Digital Projection MERCURY 5000HD User Manual

MERCURY 5000HD

Super High Brightness Digital Video Projector User’s Manual

16:9 widescreen display

Digital Projection MERCURY 5000HD

Declaration of Conformity

Directives covered by this Declaration

89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC and 93/68/EEC. 73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.

Products covered by this Directive

Large Screen Projector type MERCURY 5000HD

Basis on which Conformity is being declared

The products identified above comply with the protection requirements of the above EU directives, and the manufacturer has applied the following standards.

EN 50081-1:1992 - EMC Generic Emission Standard for Residential, Commercial and Light Industrial Equipment.

EN 50082-1:1992 - EMC Generic Immunity Standard for Residential, Commercial and Light Industrial Equipment.

EN 55022:1995 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipment.

EN 60950:1992 - Specification for Safety of Information Technology Equipment, including Electrical Business equipment.

The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage directive has been compiled by the signatory below and is available for inspection by the relevant enforcement authorities. The CE mark was first applied in 2004.

Signed:

Authority: D.J. Quinn, Director - Product Development

Date: 23 April 2004

Attention!

The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which must be observed when these products are taken into service to maintain compliance with the above directives. Details of these special measures are available on request, and are also contained in the product manuals.

iii

Important Information Digital Projection MERCURY 5000HD

Precautions

Please read this manual carefully before using your Digital Projection MERCURY 5000HD Projector and keep the manual handy for future reference. Your serial number is located on the side of your projector. Record it here:

CAUTION

To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED Digital Projection SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED Digital Projection SERVICE PERSONNEL.

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Digital Projection in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Important Safeguards

These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away from dust and moisture. Do not tilt the projector more than ±12° from side to side, as this will reduce lamp life. The projector may be tilted forwards or backwards as necessary.

±12°

360°

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

3. GSGV Acoustic Noise Information Ordinance:

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.

In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cable is not supplied with this equipment please contact your supplier.

• IBM is a registered trademark of International Business Machines Corporation.

• Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.

• Other product and company names mentioned in this user's manual may be the trademarks of their respective holders.

3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal components.

5. Handle your projector carefully. Do not hold the lens hood and the terminal covers. Dropping or jarring can damage internal components.

6. Do not place heavy objects on top of the projector.

Digital Projection MERCURY 5000HD Important Information

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

b. The projector must be installed by qualified technicians

in order to ensure proper operation and reduce the risk of bodily injury.

c. In addition, the ceiling must be strong enough to support

the projector and the installation must be in accordance with any local building codes.

d. Please consult your dealer for more information.

To Dealer or Installer:

To prevent the projector from falling, install it in a place and fasten it in a way with sufficient strength to support the combined weight of the projector (25 kg / 55 lbs), the lens and any mounting hardware, for an extended period of time as well as to withstand earthquakes.

Power Supply

1. The projector is designed to operate on a power supply of 100-240 V 50/60 Hz AC. Ensure that your power supply fits this requirement before attempting to use your projector.

2. Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire.

3. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.

4. Do not touch the power plug with wet hand. Doing so can cause electrical shock or fire.

5. Do not touch the power plug during a thunder storm. Doing so can cause electrical shock or fire.

Cleaning

1. Unplug the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily

soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful

not to scratch or mar the lens.

CAUTION

Do not unplug the power cable from the wall outlet under any one of the following circumstances. Doing so can cause damage to the projector:

• While the message "Please wait a moment." appears. This

message will be displayed after the projector is turned off.

• Immediately after the power cable is plugged into the wall

outlet (the POWER indicator has not changed to a steady orange glow).

• Immediately after the cooling fan stops working (The cooling

fan continues to work for 90 seconds after the projector is turned off).

CAUTION

• Do not try to touch the ventilation outlets as they can

become heated while the projector is turned on.

• Do not put the projector on its side when the lamp is turned

on.

Doing so may cause damage to the projector.

• Before shipping this projector, remove the lens and attach

the lens hood cap.

