Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
12112013
Page 2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damage.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damage, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
2
Page 3
TABLE OF CONTENTS
Table of Contents
Introduction
Installation
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Easy Installation
Connecting to Monitors
4.0mm Fixed Lens
12x Digital Zoom
30ft Range IR with Intelligent Camera Sync
TDN (True Day and Night/IR Cut Filter)
WDR (Wide Dynamic Range)
3D-DNR (3D Digital Noise Reduction)
IP66 Certified (Vandal Resistant)
4
Page 5
PARTS & DESCRIPTION*
1
Bottom Case
2
Camera Gimbal
3
Camera Lens + IR LEDs
4
Dome Cover
5
Dome Cover Screws (x3)
1
2
4
5
3
5
Page 6
DIMENSIONS IN MILLIMETERS (IN)*
40.2
[1.58”]
74.3 [2.9”]
125.0 [4.9”]
6
Page 7
INSIDE THE BOX*
Included with your Camera
1
User Manual
2
Mounting Template for Metal Mount
3
Mount Template for Bolt Type Mount
4
3 Machine Screws and 3 Dry Wall Anchors
HD-SDI Vandal Dome Camera
DWC-HF21M4TIR
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
12112013
1
1
5
L-Wrench
6
2 Mounting Nuts & 2 Mounting Screws
7
Metal Mount Plate
8
Secondary Video-BNC Cable
2
2
34
3
4
5
6
87
7
Page 8
EASY CAMERA INSTALLATION*
1. Detach the camera’s cover dome from
the camera’s module by unscrewing the
three cover dome screws.
2. Use the camera or mounting template
to mark and drill the necessary holes in
the wall or ceiling.
3. Pull wires through and make
connections.
4. Using the two (2) included screws,
mount and secure the camera to the wall
or ceiling.
5. Secure the camera’s cover dome onto
the camera base to complete the
installation.
8
Page 9
EASY MOUNT BRACKET INSTALLATION*
Use the following installation instructions when
mounting the camera using the wall mount or
ceiling mount accesories.
1. Detach the camera’s cover dome from the
camera’s module by unscrewing the three
cover dome screws.
2. Using the metal mount plate, mark and drill
the necessary holes in the wall or ceiling.
3. Pull wires through and make connections.
4. Using the three (3) included screws, mount
and secure the camera to the wall or ceiling.
5. Attach the camera base to the metal
mount by snapping it into place using the two
metal handles.
6. Secure the camera’s cover dome onto the
camera base to complete the installation.
9
Page 10
EASY SOFT CEILING MOUNT INSTALLATION*
1. Detach the camera’s cover dome from
the camera’s module by unscrewing the
three cover dome screws.
2. Secure the two long mounting screws
to the camera’s base.
3. Using the camera or mounting
template, mark and drill the necessary
holes in the wall or ceiling.
4. Pull wires through and make
connections.
5. Mount the camera to the mounting
surface using the 2 mounting nuts.
6. Secure the camera’s cover dome onto
the camera base to complete the
installation.
10
MOUNTING SURFACE
Page 11
CONNECTING TO MONITORS*
Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC
Second Video Output
Power Connection - 12VDC.
All cameras are equipped with a second video output for on-site configuration.
HD-SDI Monitor
Monitor
11
Page 12
TROUBLESHOOTING
Before sending your camera for repair, check the following or contact our technical
specialist.
FOR NO VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the camera’s OSD menu.
Check the power supply and make sure the camera has the proper voltage and
current.
FOR OUT-OF-FOCUS VIDEO
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and
gently clean. Check the lens’ manual focal and zoom adjustment. The use of a field
test monitor is recommended.
12
Page 13
WARRANTY INFORMATION*
Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera
against defects in materials or workmanship as follows:
LABOR: For the initial two (2) years and one (1) year on IR LED from the original purchase
date, if the camera is determined to be defective, the Warrantor will repair or replace the
unit with a new or refurbished product at its option at no charge.
PARTS: In addition, the Warrantor will supply replacement parts for the initial two (2) years
and one (1) year on IR LED.
To obtain warranty or out of warranty service, please contact a Technical Support
Representative at 1-866-446-3595 Monday through Friday from 9:00AM to 8:00PM
Eastern Standard Time.
A purchase receipt or other proof of the original purchase date is required before warranty
service is rendered. This warranty only covers failures due to defects in materials and
workmanship which arise during normal use. This warranty does not cover damage which
occurs in shipment or failures which are caused by products not supplied by the Warrantor or
failures which result from accident, misuse, abuse, neglect, mishandling, misapplication,
alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate
signal pickup, maladjustment of consumer controls, improper operation, power line surge,
improper voltage supply, lightning damage, rental use of the product or service by anyone other
than an authorized repair facility or damage that is attributable to acts of God.
13
Page 14
LIMITS & EXCLUSIONS*
There are no express warranties except as listed. The warrantor will not be liable for incidental
or consequential damages (including damage to recording media without limitation) resulting
from the use of these products or arising out of any breach of the warranty. All express and
implied warranties, including the warranties of merchantability and fitness for particular
purpose, are limited to the applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitatons on how long an implied warranty lasts, so the exclusions or limitations listed above
may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights that vary from state-to-state.
If the problem is not handled to your satisfaction, then write to the following address:
Digital Watchdog, Inc.
ATTN: RMA Department
5436 W. Crenshaw Street
Tampa, FL 33634
Service calls which do not involve defective materials or workmanship as determined by the
Warrantor, in its sole discretion, are not covered. Costs of such service calls are the
responsibility of the purchaser.
14
Page 15
SPECIFICATIONS*
VIDEO
Image Sensor 1/2.8” CMOS Sensor
Total Pixels 2000 (H) x 1241 (V)
Synchronization Internal
Resolution 2.1 Megapixels (1920 x 1080) at 30fps
Minimum Illumination 0.0 Lux (IR On)
S/N Ratio 50dB (AGC off)
Video Output HD-SDI
LENS
Focal Length 4.0mm
Lens Type Fixed Lens
IR Distance 30ft Range IR
ENVIRONMENTAL
Operating Temperature -10oC ~ 55oC (14oF ~ 131oF)
Operating Humidity Less than 90% (Non-Condensing)
IP Rating IP66
ELECTRICAL
Power Requirement DC12V
Power Consumption LED Off: 2.0W, 166.7mA / LED ON: 2.7W, 225mA
MECHANICAL
Housing Material Aluminum Die-casting
Dimensions
Weight 1 lbs
(Protects against dust and high pressure water.)
∅
125 x 74.3mm (∅ 4.9 x 2.9”)
15
Page 16
5436 W Crenshaw St. Tampa, FL 33634
Tel : 866-446-3595 / 813-888-9555
Fax : 813-888-9262
www.Digital-Watchdog.com
technicalsupport@dwcc.tv
Technical Support Hours : Monday-Friday
9:00am to 8:00pm EST
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.