Digital Watchdog DWC-LPR650U User Manual

STAR-LIGHT Universal HD
over Coax
TM
License Plate
Recognition Bullet Camera
User’s Manual Ver. 08/17
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
Index
INTRODUCTION
02 07 08 09 10
INSTALLTION
11 12 14 15
16
OSD MENU
17 18 21 22
23 24 25 26
28
APPENDIX
28 29
31 32
Safety Information Features Part Name Dimension Product & Accessories
stallation
In
Installation - License Plate Recognition Setup
Connecting to Monitors Control Board Adjusting the Camera angle
Menu Tree OSD Menu - Exposure OSD Menu - Color OSD Menu - Day&Night OSD Menu - Function OSD Menu - Motion OSD Menu - Privacy OSD Menu - Setup OSD Menu - Exit
Troubleshooting Specifications Limits & Exclusions Warranty
2
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance
WARNING
To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.
6. Do not place conductive objects (e.g. screw drivers, coins, metal things, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
3
Safety Information
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way.
10. When cleaning, do not spray water directly onto parts of the product.
Doing so may cause fire or electric shock.
PRECAUTION
Operating
.
Before using, make sure power supply and all other parts are properly connected.
.
While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and contact your dealer.
Handling
.
Do not disassemble or tamper with parts inside the camera.
.
Do not drop the camera or subject it to shock or vibration as this can damage the camera.
.
Clean the clear Lens cover with extra care. Scratches and dust can ruin the quality of the camera image.
Installation and Storage
.
Do not install the camera in areas of extreme temperature, exceeding the allowed range.
.
Avoid installing in humid or dusty environments.
.
Avoid installing in places where radiation is present.
.
Avoid installing in places where there are strong magnetic ÿelds and electric signals.
.
Avoid installing in places where the camera would be subject to strong vibrations.
.
Never expose the camera to rain or water.
4
Important Safety Instructions
1. Read these instructions.
All these safety and operating instructions should be read before the product is installed or operated.
-
2. Keep these instructions.
The safety, operating and use instructions should be retained for future reference.
-
3. Heed all warnings.
All warnings on the product and in the operating instructions should be adhered to.
-
4. Follow all instructions.
All operating and use instructions should be followed.
-
5. Do not use this device near water.
For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; near a swimming pool; etc.
-
6. Clean only with dry cloth.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
-
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and
to protect it from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or
other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided and the manufacturer’s unstructions have been adhere to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
has two blades and a third
5
Important Safety Instructions
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, t
by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
ripod, bracket, or table specified
Disposal of Old Appliances
1. When this crossed-out product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste stream stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interferenece at his own expense.
wheel bin symbol is attached to a product it means the
6
Features
Universal HD over Coax™ Technology with HD-Analog, HD-TVI, HD-CVI and all Analog
to 960H Signal Support
2.1MP 1/3" Image Sensor at Real-time 30fps
HD Analog LPR™ License Plate Recognition Technology captures reflective license
plates up to 50mph with a 13’~30’ Capture Range
Reliable Performance under Any Lighting Conditions
External OSD and Lens Adjustment
Varifocal P-Iris Lens 6~50mm
OSD Control Via Coaxial (UTC)
115' Smart IR™ with Intelligent Camera Sync.
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
Auto Sensing 24VAC/12VDC with Line Lock
Easy Icon Driven OSD Menu with Built-in Joystick
Programmable Privacy Zones
Auto Gain Control (AGC)
Backlight Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
No Fog or Condensation Under any Weather Conditions
IP66 Certified Weather and Tampering Resistant
5 Year Warranty
7
Part name
Sunshield Cover
Lens
Zoom Control
Sunshield Adjusting Screws
Sunshield Adjusting Screws
Focus Control
OSD Joystick
Right
EX-CON
Up
Left
Down
2ND
Test Video Slot
Con Cap
BNC Cable
Mounting Bracket
Power Cable
8
Dimension
Unit : Inches (mm)
10.4" (264mm)
3.6" (92mm)
3.8" (96.7mm)
5.15" (131mm) 3.7" (94mm)
8.8" (225mm)
3.8" (96.7mm)
3.07" (78mm)
9
Product & Accessories
Please check if all the camera and accessories are included in the package.
