Digital Watchdog DW-DTMWIPW, DW-DTPIRIPW Quick Start Guide

Quick Start Guide Quick Start Guide

MOTION DETECTORS

DW-DTPIRIPW DW-DTMWIPW

WHAT’S IN THE BOX

1 x detector

1 x mounting temp late

3 x 1.25” (31 .75mm) wall anch ors and washers

2 x spare sliding c urtains

1 x tamper feet 0.039” ( 1mm) long

1 x tamper feet 0.078” (2m m) long.

STEP 1 – Mounting the Motion Detector

1. Find the suitable location to install the SiteWatch™. The
sensor should be position so the person will pass across
the field of view and not directly toward or away
from it.

2. Using the mounting template sheet or the detector
itself, mark and drill the necessary holes in the wall. It

is recommended to use the tamper cup on uneven wall
surfaces. Refer to Fig. 1.

Suggested mounting hight of 10ft is recommended.

Fig. 1

2. Remove the cover assembly by loosening the locking
screw. The cover hinges from the top and lifts out of the

location slot. Refer to Fig. 2.

STEP 2 – CABLING THE DETECTOR

1. Pass the CAT5e/CAT6 cable through the cable entry
from outside to inside.

2. Install the Cat5e / Cat6 through the provided hole on
the rear of the detector. Terminate the Cat5e / Cat6
cable using an RJ46 connector leaving enough cable to
connect to the RJ45 port. Refer to Fig. 3.

3. Plug the connector into the RJ45 port. Refer to Fig. 4.

* Tools are required to crimp RJ45 connector. RJ45
Connector not included.

Use the diagram below to connect your detector to the
necessary external devices.

Power input Power consumption

Power over Ethernet (48V DC) Max 3 .8W, PoE class 1

1 x quick setup gui de

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources.

2. Se arch for your product by entering the part
number in the ‘Search by Product’ search bar.
Results for applicable part numbers will
populate automatically based on the part
number you enter.

3. Click ‘Search’. All supported materials, including
manuals and quick start guide (QSGs) will
appear in the results.

Attention: This document is intended to serve as a quick reference
for initial setup. It is recommended that the user read the entire
instruction manual for complete and proper installation and usage.

Tel: [phone]

Technical Support Hours:
9:00AM – 8:00 PM EST, Monday thru Friday

digital-watchdog.com

Locking
screw

Fig. 2

NOTE: The maximum mounting height is 10ft when

utilizing the creep detection zone.

Fig. 3

Program

RJ45

Reset

Fig. 4

Quick Start Guide

STEP 3 – INSTALLING THE DETECTOR

1. Nylon washers provided must be used with screws.

2. Ensure cable entry and screw holes are sealed with
water-based sealant.

*NOTE: Do not use silicone-based sealant.

Tamper Cup

3. Screw the unit to the wall ensuring that the rear tamper
pin is correctly located and that the tamper micro

switch is closed.

4. To aid installation, two spare tamper feet are provided.
One is 0.04” (1mm) longer and the other is 0.08” (2mm)
longer than the tamper foot originally fitted. The tamper
foot is a push fit and can be removed by carefully

pulling it from the pin.

5. When the detector is aligned, connected, and
programmed to suit the installation, close the front
cover and lock as shown.

STEP 4 – PROGRAMMING THE DETECTOR

The DW-DTPIRIPW and DW-DTMWIPW can be setup remotely via the detector’s web interface.
To open the detector’s web interface:

1. Open a web browser.

2. Enter the detector’s default IP address in the in the address bar.
The detector’s default IP address is 192.168.0.10.

3. If this is the first time you are accessing your detector’s web interface, you will be prompted to setup the username
and password. Follow the guidelines at the bottom of the page to create an adequate password.

NOTE: Default IP address: 192.168.1.10

*

NOTE: Please see the full product manual for web

viewer setup, functions and camera

settings options.

Factory resetting the detector:

1. Make sure the detector is powered on.

2. Hold down the reset button for 8 seconds.

3. Release reset button, the status LED on the board
will turn o for a second.

4. The units IP address and login details are now
reset back to factory values.

Rev Date: 0 9/19

Speci ficati ons and p ricing are subj ect to ch ange without notice.

Copyright © Digital Watchdog. Al l rights reser ved.