Digital Watchdog MEGApix DWC-MV72Wi28A, MEGApix DWC-MV72Wi4A User Manual

User Manualer. 5/

nBefore installing and using the camera, please read this manual carefully.stalling and using the camera, please read this manual carefully.
to keep it handy Be sure to keep it handy for future reference.for future reference.

MApi 2.1MP Indoor/Outdoor
Vandal Dome IP Camera with
Built-in Microphone

DWC-MV72Wi28A
DWC-MV72Wi4A

Index

INTRODUCTION

Important Safety Information
Features

Part Name

Dimensions
Product & Accessories

03
06
07
08
09

INSTALLTION

Disassemble the Camera
Installation
Insatallation using Mount Bolt & Nut
Cabling

10
11
12
14

NETWORK SETUP

IP Installer
Quick Start of Network Connection DDNS
Registration
Guide to Network Environment Setup Case (A~D)
Port Forwarding
Starting IP Camera

15
16
17
18
21
22

Video & Audio Setup
Camera Setup
Network Setup
Trigger Action Setup
Events Setup
Security Setup
System Setup

24

32
39
49
52
56
63

APPENDIX

Current TCP/IP Settings
Changing IP Address and Subnet mask

Specifications

FAQ

Warranty
Limits & Exclusions

72
73
74
75
76
77

WEB VIEWER SCREEN

23 Basic Screen

SETUP

2

Safety Information

This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.

Warning Precaution

This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

:

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.

WARNING

Be sure to use only the standard adapter that is specified in
the specification sheet. Using any other adapter could cause
fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to the
product.

Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation
or fire.

Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.

When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.

Do not place conductive objects (e.g. screw drivers, coins,
metal items, etc.) or containers filled with water on top of
the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.

If any unusual smells or smoke come from the unit, stop
using the product. Immediately disconnect the power sorce
and contact the service center. Continued use in such a
condition may cause fire or electric shock.

If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.

When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock.

WARNING

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Precaution

Operating

• Before using, make sure power supply and all other parts are

properly connected.

• While operating, if any abnormal condition or malfunction

is observed, stop using the camera immediately and contact

your dealer.

Handling

• Do not disassemble or tamper with parts inside the camera.

• Do not drop the camera or subject it to shock or vibration as

this can damage the camera.

• Clean the clear dome cover with extra care. Scratches and

dust can ruin the quality of the camera image.

Installation and Storage

• Do not install the camera in areas of extreme temperature,

exceeding the allowed range.

• Avoid installing in humid or dusty environments.

• Avoid installing in places where radiation is present.

• Avoid installing in places where there are strong magnetic

• Avoid installing in places where the camera would be subject

to strong vibrations.

• Never expose the camera to rain or water.



Important Safety Instructions

1. Read these instructions. - All these safety and operating instructions should be read before the product is

installed or operated.

2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use instructions should be followed.

5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet

basement; near a swimming pool; etc.

6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and

openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s unstructions have been adhere to.

8.

that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11.

12.

manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14.

in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.

4

Disposal of Old Appliances

1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately form the municipal waste
stream stream in accordance to laws designated by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.

waste disposal service or the shop where you purchased the product.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interferenece at his own expense.



 2.1MP 1/2.7" Image Sensor at Real-time 30fps
 2.8mm and 4mm Fixed Lens Options
 True Wide Dynamic Range (WDR)
 Dual Codecs (H.264, MJPEG) with Simultaneous Streaming
 50' Smart IR™ with Intelligent Camera Sync
 Audio Input with Built-in Microphone
 Smart DNR™ 3D Digital Noise Reduction
 True Day/Night Mechanical IR Cut Filter
 Programmable Privacy Zones
 Auto Gain Control (AGC)
 Backlight Compensation (BLC)
 Auto White Balance (AWB)
 Motion Detection
 Web Server Built-in
 PoE Class 2
 ONVIF Conformant, Profile S
 IP64 Certified Dust and Splashing Water Resistant
 IK10-Rated Impact-Resistant
 5 Year Warranty

Features

Introduction-

6

Part Name

Introduction -

Dome Cover

Reset Button

Gimbal

IR Switch

Bottom Case

RJ-45 Cable

Test Monitor Cable

Connector

MIC

IR LED

Lens

7

Unit: Inch (mm)

Dimension

ations -

4.1" (105mm)

1.28" (32.5mm)

1.11" (28.2mm)

8

Product & Accessories

Introduction -

Template Sheet

for Installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plastic Anchor-2pcs

Torx Wrench

Test Monitor Cable

Waterproof cap & Gasket

Camera

Cables

Quick Manual &
Download Guide

9

Installation -

Disassemble the camera

Before installing your camera, you have to read the following cautions.

. The mounting surface must bear fie times the weight of your camera.

. Do not let the cables get caught in improper places or the electric line coer to be damaged. This may
cause a breakdown or fire.

. For the installation process, remoe the dome coer from the camera module by loosening the three
 screws on the dome. se the wrench proided with the camera.

To re-attach the dome to the camera base, match the

one screw hole on the dome cover and camera
bottom specially.

Reset to the Factory Default

Press the reset button for 5 seconds to return the setup
to the factory default.

Warning:

If you press the ‘Reset’ button, you will lose all setting
data. If needed, please, make a note for further installation.

Reset Button



Installation

Installation -



Step 3 – INSTALLING THE CAMERA

6. Attach the main body to the mount bracket by tightening the lock screw

using the six-angle wrench.

7. To use the camera’s water proof wiring:

(1). Install the LAN cable into .

with a 1/4 turn.

Note: To ensure moisture seal, make sure the o-ring is in place between

(a) and (b). In extreme environments use of an outdoor rated sealer
is recommended.

a

b

c

a

(2). b will be assembled to

a

(3). Thread tcightly to .

b

Step 1 – PREPARING TO MOUNT THE CAMERA

Step 2 – CABLING THE CAMERA TO EXTERNAL DEVICES

1. The mounting surface must bear ve times the weight of your camera.

2. Do not let the cables get caught in improper places or the electric line cover

to be damaged. This may cause a breakdown or re.

3. For the installation process, remove the dome cover from the camera module

by loosening the three (3) screws on the dome. Use the wrench provided with
the camera.

4. Using the mounting template sheet or the camera itself, mark and drill the

necessary holes in the wall or ceiling.

5. Pass the wires through the mount bracket and make all necessary

connections.

a. NETWORK CONNECTIONS – The camera supports a PoE power

connection. Use a PoE Switch to connect the camera using an Ethernet
cable for both data and power.

Power Requirements

POE IEE E 802.3af Cla ss2

Power Consumption

Max . 5.2W

NETWORK

CONNECTION

8. Use the camera’s 3-Axis gimbal to adjust the camera’s tilt and angle. The

camera’s maximum tilting angle is 70.

9. Assemble the dome cover over the camera body and detach the protecting

film from the dome bubble.

1

9

8

6

Template Sheet

7

4

5

Installation -

Installation Using Mount Bolt & Nut

Template Sheet

1

Disassemble the camera. See the section ‘Installation ­Disassemble the camera’ for details.

Using the template sheet, make the cabling holes on
the ceiling panel.