Camera
Torx Wrench DC Plug Cable
Template Sheet
:
NOTE
The ‘Test Video Cable’ is used to test the camera by connecting to a portable display.
Manual
10
Test Video Cable
Screw &
Plastic Anchor-4pcs
Installation-
11
Instructions
1
Using the mounting template or your own camera, mark and drill the necessary holes to mount the bracket to a wall or ceiling.
2
Pull a necessary wires through and make the proper connections.
3
Use the four mounting screws to install the camera on the wall or ceiling.
:
NOTE
Electrical junction box and required screws sold separately.
Installation-
12
Instructions
An LPR camera is designed to read a license plate only. When a license plate passes by the camera, the reective lm on the plate will be reected back to the camera which gives you the good clear shot of the plate. You will ONLY capture an image of the plate. US license plates need to be at least 216 pixels wide. This translates roughly into an image no wider than 5-6 feet assuming 1080P standard denition video.
1
The horizontal angle between the camera and plate should be within 20° degrees. This means that if your camera is 10 feet away from the plate, the plate cannot be more than 3 feet to the right or left of the camera.
2
The vertical angle between the camera and plate is within 30° degrees. This means that if your camera is 10 feet away from the plate and the plate is 3 feet o the ground, the camera cannot be mounted more than 8 feet high.
3
Attempting to position the security camera at odd angles or exceeding the distance capabilities will result in a poor shot of the plate
4
The DVR’s recording fps should be at the highest to assure best capture quality.
THE CAMERA SHOULD BE MOUNTED AT AN ANGLE NO GREATER THAN 30 DEGREES
Installation-
13
Instructions
< 20°
CAMERA ANGLE NO GREATER THAN 20 DEGREES FOR SIDE MOUNT INSTALLATIONS
< 30°
THE CAMERA SHOULD BE MOUNTED AT AN ANGLE NO GREATER THAN 30 DEGREES
Connecting to DVR/Encoder
14
Use the diagram below to connect to an Universal DVR or CRT Monitor properly.
12VDC/24VAC
COAX
Test Video Output
Monitor
- Power Connection - 12VDC/24VAC Dual Voltage(Auto Polarity Detection and Protection)
- All cameras are equipped with a test video output for on-site conguration.
CCTV Monitor
Right
Up
Left
EX-CON
Down
2ND
Control Board
15
Zoom Control
Focus Control
Joystick: Controls the OSD menu.
Right
EX-CON
Up
Left
Down
2ND
- OSD Joystick : The function setting and video output can be adjusted with OSD joystick. (default : HD-A)
Image Mode
Switches to HD-TVI mode when press OSD Joystick to left 5sec or longer. Switches to HD-A mode when press OSD Joystick to right 5sec or longer. Switches to CVBS mode when press OSD Joystick to up 5sec or longer. Switches to HD-CVI mode when press OSD Joystick to down 5sec or longer.
- Zoom Control : clockwise(Tele), couter-clockwise(Wide)
- Focus Control : clockwise(Far), counter-clockwise(Near)
Test Video Connector: Video Output Connector for On-Site Conguration
Adjusting the Camera angle
16
Rotate 360˚
Tilt 90˚
Warning:
- Do not rotate more than 360
- Do not unnecessarily twist too many times.
˚
Pan 360˚
OSD Menu Tree
17
:
NOTE
The function setting can be adjusted with both switch (OSD joystick) and remote control through RS485 or UTC. In case of camera without OSD joystick, it can be adjusted with coaxial (UTC) only.