The Lens Shift mechanism may encounter damage caused by improper handling during transportation.

• Do not eject a PC card or LAN card while its data is being

accessed. Doing so can damage your PC card or LAN card.

Lamp Replacement

• To replace the lamp, follow all instructions provided on page 9-2.

• Be sure to replace the lamp when the message "The Lamp has reached the end of its usable life. Please replace the lamp." appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. CAUTION: Do not touch them as the pieces of glass may cause injury. If this happens, contact your Digital Projection dealer for lamp replacement.

• Allow a minimum of 90 seconds to elapse after turning off the projector. Then turn off the main power and disconnect the power cable and allow 15 minutes to cool the projector before replacing the lamp.

• The projector must be operated with two lamps installed regardless of whether or not the lamp is active. Failure to do so may degrade the performance of the projector such as screen flicker or loss of lamp life. If one lamp has reached the end of its usable life, replace it with a new one as soon as possible.

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at least 3 inches (10 cm) of space between your projector and a wall, except to the rear and the ventilation outlet on the right side, where there should be at least 12 inches (30cm) of space.

2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified Digital Projection service personnel.

3. Do not place any liquids on top of your projector.

4. When using a LAN cable:

For safety, do not connect to the connector for peripheral device wiring that might have excessive Voltage.

CAUTION

• Do not look into the lens while the projector is on. Serious damage to your eyes could result.

• Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpredictable outcome such as fire or injury to the eyes.

• Do not cover the lens with the supplied lens hood cap or equivalent while the projector is on. Doing so can lead to melting of the cap and possibly burning your hands due to the heat emitted from the light output.

Digital Projection MERCURY 5000HD

Table of Contents Digital Projection MERCURY 5000HD

1. Introduction

What's in the Box? .................................................................. 1-2

Introduction to the Projector ................................................ 1-3

Getting to Know Your Projector ............................................ 1-4

Control Panel Features ............................................................... 1-6

Terminal Panel Features ............................................................. 1-7

Remote Control Features ....................................................... 1-9

Remote Control Precautions ..................................................... 1-11

Remote Control Battery Installation .......................................... 1-11

Operating Range for Wireless Remote Control ........................ 1-11

Using the Remote Control in Wired Operation ......................... 1-12

2. Installation

Setting Up Your Projector ...................................................... 2-2

Screen Size and Projection Distance .......................................... 2-2

Lens Shift Adjustable Range ................................................. 2-4

Optional Lens Installation ..................................................... 2-5

Making Connections ............................................................... 2-6

Connecting Your PC or Macintosh ............................................. 2-6

To connect Scart Output ............................................................. 2-7

Connecting an External Monitor .................................................. 2-7

Connecting Your DVD Player ..................................................... 2-8

Connecting Your VCR or Laser Disc Player .............................. 2-9

Connecting to a Network .......................................................... 2-10

Connecting the Supplied Power Cable ....................................... 2-11

3. Projecting an Image (Basic Operation)

Turning on the Projector........................................................ 3-2

Selecting a Source .................................................................. 3-3

Adjusting the Picture Size and Position .............................. 3-3

Correcting the Horizontal and Vertical Keystone Distortion

(3D Reform) ............................................................................. 3-4

Optimizing RGB Picture Automatically ................................. 3-6

Turning Up or Down Volume ................................................. 3-6

Turning off the Projector........................................................ 3-7

4. Convenient Features

Turning Off the Image and Sound......................................... 4-2

Enlarging and Moving a Picture ........................................... 4-2

Getting the On-line Help and Information ........................... 4-2

Using a USB Mouse ................................................................ 4-3

Using a USB HUB Function .................................................. 4-3

Changing Background Logo ................................................ 4-4

Making Freehand Drawings on Projected Image

(ChalkBoard) ........................................................................... 4-4

5. Using the Viewer

Making the Most out of the Viewer Function ....................... 5-2

Operating the Viewer Function from the Projector

(playback) ................................................................................. 5-3

