Digital Watchdog DW-BJCUBE9T-LX, DW-BJCUBE2T-LX, DW-BJCUBE12T-LX, DW-BJCUBE18T-LX, DW-BJCUBE3T Quick Start Manual

...
Page 1
Quick Start Guide
State of the art hyper-optimized video management platform designed for ease, speed and efciency.
Blackjack® Cube — Up to 16 (Cube-LX) and 64 (Cube) 2.1MP Cameras (1080p True HD Resolution)
DW-BJCUBE2T-LX DW-BJCUBE4T-LX DW-BJCUBE6T-LX DW-BJCUBE9T-LX DW-BJCUBE12T-LX DW-BJCUBE18T-LX
Blackjack Cube
DW-BJCUBE3T DW-BJCUBE4T DW-BJCUBE6T DW-BJCUBE9T DW-BJCUBE12T DW-BJCUBE18T
Blackjack Cube-LX Blackjack Cube
Default Login Information for DW Spectrum® IPVMS
Username: admin Password: admin1234
WHAT’S IN THE BOX
CUBE Server 1 Set Keyboard and Mouse 1 Set
Quick Start Guide 1 Set Power Cable 1 Set
NOTE: Download All Your Support Materials and Tools in One Place
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results for applicable part numbers will
populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals, Quick Start Guides (QSG), software and rmware will appear in the results.
Attention: This document is intended to serve as a quick reference for initial set-up. See the DW Spectrum full manual for more information on features and functionality.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Page 2
BLACKJACK CUBE HARDWARE
F3
Front
F1 F2
Back
B5
B9
B12
F1 HDD LED F2 Power Button / Power LED F3 5.25" Bay F4 USB 2.0 Port F5 Microphone Jack F6 Headphone Jack F7 USB 2.0 Port
B1
B1 AC Power Socket B2 Kensington Lock
B2
B3 DVI-I Output B4 HDMI HD Output B5 USB 3.0 Ports B6 Microphone Jack
B3
B7 Line-Out Jack B8 Line-In Jack B9 WAN & USB 2.0 Ports
(Onboard LAN –
F4
F5
F7
F6
B11
B10
B7B4 B6
B8
B10 Clear CMOS Button
recommended for internet connection use)
B11 USB 2.0 Ports B12 LAN (Second Card –
recommended for camera
Default Login Information for Pre-Installed DW Spectrum® IPVMS
connection use)
Username: admin Password: admin1234
WARNING For an optimal system conguration, it is recommended that a UPS (Uninterruptible Power Supply) be used to power the setup.
Dual monitors are not recommended due to CPU performance. To connect two monitors to the Cube, go to the display setup to activate the second monitor.
SPECIFICATIONS CUBE
MODEL Blackjack CUBE-LX Blackjack CUBE
Maxi mum IP Ca meras 16 64
Included IP Licenses 4 4
Form Factor Desk top
Operating System
CPU Intel® i3® Processor Intel® i5® Processor
Memory
NIC 2x Gigabit Ethernet (RJ45) 2x Gigabit Ethernet (RJ45)
System Max Vi deo Storage Rate ( Mbps) 80 Mbps 360 Mb ps
Storage
Video-Out
Pre-Loaded VMS Software DW Spectrum® IPVMS
Unlimited Remote Clients Cross Pl atfor m - Windows®, Linux® and Mac
Mobile Apps iOS® and Android
Keyboa rd & Mouse Included
Power 300W **
Operating Temperature and Humidity 41°F~104°F / 20-9 0% RH
Dimension (WxDxH) (inches) 8.5" x 13" x 7. 5"
Warran ty 5 Year Limite d
Windows® 10 64 bit --- DW-BJCUBEX T
Linux® Ubuntu
Maximum Hard Drives 3 x HDD
Maximum Storage 18TB
Outputs DVI-D or True HD Output
Video C ard Onboard Intel HD Graphics
Resolution HD 1080p
®
Option: DW- RME8 - Upgrade Me mor y to 8GB*
DW-BJCUBEXT-LX ---
4GB
®
®
* Availab le at time of initia l order o nly / ** U PS Reco mmend ed
16G B
2
Page 3
Quick Start Guide
SETTING UP THE CUBE
STEP 1: Connect Peripherals, power and network
1. Connect a monitor, USB keyboard, USB mouse and network cable to the camera network(B12 on the diagram)
* Cable for the Local Network should be connected after the IP settings are congured.