Insert the 2 mount bolts into bottom case of camera.

3

2

2

Installation -

Installation Using Mount Bolt & Nut

5

Insert the mount bolts into template holes after
connecting the cable.

Fix the bottom case by tightening mount nuts to
mount bolts on the ceiling panel.

4

7

8

6

To achieve desired view direction and orientation,

Attach the dome cover to the bottom case.

stopper screw.



Cabling

Installation -

Use a PoE-enabled switch to connect data and power through a single cable and begin viewing and recording images instantly.

Ethernet cable

1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing transmission of

power and data via a single Ethernet cable.

power, record, or control the camera. Follow the illustration
below to connect the camera to a PoE-enabled switch using
an Ethernet cable.

4

Network Setup -

DW IP Finder™

To save the changes made to the camera's settings, input ID and
PW of the camera for authentication.

If the camera needs to be rebooted after the settings were changed,
press the 'Reboot' button. The camera will power cycle and will
appear back in the search results once the reboot is complete.

Click ‘Save’ to save changed values.

To update the camera's rmware from the DW IP Finder™,
click on the rmware tab, upload the rmware le and
select the cameras to update. You can update multiple
cameras at the same time.

Select ‘DCP’ if the internet serice is dynamic IP to allow the
camera’s network information to be filled out automatically.

Select ‘Static’ to manually enter the camera’s network
information. ou can adjust the camera’s network type, IP
address, subnet mask, Gateway and DS information.

Contact your network administrator for more information.

The cameras default network information is:
Default TCP/IP information

- IP: DCP

A ‘Port Forwarding’ has to be set in your network’s router for
external access to the camera.

Default ID / PW : admin / admin



 To view the camera's web client, click on 'View Camera Website'.

 Go to: http://www.digital-watchdog.com

 Search for ‘IP Finder’ on the quick search bar at the top

of the page.

 The latest DW IP Finder™ software will appear in the

search results. Click on
the link to download the file to your computer.

 The software will scan your network for all supported

cameras and display the results in the table. Allow up to 5
seconds for the DW IP Finder™ to find the camera on the
network.

5 Check the bo net to Display Camera Thumbnail to

iew a PG image of the cameras iew net to the
camera name on supported models.

 Select a camera from the list by double-clicking on the

camera’s image or clicking on the ‘Click’ button under the
IP Conf. column. The camera’s network information will
appear. If necessary, you can adjust the camera’s
network type.

Quick Start of Network Connection

Network Setup -

Please follow the steps below to complete
the initial setup of the network function.

1.

Open the IP Installer on a PC, then search for the IP camera.

If multiple numbers of camera are connected it should be
distinguished by the mac address of the Camera.

Click the Camera IP, and connect to the WEB PAGE.

2.

3.

4.

Default ID/Password to access IP Camera are both the
word: admin.

5.

Familiarize yourself with the Viewer Interface Screen.6.

please install VLC to display live video.7.

The IP setting can be set to ‘STATIC’ at IP Installer or web
viewer followed by Setup -> Network -> TCP / IP.

8.

If you have a DHCP server, it will automatically set the Camera IP.

If you do not have a DHCP server, Camera IP is set to 192.168.1.80
after one minute. In this case, PC IP must be changed to the IP to
be able to access the 192.168.1.80.

Please do not power on the IP Camera until instructed.

Explorer.

If connecting the IP Camera directly to a modem, power down
and reset the modem. Leave the modem powered down until
con tions ar nalized with the IP Camera and the IP Camera
has been correctly connected to the modem.

If the IP Camera is connected to a network which utilizes a
router, you must have Port Forwarding co ured on your
personal router to forward all ports to the IP address you
have assigned the IP Camera.

(if necessary), you may access your IP Camera on your local
network by opening Internet Explorer and specifying the IP
address and Web Port that you have assigned to the IP
Camera.

9.

10.

Example: http://192.168.0.200:8888

If you leave your Web Port set to 80, you don’t need to specify
the port in the Address Bar to access to your IP Camera.

Access your IP Camera via the Internet :

If you use a static IP address assigned by your ISP

1) Open Internet Explorer.

2) Type the IP of the IP Camera.

3) If you use a router, type the routers’ static IP and the web port
number of the IP Camera.

If you have a dynamic address provided by your ISP

1) Open Internet Explorer and visit the DDNS website.

2) Register the IP Camera.

3) Reboot the IP Camera.

4) Give the DDNS server 10 minutes to locate your IP Camera’s
IP information.

5) Click the refresh button in the Internet Explore.

6) After your camera is connected, select your camera.

11.

16

DDNS Registration

Network Setup -

If you have DYNAMIC IP service from your
Internet Service Provider (ISP), you can’t tell
the current IP address of the IP Camera.
To solve this problem, you have to register to
our DDNS service.

A

t, you have to check if you are using
dynamic addressing. If so, register your IP
Video Server on our DDNS website before you
c

re, setup, or install the IP Camera.

Even though your IP is not dynamic, you will

just remember ‘hostname.dyndns.com/gate1’
instead of complicated series of numbers like
http://201.23.4.76:8078.

For more details, contact our Support Center.

To use a public DDNS called ‘dyndns’ or ‘no-ip’, refer to the detail
information on how to use the service.
(Visit the web site : http://www.dyndns.com or
http://www.no-ip.com)

17

Guide to Network Environment

Network Setup -

Please congure the IP Camera at the
installation site. You must determine your
network scenario in order to congure the IP
Camera with the proper TCP/IP settings.
This tutorial will guide you through the
process. Before actually conguring the IP
Camera, determine settings to be applied.
Record those settings to be used to congure
your IP Camera for reference.

When conguring your IP Camera, treat the
IP Camera as another PC on your network.
You will assign it several addresses and other
TCP/IP properties to match your current
network.

This step-by-step tutorial will teach what IP
addresses and network congurations should
be assigned based on the network scenario.

If you were not given any IP addresses or the ISP was responsible
for the setup and installation of your Internet connection, go to
step 2.

If you are not using a router on your network, your ‘Current TCP/IP
Settings’ (from the previous section) and ‘Assigned IP Addresses
from My ISP’ will be exactly the same.

Before you begin, locate any information and settings
received from your Internet Service Provider (ISP). You may
need to refer to these IP addresses at a later time during the
conguration.

1.

You must determine whether the IP address is STATIC or
DYNAMIC. At this moment, you are only concerned about the
ISP. Did they provide you with a STATIC or DYNAMIC address?
If you are unsure, contact your I S P.

Congure your IP Camera’s TCP/IP settings for network
connectivity by selecting Setup from the main interface and
selecting TCP/IP located on the left of the Setup screen.

If prompted for ID and Password, use ‘a dmin’ for both entries.

The default web port number is 80. If port 80 is blocked by
the ISP, a value between 1025 ~ 60000 should be used. If TCP
port 80 is blocked, consult the ISP

2.

3.

4.

Current TCP/IP Settings

IP Address

Subnet Mask

Default Gateway

Primary DNS Server

Secondary DNS Server (Option)

Static Dynamic

5. The following descriptions are several basic network
scenarios. Determine which scenario describes your network.
If your network does not match one of the scenarios below
and you are unsure how to setup your IP Camera, contact
your network administrator and then call our Support Center.