6. Using the Projector in a Network

Introduction ............................................................................. 6-2

Supported Equipment ............................................................ 6-3

Equipment Connections and Settings ................................. 6-4

Software Installation ............................................................... 6-5

Starting/Exiting the Software ................................................. 6-6

Troubleshooting ..................................................................... 6-7

Double Stacking and Link Mode

Stacking and Connecting the Projectors ............................. 7-2

Adjusting and Registering Signals to Be Projected ........... 7-5

Adjusting the Lens Shift, Zoom and Focus to Clearly Display

all projected patterns ............................................................. 7-5

Link Mode Setting ................................................................... 7-5

List of Menu Items Available in Link Mode .......................... 7-6

8. Using the On-Screen Menus

Basic Menu Operation ............................................................ 8-2

List of Direct Button Combinations ..................................... 8-3

Menu tree .................................................................................. 8-4

Menu Descriptions & Functions ............................................ 8-7

Source Select ............................................................................. 8-7

Adjust Source ............................................................................. 8-7

Picture ................................................................................. 8-8

Video Adjust ........................................................................ 8-8

Picture Management ............................................................ 8-9

Image Options ................................................................... 8-10

Option Adjust ..................................................................... 8-10

Signal Type .........................................................................8-11

Sound ......................................................................................... 8-11

Ref. Adjust ............................................................................... 8-12

Using 3D Reform .............................................................. 8-12

Screen Type ...................................................................... 8-12

Reference White Balance ................................................. 8-12

Reference Color Correction .............................................. 8-12

Factory Default ........................................................................ 8-13

Projector Options ...................................................................... 8-13

Menu .................................................................................. 8-13

Setup ................................................................................. 8-15

Lamp Settings ................................................................... 8-18

Link Mode .......................................................................... 8-18

LAN Mode .......................................................................... 8-19

Password ........................................................................... 8-23

Security ............................................................................. 8-24

Tools .......................................................................................... 8-25

Timer .................................................................................. 8-25

Capture .............................................................................. 8-27

PC Card Files .................................................................... 8-27

ChalkBoard ........................................................................ 8-27

Help .......................................................................................... 8-27

Contents ............................................................................ 8-27

Source Information ............................................................ 8-27

Projector Information ......................................................... 8-28

Test Pattern .............................................................................. 8-28

9. Routine Maintenance

Replacing the Lamp ................................................................ 9-2

Replacing or Cleaning the Filter .......................................... 9-3

Cleaning the Cabinet and the Lens ...................................... 9-3

10. Appendix

USB Memory Device or

USB Memory Card Reader Support ......................................

Troubleshooting ................................................................... 10-3

Specifications ........................................................................ 10-5

Cabinet Dimensions ............................................................. 10-7

Pin Assignments of D-Sub RGB Input Connector ............ 10-7

Compatible Input Signal List .............................................. 10-8

REMOTE 1 Connector ........................................................... 10-9

PC Control Codes and Cable Connection ...................... 10-10

Cable Connection ................................................................... 10-10

PC Control Connector (D-SUB 9P) ........................................ 10-10

Using Software Keyboard .................................................. 10-10

Operation Using an HTTP Browser ................................... 10-11

10-2

vii

Digital Projection MERCURY 5000HD

viii

Introduction

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

What's in the Box? ....................................1-2

Introduction to the Projector ....................1-3

Getting to Know Your Projector ...............1-4

Control Panel Features ...................................................................................... 1-6

Terminal Panel Features.................................................................................... 1-7

Remote Control Features .......................... 1-9

Remote Control Precautions .......................................................................... 1-11

Remote Control Battery Installation ............................................................... 1-11

Operating Range for Wireless Remote Control ............................................ 1-11

Using the Remote Control in Wired Operation ............................................. 1-12

1. Introduction Digital Projection MERCURY 5000HD

What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your Projector.

NOTE: Lenses are optional. Order lenses from your Digital Projection dealer.

