Quick Start Guide
Quick Start Guide
DWC-MV72Wi4A / DWC-MV72Wi28A
Username: admin Password: admin
NOTE: It is highlighy recommended to change the admin’s default
password after installation.
WHAT’S IN THE BOX
QSG Manual 1 Set
Mount Bolt &
Nut – 2pc s
1 Set
STEP 1 – PREPARING TO MOUNT THE CAMERA
1. The mounting surface must bear ve times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover
to be damaged. This may cause a breakdown or re.
3. For the installation process, remove the dome cover from the camera module
by loosening the three (3) screws on the dome. Use the wrench provided with
the camera.
4. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
5. Pass the wires through the mount bracket and make all necessar y
connections.
a. NETWORK CONNECTIONS – The camera supports a PoE power
connection. Use a PoE Switch to connect the camera using an Ethernet
cable for both data and power.
Power Requirements Power Consumption
POE IEEE 802.3af Class2 Max. 5.2W
STEP 3 – INSTALLING THE CAMERA
1
3
5
3
7
Template Sheet
2
4
6
Test Video
Cable
Template Sheet
for installing by
Bolt & Nu t
Waterproof
Cap
NOTE: Download All Your Support Materials and Tools in O ne Place
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search yo ur product by ente ring the part n umber in the ‘Search by Product’ search
bar. Results for applicable part num bers will populate auto matically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals, Quick Start Guide s
(QSG), soft ware and rmware will ap pear in the resu lts.
Attention: This document is intended to ser ve as a quick reference for ini tial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
Tel: 866-446 -3595 / 813-888-9555
Screw & Plast ic
1 Set
Anchor – 2pcs
1 Set Tor x Wre nch 1 Set
1 Set
digital-watchdog.com
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
1 Set
6. Attach the main body to the mount bracket by tightening the lock screw
using the six-angle wrench.
7. To use the camera’s water proof wiring:
(1). Install the LAN cable into .
b
(2). will be assembled to with a 1/4 turn.
(3). Thread tightly to .
c
a
a
b
a
b
c
Note: To ensure moisture seal, make sure the o-ring is in place between
(a) and (b). In extreme environments use of an outdoor rated sealer
is recommended.
Note: When using the waterproof cap, crimp the RJ45 connector after
passing the cablie through the waterproof cap.
8. Use the camera’s 3-Axis gimbal to adjust the camera’s tilt and angle. The
camera’s maximum tilting angle is 70.
9. Assemble the dome cover over the camera body and detach the protecting
lm from the dome bubble.
8
9
Reset Button
Resetting the camera: To reset the camera, use the tip of a paper clip or
a pencil and press the reset button. Pressing the button for five (5) seconds
will initiate a camera-wide reset of all the settings, including network settings.
Quick Start Guide
STEP 3 – INSTALLING THE CAMERA (CONT.)
Installation using Mount Bolt and Screws:
1. Using the template sheet, make and drill the cabling holes on the wall/ceiling.
2. Secure the two long mounting screws to the camera’s base.
3. Pass the wires through the mount bracket and make all necessar y
connections.
4. Mount the camera to the mounting surface by using the 2 mounting nuts.
Rotate the locking discs over the screws until the camera is held tightly from
the mounting surface.
NOTE: The camera’s maximum tilting angle is 70°
STEP 6 – DW IP FINDER
™
Use the DW IP Finder™ software to scan the network and detect all MEGApix®
cameras, set the camera’s network settings or access the camera’s web client.
Network Setup
1. Go to: http://www.digital-watchdog.com
2. Search for ‘IP Finder’ on the quick search bar at the top of the page.
3. The latest IP Finder sof tware will appear in the search results. Click on the
link to download the le to your computer.
4. The software will scan your network for all supported cameras and display
the results in the table. Allow up to 5 seconds for the IP Finder to nd the
camera on the network.
Camera Name,
Model, IP Address,
and MAC Address
Search for Cameras
Filter Search Results
Cam era’s
Network Settings
Vie w Cam era’s
Thumbnail View
Camera Uptime
Cam era’s Firmware
Open Camera’s IP
Conguration Screen
7. To view the camera’s web viewer, click on ‘View Camera Website’.
‘Port Forwarding’ has to be set in your network’s router for external access
to the camera.
8. To save the changes made to the camera’s settings, input the ID and PW of
the camera for authentication and click ‘Save’.
9. If the camera needs to be rebooted after the settings were changed, press
the ‘Reboot’ button. The camera will cycle power and will appear back in the
search results once the reboot is complete.
Default ID / PW : admin / admin
NOTE: It is highlighy recommended to change the admin’s default
password after installation.
STEP 7 – WEB VIEWER
*
STEP 4 – CABLING
Use the diagram below to properly connect power and network to the camera.
Using a PoE Switch or PoE Injector
NETWORK
CONNECTION
STEP 5 – MANAGING THE SD CARD
This camera does not support local SD card integration.
Firmware Upgrade
5. Select a camera from the list by double-clicking on the camera’s image
or clicking on the ‘Click’ button under the IP Conf. column. The camera’s
network information will appear. If necessary, you can adjust the camera’s
network type.
Select DHCP if the internet ser vice is dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Contact your network administrator for more information.
6. The camera’s default network
information is:
Default TCP/IP information
• IP: DHCP
The GUI d isplay m ay dif fer by ca mera mo dels.
Once the camera’s network settings have been setup properly, you can access
the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will open up
in your default web browser.
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera for the rst time, install the VLC player for
web les in order to view video from the camera.
*
NOTE: Some Menu options may not be available based on the camera
model. See the full manual for more information.
NOTE: Please see the full product manual for web viewer setup,
functions and camera settings options.
Rev Date: 05/18
Specications and pricing are subject to change without notice.
Copyright © Digital Watc hdog. A ll righ ts reserved.
Loading...