2. Connect the server to an appropriate power source. Recommended to use 750VA or higher UPS system.
3. Turn on the server if the server does not turn on automatically.
(Press the Power Button on the front of the Cube. F2 on the diagram).
* Connecting the power cable to the live power source may turn on the server automatically
3
Page 4
STEP 2: Congure Date and Time
STEP 2: Configure Date and Time
Windows
1. Double click Date and Time icon on the Desktop.
2. Change Time zone if not correct (default is UTC-08:00 Pacific Time)
Windows
1. Double click Date and Time icon on the Desktop.
2. Change Time zone if not correct (default is UTC-08:00 Pacic Time)
Click Change date and time… to update the date and time if they are not correct.
* Verify the Time zone before updating the date and time. Time may show 2 or 3 hours off due to incorrect Time zone.
Press OK after adjusting to the correct date and/or time.
4. Press OK to close Date and Time when done.
4
Page 5
Quick Start Guide
Linux
1. Update Date and Time by clicking on the time on the upper right-hand corner then click “Time & Date settings…”
2. If the server will be connected to the Internet, leave Set the Time to “Automatically from the Internet” and update the Location to the correct Time Zone. Enter the nearest major city to select the correct Time Zone. If it shows
3. Click X on upper left corner of the Time and Date window when done.
* Closing the window will automatically save the changes made.
5
Page 6
STEP 3: Congure Network
DNS Servers
Not Applicable
*
Camera Network and Local Network cannot be on the same network.
3. Click Internet Protocol Version 4 (TCP/IPv4) and click Properties
NOTE If you are not sure what information to enter, contact your Network Administrator or Internet Service Provider
for the information.
NOTE The Blackjack Cubes network settings are set to DHCP as default.
DNS Servers
Not Applicable
*
Camera Network and Local Network cannot be on the same network.
NOTE If you are not sure what information to enter, contact your Network Administrator or Internet Service Provider
for the information.
NOTE The Blackjack Cubes network settings are set to DHCP as default.
Not Applicable
Please have the following information ready before starting the network conguration.
Camera Network Local Network (LAN)
IP Address
Subnet Mask / Netmask
Default Gateway / Gateway Not Applicable
DNS Servers Not Applicable
* Camera Network and Local Network cannot be on the same network.
NOTE The Blackjack Cube’s network settings are set to DHCP as default.
NOTE If you are not sure what information to enter, contact your Network Administrator or Internet Service
Provider for the information.
Windows
1. Double click Network Connections on the Desktop
2. Right click on the Ethernet with cable connected and click Properties.
3. Click Internet Protocol Version 4 (TCP/IPv4) and click Properties
6
Page 7
Quick Start Guide
4. Select Use the following IP address (Use the following DNS server addresses will be selected automatically)
5. Enter IP address and Subnet mask of the camera network. (do not enter anything for the Default gateway, Preferred DNS server and Alternate DNS server.
NOTE It must be the same network as the cameras and must not be the same network as the local network.
Contact your network administrator for more information.
4. Select Use the following IP address (Use the following DNS server addresses will be selected automatically)
5. Enter IP address and Subnet mask of the camera network. (do not enter anything for the Default gateway, Preferred DNS server and Alternate DNS server.
NOTE It must be the same network as the cameras and must not be the same network as the local network.
Contact your network administrator for more information.
6. Click OK to close then click Close to go back to Network Connections.
Local Network
7. Right click on the other Ethernet, the one with network cable unplugged, and click Properties.
8. Click Internet Protocol Version 4 (TCP/IPv4) and click Properties
7
Page 8
9. Select Use the following IP address (Use the following DNS server addresses will be selected automatically)
10. Enter IP address and Subnet mask of the camera network.
8
Page 9
Quick Start Guide
11. Click OK to close then click Close to go back to Network Connections.
12. Connect a network cable to the Ethernet port B9 on the diagram (page 2) to the switch on the local network.
13. Close the Network Connections by clicking X on the upper right corner of Network Connections.
11. Click OK to close then click Close to go back to Network Connections.
12. Connect a network cable to the Ethernet port B8 on the diagram (page 2) to the switch on the local network.
13. Close the Network Connections by clicking X on the upper right corner of Network Connections.
Linux
1. Double-click the Network icon on the Desktop
NOTE The Blackjack Cube’s network settings are set to DHCP as default.