EXPOSURE
EXPO
LENS BACKLIGHT DRC DEFOG AGC 3D DNR EXIT JUMP
COLOR (not used)
RGB
EXIT JUMP
DAY & NIGHT
D&N
SMART IR EXIT JUMP
FUNCTION
FUNC
SHARPNESS GAMMA MIRROR FLIP EXIT JUMP
MOTION
MOTI
MOTION DET WINDOW DET TONE MDRECT FILL SENSITIVITY MOTION OSD TEXT ALARM SIGNAL OUT EXIT JUMP
MANUAL / AUTO OFF / HME / BLC OFF / LOW / MIDDLE / HIGH OFF / ON 0 ~ 10 OFF / LOW / MIDDLE / HIGH
0 ~ 20
0 ~ 10
0.45 ~ 0.75 OFF / ON OFF / ON
OFF / ON
0 ~ 4 OFF / ON 0 ~ 10 OFF / ON OFF / ON OFF / ON
PRIVACY
PRIV
PRIVACY ZONE NUM ZONE DISP H-POS V-POS H-SIZE V-SIZE Y LEVEL CB LEVEL CR LEVEL TRANS EXIT JUMP
SETUP
SET
COMMUNICA CAM TITLE IMAGE RANGE FREQ LANGUAGE INITIAL EXIT JUMP
EXIT
EXIT
SAVE & EXIT EXIT
This is a License Plate Recognition Camera. As such, it has been programmed speciacally to register licese plates only. For optimal results, this camera is set to B/W mode only. Thers is Color mode on this camera. As a result, some of the menu options, such as Color and Day/Night menu options, are disabled for this camera.
OFF / ON 0 ~ 15 OFF / ON 0 ~ 59 0 ~ 33 0 ~ 60 0 ~ 34 0 ~ 20 0 ~ 20 0 ~ 20 0 ~ 3
OFF / RIGHT UP / LEFT DOWN FULL / COMP / USER 50Hz / 60Hz ENG/ CHN/ CHN(S)/ JPN / KOR OFF / ON
OSD Menu_Exposure
18
LENS
1
MANUAL : Manual mode supports the xed board lens or the manual iris lens. AUTO : AUTO mode sets the camera’s iris automatically.
EXPOSURE
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
1
LENS AUTO BACKLIGHT OFF DRC OFF DEFOG OFF AGC 3 3D DNR HIGH EXIT JUMP
LENS
LEVEL ___ BRIGHTNESS 10 SHUTTER MANUAL FOCUS ADJ OFF RETURN
Under the LENS sub-menu, you can adjust the following settings:
1. Level
Change the camera’s iris value manually. If AUTO is selected, this option is disabled.
2. Brightness
Adjust the camera’s brightness from 0~20. The higher the number, the brighter the image will appear.
3. Shutter
Set the shutter speed to AUTO, Manual, or FLC (Flicker-less mode). * If AUTO is selected, select from the following options :
- NORMAL: Set when the camera is installed in an indoor environment.
- DEBLUR: Set when the camera is installed in an outdoor environment.
* Select FLC if the camera is experiencing some ickering in the image.
The shutter speed will be set to 1/100 for NTSC, or 1/120 for PAL.
* If Manual is selected, set the shutter speed from the options :
- 1/30(1/25) ~ 1/30000. (Default : Manual 1/1000)
4. Focus Adjustment
When on, the default level is set automatically by controlling lens focus and based on
the installation and environment circumstances.
OSD Menu_Exposure
19
BACKLIGHT
2
OFF
HME HIGHLIGHT MASKING EXPOSURE
HME allows objects to appear clearly on the screen by
masking extremely bright areas. To setup HME, set the
level and color. The lower the setting, the darker the
masking areas have to be. Select from: 0 ~ 20.
Color: Set the color of the HME mask. Select from:
BLACK / WHITE / YELLOW / CYAN / GREEN /
MAGENTA / RED / BLUE / CUSTOMIZE
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
LENS AUTO
2
BACKLIGHT HME DRC OFF DEFOG OFF AGC 3 3D DNR OFF EXIT JUMP
EXPOSURE
BLC BACK LIGHT COMPENSATION
If BLC is selected, adjust the size and position of the mask:
- H-POS: Move the Zone position left or right. The higher the number,
the zone will move to the right.