ZOOM

MAGNIFY/

FOCUS

Projector (102-834)

ENTER

OSD

MUTE

SOUND

E-LIST/

PICTURE

SHUT

ADJUST

ADDRES

MENU/

PICT/

LENS

UTO

POSI/

PIXEL

AMP/

KEYST

OFF

INFO

HELP

PQR

GHI

MNO

DEF

INPUT

ABC

VWX

STU

WHITEBAL.

JKL

PROJECTOR

IMAGE/

OFF

TEST

POWER

Remote control (102-161) and batteries (AAx2)

CTL

CANCEL

UNDO

Power cable for United Kingdom (AC 230V) (102-180)

Power cable for Japan (AC 100V) (102-164)

16Mb PC card (102-112)

User Supportware (102-191)

Power cable for North America (AC 120V) (102-165)

Power cable for Europe (AC 230V) (102-163)

User Manual (103-510)

Remote cable (102-162)

DVI cable (102-166)

Important Information (103-511)

1-2

Digital Projection MERCURY 5000HD 1. Introduction

Introduction to the Projector

This chapter introduces you to the MERCURY 5000HD high end fixed installation projector and describes key features and controls.

Congratulations on Your Purchase of the MERCURY

5000HD projector

The MERCURY 5000HD is a compact three chip, HD DLP™ projector, utilising the unique Dark Metal DMD™ technology from Texas Instruments. With the MERCURY 5000HD you will be able to project images up to 500" (measured diagonally) from your DVD player, VCR, satellite hookup, HDTV source, PC, Workstation or Macintosh computer (desktop or notebook) and images from you digital camera PC Card or compact flash memory. The MERCURY 5000HD incorporates integrated networking access through the RJ45 input or provides for wireless network connectivity from an optional wireless network PC card. With extensive input and output panels, full suite of quick-change lenses and a full function remote, the MERCURY

5000HD will let you immerse yourself in large screen viewing.

Features you’ll enjoy on the MERCURY 5000HD:

• Integrated RJ45 connector for wired networking ability

• Two optional modular card slots allow for future projector growth with the ability to add additional input cards

• Dual PC card slots provide for optional wireless/wired network connectivity or PC Card usage

• Email projector error status information to selected individuals

• Power Horizontal and Vertical lens shift for optical display corrections

• Digital Projection DigiView for enhanced video image display, more vibrant colors and blacks richer with detail

• DigiScale enhanced image technology for increased projector versatility that provides for horizontal, vertical and diagonal keystone correction (allows for positioning the projector in off center locations in the room and still get aligned images)

• Display 16:9 or 4:3 information and fill the screen

• HDTV (1080p, 1080i, 720p) and SDTV (576p, 576i, 480p, 480i) compatibility

• Native resolution of 1280 x 720, 16:9 widescreen display.

• Intelligent lamp technology offers up to six user lamp settings to maximize light output or lamp life and provide for built in redundancy

• Smart security settings for password protection, control panel lock, menu lock and PC card protection key to help prevent unauthorized access and adjustments to the projector

• ADA508 and Executive Order 13221 Federal Government compliance *

• DigiView 10-bit video decoder for expanded black levels and adaptive gamma correction

• Digital photo viewer to display larger than life images from your digital cameras PC card or compact flash card

• Double stackable for built in redundancy and high light output requirements

• Two timer settings - On/Off with programming or Sleep timer that counts down at selected intervals

• 12V low voltage Screen Trigger output

• Easy set up and operation

• Eco-mode™ lamp technology for increased lamp life and energy savings

• DigiView for uncompromising display of video and data. Improves white level, color accuracy, dynamic range, and display of varying levels of black in an image

• Wireless remote control operation

• External control via RS232, USB or Network

• DigiScale intelligent pixel blending technology provides for extremely accurate image compression and HDTV (1920x1080) display resolution*2.