2. Select ‘Wired’ that has arrows pointing up and down from the list (If neither of the “wired” are showing arrows up and downs, then make sure the network cable is connected to the PoE switch on the camera network from STEP 1)
3. Click ‘Options’ at the bottom of the window.
4. Click on the ‘IPv4 Settings’ tab.
5. From the drop-down menu, select connection type (“Method”) as Manual.
6. Click ‘Add’ next to Addresses.
9
Page 10
* Gateway is not required on the camera network.
NOTE It must be the same network as the cameras and must not be the same network as the local network.
Contact your network administrator for more information.
NOTE It must be the same network as the cameras and must not be the same network as the local network.
Contact your network administrator for more information.
* Gateway is not required on the camera network.
NOTE It must be the same network as the cameras and must not be the same network as the local network.
Contact your network administrator for more information.
* Gateway is not required on the camera network.
7. Enter IP Address then press Tab on the keyboard to move to Netmask.
8. Ignore any populated values and enter the valid Netmask value, then press Tab on the keyboard to move to the Gateway.
9. Enter the Gateway address if required then press Enter on the keyboard.
* Gateway is not required on the camera network.
NOTE It must be the same network as the cameras and must not be the same network as the local network.
Contact your network administrator for more information.
10. Click ‘Save’ to save the settings.
11. In the Network Settings main page, make sure the Wired Status is marked as “Connected” or Managed” With the
IP Address displayed.
Local Network
12. Select Wired with picture of network port and repeat 2 to 8 of STEP 3 Congure Network.
13. Click on the DNS Servers eld box and enter DNS server address.
14. Click Save.
15. Connect a network cable to the Ethernet port B9 on the diagram (page 2) to the switch on the local network.
16. Verify the network is Connected.
NOTE If you are not connecting to the Blackjack® from within the same network, you may be required to perform port
forwarding on your router to access the server. Contact your Network Administrator or Installer for additional information
10
Page 11
CONFIGURE CAMERAS USING DW IP FINDER
Windows
Refer to the camera’s QSG to congure Digital Watchdog camera’s IP address using DW IP nder.
Spectrum Client
LINUX-BASED SOFTWARE MANUAL LAUNCH
To launch the DW Spectrum® Software on the Linux-Based Cube:
Quick Start Guide
Linux OS
OP T ION 1: Double-click the DW Spectrum® desktop icon. OPTION 2: Go to the dashboard on the top left side.
Search ‘DW’. Click the DW icon.
OR
WINDOWS-BASED SOFTWARE MANUAL LAUNCH
To launch the DW Spectrum® Software on the Windows-Based Cube:
OP T ION 1: Double-click the DW Spectrum® desktop icon. OPTION 2: Go to ‘Start’ on
the bottom left and select
DW Spectrum® in the
OR
Digital Watchdog folder
11
Page 12
SETTING UP DW SPECTRUM® MEDIA SERVER
Login : admin Password : admin1234
STEP 1: Initial run from Blackjack® server
1. Open DW Spectrum® Client by double click on the DW Spectrum icon
2. Click on the precongured server.
3. Enter password and click connect.
* Default password : admin1234 (case sensitive)
12
Page 13
STEP 2: To rename the server
1. Right click on the server name listed on the Resources then click Server Settings.
Quick Start Guide
2. Go to General tab, then type in the new server name in the Name eld and click OK.
13
Page 14
STEP 3: To check for update
1. Click on the menu then click System Administration.
2. Go to Updates tab. Click Update System if turned orange.
14
Page 15
Quick Start Guide
* If you are on the latest version, it will say “You have the latest version installed” and the Update System button will be greyed out.
