Digital Watchdog D2362DIR, D2363D, D2363TIR, D2367WD, D2367WTIR User Manual

...
5436 W Crenshaw St. Tampa, FL 33634
Tel: 866-446-3595 / 813-888-9555
Fax: 813-888-9262
www.Digital-Watchdog.com
technicalsupport@dwcc.tv
Technical Support Hours: Monday-Friday
8:30am to 8:00pm Eastern Time
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
ABOUT MANUAL
01302012
User Manual
D2362DIR, D2363D, D2363TIR D2367WD, D2367WTIR D2382TIR, D2365T Indoor Dome Camera
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and ammable substances from entering the camera. It can cause re, short- circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic elds.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface
The material of the mounting surface must be strong enough to support the camera.
PRECAUTIONS
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the menu setup of the camera. Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or ngerprints. Use a soft cloth and gently clean. Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
TROUBSHOOTING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful interference .when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING : Changes or modications are not expressly approved by the manufacture.
FCC COMPLIANCE
32
54
1/3” High Resolution CCD
540 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
Electronic Day and Night
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
AGC / BLC / AWB
Negative Imaging
Mirror Image Control
RS485 Built-In
Programmable Privacy Zone (4) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Secondary Video-BNC Output
1/3” High Resolution CCD
High Resolution 560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
Electronic Day and Night
Star-Light (Super Low Light Technology)
DRC (Dynamic Range Compressor)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
Negative Imaging
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
FEATURES
*
-
D2362DIR
FEATURES
*
-
D2363D
76
1/3” High Resolution CCD
High Resolution 560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
Electronic Day and Night
100ft Range IR with Intelligent Camera Sync
True Day and Night / TDN5
Star-Light (Super Low Light Technology)
DRC (Dynamic Range Compressor)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
Negative Imaging
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
FEATURES
*
-
D2363TIR
FEATURES
*
-
D2367WD
1/3” Sony Super HAD II CCD
560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
Electronic Day and Night
EWDR (Electronic Wide Dynamic Range)
Star-Light (Super Low Light Technology)
DSS (Digital Slow Shutter)
3D-DNR (3D Digital Noise Reduction)
DIS (Digital Image Stabilizer)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
98
FEATURES
*
-
D2367WTIR
1/3” Sony Super HAD II CCD
560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
True Day and Night / TDN5
EWDR (Electronic Wide Dynamic Range)
Star-Light (Super Low Light Technology)
DSS (Digital Slow Shutter)
3D-DNR (3D Digital Noise Reduction)
DIS (Digital Image Stabilizer)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
FEATURES
*
-
D2382TIR
1/3” Sony Super HAD II CCD
High Resolution 560TV Lines
OMNI-Focus 2.9~8.5mm 3X Motorized Zoom, Auto Iris 70ft Range IR with Intelligent Camera Sync
True Day & Night / TDN5 (Electro Magnetic Mechanism)
Max-DR (Electronic Wide Dynamic Range)
Enables the camera to capture perfect images in both bright and dark environments simultaneously.
3D-DNR (3D Digital Noise Reduction)
Produces less noise and more color during low-light application.
HME (Highlight Mask Exposure)
Masks overly exposed light to produce a true video image of any environment.