You cannot control the rectangular gray areas and only the ISP
has access to the devices.

18

Setup Case A, B

Network Setup -

Case A:
Dynamic IP +
Personal Router [Most SOHO]

Personal Router
W/Intergrated Switch

Cable/xDSL Modem
(ISP Provided)

Phone Line

or CATV

PC

Internet

Case B:
Static(Fixed) IP +

PC

Personal Router
W/Intergrated Switch

Gateway or Router
at ISP

Public Line

Internet

as follows :

STAT IC (even though you have Dynamic IP from
your ISP, use STATIC on the IP Camera)

Network Type :1.

A private IP address such as

192.168.0.200 (Example)

Internet Address :2.

You need to assign an IP address to the IP Camera just as you do
with PC.

The IP address you assign must be unique to your network and
match your network as well. For information on how to choose
a unique IP and match your network, read the FAQ.

The IP address you assign must be a private IP. Fo r information
on how to choose a private IP please, read the FAQ.

255.255.255.0 (Example)

192.168.0.1 (Example)

Subnet Mask :3.

You must use the same subnet mask as the one you noted under
‘Current TCP/IP Settings’.

Default Gateway :4.

This IP address must be the IP address of your router.
(private or LAN side)

Use the same Default Gateway you noted under ‘Current TCP/IP
Settings’.

Use the 1st DNS Server from ‘Assigned IP
Address from My ISP’.

Preferred DNS Server :5.

Use the DDNS server.

DDNS Server :6.

This is the same site you will register later to accommodate
dynamic IP from your ISP.

8888Web Port :7.

Do not use the default port 80 as this number must be changed.

You may select any number between 1025 ~ 60000.

If you did not receive any IP addresses from your ISP, contact
the ISP and acquire the IP address of their DNS server.

Camera

Camera

19

Setup Case C, D

Network Setup -

To connect the IP Camera directly to a modem, power down
and reset the modem. Leave the modem powered down until

Camera has been connected correctly to the modem. Then
power on the modem, followed by the IP Camera.

Cable/xDSL Modem
(ISP Provided)

Phone Line

or CATV

Internet

Internet

Public Line

Gateway or
Router at ISP

STATICNetwork Type :1.

A static IP address received from your ISP such
as 24.107.88.125 (Example)

Internet Address :2.

You need to assign an IP address to the IP Camera just as you do
with PC.

Subnet mask assigned from your ISP such as

255.255.255.240 (Example)

24.107.88.113 (Example)

Subnet Mask :3.

Default Gateway :4.

Use the assigned default gateway from your ISP

Use the 1st DNS Server from ‘Assigned IP
Address from My ISP’

Preferred DNS Server :5.

Use the DDNS server

DDNS Server :6.

This is the same site you will register later to utilize our DDNS
service.

80Web Port :7.

You may select any number between 1025 ~ 60000.

If you have not received any IP addresses from your ISP, contact
them to acquire the IP address of their DNS server.

DYNAMICNetwork Type :1.

Use the DDNS serverDDNS Server :2.

This is the same site you will register later to accommodate
dynamic IP from your ISP.

80Web Port :3.

You may select any number between 1025 ~ 60000.

as follows :

as follows :

Case C:
Static(Fixed) IP [Dedicated line directly
to the IP Camera]

Case D:
Dynamic IP + DSL/Cable Modem [Connected

directly to the IP Camera]

Camera

Camera

20

Port Forwarding

Network Setup -

After entering the correct TCP/IP settings, you
are ready for ‘Port Forwarding’(Cases A, B).

Please record the TCP/IP settings of your IP Camera for future
reference. You may need this information to access your IP

1.

After clicking ‘Apply’, the system will prompt for a reboot.
Please allow the system 50 seconds to reboot and accept the
changes. After 50 seconds, close the con

ration screen.

The view will display ‘Trying to Reconnect’. If the ACTIVE light

, the IP Camera has rebooted. After the system
reboots completely, remove the power supply from the
unit and close Internet Explorer.

Return your PC/Laptop TCP/IP properties to their original
settings.

Before installing the IP Camera, you must use ‘Port
Forwarding’ on your personal router (Cases A, B).

You will need to forward 1 ports:

• Web Port

All the ports will be forwarded to the IP address you
assigned to the IP Camera.

In the example above, you would forward:

• 8888 192.168.0.200

2.

3.

4.

IP Camera TCP/IP Settings

IP Address

Subnet Mask

Default Gateway

Preferred DNS Server

DDNS Server

Web Port

For information on how to use ‘Port Forwarding’, please read
Appendix C.

21

Starting IP Camera

Network Setup -

After forwarding correctly the Web Port,
through your router (if applicable), install the
IP Camera in a proper location.

Locate the serial number located on the label attached to the
bottom of the IP Camera, you will need this for DDNS
registration.

Connect the IP Camera to your router or cable/DSL modem
(per your network scenario) via a Cat5/5e UTP Ethernet
network cable.

Supply power to the IP Camera.

After 1 minute, the IP Camera will operate.

(if necessary), access your IP Camera on your local network
by opening Internet Explorer and specifying the IP address
and Web Port assigned to the IP Camera.

1.

2.

3.

4.

5.

Access your IP Camera via the Internet :6.

Examples: http://192.168.0.200:8888 or http://24.106.88.123

If you left your Web Port set to 80, do not need to specify the
port in the Address Bar to access the IP Camera.

If you use Case B, C

1) Open Internet Explorer.

2) Type the IP of the IP Camera.

If you use Case A, D

1) Open Internet Explorer.

2) Visit the DDNS website.

3) Register the IP Camera.

4) Give the DDNS server 10 minutes (MAX) to locate your IP
Camera’s IP information. You may reboot the server to send an
immediate request to our DDNS server.

5) After your camera is connected, select your camera.

The di ence between B and C is that B needs to set the port
forwarding.

Since the type of DDNS s from the service type, refer to
the related service site.

22

Basic Screen

Web Viewer Screen -

Web viewer is optimized with explorer10 or above version
and Firefox.

Live video display. This is the region for live video stream
from the camera.

Setup popup button. Click it to open the Setup page to
setup details of IP camera like Video, Network, Events,
System and etc. See the section ‘Setup’ .

3

When the image goes unsmoothly because of bad network
connection, it stored image during setup time and shows
the image on the live view screen.

User will see the delayed images as much as setup time.

2

1

4

Channel Select button. Select a stream produced from the
camera between Stream 1 ~ 3 to display it in the live view
screen.

Refer the ‘Setup > Video & Audio > Video’ to setup the Video
Stream.

Event Alert Icon ( ) appears if ‘Motion Detection’ is activated.

Below “Menu”is supported in accordance with models.

PTZ Control

Does not support.

Preset

Does not support.

Alarm Input

Does not support.

Motion

It shows the Motion event status.

6

Camera Time

Display the camera time.

7

5

Speaker Control

Does not support.

Relay Out

Does not support.

If VLC is not installed or VLC plugin is not supported (Chrome),

to Live Viewer menu, and then if HTML5(MJPEG) is selected on
Live Viewer menu, then you can check the video.

