Digital Watchdog DWC-V7553WTIR Quick Start Guide

Quick Start Guide Quick Start Guide

Screw &

Plasc Anchor-2pcs

Torx Wrench

Screw &

Plasc Anchor-2pcs

Screw &

Mount b olts
and nuts

DWC-V7553WTIR

WHAT’S IN THE BOX

Tem p la te
sheet

1 Set

for bolt
and nut
installation

1 Set

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the weight of
your camera.

2. Do not let the cables get caught in improper places or the electric
line cover can be damaged. This may cause a short or fire.

3. Detach the camera’s dome cover by loosening the 2 screws on the
dome using the included torque wrench.

4. Use the mounting template to mark and drill the necessary holes in
the mounting surface.

Protection sticker

STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES

Pass the wires through the mount bracket and make all

necessary connections. Connect the BNC cable and power
cables to the camera.

Power

Requirements

DC12V

Power Consumption

DC12V (LED o ): 2W, 176mA

DC12V (LED on): 2.69W, 224mA

Torque
wrench

Screw an d
plastic
anchor-2pcs

NOTE: Download all your suppor t materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by ente ring th e part number in
the ‘Searc h by Prod uct ’ sea rch bar. Result s for
applicable part numbers will populate automatically
based on the part number you e nter.

3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results .

Attention: This document is intended to serve as a quick reference for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.

Tel: [phone]

Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday

1 Set

1 Set

Quick S etup
Guide

Test video
cable

1 Set

1 Set

digital-watchdog.com

THE CAMERA

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:

a. Enter the camera’s OSD menu. You can access it locally from
using the camera’s joystick in the body of the camera, or from a
recorder supporting UTC communication. Go to SETUP >
OUTPUT > ANALOG MODE.

b. Set the camera’s analog signal output from the following
options:

• HD-A: supports 5MP/1944p @ 20fps and 12.5fps, 4MP/1440p
@ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.

• HD-T: supports 5MP/1944p @ 20fps, 4MP/1440p @ 30fps,

2.1MP/1080p @ 30fps and 720p @ 30fps.

• HD-C: supports 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps
and 720p @ 30fps.

• CVBS: supports up to 960H @ 30fps

STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN

1. Once all cables have been connected, use the screws included with the camera to properly mount and secure the camera to
the mounting surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired view. The cameras’ max angles are:

Pan: 0° ~ 355°

Tilt: 0° ~ 70°

Rotation: 0° ~ 360°

3. The camera has a manual IR switch, located under the camera’s lens. You can use this
switch to manually turn the IR LEDs on or o according to your installation needs.

IR Switch
ON/OFF

Quick Start Guide

Template
Sheet

c. Change CONFIRM to ON to save the changes.

d. Go to the EXIT menu and select SAVE&EXIT to save all changes.
The camera signal automatically.

4. Once the installation is complete, remove the protective film from the camera’s dome cover.

To remove it, loosen the screw on the decorative ring and rotate the ring

counter-clockwise to remove.

Panning 355°

Rotation 360°

Titling 70°

Rev Date: 0 6/1 9

Speci fications an d pricing are subjec t to change with out notice.

Copyright © Digital Watchdog. All rights reserved.