- V-POS: Move the Zone position up or down. The higher the number,
the zone will move down.
BACKLIGHT
H-POS 6 V-POS 6 H-SIZE 8 V-SIZE 8 RETURN
- H-Size: Reset the zone‘s size horizontally. The higher the number,
the right side panel will move further to the right.
- V-Size: Reset the zone’s size vertically. The higher the number, the
bottom side panel will move further down.
OSD Menu_Exposure
20
EXPOSURE
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
LENS AUTO
3
4
6
DRC ( DYNAMIC RANGE COMPRESSOR )
3
DRC enables dark areas in images to become more visible without overexposing the bright areas to create one perfect image. Select from : OFF / LOW / MIDDLE / HIGH
DEFOG
4
Allows the camera to process a scene that is obscured by fog or weather conditions and provides a visibly improved image. AUTO / Manual : Select AUTO to have the WDR and DRC levels adjusted automatically. Set the DEFOG level from LOW / MIDDLE / HIGH.
AGC ( AUTO GAIN CONTROL )
5
0~10 - AGC enhances the picture brightness in low light conditions. A higher level AGC setting makes the images brighter, however, it could increase the amount of noise.
3D DNR ( 3D DIGITAL NOISE REDUCTION )
6
OFF/LOW/MIDDLE/HIGH - 3D-DNR reduces the noise on the screen in low light conditions and allows
BACKLIGHT OFF
DRC OFF DEFOG OFF
5
AGC 3 3D DNR OFF EXIT JUMP
for clearer images, even at night.
DEFOG
MODE AUTO LEVEL ____ RETURN
OSD Menu_Color
21
NOT USED
COLOR
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
EXIT JUMP
This is a License Plate Recognition Camera. As such, it has been programmed specically to register license plates only. For optimal results, this camera is set to B/W mode only. There is no Color mode on this camera. As a result, White Balance and Color Gain under the Color Menu and Day/Night Mode, Control and Delay options under the Day/Night Menu are not used for this camera.
OSD Menu_Day & Night
22
DAY/NIGHT
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
SMART IR 0 EXIT JUMP
1
SMART IR
0 ~ 20 : Enable Smart IR and set the level. Higher values will make Smart IR stronger.
OSD Menu_Function
23
1
2
3
4
1
2
3
FUNCTION
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
SHARPNESS 5 GAMMA 0.75
MIRROR OFF FLIP OFF EXIT JUMP
SHARPNESS
0 ~ 10 - Sets the image sharpness. The higher the number, the sharper the image.
GAMMA
0.45 ~ 0.75 - Select the desired gamma level. 0.75 is default setting.
MIRROR / FLIP
OFF MIRROR : Reects the camera horizontally. FLIP : Reects the camera vertically.
Mirror & Flip ONFlip ONMirror ONMirror / Flip OFF
OSD Menu_Motion
24
The camera can detect movement and display an alarm on the screen. when movement is detected.
1
2
3
4
5
6
1
MOTION
To use the motion detection settings, be fore Motion is ON.
2
DET WINDOW
MOTION ZONE setting
3
DET TONE
Four each dierent motion tone color available
4
MDRECT FILL
Color setting for operating motion zone
5
SENSITIVITY
The smaller the movement you want to detect, the higher the sensitivity value must be.
6
MOTION OSD
MOTION ZONE display. MOTION OSD interoperable with ‘DET TONE’ and ‘MDRECT FILL’.
7
TEXT ALARM
Setup a text to appear on the screen when motion is detected explaining the alarm situation.
- WINDOW MOTION: Will appear when a motion alarm is detected.
- CAMERA MOVING : Will appear if the camera is shaken abruptly.