SLC (Side Light Compensation)
DIS (Digital Image Stabilizer)
Programmable Privacy Zone (6) & Motion Detection Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
No Fog or Condensation under Any Weather Condition
DIMENSION (mm)
*
109.6
103.1
41.3
6.5
145
117.0
125.0
5.0
4.5
91.0
91.0
85.0
85.0
L= 300mm
RS485 (Black+ & White -)
VIDEO(yellow)
BNC JACK
DC 12V or AC24V
5mm TWIST SOLDERING
RED
BLACK
FEATURES
*
-
D2365T
1110
1/3" Pixim Seawolf CMOS Sensor
690 Horizontal TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
TDN (True Day and Night/IR Cut Filter)
3D-DNR (3D Digital Noise Reduction)
Powerful Wide Dynamic Range
Smear Canceling Circuit
AGC / BLC / AWB
DIS (Digital Image Stabilizer)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-in Joystick
Low Power Consumption
Auto Sensing 24VAC/12VDC with Line Lock
Secondary Video-BNC Output
1312
Power Requirement *
Power Wire Maximum Distance
Wire Gauge 12VDC 24VAC
24 AWG 80feet 323feet
22 AWG 128feet 513feet
20 AWG 203feet 815feet
18 AWG 323feet 1295feet
16 AWG 514feet 2056feet
14 AWG 816feet 3264feet
12 AWG 1295feet 5183feet
10 AWG 2057feet 8228feet
Coaxial Cable Type Maximum Distance
RG59/U 750feet RG6/U 1,000feet RG11/U 1,500feet
Power Requirement
12VDC at 1A 24VAC at 500mA
INSTALLATION
*
Included with Digital Watchdog Camera:
1. User Manual
2. Mounting Template
3. Security L-Key
4. Single Sided Hex Key
5. Secondary BNC Cable for a Field Monitor
6. Four (4) Screws and Four (4) Dry Wall Anchors
1
3
2
4
5
7
6
Camera Installation
Use the Mounting Template when mounting the camera. Use the Security L-Key to loosen the Four Screws that secure the vandal-proof dome cover. Remove the cover; then, remove the inner screw holes to mount the camera.
NOTE: Keep the lens and the vandal proof cover free from dust or ngerprint.
INSTALLATION
*
A. Loosen the Screws (A) with the Security L-Key included with your camera.
B. Separate the Upper Case (B) from the Base (F).
C. Cut a hole in the ceiling for routing the cables.
D. Use the Mounting Template to drill the four
screw holes on the surface of the ceiling.
E. Pass the Power Cable (C) and the Video Cable (E)
from the camera unit through the hole in the ceiling.
F. Align the screw holes of the camera unit with
the holes in the ceiling. Secure the four screws.
G. Install and adjust the camera unit.
H. Assemble the Upper Case (B) and the Baes (F).
I. Put the upper case and the base together.
J. Tighten the outer Screws (A) using the Security
L-Key.
INSTALLATION AND ADJUSTMENT
*
-
D2382TIR
Included with DW Indoor Dome Camera:
1. User Manual
2. Mounting Template
3. One Security L-Key
4. One Single Sided Hex Key
5. Secondary BNC Cable for a Field Monitor
6. Two (2) Screws and Two (2) Dry Wall Anchors
7. IR Remote Controller
Camera Installation
Use the mounting template to mount the camera. Using the security L-key to loosen the four screws that secure the vandal proof dome cover, Remove the vandal proof dome cover to access the screw holes to mount the camera.
NOTE: Keep the lens and the vandal proof cover free from dust or ngerprint.
3-Axis Gimbal Adjustment
1
3
2
4
5
7
6
1514
CONNECTION
*
Video Output
BNC Cable
Main Monitor
Field Test Monitor
Spot Monitor Cable
DC12V / AC24V
CAMERA OSD & IR REMOTE CONTROLLER
*
NOTE:
Press [KEY] + [ID] (Default is “001” for ID=1) Press [ENT] to access the Menu
Note: The camera ID is a 3-digitnumber.
Key Button
Menu Access and Control
Zoom Function Control
ID Buttons
Motion Alarm On &OFF
Field Test Monitor Video Output
RS485 Connector
Dip Switch for the IR Remote Controller
Mini Joystick for the Menu Setup
LEFT
UP DOWN
RIGHT
-
D2382TIR
1716
1918
LENS ADJUSTMENT
*
A. Move the Zoom Lever until you get the desired position. B. Move the Focus Lever until you get the desired focus.
A. Zoom Lever
B.Focus Lever
:
D2362DIR, D2363D, D2363TIR, D2367WD, D2367WTIR, D2382TIR, D2365T
CAMERA SETTING & ON-SCREEN DISPLAY
*
Field Test Monitor Video Output
RS485 Connector
Dip Switch for the IR Remote Controller
Mini Joystick for the Menu Setup
LEFT
UP DOWN
RIGHT
2120
MODULE OSD MENU
*
-D2362DIR
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS SHUTTER BLC AGC
WB MODE D&N MODE
FUNCTION MOTION PRIVACY
MIRROR SHARPNESS GAMMA SLC HME DRC
ALARM MASK 1
MASK 2 MASK 3 MASK 4 COLOR SET
SYNC SETUP EXIT
SYNC CAMERA ID
TITLE EDIT TITLE RESET TITLE POSITION DPC SET LANGUAGE PC CONT.