3

2

4

5

6

7

1

2

Video Configuration

Setup - Video & Audio Setup

2

Detail Page

When you selects an item from the menu, you can set the
details for the selected item.

1

Setup Constitution
Video&Audio

[ VIDEO, OSD, ROI, AUDIO, PRIVACY MASK ]

Camera

Network

[ STATUS, NETWORK SETTING, AUTO IP, ONVIF, UPNP,
DDNS, FTP, SMTP, SNMP, RTSP INFORMATION ]

System

[ INFORMATION, FIRMWARE UPDATE, DATE&TIME , DST ,
USER MANAGEMENT, LOG, FACTORY RESET, RESTART ]

[ IMAGE ADJUSTMENT, EXPOSURE, DAY&NIGHT,
BACKLIGHT, WHITE BALANCE, IMAGE, VIDEO ]

Events

[ EVENT RULES, MOTION, TEMPERATURE ]

Security

[ IP ADDRESS FILTER, RTSP AUTHENTICATION, IEEE 802.1x,
HTTPS, CERTIFICATES,SERVICE ]

Trigger Action

[ ACTION RULES, IMAGE TRANSFER ]

1

2

24

Video Configuration

Setup - Video & Audio Setup

1

2

3

5

4

1

2

Live Video Channel Setup

combination of codec and resolution.
The camera performance has to be considered when setting

camera.

Codec

Choose the video codec. According to the selected codec,
the subcategories can be changed automatically.
When MJPEG codec is selected, it will be able to set whether
to use the relevant channel for image transfer.

3

Description

Input the additional description about the selected channel.
Max. 30 alphabets are allowed(Including space). For the
description, English Alphabets, numbers and special
characters ( - _ @ . ) can be used.

4

Resolution

Select the video resolution.

Available resolution can be depends on the codec setup between
the channels.

<Resolution of Video Format>

720p/i

SVGA

VGA

4CIF

PAL

1280 x 720

NTSC

1280 x 720

1080p/i 1920 x 10801920 x 1080

800 x 600

640 x 480

704 x 576
704 x 480

352 x 288
352 x 240

800 x 600

640 x 480

704 x 576
704 x 480

352 x 288
352 x 240

5

Frame Rate

Select the maximum Frame Rate.

were set up.

CIF

2

Video Configuration

Setup - Video & Audio Setup

6

7

GOP(Group of Pictures) Size

Set up the number of frames (P-frame) which contain only
changed information based on basic frame (I-frame).
Regarding videos with lots of movement, if you set GOP size

bigger, only the number of P-frames is bigger. As a result,
video resolution will be low but ‘File size’ and ‘Bit-rate can
be decreased.

GOP(Group of Pictures) Size is..

I-frame and P-frame can be created for MPEG4 and H.264 video
compression. I-frame(=key-frame) means the whole image data

been changed information compared to I-frame GOP is made up
of one I-frame and corresponding several P-frames. To improve
video quality, set the number of P-frames smaller and to decrease
image size, set the number of P-frames bigger.

H.264 stream, including color reproduction and additional
video compression.

Baseline

Main

High

8

Smart Bitrate Control

CVBR (Framerate priority)

You can not use the Smart Bitrate Control function.

This Mode is for cameras which do not want absolute any
frame drop, but still want to get lower bitrate. It has
limitation when the Target bitrate is set to be very low,
but actual motion is big or scene is very noisy.

CVBR (Quality priority)

When the Target bitrate is set to very low, and motion is big,

be lower, so that it can save its and make the output frames
to have better quality.

CBR

This Mode is a CBR alike mode which is close to traditional
security IPCAM, and it's not designed for LBR, It's provided
as an option in LBR library just to help comparison.

6

8

7

2

Video Configuration

Setup - Video & Audio Setup

12

Quality

For VBR control mode, The Target Quality of video can be
setup.

9

Bitrate Mode

Select the bit rate control scheme of video compression
from CBR (Constant Bit Rate) or VBR (Variable Bit Rate).

10

Target Bitrate

If Bitrate Control is set to be CBR, you can set the Target
Bitrate.

CBR

To guarantee the designated constant bit rate, the quality
of video are controlled in this mode. Therefore, the quality

changing.

VBR

To guarantee the designated quality, the bit rate of video
stream is changed in this mode. Therefore, the frame rate

changing.

13

Click ‘Apply’ to make above setting eective.

11

Extension Option

You can not use the Extension Option.

SVC-T On

The H.264 SVC (Scalable Video Coding) is a video compre

This category won't be appear if you select the codec.

11

12

13

10

9

2

OSD Configuration

Setup - Video & Audio Setup

Date / Time

Display the current time.

User Text

Output the TEXT entered by the user.
Support a maximum of 30 characters.

Click ‘Apply’ to make above setting eective.

1

2

3

2

1

3

2

Region of Interest Configuration

Setup - Video & Audio Setup

4

Click 'Cancel' to return to the previous setting.

Click ‘Save’ to save the current settings.

Stream

Select the Stream.

1

4

Activation

The Region of interest can be enable or disable.

2

Quality

Set the quality of the set area.

3

Currently it supports only Channel1.

Region of interest function gives much more eciency picture
quality for indicated area to improve picture qualities of
movement scene at the same bandwidth.

2

1

3

4

2

Audio Configuration

Setup - Video & Audio Setup

1

Codec

Select the Audio Codec.

Currently it supports only codec G.711.

Currently it supports only 8000 Hz.

2

3

Volume

Select the Audio Volume from 0 to 10.

Sample Rate

Select the Audio Sample Rate.

4

Click ‘Apply’ to make above setting eective.

1

2

3

4



Privacy Mask Configuration

Setup - Video & Audio Setup

3

Use this function to mask areas that you want to hide on
screen to protect privacy.

1

2

Activation

The Privacy mask function can be enable or disable.

Area

Select the Area1 ~ Area4 and Set the privacy area.

Click 'Cancel' to return to the previous setting.
Click ‘Clear Area' to delete the selected Area1~Area4.

3

Click ‘Save’ to save the current settings.

1

2

3



Camera Image Adjustment

Setup - Camera Setup

6

Sharpness

Using this control, sharpness of image can be adjusted
to meet your preference.

1

2

Brightness

Using this control, brightness of image can be adjusted
to meet your preference.

3

Contrast

Using this control, contrast of image can be adjusted to
meet your preference.

Saturation

Using this control, Saturation of image can be adjusted
to meet your preference.

4

5

Hue

Using this control, Hue of image can be adjusted
to meet your preference.

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

6

Click ‘Save’ to save the current settings.

2

1

4

3

5

6

2

Camera Exposure Settings

Setup - Camera Setup

7

1

2

Auto Exposure

Automatic exposure(AE) automatically sets the aperture or
shutter speed, based on the external lighting conditions
for the photo.

Exposure Level

If this value is increases, the image becomes brighter.

3

AE metering

AE metering mode refers to the way in which a camera
determines the exposure.

6

Gain Limit

The smaller number makes the daker image.

5

Slow Shutter

Slow shutter Level lets you adjust the amount of light striking
the sensor, and essentially determines when the video sensor
sends out its batch of data for processing.