8
SIGNAL OUT (ON / OFF)
- ON : ‘HIGH’ SIGNAL OUT upon ALARM.
- OFF : ‘SIGNAL OUT’ o regardless of ALARM
MOTION
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
MOTION OFF
DET WINDOW DET TONE ___ MDRECT FILL ___ SENSITIVITY 5 MOTION OSD OFF TEXT ALARM OFF SIGNAL OUT ON EXIT JUMP
DET WINDOW
WINDOW USE 0 WINDOW ZONE ON DET H-POS 1 DET V-POS 1 DET H-SIZE 58 DET V-SIZE 32 RETURN
OSD Menu_Privacy
25
You can hide some parts of the screen for privacy masking. A total of 16 dierent privacy masking zones are available. The cameras support square privacy masks or advanced polygon masks.
PRIVACY
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
PRIVACY OFF ZONE NUM 0 ZONE DISP ON
H-POS 12 V-POS 2 H-SIZE 3 V-SIZE 3 Y LEVEL 10 CB LEVEL 10 CR LEVEL 10
TRANS 0
EXIT JUMP
- ZONE NUM : Select the zone number between 0~15.
- ZONE DISP : Zone display ON/OFF
- H-POS : Move the Zone position Left or right. The higher the number, the zone will move to the right.
- V-POS : Move the Zone position up or down. The higher the number, the zone will move down.
- H-SIZE : Reset the zone‘s size horizontally. The higher the number, the right side panel will move further to the right.
- V-SIZE : Reset the zone’s size vertically. The higher the number, the bottom side panel will move further down.
- Y LEVEL : The higher the number, the brighter the color will appear.
- CR LEVEL : The higher the number, the more red tone will be added to the zone’s color. The lower the number, the more green will be added to the zone’s color.
- CB LEVEL : The higher the number, the more red tone will be added to the zone’s color.
* High CB Level + High CR Level = Pink * High CB Level + Low CR Level = Sky Blue * Low CB Level + High CR Level = Orange
- TRANS : Set the mask’s transparency level from 0~3. The default value is 0.
The lower the number, the more red will be added to the zone’s color.
OSD Menu_Setup
26
1
2
3
1
COMMUNICATION
Adjust the camera’s ID and Baudrate. Default Protocol is Pelco-D.
- CAM ID : Provide an ID number for the camera (0 ~ 255).
- BAUDRATE : 9600bps is default. Select the baudrate from the following options :
- SET DONE : Set the value of CAM ID and BAUDRATE.
2
CAM. TITLE
Add a name to the camera. Set the title by using the OSD joystick.
IMAGE RANGE
3
Image Range allows you to set the proper Black and White levels according to the external display you use.
- FULL : Display all BLACK level and WHITE level without compression.
- COMP : Display BLACK level and WHITE level with compression.
- USER : Reset the BLACK level by changing the OFFSET value.
2400/4800/9600/57600/115200 bps.
:
NOTE
Be sure to press “Save&Exit” button on the EXIT menu before saving.
SETUP
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
COMMUNICA CAM TITLE OFF IMAGE RANGE FULL FREQ 60Hz LANGUAGE ENG INITIAL OFF EXIT JUMP
COMMUNICA
CAM ID 1 BAUDRATE 9600 SET DONE OFF RETURN
OSD Menu_Setup
27
SETUP
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
COMMUNICA CAM TITLE OFF
4
6
4
FREQ
When the camera’s image appears to have ickering issues, change the frequency value to adjust the image.
5
LANGUAGE
Select from the following: English (Default), Chinese, Chinese (S), Japanese, and Koran.
6
INITIAL
Reset the camera to its default settings. Press and hold the select button for ve (5) seconds.
IMAGE RANGE FULL FREQ 60Hz LANGUAGE ENG
5
INITIAL OFF EXIT JUMP
OSD Menu_EXIT
28
1
EXPO MOTI PRIVRGB D&N FUNC SET EXIT
SAVE&EXIT
2
EXIT
1
SAVE & EXIT
Exit the OSD menu after saving the recent changes.