EXIT SAVE & EXIT FACTORY RESET
EXPOSURE
BRIGHTNESS MANUAL (ELC LEVEL : 0 ~ 100) / DC (DC LEVEL : 0 ~ 31)
SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000
BLC
OFF / ON BLC (Back Light Compensation)
AGC
OFF / 12dB ~ 36dB AGC (Auto Gain Control)
COLOR
WB MODE
AWC / ATW / MANuAL / PUSHLOCK AWC is recommended.
R-Y GAIN 0 ~ 255
B-Y GAIN 0 ~ 255
DAY & NIGHT
Day & Night Mode
AUTO / COLOR / BW COLOR---->BW : Switching from COLOR to BW; If the number is higher, the camera will only
switch during a super low light condition.
BW ---->COLOR : Switching from BW to COLOR; This number should be always lower than
COLOR to BW
Read Time : time interval to switch from COLOR to BW
COLOR
B&W Mode : (BURST : OFF/ON) When the burst is OFF, the picture will have less noise.
OSD MENU
*
-D2362DIR
2322
FUNCTION
MIRROR OFF/ MIRROR
SHARPNESS 0 ~ 49
GAMMA USER / 0.45 / 0.6 / 1.00
SLC
OFF / ON (0 ~ 50) SLC (Side Light Compensation)
HME
OFF / ON (0 ~ 55) HME (Highlight Masking Exposure)
DIS OFF /ON
DIS (Digital Image Stabilizer)
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (0 ~ 55)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT(1 ~ 15) Motion Alarm Zoom-In Delay
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
COLOR SET BLACK / GRAY / COLOR 1~ 6
SYNC
SYNC MODE INTERNAL / AUTO
V-PHASE 0 ~ 199
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT
TITLE RESET
TITLE POS.
DPC
OFF / ON DPC ( Dead Pixel Cancellation)
LANGUAGE English / Chinese
PC CONT. OFF / ON
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
2524
MODUEL OSD MENU
*
-D2363D, D2363TIR
EXPOSURE
BRIGHTNESS 0 ~ 100
SHUTTER 1/60 / FLK / 1/250 ~ 10000 / SENS-UP x2 ~ x256
BLC/HME OFF / BLC / HME
AGC
HIGH / MIDDLE / LOW / OFF
AGC(Auto Gain Control)
STARLIGHT AUTO(x2 ~ x256) / OFF
NIGHT-UP NORMAL / HIGH
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
DAY & NIGHT
Day & Night Mode
AUTO : READ TIME(3~63) / S-LEVEL(0~100) / E-LEVEL(0~100) COLOR---->BW : B&W : Switching from COLOR to BW; If the number is higher, the camera
will only switch during a super low light condition
BW ---->COLOR : Switching from BW to COLOR; This number should be always lower than
COLOR to BW
Read Time : time interval to switch from COLOR to BW
COLOR
B&W Mode : BURST (OFF / ON) There is less noise when the BURST is OFF. SMART IR (OFF / ON)
C-SUP
Color Suppression :
Color will be reduced at low illumination, if the C-SUP Level is set higher. 0 ~ 63
A-SUP
Aperture Suppression : The sharpness of the edges will be reduced at low illumination, if
A-SUP level is set higher. 0 ~ 15
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS AE PREFERENCE BLC / HME AGC STARLIGHT NIGHT-UP
WB MODE R-Y GAIN B-Y GAIN
D&N MODE C_SUP A_SUP
FUNCTION MOTION PRIVACY
MIRROR SHARPNESS GAMMA FREEZE NEGATIVE D-ZOOM 3D DNR DRC
MOTION PRIVACY
SYNC SETUP EXIT
SYNC TITLE EDIT
PC CONTROL (RS485 Control)
LANGUAGE MONITOR OSD COLOR OMNI LENS DEFECT
EXIT SAVE & EXIT FACTORY RESET
OSD MENU
*
-D2363D, D2363TIR
2726
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00
FREEZE OFF / ON
NEGATIVE OFF / ON
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
3D-DNR
ON (0~100) / OFF 3D Digital Noise Reduction
DRC OFF / INDOOR / OUTDOOR
Dynamic Range Compressor
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (OMNI-Plus Camera Only)
MOTION
OFF
ON AREA SELECT (AREA 1~4) AREA SET (POSITION / SIZE) SENSITIVITY (0~40) MOTION TRACE (OFF / ON) MOTION VIEW (OFF / ON) RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
PRIVACY
OFF
ON AREA SELECT (1~8) AREA SET (POSITION / SIZE) COLOR (0~15) RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
EXIT JUMP EXIT / SAVE & EXIT / FACTORY SET
SETUP
TITLE EDIT OFF / ON
PC CONTROL (RS485 Control)
CAM ID / ID DISPLAY (OFF/ON) / BAUDRATE (2400 / 4800 / 9600) The protocol is xed pelco-D.