• Supports most IBM VGA, SVGA, XGA, Macintosh, component signal (YCbCr/YPbPr) or other RGB signals within a horizontal frequency range of 15 to 100 kHz and a vertical frequency range of 48 to 120 Hz. This includes NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60 and SECAM standard video signals

NOTE: Composite video standards are as follows: NTSC: U.S. TV standard for video in U.S. and Canada.

NTSC4.43: TV standard used in Middle East countries. PAL: TV standard used in Western Europe. PAL-M: TV standard used in Brazil. PAL-N: TV standard used in Argentine, Paraguay and Uruguay. PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

*1This projector meets ADA508 compliance, the latest

American government regulation which provides for closed captioning, including a menu system that can be viewed by colorblind users. This model also meets Executive Order 13221 requirement for standby operation, which consumes less than 1 watt.

*2HDTV 1080p (1920x1080), HDTV 1080i (1920x1080), and

1600x1200 are displayed with DigiScale.

1-3

1. Introduction Digital Projection MERCURY 5000HD

Getting to Know Your Projector

Remote control sensor

Ventilation outlet

Terminal panel (Left)

Lens (optional)

Remote control sensor

Rear cover

Controls

Mounting holes for stacking adaptors

Remote control sensor

Terminal panel (Right)

AC INPUT Connect the supplied power cable’s three-pin plug here.

Remote control sensor

Ventilation inlet

1-4

Digital Projection MERCURY 5000HD 1. Introduction

Ventilation outlet

Remote control sensors

2 x 5/8 UNC mounting holes (maximum depth 1¼”)

4 x M8 mounting holes (maximum depth 16mm)

Feet (rotate to fine-adjust the height and level of the projector)

1-5

1. Introduction Digital Projection MERCURY 5000HD

Control Panel Features

1. POWER Button (ON / STAND BY)( )

Use this button to turn the power on and off when the main power is supplied and the projector is in standby mode or idle mode.

NOTE: To turn on or off the projector, press and hold this button for a minimum of two seconds.

2. POWER Indicator

When this indicator is green, the projector is on; when this indicator is orange, it is in standby or idle mode. See the Power Indicator section on page 10-3 for more details.

3. STATUS Indicator

If this light blinks red rapidly, it indicates that an error has occurred, the lamp cover is not attached properly or the projector has overheated. If this light remains orange, it indicates that you have pressed a cabinet key while the Control Panel Key Lock is enabled. See the Status Indicator section on page 10-3 for more details.

4. LAMP Indicator 1/2

If this light blinks red rapidly, it's warning you that the lamp has reached the end of its usable life. After this light appears, replace the lamp as soon as possible (See page 9-2). See the Lamp Indicator section on page 10-3 for more details.

5. PC CARD Access Indicator 1/2

Lights while accessing a PC card.

6. 3D REFORM Button

Press this button to enter 3D Reform mode to correct the keystone (trapezoidal) distortion, and make the image square. Press to toggle between Cornerstone and Keystone adjustment mode.

NOTE: Pressing and holding this button for a minimum of 2 seconds will reset 3D Reform correction setting values to zero.

7. AUTO ADJUST Button

Use this button to adjust Position-H/V and Pixel Clock/Phase for an optimal picture. See page 3-6.

8. MENU Button

Displays the menu.

9. SELECT (+) (–) / Volume Buttons

: Use these buttons to select the menu of the item you

: Use these buttons to change the level of a selected

10. ENTER Button

Executes your menu selection and activates items selected from the menu.

11. CANCEL Button

Press this button to exit "Menus". Press this button to return the adjustments to the last condition while you are in the adjustment or setting menu.

12. LENS SHIFT Button

Adjust the lens offset by shifting the projected image position horizontally and / or vertically.

13. ZOOM Button (+/-)

Zoom the lens in and out.

14. FOCUS Button (+/-)

Adjust the lens focus.

wish to adjust. When no menus appear, these buttons work as a volume control.

menu item. A press of the button executes the selection. When the menus or the Viewer tool bar is not displayed, these buttons can be used to select a slide, or to move the cursor in Folder List or Slide List.

