Quick Start Guide
DWC-PZV2M72T
WHAT’S IN THE B OX
QSG Manual 1 Set
Screw & Plast ic
Anchor – 4pc s
1 Set
Manual CD 1 Set Torx Wren ch 1 Se t
Template Sheet 1 Set
Username: admin Password: admin
Attention: T his document is inte nded to serve as a quic k reference page for i nitial set-up.
It is recommend ed that the user read th e entire instruc tion manual for comp lete and proper cam era usage.
Tel: 866-446 -3595 / 813-888 -9555
Technical Support Hou rs: 9:00AM – 8:00PM E ST, Monday thru Friday
digital-watchdog.com
Quick Start Guide
Step 1 – PREPARING TO MOUNT THE CAMERA
Step 3 – INSTALLING THE CAMERA MODULE
Step 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
1. Using the mounting tem plate sheet or the camera itself, mark an d drill the necessary hol es in the wall
or ceiling.
2. For the installation process, remove t he dome cover from the camera modu le by loosening the screws
on the dome. Use the wrenc h provided with the camera.
5. Assemble the dome cover over the c amera body and detach the protecti ng film from the dome bubble.
3. Pass the wires through the mount b racket and make all necessar y connections.
a. NETWORK CO NNECTIONS – If you are using a PoE Swi tch, connect the camera using an Ethe rnet
cable for both data and p ower.
b. NETWORK CONNECTI ONS – If you are using a non-PoE switch, conn ect the camera to the switch
using an Ethernet ca ble for data transmission and use a po wer adapter to power the camera.
NOTE: If you plug the camer a into PoE+ but then plug that switch into a regular Po E it will not work.
Power Requirements Power Consumption
DC 12 V
PoE IEEE 802.3atP oE+ / PoE Class 3
12VDC: 22.5W
PoE+: 25.5W
Resetting the camera: To reset the camera, use the tip of a paper clip or a p encil and press the
reset button. Pressin g the button for five (5) seconds will initia te a camera-wide reset of all the settings,
including netwo rk settings.
1
2
3
Template
Sheet
Reset Button
Power
Network
Connection
4. To use the camera’s water proof w iring:
(1)
. Install the L AN cable into (a).
(2)
. (b) will be assembled to (a) with a 1/4 turn.
(3)
. Thread (c) tightly to (b).
a
b
c
Step 5 – DW IP FINDER
™
Use the DW IP Finder™ included in the cam era’s accessory CD to scan the netwo rk and detect all MEGApix®
cameras. Use the DW IP Finder™ to set the camera’s network s ettings, perform firmware u pgrade or access
the camera’s web client.
Quick Start Guide
Rev Date: 02/16 Copyright © Dig ital Watchdog . All rights r eserve d. Specifi cations and p ricing are subj ect to change wi thout notic e.
Step 6 – WEB VIEWER
Once the camera’s netw ork settings have been setup prop erly, you can access the camera’s web viewer
using the DW IP Finder. To open the camera’s web viewer:
1. Find the came ra using the DW IP Finder.
2. Double-click on the cam era’s view in the results table.
3. Press the ‘View Camera Web site.’ The came ra’s web viewer will open up in your default web
browser.
4. Enter the camera’s username a nd password (default are admin / admin).
5. If you are accessing the c amera
for the first time, install th e ActiveX
files in order to view vide o from the
camera.
Network Setup
1. Run the CD included w ith the camera and click on the DW IP Finder™ file.
2. T he software will scan your net work for all supported came ras and display the results in the tab le. Allow up
to 5 seconds for the IP Inst aller to find the camera on the netwo rk.
3. You can pres s the ‘Refresh List’ to search the net work again, or filter the search resul ts by entering a value
in the filter box at the botto m of the page.
4. Ch eck the box next to ‘Display Camera T humbnail’ to view a JPEG image of the cam era’s view next to the
camera name on supported models.
5. Se lect a camera from the list by double-c licking on it. The camera’s network i nformation will appear.
If necessar y, you can adju st the camera’s network type.
6. The camera’s default network information is:
7. To view the camera’s web vi ewer, click on ‘View Camera Website.’
8. To save the cha nges made to the camera’s settings, input t he ID
and PW of the camera for a uthentication and click ‘Save’.
9. If the camera needs to be reb ooted after the settings were chan ged, press the ‘Reboot’ button.
The camera will cycl e power and will appear back in the sea rch results once the reboot is complete.
10. To update the camera’s firmware fro m the DW Desktop Tool™, click on the firmware t ab, upload the
firmware file and sele ct the cameras to update. You can update multiple came ras at the same time.
Step 4 – ADJUSTING THE CAMERA’S SENSORS
The camera’s four indivi dual sensors can be rotated and tilted to ad just the camera’s views using the
motorized options in the c amera’s web viewer.
Select DHCP if the in ternet service is dy namic IP. This will allow the camera to re ceive its IP address
from the DHCP serve r.
Select STATIC to manually enter t he camera’s IP address, subn et mask, Gateway and DNS i nformation.
Contact your network administrator for more information.
Default TCP/IP information
• IP: 169.254.X.X • Gateway: 192.168.1.1
• Subnet Mask: 255.255.2 55.0 • DNS: 168.126.63.1
‘Port Forwardin g’ has to be set in your netw ork’s router for
external access to the c amera.
Default ID / PW : admin / adm in
Server Minimum Requirements
Processor Intel® Core ™ i3-3220 CPU @3.30GHz or similar
RAM 8GB Required (16GB Recommended)
Hard Drive Sata 6 Gb/s, 64 MB cashe, 1 TB, 7200 RPM
Client Minimum Requirements (for a single 4K resolution video monitor)
Processor Intel® Core™ i5-2500 CPU @3.3 GHz or similar
RAM 8GB Required (16GB Recommended)
Graphic Card NVIDA Quadro K6000, 1GB DDR3 or similar
SERVER AN D CLIENT REQUIREMENTS
Loading...