LANGUAGE ENG / KOR / JPN / CHN1 / CHN2 / RUS / FRAN / SPAN / ITAL
MONITOR
CRT / LCD Select LCD only if the camera is directly connected to the LCD monitor.
OSD COLOR 0 ~ 15
OMNI LENS
OFF (OMNI-Plus Camera Only)
ON ALARM / READ TIME / ALARM ZOOM / STAND BY / RETURN
DEFECT WHITE DEFECT CANCEL MODE
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT
SAVE&EXIT
FACTORY SET
2928
MODULE OSD MENU
*
-D2367WD, D2367WTIR, D2382TIR
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS SHUTTER BLC AGC MAX_DR STARLIGHT
WB MODE R-Y GAIN B-Y GAIN
D&N MODE C_SUP A_SUP
FUNCTION MOTION PRIVACY
MIRROR SHARPNESS GAMMA FREEZE NEGATIVE 3D DNR D-ZOOM SLC HME DIS
MOTION MASK 1
MASK 2 MASK 3 MASK 4 MASK 5 MASK 6
SYNC SETUP EXIT
SYNC CAMERA ID
TITLE DPC MONITOR LANGUAGE BAUDRATE OMNI LENS
EXIT SAVE & EXIT FACTORY RESET
OSD MENU
*
-D2367WD, D2367WTIR
EXPOSURE
LENS DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000
BLC
OFF / ON Back Light Compensation
AGC
HIGH / MIDDLE / LOW / OFF Auto Gain Control
MAX-DR OFF /ON (0~ 20) (Electronic Wide Dynamic Range)
STARIGHT
OFF / AUTO (x2 ~ x256) x32 is recommended.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
DAY & NIGHT
Day & Night Mode
AUTO/ COLOR/ BW / EX-CONT COLOR---->BW : Switching fromcolor to BW; if the number is higher, the camera will only switch during a
super low light condition.
BW ---->COLOR : Switching from BW to color; this number should always be lower than COLOR to BW Read Time: Timeinterval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) Whenthe burst is OFF will make less noise
C-SUP
Color Suppression :
Color will be reduced at low illumination, if the C-SUP Level is higher. 0 ~ 100 (Not Available
when DNR is On.)
A-SUP
ApertureSuppression:
The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher. 0 ~ 100
(Not Available when DNR is On.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
3130
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00 / USER
FREEZE OFF / ON
NEGATIVE OFF/ ON
3D-DNR
OFF / LOW / MIDDLE / HIGH 3D Digital Noise Reduction
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
SLC OFF / ON Side Light Compensation
HME
OFF / ON Highlight Masking Exposure
DIS
OFF / ON Digital Image Stabilizer
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15) Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
V-PHASE 0 ~ 199
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT OFF / ON
DPC
OFF / AUTO DPC (Dead Pixels Cancellation)
MONITOR CRT / LCD
LANGUAGE English,Japanese, Chinese
BAUDRATE
2400 / 4800 / 9600 / 14400 / 19200 / 38400. Protocol is Pelco-D(xed cannot be changed;hardcodedinto the DSP)
OMNI LENS OFF / 1 ~ 10 (OMNI-Plus Cameras Only)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
OSD MENU
*
-D2382TIR
EXPOSURE
LENS DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER 1/160 /1/100 / FLC / 1/250 ~ 10000 / SENS-UP x2 ~ x250
BLC OFF / ON , BLC (Back Light Compensation)
AGC
HIGH / MIDDLE / LOW / OFF AGC (Auto GainControl)
MAX-DR OFF /ON (0~ 20) (Electronic WideDynamic Range)
STARIGHT AUTO (x2 ~ x250) / OFF (x32 is recommended.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
DAY & NIGHT
Day & Night Mode
AUTO/ COLOR/ BW / EX-CONT COLOR---->BW : Switching fromcolor to BW; if the number is higher, the camera will only switch during a
super low light condition.