4

Shutter Speed

If this speed is faster, the moving object can be photographed
without the ghost eect. However, picture can be dark if
there is no sucient lighting.

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

7

Click ‘Save’ to save the current settings.

1

2

7

3

4

5

6



Camera Day & Night Settings

Setup - Camera Setup

2

1

4

3

5

6

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

Day & Night
Auto:

In this mode, the IR cut lter is removed automatically

depending on the light condition around.

Day:

In this mode, the IR cut lter is applied to the image
sensor all the time. Thus, the sensitivity will be reduced in
the dark light condition but the better color reproduction
performance are obtained.

Night:

In this mode, the IR cut lter on the image sensor
is removed all the time. The sensitivity will be enhanced
in the dark light condition but the image is black and white.

Schedule:

In this mode, Day / Night mode is converted

accordance with the scheduled time.

1

2

3

Color Level

It is a level to change Night mode into Day mode when
Day & Night mode is Auto.

B / W Level

It is a level to change Day mode into Night mode when
Day & Night mode is Auto.

Transition Time

If it is set to Auto, to determine the rate at which
Day / Night is converted.

4

If it is set to schedule mode, Set the time that
Day / Night is converted.

5

6

Click ‘Save’ to save the current settings.

2

1

4

3

5

6

4

Camera Backlight Settings

Setup - Camera Setup

2

1

2

WDR (Wide Dynamic Range)

The WDR function can be enable or disable.

WDR Level

Select the WDR level depending on the dierence in brightness
between the darkest and lightest part of an image.

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

3

Click ‘Save’ to save the current settings.

This is a feature used for problematic light conditions where
the contrast from light to dark areas is very high.

1

2

3



Camera White Balance

Setup - Camera Setup

2

1

3

4

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

4

Click ‘Save’ to save the current settings.

Activation

1

2

White Balance Mode

Select White Balance depending on the lighting conditions.

RGB Gain

The R/G/B gain can be set only when the White Balance
Mode is set to Manual.

3

White Balance can be enable or disable.

2

1

3

4



Camera Image Enhancement

Setup - Camera Setup

4

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

4

Click ‘Save’ to save the current settings.

3D Noise Reduction

3DNR function enables to suppress noise and retain
good video quality in low light conditions.

1

2

Mirror

Reverse the video from side to side.

Flip

Reverse the video from up to down.

3

2

1

3

4



Video Enhancement

Setup - Camera Setup

2

Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.

Click ‘Save’ to save the current settings.

Flickerless

1

2

1

2



Network Status

Setup - Network Setup

This menu will show you all the information of Network setting in the camera. However, you cannot change those here.



Network Settings

Setup - Network Setup

1

Network Type

Subnet Mask, Gateway, DNS Server and all ports.
If you select the Dynamic Mode, the IP address will be
allocated automatically by DHCP equipment. If you click
the Apply button to update changes, the system will be
re-booted. In this case, you have to reconnect the camera
using new IP address.

2

IP Address

numbers separated by dots and the range of each number
is from 0 to 255.

3

Subnet Mask

4

Default Gateway

Default the Gateway IP Address. Format is same as the IP
address.

5

Preferred DNS Server

IP address.

6

Alternate DNS Server

same as the IP address.

7

HTTP Port

The HTTP port can be set to 80 which default or in between
1025 to 60000.

8

RTSP Port

The RTSP port can be set to 554 which default or in between
1025 to 60000.

If the network type is dynamic, the IP address is changed in
below cases. Therefore, the IP address needs to be searched
again, and the camera needs to be reconnected in these
cases.

- When the camera power is

- After Firmware update, Default set and reboot.

10

9

HTTPS Port

The HTTPS port can be set to 443 which default or in betwe

-en1025 to 60000.

7

8

9

10

1

3

2

5

4

6

7

8

9

10

4

Auto IP Settings

Setup - Network Setup

3

Click ‘Apply’ to make above setting eective.

General Setting

1

Auto IP Settings Information

2

3

It displays the Unique id or Auto IP address.

1

2

3

Auto IP Settings

4

ONVIF Settings

Setup - Network Setup

1

2

3

1

Authentication
None: Allows to access without ONVIF authentication.
WS - Username token: Allows to access with WS-User

Token of ONVIF authentication.
WS + Digest: Allows to access with WS-User Token and
Digest of ONVIF authentication.

2

Discovery Mode

The discorvery function can be enable or disable.

3

Click ‘Apply’ to make above setting eective.

1

2

3

42

UPNP Settings

Setup - Network Setup

3

1

General Setting

2

Friendly Name

Dene the friendly name.

3

Click ‘Apply’ to make above setting eective.

1

2

3

4

DDNS Settings

Setup - Network Setup

3

DDNS Disable

If it is selected, DDNS service does not work.

Public DDNS

To use public DDNS service, select a site address listed in the

completed by entering User Name and Password registered
in that DDNS site.

1

2

DDNS Provider Site Address

DynDNS

No-IP

www.dyndns.com

www.no-ip.com

If you setup DDNS properly, the IP address of your camera will be
updated automatically whenever IP address is changed or system
is rebooted.

If IP updating to DDNS site is failed, camera will keep retrying in
1min. interval.

3

1

2

3

44

FTP Settings

Setup - Network Setup

1

2

4

6

3

5

7

FTP Server Address

a Message box will be shown to try again.

FTP Upload Path

English Alphabets, numbers and special characters ( / ~ !@ $
^ ( ) _ - { } [ ] ; , ) can be used.

2

General Setting

1

3

FTP Port

impossible to access to FTP Server.

4

To transfer / save the image to the relevant sites through FTP,
then FTP needs to be setup.

User ID

correct

User ID registered in the FTP Server.

5

Password

correct Password registered in the FTP Server.

6

7

Refer the above screen image for the example.

1

2

4

6

3

5

7

4

SMTP Settings

Setup - Network Setup

1

2

4

6

10

3

5

7

9

11

Mode

Select Security mode of SMTP from Plain or SSL / TLS. After
checking account setup of your SMTP Server, you may
select one.

SMTP Server Address

incorrect, a Message box will be shown to try again.

2

General Setting

SMTP function can be enable or disable.

1

3

Port

SSL / TLS security mode

in the above.

4

To send / save the image to the relevant sites by Email, SMTP
needs to be setup.

User ID

correct User ID registered in the SMTP Server.

5

Password

correct Password registered in the SMTP Server.

6

11

E-Mail Sender

displayed as the sender when the camera sends an E-mail.

7

E-Mail Receiver

displayed as the Receiver when the camera sends an E-mail.

8

Message

The message of the Email is limited to 40 characters including
the spaces.

10

Title

E-mail.

9

The title of the Email is limited to 40 characters including
the spaces.

1

2

4

6

8

10

3

5

7

9

11

4

SNMP Settings

Setup - Network Setup

SNMPv1/SNMPv2

Select the SNMPv1/SNMPv2 option and type the names of
Read community and Write community.

SNMP trap can be enable or disable.

SNMP Trap

1

2

SNMP trap can be used to check periodically for operational
thresholds or failures that are dened in the MIB.

Select the either Read or Read/Write mode.