2
EXIT
Exit the OSD menu without saving any changes.
EXIT
Troubleshooting
29
Before sending your camera for repair, check the following or contact our technical specialist.
FOR NO VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the power supply and make sure the camera has the proper voltage and current.
FOR OUT-OF-FOCUS VIDEO
Check the Front case cover and the lens for dirt or ngerprints. Use a soft cloth and gently clean.
The use of a eld test monitor is recommended.
Specications
30
VIDEO
Image Sensor 1/3” CMOS Sensors
Active Pixels 1944(H) x 1092(V)
Scanning System Progressive scan
Freguency Signal Technology
Synchronization
Resolution
Minimum Scene Illumination S/N Ratio 55dB
Video Output
LENS
Focal Length & Lens Type IR Distance
OPERATIONAL
Shutter Speed 1/30(25) - 1/30,000
Backlight OFF/HME/BLC
60Hz / 50Hz
2.0 Megapixel Universal
Internal
1920x1080 (1080p30fps) F1.6 (30IRE): 0 Lux (B&W)
BNC (Universal : HD-A/HD-TVI/HD-CVI/CVBS)
6~50mm, P-Iris Vari-Focal 115ft
Specications
31
OPERATIONAL (CONT.)
Digital Noise Reduction OFF / LOW / MIDDLE / HIGH Day and Night NIGHT
Privacy Zones
Sharpness Gamma
Remote Control
ENVIRONMENTAL
Operating Temperature Operating Humidity
IP Rating
Other Certications FCC, CE, ROHS
ELECTRICAL
Power Requirements DC12V / AC24V Dual Voltage
Power Consumption DC12V : 6.12W, 510mA
MECHANICAL
Housing Material and Dimensions
Weight 1.79 lbs
0 ~ 10Auto Gain Control ON/OFF (4 Zones)Motion Detection
ON/OFF (16 Zones)
0 ~ 10
0.45 ~ 0.75
Coaxial (UTC)
-4°F ~ 122°F (
No more than 90% (Non-Condensing)
IP66
AC24V : 5.7W, 330mA
Aluminum, 10.4 x 3.81 in (
-20°C ~ 50°C)
264 x 96.7mm)
Limits & Exclusions
There are no express warranties except as listed. The warranter will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranti and fitness for particular purpose, are limited to the applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions or limitations listed above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state.
If the problem is not handled to your satisfaction, then write to the following address: Digital Watchdog, Inc.
ATTN: RMA Department 5436 W. Crenshaw Street Tampa, FL 33634
Service calls which do not involve defective materials or workmanship as determined by the Warranter, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser.
es, including the warranties of merchantability
32
Warranty Information
Digital Watchdog (referred to as “the Warranter”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows:
LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warranter will repair or replace the unit with a new or refurbished product at its option at no charge.
PARTS: In addition, the Warranter will supply replacement parts for the initial five (5) years and one (1) year on IR LED.
To obtain warranty or out of warranty service, please contact Representative at 1+ (866)446-3595 Monday through Friday from 9:00AM to 8:00PM Eastern Standard Time.
A purchase receipt or other proof of the original purchase date is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warranter or failures which result from accident, misuse, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer c improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.
abuse, neglect, mishandling, misapplication,
ontrols, improper operation, power line surge,
a Technical Support
33
Notes
34
Notes
35
East Coast Headquarters Office: 5436 W Crenshaw St, Tampa, FL 33634
West Coast Headquarters Office: 16220 Bloomfield Ave., Cerritos, CA 90703
PH: 866-446-35951 FAX: 813-888-9262
www.Digital-Watchdog.com Technical Support:
USA & Canada 1+ (866) 446-3595
International 1+ (813) 888-9555
French Canadian 1+ (514) 360-1309
Support Hours: Monday-Friday 9:00am to 8:00pm EST
Loading...