BW ---->COLOR : Switching from BW to color; this number should always be lower than COLOR to BW Read Time: Timeinterval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) Whenthe burst is OFF will make less noise
C-SUP
Color Suppression :
Color will be reduced at low illumination, if the C-SUP Level is higher. 0 ~ 100 (Not Available
when DNR is On.)
A-SUP
ApertureSuppression:
The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher. 0 ~ 100
(Not Available when DNR is On.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00 / USER
FREEZE OFF / ON
NEGATIVE OFF/ ON
3D-DNR OFF / LOW / MIDDLE / HIGH, 3D-DNR (3D Digital Noise Reduction)
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
SLC OFF / ON SLC (Side Light Compensation)
HME OFF / ON HME (Highlight Masking Exposure)
DIS
OFF / ON DIS (Digital Image Stabilizer)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (Omni-Focus Lens Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15) Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Motion Alarm Setup
1. Go to Motion Menu
2. Set Motion to “ON”
3. Click [Set Windows] and set your area of the motion detection
4. Press the Left Arrow button, until you exit back to the Motion Menu
5. Zoom out to the farthest you want the camera to zoom out and press [7](Wide)
6. Zoom in to the farthest you want the camera to zoom in and press [8](Tele)
7. Click [Exit Jump] then click [Save & Exit]
8. Once you are out of the menu press [9](ON/OFF) to activate motion alarm
3332
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
V-PHASE 0 ~ 199
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT OFF / ON
DPC
OFF / AUTO DPC (Dead Pixels Cancellation)
MONITOR CRT / LCD
LANGUAGE English,Japanese, Chinese
BAUDRATE
2400 / 4800 / 9600 / 14400 / 19200 / 38400. Protocol is Pelco-D(xed cannot be changed;hardcodedinto the DSP)
OMNI LENS OFF / 1 ~ 10 (for OMNI-PLUS CAMERA only)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
MODULE OSD MENU
*
-D2365T
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS AE PREFERENCE WDR BLC AGC STARLIGHT METER ZONE
WB MODE COLOR GAIN
D&N MODE
FUNCTION MOTION PRIVACY
MIRROR SHARPNESS GAMMA 3D DNR D-ZOOM
MOTION PRIVACY
SYNC SETUP EXIT
SYNC PC CONTROL
TITLE LANGUAGE MONITOR OMNI LENS FLUORESCENT DIGITAL VIDEO OUT
EXIT SAVE & EXIT FACTORY RESET
3534
OSD MENU
*
-D2365T
FUNCTION
MIRROR OFF / MIRROR / V-FLIP / ROTATE
SHARPNESS -8 ~ 8
GAMMA 25(0.25) ~ 100(1.0)
3D DNR MOVIE / INFO
D-ZOOM
ZOOM:1(x1.0) ~ 12(x8)
PAN(-100~100)/TILT(-100~100) (Digital Zoom/Pan using the camera mini joystick)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION
MOTION
OFF / ON (ACTIVITY THR (0 ~ 255))
SET MOTION ZONES
- 1 ZONE / 1 ~ 2 ZONE / 1 ~ 3 ZONE / 1 ~ 4 ZONE
- ADJUST ZONE 1 (MOVE/MAKES WIDE/MAKES NARROW)
- ADJUST ZONE 2 (MOVE/MAKES WIDE/MAKES NARROW)
- ADJUST ZONE 3 (MOVE/MAKES WIDE/MAKES NARROW)
- ADJUST ZONE 4 (MOVE/MAKES WIDE/MAKES NARROW)
RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
PRIVACY
OFF
ON
- AREA 1 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 2 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 3 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 4 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 5 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 6 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXPOSURE
BRIGHTNESS -48 ~ 60
AE PREFERENCE OUTDOOR / INDOOR
BLC OFF / BLC (PERCENTILE 10 ~ 50)
WDR LOW / NORMAL / MEDIUM / HIGH / CUSTOM
AGC LOW / MEDIUM / HIGH / CUSTOM
STARLIGHT x2 ~ x64 / OFF
METER ZONE ADJUST ZONE 1 / ADJUST ZONE 2
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE
AWC / ATW(2,000k~11,000K) / PUSH LOCK / MANUAL (KELVIN:2,000L~11,000K /R/B:RED:-20~20 BLUE:-20~20)
COLOR GAIN -8 ~8
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
DAY & NIGHT
D&N MODE
AUTO / AUTO(EXT) / COLOR / B&W
- AUTO Mode:(READ TIME:0~255/S-LEVEL:0~60/E-LEVEL:0~60/BW AGC:0~60)
- AUTO(EXE) Mode:(Option-IR LED Mode)
- COLOR Mode
- B&W Mode
BW BURST (OFF / ON)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
3736
SYNC
SYNC
INT1(SYNC to 59.64Hz)/INT2(SYNC to 60.01Hz)/LL LIMIT/V PHASE/RETURN)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
SETUP
PC CONTROL
CAM ID:1 ~ 255 ID DISPLAY : OFF / ON PROTOCOL : PELCO-D BAUDRATE : 2400/4800/9600/19200 RETURN
TITLE
OFF / ON
(TITLE/ID POSITION(UP-LEFT/UP-CENTER/UP-RIGHT/DOWN-LEFT/
DOWN-CENTER/DOWN-RIGHT)
LANGUAGE ENGLISH
MONITOR CRT / LCD
OMNI LENS
OFF
ON ALARM OFF ALARM ON(READ TIME(5~15)/ALARM ZOOM(4~214)/STAND BY(0~214)/RETURN)
FLUORESCENT
OFF / CRR(Manual Lens, Color Rolling/Flickerless Mode)/ CRR2(DC Lens, Color Rolling Mode)
DIGITAL VIDEO OUTPUT
DIGITAL OUT (OFF / ON)
FIELD ORDER (NORMAL / REVERS)
FRAME RPT (OFF / 2X / FREEZE)
RETURN
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT
SAVE & EXIT
FACTORY SET
SPECIFICATIONS*
Model D2362DIR
Camera TYPE Color/BW
Plastic 18IR-LED Day/Night Digital Dome Camera
Mount Surface
Image Size 1/3"
Pixels-Total 811(H) x 508(V) Pixels-Eective 768(H) x 494(V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED On 0.0 Lux Functions BLC ON / OFF (Area Setting)
AGC ON / OFF (Gain Adjust) AWB ATW / AWC / MANUAL / PUSH LOCK DRC ON / OFF Motion Detection ON / OFF Privacy Zone 4 Programmable Zone / Size
Lens Focal Length 3.3 ~ 12mm Varifocal Auto Iris Lens Resolution Horizontal 540 TV Lines [at TDN (B/W) :560 TV Lines] Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) S/N Ratio S/N Ratio 50dB OSD OSD YES Environmental Conditions Operating Temperature -10
o
C
~ +55
o
C
(14
o
F
~ 131
o
F
)
Humidity Less than 90%
Power Power Requirement 12VDC
Power Consumption
0.9W, 75mA / 2.9W, 242mA (LED ON)
Physical Specication Dimensions(φ x H) 110.3 X 134.9mm, 4.34 X 5.31in
3938
4140
SPECIFICATIONS* SPECIFICATIONS*
Model D2363TIR
Camera TYPE Color/BW Indoor Dome Camera
Mount Surface
Image
Device 1/3” High Resolution CCD Pixels-Total 811 (H) x 508 (V) Pixels-Eective 768 (H) x 494 (V)
VV Scanning
System 525 line, 2:1Interlace Horizontal Frequency Internal Mode 15,734Hz Horizontal Frequency Line-Lock Mode
15.750Hz Vertical Frequency Internal Mode 59.94Hz Vertical Frequency Line-Lock Mode 60Hz
Min. Scene Illumination
IR-LED On IR Distance
0.0LUX
100ft Range
Functions
Sens-up OFF / AUTO(x256) DNR OFF / AUTO AGC OFF / LOW / MIDDLE / HIGH AWB
ATW/AWC/INDOOR/OUTDOOR/MANUAL/PUSH LOCK Motion Detection ON /OFF (Area, Sensitivity, Trace) Privacy Zone 8 Programmable Zone / Size