Mode

3

It can be enable or disable selected mode.

Activation

4

Dene Read name and Write name.

Read/Write name

5

Select one of no auth, no priv/auth , no priv/auth, priv

Security Level

6

Select MD5 or SHA as the authentication method.

Authentication Algorithm

7

The Authentication Password is an encryption for
authentication and they are at least 8 digits and up
to 30 digits allowed.

Authentication Password

8

Select DES or AES as the encryption algorithm.

Private-Key Algorithm

9

Information protection password is a private encryp

-tion and they are at least 8 digits and up to 30 digits
allowed.

Private-Key Password

10

Click ‘Apply’ to make above setting eective.

11

SNMPv3 contains cryptographic security, a higher security
level, which allows you to set the Authentication password
and the Encryption password.

1

2

3

4

5

6

7

8
9

10

11

4

RTSP Information

Setup - Network Setup

Time out

Set the RTSP time out.

RTP Multicast

Check RTP Multicast On/O. To activate RTP Multicast,

1. Click “On” button

2. Enter accessible RTP Multicast IP, port for video stream

control, RTP packet TTL

3. Click “Apply” button.

2

Target Stream

Select the channel you want to set.

1

3

Click ‘Apply’ to make above setting eective.

4

It shows RTSP Connection information.

5

The session is disconnected after the specied time out.

It is possible to set each RTP Multicast for CH1~3.

Click this button when completed setup each channels.

1

2

4

3

5

4

Action Rules Configuration

Setup - Trigger Action Setup

1

2

Action rules List

It indicates the custom action rule information added to
Action rules list.

1

Click ‘Modify' to modify selected item from the action rules list.
Click 'Delete' to delete selected item from the action rules list.

2

Click ‘Add’ to add custom action rules.

1

2

4

Action Rules Add / Modify

Setup - Trigger Action Setup

Name

Dene name of action rules.

1

Click 'Cancel' to return to the previous menu.

4

Click ‘Save’ to save the current settings.

2

Action1 ~ Aciton5

Select the action to take If the event occurs.

3

3

1

2



Image Transfer Configuration

Setup - Trigger Action Setup

Number

of Image

Pre-alarm

Duration

Post-alarm

Duration

Descriptions

Dene duration of image transfer before an event.

Dene duration of image transfer after an event.

2

Pre / Post Alarm Image

Image Transfer due to event is congured by setting Image
transfer rate and Pre / Post alarm duration.

1

2

1

2



Event Rules Configuration

Setup - Events Setup

1

Event Rules List

It indicates the custom Event Rule information added to
Event Rules list.

Click ‘Modify' to modify selected item from the event rules list.
Click 'Delete' to delete selected item from the event rules list.

2

Click ‘Add’ to add custom event rules.

1

2

2

Event Rules Configuration

Setup - Events Setup

1

Name

Dene the Event rule name.

2

Event

Select the event among motion detection, schedule.

3

Rules

Select the action rule dened in the Trigger Action-Action
rule menu.

Click 'Cancel' to return to the previous setting.

Click 'Cancel' to return to the previous setting.
You need a event one more.

4

Click ‘Save’ to save the current settings.

2

1

4

3



Motion Detection Configuration

Setup - Events Setup

Area

Set the motion detected area.

2

Motion Detection

It shows the Motion event status.

3

Sensitivity

High value is
selected, it will detect very small motion while it becomes
relatively insensitive when Low value is selected.

4

1

Event Alert Icon( ) appears if ‘Motion Detection’ is activated.

You can set up to four areas.

5

Click ‘Save’ to save the current settings.

Click 'Cancel' to return to the previous setting.

Activation

Enable or Disable motion detection function.

1

2

3

4

5

4

Temperature

Setup - Events Setup

1

2

3

4

Mode

Select the either Fahrenheit and Celsius.

Click ‘Apply’ to make above setting eective.

1

Temperature

It indicates the current temperature of the IP camera.

3

Threshold

Dene the temperature at which the event trigger is
occurred.

2

4



IP Address Filter Configuration

Setup - Security Setup

1

IP Address Filter

IP lter function can be enable or disable.

4

Filter IP Address

Display the lterd IP address.

IP Filter Type

Select the recording IP lter type.

2

Click ‘Add’ to add the ip address to the list.

6

5

IP Address

Dene the IP address you want to apply the IP lter.

Click ‘Remove’ to remove the ip address selected in the list.
Click ‘Remove All’ to remove all ip in the list.

3

3

2

1

5

4

6



RTSP Authentication Configuration

Setup - Security Setup

1

RTSP Authentication

RTSP Authentication can be enable or disable.

Click ‘Apply’ to make above setting effective.

2

2

1



IEEE 802.1X Configuration

Setup - Security Setup

The featureis needed when connecting the camera to the
network protected bythe IEEE 802.1X.

1

IEEE 802.1x

The IEEE 802.1x feature can be enable or disable.

4

EAPOL Version

Select the EAPOL Version.

Protocol

MD5: It provides one-way password-based network
authentication of the client.
PEAP: It is similar to TTLS in that it does not require a certifi

-cate on the client side.
TTLS/MD5: It does not require a certificate on the client side.
TLS: It relies on client-side and server-side certificates to
perform authentication.

2

6

5

Password

Type the Password to identify the client in the IEEE 802.1X
authentication server.

Verify

Verify Password.

ID

Type the ID to identify the client in the IEEE 802.1X authen

-tication server.

3

7

CA Certificate

Select the CA certificate required for TLS, TTLS, and
PEAP authentication.

Click ‘Apply’ to make above setting effective.

Certificate

Select the client certificate required for TLS authen

-tication

8

9

3

2

1

4

5

6

7

8

9



HTTPS Configuration

Setup - Security Setup

HTTPS encrypts session data over SSL or TLS protocols
instead of using plain text in socket communications.

1

Certificate

Select an installed certificate.

Click ‘Apply’ to make above setting effective.

HTTPS connection Policy

Select one of “HTTP”, “HTTPS”, “HTTP and HTTPS”
depending on the connected user authority.

2

3

If you can not select a certicate, please install the certicate
from the Security->Certicates menu.

When HTTPS mode is chosen, input https://<IP Address> to
connect to the camera.

3

2

1



Certificates Configuration

Setup - Security Setup

1

Server/Client Certificates

It show the installed certificates.

Properties

Shows information about the selected certificate.

Create Self-Signed Certificate

A self-signed SSL certificate is an identity certificate signed
by its own creator. but they are considered to be less trust

-worthy.

2

3

8

Install CA Certificate

Install Certification, see the detail page.

Delete

Delete the selected CA certificate.

Properties

Shows information about the selected certificate.

9

10

Delete

Delete the selected certificate.

4

Create Certificate signing request

This is the encoded data that contains the necessary infor

-mation for issuing the certificate.

5

they must be lled in when creating the CSR (Certicate Signing
Request).

Install Certificate

Install Certification

6

CA Certificate

It show the installed CA certificates.

7

3

4

7

9

10

2

5

8

1

6



Certificates Configuration

Setup - Security Setup

2

3

4

6

10

5

9

1

7

8

1

Certificate From Signing Request

Select to install signed certificate returned from the CA.