1-6

Digital Projection MERCURY 5000HD 1. Introduction

Terminal Panel (left) Features

1. RGB 1 Connectors [R/Cr, G/Y, B/Cb, H/V, V] (BNC) Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of external equipment. If using a component with a combined sync (SYNC) output, connect it to the H/V terminal. When using luminance and color-difference signals of HDTV and DVD, connect Pr/Cr to the R, Y to the G and Pb/Cb to the B input of the projector.

DVI AUDIO Input Mini Jack (Stereo Mini) This is where you connect the audio output from your computer when connected to the DVI input. A commercially available audio cable is required.

4. RGB OUT Connector (Mini D-Sub 15 Pin) You can use this connector to loop your computer image to an external monitor from the RGB 1 or 2 input source.

5. VIDEO IN Connector (BNC) Connect a VCR, DVD player, laser disc player, or document camera here to project video.

VIDEO AUDIO Input Jacks R/L (RCA) These are your left and right channel audio inputs for stereo sound from a Video source.

6. S-VIDEO IN Connector (Mini DIN 4 Pin) Here is where you connect the S-Video input from an external source like a VCR.

NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.

S-VIDEO AUDIO Input Jacks R/L (RCA) These are your left and right channel audio inputs for stereo sound from an S-Video source.

7. AUDIO OUT Jacks R/L (RCA) You can use this connector to output sound from the currently selected input source (RGB 1, RGB 2, DVI (DIGITAL), Video or S-Video). Output sound level can be adjusted in accordance with the sound level of the internal speaker.

8. Slot 1/2 For optional RGB or SDI board.

RGB 1 Audio Input Jacks (RCA) L/MONO: This is your left channel audio input for stereo sound coming from the RGB Input 1 source. This also serves as your monaural audio input.

R: This is your right channel audio input for stereo sound from the RGB Input 1 source.

2. RGB 2 Connector (Mini D-sub 15 Pin) Connect your computer or other analog RGB equipment such as IBM compatible or Macintosh computers. This also serves as a component input connector that allows you to connect a component video output of component equipment such as a DVD player. This connector also supports SCART output signal. See page 2-9 for more details.

RGB 2 Audio Iput Mini Jack (Stereo Mini) This is where you connect audio output from your computer or DVD player connected to the RGB2 input. A commercially available audio cable is required.

3. DVI IN Connector (DVI-D 24 Pin) This connector can be used to accept digital signal output from a computer with a DVI connector.

1-7

1. Introduction Digital Projection MERCURY 5000HD

Terminal Panel (right) Features

1. USB Port [MOUSE/HUB] (Type A) Connect a USB mouse. You can operate the menu or Viewer with a USB mouse via this port.

• A USB-supported scanner or PC peripheral can be connected to this port. (USB Hub Function. See page 4-3)

2. USB Port [PC] (Type B) Connect this port to the USB port (type A) of your PC using a USB cable. This port also serves as a PC Control port by using Dynamic Image Utility 2.0 included on the supplied CD-ROM.

3. PC CARD Slot 1/2 Insert a PC card, commercially available flash memory card or Digital Projection optional wireless LAN card here. There are two slots: Slot 1 and Slot 2.

4. PC CARD Eject Button 1/2 Press to eject a PC card partially. Each slot has its own eject button: 1 and 2.

5. PC CONTROL Connectors (Mini D-Sub 9 pin) For system expansion such as PC-Control using Dynamic Image Utility included on the supplied User Supportware CDROM or RS232C control from an external control system.

6. SC. TRIGGER Mini Jack When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the screen controller and the screen will go up.

NOTE: To use this feature, you must turn on the Screen Trigger function. See page 8-17.

Stereo mini cable (not supplied)

NOTE: Screen controllers are supplied and supported by screen manufacturers.

NOTE: Do not use this jack for anything other than intended use. Connecting wired remote control to the SC. TRIGGER Mini Jack causes damage to the remote control.

