Digital Watchdog Starlight D1363D User Manual

Starlight D1363D
11192010
User Manual Version #2: Camera with ICON Menu
PRECAUTIONS
Do not open or modify.Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages.Do not put objects into the unit.Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages.Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration.Do not install near electric or magnetic fields.Protect from humidity and dust.Protect from high temperature.Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.Cleaning To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe. Mounting SurfaceThe material of the mounting surface must be strong enough to support the camera.
TROUBSHOOTING
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the menu setup of the camera. Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful interference .when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacture.
FEATURES
1/3” Sony Super HAD II CCD
High Resolution 560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
Electronic Day and Night
Star-Light (Super Low Light Technology)
DRC (Dynamic Range Compressor)
Dark spots in images particularly become more visible without overexposing the bright spots to create one perfect image.
3D-DNR (3D Digital Noise Reduction)
Produces less noise and more color during low-light application.
HME (Highlight Mask Exposure)
Masks overly exposed light to produce a true video image of any environment.
BLC (Back Light Compensation)
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
No Fog or Condensation under Any Weather Condition
Power Wire Maximum Distance
Wire Gauge 12VDC 24VAC
24 AWG 80ft 323ft 22 AWG 128ft 513ft 20 AWG 203ft 815ft 18 AWG 323ft 1295ft 16 AWG 514ft 2056ft 14 AWG 816ft 3264ft 12 AWG 1295ft 5183ft 10 AWG 2057ft 8228ft
DIMENSION (mm) & POWER REQUIREMENT
POWER REQUIREMENT:
12VDC @1A 24VAC @ .500mA
COAXIAL CABLE TYPE MAXIMUM DISTANCE
RG59/ U 750feet RG6/U 1,000feet RG11/U 1,500feet
INSTALLATION
Included with DW Indoor Dome Camera:
1. User Manual
2. Mounting Template
3. Security L-Key
4. Single Sided Hex Key
5. Secondary BNC Cable for a Field Monitor
6. Two (2) Screws and Two (2) Dry Wall Anchors
1
2
3 4
5
6
Camera Installation
Use the mounting template to mount the camera. Using the security L-key to loosen the four screws that secure the
vandal proof dome cover, Remove the vandal proof dome cover to access the screw holes to mount the camera.
NOTE: Keep the lens and the vandal proof cover free from dust or fingerprint.
INSTALLATION
A. Loosen the fixing screw using the L-Wrench. B. Separate the upper case and base case. C. Loosen the inner screws using a screwdriver. D. Detach the gimbal from the base case. E. Cut a hole in the ceiling for routing the cables. F. Place the camera horizontally on the ceiling.
Drill the screw holes at the marked two positions.
G. Pass the power cable and video cable from the
camera unit through the cable hole in the ceiling.
H. Align the screw holes of the camera unit with the
holes in the ceiling.
Secure the camera with the two screws. I. Fix the gimbal to the base. J. Install and adjust the camera unit. K. Adjust the dome to show the lens through the
camera window. Attach to the base. L. Put the upper case and the base together M. Tighten the screw to fasten the upper case and
base case.
Loading...
+ 11 hidden pages