Detail for Install Certification.

Certificate Name

Enter a unique name to identify certificate.

Certificate And Private Key

Select to install Certificate And Private Key to install a certi

-ficate and private key.
Use Seperate Key: Too install certificate uploading Certifi

-cate and Private Key file.

PKCS#12” : “PKCS#12” is cryptography standard.

if you want to install using PKCS#12,
must enter the password.

2

3

Select File

Choose certification file.

4

OK

Request installing certificate.

5

Cancel

Cancel install certificate and then back to certificates
configuration.

6

Detail for Install CA Certification.

9

OK

Request installing CA certificate.

Cancel

Cancel install CA certificate and then back to certi

-ficates configuration.

10

Certificate Name

Enter a unique name to identify CA certificate.

7

Select File

Choose CA certification file

8



Service Configuration

Setup - Security Setup

1

Telnet

The Telnet function can be enable or disable.

Click ‘Apply’ to make above setting eective.

2

1

2

2

System Information

Setup - System Setup

1

Device Name

You can dene the device name.

System Capability information.

6

1

2



Firmware Update

Setup - System Setup

Version Information

It shows the current Firmware Version in the system.

Web Update

1

2

Start F / W Update

Click this button to start update. Progress of uploading will
be displayed using Progress Bar. If you assign the wr

e

name, an error massage will be shown.

3

Warning:

1. Do not turn the power of camera during the Firmware
update. Otherwise, the system can be stuck to be unstable.

automatically.

2. Please make sure to check the ‘Notice’ shown on screen.
If

mware update is completed, the camera will reboot

automatically and ‘Setup window’ will be closed.

1

2

3

4

Firmware Update

Setup - System Setup

4

5

FTP Server Address

Dene FTP Server IP Address. If IP Address form is incorrect,
a Message box will be shown to try again.

FTP Upload Path

Dene a path in FTP server to store video. For the path name,
English Alphabets, numbers and special characters
( / ~ ! @ $ ^ ( ) _ - { } [ ] ; , ) can be used.

4

5

7

8

9

FTP Port

Dene the FTP Server Port. If Port is not appropriate, it is
impossible to access to FTP Server.

User ID

Dene User ID to access to the FTP Server. Fill out the correct
User ID registered in the FTP Server.

Password

Dene Password to access to the FTP Server. Fill out the
correct Password registered in the FTP Server.

Click ‘Save’ to make above setting eective.

6

CHECK

CANCEL Click 'Cancel' to return to the previous setting.

SAVE Save FTP information

Check the F/W le and if the le exists, ‘F/W Update’
button will appear and click it to update for F/W.

6

7

8

9



Date & Time Settings

Setup - System Setup

TimeZone Setup

Choose TimeZone for camera. It will be activated after
clicking ‘Apply’ button.

Prior to setting below ‘New Camera Date & Time’, set correct

Current Date & Time

Shows the current date and time setting in the Camera.

Synchronize with my computer

Set the date / time using those of PC currently connected.

Setup manually

Set the date / time by typing manually.

1

2

5

Synchronize with time sever Time Zone (NTP)

Choose time server available to connect to current camera.
Date & Time will be updated automatically every hour
when connected.

3

4

6

1

2

3

4

5

6



DST Settings

Setup - System Setup

General Setting

DST function can be enable or disable.

Set the Start time and end time that the DST apply.

Date&Time Settings

1

2

3

Daylight Saving Time (DST) is the practice of setting the clocks
forward one hour from standard time during the summer
months, and back again in the fall, in order to make better
use of natural daylight.

1

2

3



Users Management

Setup - System Setup

3

4

Modify

Modify the information of the user accounts registered.
For admin account, only Password function

Delete

Delete the selected user account. Admin account cannot
be deleted.

Add

Register a new user

2

User

Authority

Verify

Password

Enter the user Password.

ID Enter a new user ID except Admin since it exists.

The ID and Password are limited to 10 characters.

Click 'Cancel' to return to the previous menu.

Users

List all the user accounts for authentication.

1

Select Operator or Viewer.
Viewer : Only monitoring is allowed.
Operator : Most of the functions are allowed except ‘Setup’.
Administrator : All functions are allowed.

1

2 3 4



System Log

Setup - System Setup

Filter

1

2

System Log List

3

Click the 'Refresh' button to refresh the log list.

1

2

3



Factory Reset

Setup - System Setup

Reset to the factory defaults Return the setup to the factory
default.

1

2

All

Reset all Settings to the factory defaults.

Except Network Settings

Except Network related settings , reset all others to the
factory default.

1

2



Restart

Setup - System Setup

If you click the ‘RESTART’ menu, a message box will be shown to conrm. Click the ‘Ok’ button to restart.



A : Current TCP/IP Settings

Appendix

If your IP settings are obtained automatically, you could use the MS-DOS prompt (or Command Prompt) to determine your IP address.
For information on how to do this, please read the FAQ.

Under the ‘General’ tab of the
TCP/IP Properties you will see
your IP address information.

Start

Network and

sharing center

Manage network

connections

Properties

Select either

Internet Protocol

Ver.4 (TCP/IPv4)

or Internet Protocol

Ver.6 (TCP/IPv4)

Select either

Internet Protocol

Ver.4 (TCP/IPv4)

or Internet Protocol

Ver.6 (TCP/IPv4)

Click Properties

Control Panel

Under the ‘General’ tab of the
TCP/IP Properties you will see
your IP address information.

Start

Click on Change

adapter options in

Ethernet

Select the Ethernet,

Right click and

choose Properties

Click Properties

Settings

Network & Internet

2. Windows 10 Users1.

Windows 7 Users

72

B : Changing IP address and subnet mask

Appendix -

Select ‘Use the following IP
address’

Start

Network and

sharing center

Manage network

connections

Properties

Select either

Internet Protocol

Ver.4 (TCP/IPv4)

or Internet Protocol

Ver.6 (TCP/IPv4)

Select either

Internet Protocol

Ver.4 (TCP/IPv4)

or Internet Protocol

Ver.6 (TCP/IPv4)

Click Properties

Control Panel

Select ‘Use the following IP
address’

Start

Click on Change

adapter options in

Ethernet

Select the Ethernet,

Right click and

choose Properties

Click Properties

Settings

Network & Internet

2. Windows 10 Users1.

Windows 7 Users

73

Spec.

