the equipment and the receiver n Connect the equipment into an outlet on a circuit different from that to which
the receiver in connected
n Consult a dealer on an experienced radio/TV technician for help.
Industry Canada Information: (IC ID: 3015A-RF24)
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the follow­ing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l'in­terférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'inter­férence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée. This class B digital apparatus complies with Canadian ICES-003. Cet appareillage numérique de la classe B est conforme à la norme NMB-o003 du Canada
450 Cemetery Street Norcross, GA USA 30071
www.digitrax.com
T 770-441-7992
Made in U.S.A.
F 770-441-0759 E sales@digitrax.com
1k/06/07
307-RF24 -INS
Loading...