3. Click OK when update is completed.
STEP 4: Enter License
1. Go to System Administration then click License tab.
2. Enter License Key then click Activate License button. (Internet connection required)
* Click on Activate Trial License if you have not purchased the valid license.
15
Page 16
3. Click OK to when the License is activated.
STEP 5: Configure recording
1. Right click on the camera to setup recording, then click Camera Settings.
16
Page 17
2. Go to Recordings tab.
Quick Start Guide
3. Click to turn on recording.
4. Congure Schedule Settings for Quality, FPS and Recording Type.
5. Click and drag mouse over the Recording Schedule to assign the recording setting.
17
Page 18
* Click on All to apply to the all schedules.
6. Red dot will appear next to the camera when the recording is started.
18
Page 19
STEP 6: Backuping Database
1. Go to System Administration and click General tab.
Quick Start Guide
2. Click Create Backup… button.
3. Navigate to the folder where to save and enter name of the backup le then click save.
* Strongly recommend to also backup to the external storage media.
NOTE: More information and instructions are available in the Spectrum 3.0 Manual.
19
Page 20
TROUBLESHOOTING TIPS
Windows
Problem Possible Solutions
My camera does not auto-discover
Videos are slow
My camera appears disconnected
I can’t get playback video from my camera
I get an ‘unauthorized’ message on my camera
1. Is the camera in the same L AN network as the Media Server?
2. Is your camera compatible with DW Spectrum? (Refer to our website for full list of supported cameras.)
3. Is the camera updated to its latest rmware?
4. If your camera is integrated with DW Spectrum via ONVIF, make sure ONVIF is enabled on your camera.
5. Try adding the camera manually.
6. Try rebooting the server after installation. Allow up to 2 minutes for the server to map your network and detect all supported devices.
1. Are you accessing the same cameras from multiple clients? (LAN & WAN)
2. Do you have a Gigabit network? Check your network speed.
1. Under camera settings, make sure the user name and password are correct.
2. Under the camera settings, use the ‘Ping’ button to make sure the camera is connected to the network properly.
3. If you can connect to the camera’s web viewer, try rebooting the camera and/or restore it to factory default.
4. Make sure your camera is using the latest rmware available.
5. Make sure that the camera is connected to the same network as the server.
6. If you are connecting to a camera that is integrated with DW Spectrum via the ONVIF protocol (see list), make sure ONVIF is enabled.
7. Make sure your user has permissions to view that specic camera.
1. Do you have network connection between client and server (in case server and client are not on the same machine)?
2. Make sure your user has playback viewing permissions for the selected channel.
3. Make sure the camera is set to a recording mode that would provide recorded video for the selected time and environment.
4. On the server side, check the media server log to make sure the camera you are trying to watch has not been unexpectedly disconnected.
1. Make sure the camera’s user name and password are properly entered in the camera’s general information under the camera settings menu.
2. If necessary, try rebooting the camera to apply the camera’s user name and password.
SYSTEM REQUIREMENTS
Recommended Specs for the Full Client
Processor Intel Core i5 or greater
Video Card
Resolution 1920 x 1080
RAM 16G B
NIC 1Gbps Ethernet
OS Suppor ted – Client
Linux OS
* Except Storage Server version
Important: OS not listed will be not be supported by DW™ Tech Suppor t
Intel HD Graphics 2500 (or higher) with 1GB Dedicated Memor y Recommend NVIDIA or AMD graphics card with 2GB or more memory
Windows
Windows Servers*
Linux Ubuntu 14.04, Ubuntu 16.04
Mac OSX 10.11, O S X 10 .12
7 Home, 7 Standard, 7 Pro, 7 Ultimate, 8/8.1 Standard, 8/8.1 Pro, 8.1 Enterprise, 10 Home/Pro/Enterprise**
Any versions of 2008, any versions of 2008 R2, any versions of Server 2012, any versions of Server 2012 R2
Rev Date: 03/19
Tel: +1 (866) 446-3595
Fax: (813) 888-9262
www.digital-watchdog.com sales@dwcc.tv
Specications and pricing are subject to change without notice.
Copyright © Dig ital Watc hdog. All right s reser ved.
Loading...