SPECIFICATION

CAMERA

Image Sensor

Total Pixels

Focal Length

Angle

Shutter Speed

MIN. Illumination

IR

WDR

WDR dB

Day & Night

DNR

Privacy Zone

AGC

Other Image Processing

2.1MP 1/2.7" CMOS Sensor

1928(H) X 1088(V)

2.8mm, F2.0/4mm, F2.6

D : 136°, H : 118°, V : 65° (2.8mm)
D : 103°, H : 88°, V : 46° (4mm)

2.8mm : 0.25Lux, 0Lux with IR(F2.0)
4mm : 0.39Lux, 0Lux with IR(F2.6)

H2IR, 50ft

WDR(2x)

120dB

TDN

3D-DNR

16 Programmable Zone

Auto

Balance, Sharpness

ENCODER(VIDEO&AUDIO)

Video Compression

Streaming
Performance

Video Bitrate

Bitrate Control

Edge Storage

H.264, MJPEG

BP/MP/HP

1080p30 + 480p30 with H.264 +
MJPEG

100kbps~10Mbps,

Multi-rate for

Pre

view and Recording

Multi Streaming CBR/VBR at H.264
(Controllable frame rate and Band
width)

N/A

GENERAL

Support Languages

Power

Temperature

Material

Dimensions(DXH)

Weight

English

PoE IEEE 802.3af Class2: 5.2W

-4°F~122°F (-20°C~50°C)

Aluminum Die-casting

4.13 x 2.38 in (105 x 60.7mm)

0.95lbs (350g)

FCC, CE, ROHS, IP64, IK10

I/O & EVENT

Audio In/Out

Alarm In/Out

Video Output
(2nd Video Out)

MIC Input

N/A

1[CVBS 1.0V p-p(75Ω)],
4:3 aspect ratio

FTP, E-mail

SECURITY & NETWORK

Network Protocol

Security

Plug in

IPv4
ONVIF, TCP/IP, UDP, RTP(UDP/TCP),
RTSP, NTP, HTTP,HTTPS, SSL,
DNS, DDNS, DHCP, FTP, SMTP, ICMP,
SNMPv1/v2c/v3(MIB-2)

Digest Authentication(ID/PW)

CGI API, ONVIF

74

Auto / Manual (1/15 ~ 1/32000),
Anti-Flicker, Slow Shutter
(1/2,1/3,1/5,1/6,1/7.5,1/10)

FAQ

My POWER light is not on?

Power is not being supplied to the unit. Please use the power
supply shipped with the unit and verify that a power source
is active from the attached power outlet used to connect the
adapter. You can test this by plugging in any other electrical
device and verify its operation. After using the power supply
shipped with the product, checking the power source, and
reinserting the power connector into the IP Camera, please
call our Support Center. The power supply may be defective.

Verify the power supply to the unit. Pow unit and
back on again, wait 1 minute, if the ACTIVE light still does
not begin t

ash, you will have to set the unit to its factory
default (THIS WILL DELETE ANY CONFIGURATION AND SET
THE UNIT TO THE FACTORY DEFAULTS). Power on the unit
and insert the end of a paper clip into the small recessed
opening on the back of the unit. Use the clip to press the
button located within that opening.

Verify the cable connection. 99% of the time the cable’s
connection to the unit is causing this problem. Try using a
di

t network cable or crossover cable (for PC connection
only). Try reinserting the cable, if this still doesn’t solve the
problem call our Support Center.

I can access the video server on my LAN, but not from the
Internet.

Verify that your router (if applicable) has port forwarding

ccessing from our DDNS service,
verify correct serial number. Firewall issues may prevent user
access.

How do I open an MS-DOS or Command Prompt?

1.

2.

3.

4.

5.

Appendix -

Start > (All) Programs > Accessories > Command Prompt

How d

d out my IP address information if my settings

were automatically detected?

6.

1) Open a Command Prompt

3) Near the end of the information supplied, should be your
current IP address, subnet mask, default gateway and DNS
servers

How do I “PING” an IP address?

1) Open an MS-DOS (or Command) prompt

2) At the prompt type - “ping xxx.xxx.xxx.xxx” (without the
quotes and replace the “x”s with an IP address)

3) Press Enter

I’m accessing my video server remotely over the Internet
and the video stream is choppy, is this normal?

Yes. The frames per second received remotely are
determined by your bandwidth capabilities both at your site
where the IP Camera is installed and your remote location.
The lower of the two sites will determine how fast your
video stream is received. It is recommended to have at least
a 256Kb/sec upstream connection from the site where the
IP Camera is installed. Lower speeds will operate properly,
but provide poor remote performance. The Faster the
Internet connection at both ends, the faster the video
stream.

How do I enable or check VLC on my browser

Open Internet Explorer > Tools on the menu bar > Internet
Options > Security Tab > Custom Level > Scroll down and
verify that you are prompted or have enabled plug-ins to be
downloaded and executed. > click OK > restart browser.

How do I reset the unit to factory defaults?

Refer to the previous functions page and nd the reset button.
Power ON the unit and use a paper clip to push the reset button
within that opening. You should then see the ACTIVE light turn
o and after a few seconds the ACTIVE light will begin to ash,
signifying a successful reboot. If the ACTIVE light does not turn
o after depressing the reset button, please try holding the
button in for a few seconds and releasing. YOU WILL LOSE ALL
DATA THAT HAD BEEN ENTERED PREVIOUSLY AND THE IP CAM

-ERA WILL BE SET TO ITS FACTORY RESETS.

8.

9.

10.

11.

Internet Explorer

Open Chrome > Chrome menu settings > Advanced settings >
Individual information - content settings > Run automatically

Chrome

I can’t connect!!

In the case of a connection failure.
Modem Reboot > Modem Reboot Finished > Router Reboot
> Router Reboot Finished > IP Camera Reboot > IP Camera
Reboot Finish > Verify DDNS and IP Camera connection, if
applicable.

7.

75

Warranty Information

%JHJUBM8BUDIEPH(referred to as “the Warrantor”) warrants the Camera against defects in materials or
workmanships as follows:

Labor: For the initial five (5) years from the date of original purchase if the camera is determined to be
defective, the Warrantor will repair or replace the unit with new or refurbished product at its option, at no
charge.

Parts: In addition, the Warrantor will supply replacement parts for the initial five (5) years.

To obtain warranty or out of warranty service, please contact a technical support representative at
1+ [phone], Monday through Friday from 9:00AM to 8:00PM EST.

A purchase receipt or other proof of the date of the original purchase is required before warranty service
is rendered. This warranty only covers failures due to defects in materials and workmanship which arise
during normal use. This warranty does not cover damages which occurs in shipment or failures which are
caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse,
neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments,
improper antenna, inadequate signal pickup, maladjustments of consumer controls, improper operation,
power line surge, improper voltage supply, lightning damage, rental use of the product or service by
anyone other than an authorized repair facility or damage that is attributable to acts of God.



Limits  Eclusions

There are no epress warranties ecept as listed above. The Warrantor will not be liable for incidental or
consequential damages (including, without limitation, damage to recording media) resulting from the
use of these products, or arising out of any breach of the warranty. All epress and implied warranties,
including the warranties of merchantability and fitness for particular purpose, are limited to the
applicable warranty period set forth above.

Some states do not allow the eclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above eclusions or limitations may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights from vary from state
to state.

If the problem is not handled to your satisfaction, then write to the following address:

igital Watchdog, Inc.
ATT: MA epartment
5436 W Crenshaw St
Tampa, FL 33634

Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in
its sole discretion, are not covered. Cost of such service calls are the responsibility of the purchaser.



ast Coast eadquarters ffice: 5 W Crenshaw St, Tampa, F 

West Coast eadquarters ffice:  loomfield Ae., Cerritos, CA 

P: --55 FA: --

www.Digital-Watchdog.com Technical Support:

SA  Canada   -55

International   -555

French Canadian  5 -

Support ours: onday-Friday :am to :pm ST