Lens Focal Length
3.3~12mm
Resolution Horizontal 540 TV Lines Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) S/N Ratio S/N Ratio 52dB OSD OSD YES
Environmental Conditions
Operating Temperature -10
o
C
~ +55
o
C
(14
o
F
~ 131
o
F
)
Humidity Less than 90%
Power
Power Requirement 12VDC / 24VAC
Power Consumption
12VDC:1.96W, 163.3mA / 24VAC: 2.2W, 91.7mA
12VDC:4.3W, 358.3mA/24VAC:3.0W, 125mA(LED ON)
Physical Specication Dimensions(H x L) 110.3 X 134.9 mm (4.34x5.31in) Certications CE, FCC, RoHS Certied
Model D2363D
Camera TYPE Color/BW Indoor Dome Camera
Mount Surface
Image
Device 1/3” High Resolution CCD Pixels-Total 811 (H) x 508 (V) Pixels-Eective 768 (H) x 494 (V)
VV Scanning
System 525 line, 2:1Interlace Horizontal Frequency Internal Mode 15,734Hz Horizontal Frequency Line-Lock Mode
15.750Hz Vertical Frequency Internal Mode 59.94Hz Vertical Frequency Line-Lock Mode 60Hz
Min. Scene Illumination F1.2 0.14 Lux
Functions
Sens-up OFF / AUTO(x256) DNR OFF / AUTO AGC OFF / LOW / MIDDLE / HIGH AWB
ATW/AWC/INDOOR/OUTDOOR/MANUAL/PUSH LOCK Motion Detection ON /OFF (Area, Sensitivity, Trace) Privacy Zone 8 Programmable Zone / Size
Lens Focal Length
3.3~12mm
Resolution Horizontal 540 TV Lines Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) S/N Ratio S/N Ratio 52dB OSD OSD YES
Environmental Conditions
Operating Temperature -10
o
C
~ +55
o
C
(14
o
F
~ 131
o
F
)
Humidity Less than 90%
Power
Power Requirement 12VDC / 24VAC Power Consumption
12VDC: 1.96W, 163.3mA / AC24V: 2.2W, 91.7mA
Physical Specication Dimensions(H x L) 110.3 X 134.9mm (4.34x5.31in) Certications CE, FCC, RoHS Certied
4342
SPECIFICATIONS*
Model D2367WD
Camera TYPE Color/BW I ndoor Dome Camera
Mount Surface
Image Device Super HAD II CCD
Size 1/3” Pixels-Total 811 (H) x 508 (V) Pixels-Eective 768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination F1.2 0.14 Lux [Color], 0.03 Lux [B/W] Functions DIS ON/OFF
AGC HIGH / MIDDLE / LOW / OFF EWDR OFF / ON Mirror OFF / MIRROR / V-FLIP / ROTATE STAR-LIGHT OFF / AUTO (x2 ~ x256) Privacy Zone 6 Programmable Zone / Size
Lens Focal Length 3.3~12mm Varifocal Auto Iris Lens Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW] Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) S/N Ratio S/N Ratio 50dB OSD OSD YES Environmental Conditions Operating Temperature -10
o
C
~ +55
o
C
(14
o
F
~ 131
o
F
)
Humidity Less than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption
12VDC: 1.8W, 150mA / 24VAC: 2.4W, 100mA
SPECIFICATIONS*
Model D2367WTIR
Camera TYPE Color/BW I ndoor Dome Camera
Mount Surface
Image Device Super HAD II CCD
Size 1/3” Pixels-Total 811 (H) x 508 (V) Pixels-Eective 768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED On 0.0Lux
IR Distance 100ft Range
Functions AGC HIGH / MIDDLE / LOW / OFF
STAR-LIGHT AUTO (x2 ~ x250) / OFF 3D-DNR OFF / ON HME OFF / ON DIS OFF / ON
Privacy Zone 6 Programmable Zone / Size Lens Focal Length 3.3~12mm Varifocal Auto Iris Lens Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW] Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) S/N Ratio S/N Ratio 50dB OSD OSD YES Environmental Conditions Operating Temperature -10
o
C
~ +55
o
C
(14
o
F
~ 131
o
F
)
Humidity Less than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption
12VDC: 1.8W, 150mA / 24VAC: 2.4W, 100mA 12VDC: 4.6W, 383.3mA / 24VAC: 4.9W, 204.2mA
SPECIFICATIONS* SPECIFICATIONS*
Model D2382TIR
Camera TYPE Color/BW I ndoor Dome Camera
Mount Surface
Image Device Super HAD II CCD
Size 1/3" Pixels-Total 811 (H) x 508 ( V) Pixels-Eective 768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz Min. Scene Illumination IR-LED on 0.0 Lux Functions BLC ON/OFF
AGC HIGH/ MIDDLE / LOW /OFF
MAX-DR OFF / ON
Mirror OFF / MIRROR / V-FLIP / ROTATE
STAR-LIGHT AUTO (x2~ x250) / OFF
3D-DNR OFF / ON
SLC OFF / ON
HME OFF / ON
Motion Detection OFF / ON (Area / Sensitivity)
Privacy Zone 6 Programmable Zone / Size Lens Focal Length
OMNI-Focus2.9~8.5mm 3x Motorized Zoom, Auto Iris
Resolution Horizontal 560 TV Lines [Color]; 580 TV Lines [BW] Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load) S/N Ratio S/N Ratio 50dB OSD OSD YES Environmental Conditions Operating Temperature -10
o
C ~ +55oC(14oF ~ 131oF)
Humidity Less than 90% Power Power Requirement 12VDC / 24VAC
Power Consumption
165mA / 360mA; 4.90Watts / 4.96Watts
Model D2365T
General Spec
CCD Type 1/3" 420K Pixels Color
Total number of pixels 768(H) X 548( V)
Minimum Illumination
0.22Lux (F1.2, 30IRE-COLOR)
0.0Lux (LED ON)
Resolution
H: 690 TV Lines Eective
Electric Spec
Voltage
DC 12[V] (11.0[ V] ~ 20.0[V])
AC 24[V] (20.0[ V] ~ 30.0[V])
Power Consumption DC12V-3.1W / AC24V-3.2W
COMMON
General Spec
Shutter speed 1/25 ~ 1/30,720 sec
S/N Ratio 53dB or More(AGC OFF)
Gamma 0.45
Sync System Internal / Line Lock
Mechanical Spec
Operation Temperature -10oC +50oC (14oF ~ 131oF)
Storage Temperature -20
o
C +70oC
Operation Humidity Under 90% (Non-condensing)
4544
4746
Digital Watchdog (referred to as “the Warrantor”) warrants the Camera Series against defects in materials or workmanship as follows.
LABOR : For the initial ve (5) years from the date of original purchase,
if the camera is determined to be defective, the Warrantor will repair or replace the unit, with new or refurbished product at its option, at no charge.
PARTS : In addition, the Warrantor will supply
replacement parts for the initial ve (5) years.
To obtain warranty or out of warranty service, please contact a Technical Support Representative at 1-866-446-3595 Monday through Friday from 8:30AM to 8:00PM Eastern.
A purchase receipt or other proof of the original purchase date is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modication, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.
WARRANTY INFORMATION* LIMITS AND EXCLUSIONS*
There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages, including without limitation and damage to recording media, resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and tness for particular purpose, are limited to the applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specic legal rights, and you may also have other rights that vary from state to state.
If the problem is not handled to your satisfaction, then write to the Address listed on the next page.
Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser.
Loading...