7. LAN Port (RJ-45) This port is typically used for UTP Ethernet/Fast Ethernet. Use this connector to control the projector on a LAN. See page 2-12.

8. REMOTE 1 (Mini D-Sub 15 Pin) This terminal allows external control of the projector by use of contact closure. See page 10-9.

9. REMOTE 2 Mini Jacks (IN/OUT)

IN: wired remote control input.

OUT: for daisy-chaining multiple projectors and operating them with the same remote control. To do so, connect to a second projector’ s IN terminal to relay the input at the IN terminal of the first projector until all the projectors are connected.

10. AC IN When you plug the supplied power cable into an active wall outlet and turn on the Main Power switch, the POWER indicator turns orange and the projector is in standby mode. See page 3-2. Three types of power cable are supplied with this projector: a three-pin type for the United Kingdom b three-pin type for U. S. A. and Canada. c Two-pin type for Europe and Japan.

Tip (12V)

Ring (0V)

Sleeve (ground. 0V)

IN: connect to the external equipment such as a PC or control system.

OUT: for daisy-chaining multiple projectors and operating them with the same external equipment. To do so, connect to a second projector’ s IN terminal to relay the input at the IN terminal of the first projector until all the projectors are connected.

1-8

Digital Projection MERCURY 5000HD 1. Introduction

Remote Control Features

POWER INPUT

OFF

ABC1DEF2GHI

WHITE BAL.

AMP

JKL4MNO5PQR

STU7VWX

E-LIST/

13 28

TEST

PROJECTOR

IMAGE/

PICTURE

OFF

ADJUST

KEY ST./

LENS

POSI/

15 17

PIXEL SOUND

AUTO

PICT/

ADDRESS

MENU/

UNDO

CANCEL

FOCUS

CTL

SHUT

MAGNIFY/

HELP

MUTE

ENTER

ZOOM

INFO

OSD

1. POWER ON Press and hold this button for a minimum of two seconds to turn on the projector when the main power is supplied and the projector is in standby mode or idle mode.

2. POWER OFF

Press and hold this button for a minimum of two seconds to turn off the projector.

3. MENU Press to display the main menu. While pressing and holding CTL, press this button to display the Remote Control ID dialog box to specify the remote control ID. See page 7-2.

4. ENTER

YZ/

Executes the menu selection and activates items selected from the menu. When the slider or dialog box is displayed: Pressing this button confirms adjustments/setting and returns to the previous menu display.

23 14

5. Select (Up/Down/Left/Right)

: Use these buttons to select the menu of the item you

wish to adjust. When no menus appear, these buttons work as a volume control.

19 18

: Use these buttons to change the level of a selected

menu item. A press of the button executes the selection.

Pressing and holding CTL, then pressing button works as a Back Space key in the entry screen. Pressing and holding CTL, then pressing this button moves the menu, slider, toolbar or dialog box.

6. ADJUST WHITE BAL. Press to display the Picture Management screen.

7. ADJUST PICTURE Press to display the Picture adjustment screen. Pressing this button sequentially selects adjustment screens.

8. IMAGE/PROJECTOR Press to display the Image Option screen. Pressing this button sequentially selects Image Options screens. While pressing and holding CTL, pressing this button rotates Projector Options screens.

9. Source / Input Press to select input or to name a signal.

1 Selects RGB 1 input. 2 Selects RGB 2 input. 3 Selects DVI (DIGITAL) input. 4 Selects VIDEO input. 5 Selects S-VIDEO input. 6 Selects Viewer input 7 Selects LAN input 8 Selects OPTION SLOT 1* (optional RGB or SDI board) 9 Selects OPTION SLOT 2* (optional RGB or SDI board) 0 Sequentially selects: RGB1 (VIDEO)→ RGB1 (S-VIDEO)

* This button toggles between input 1 and 2.

NOTE: While pressing and holding CTL, pressing this button switches to the selected signal found in the Entry List.

1-9

→

1. Introduction Digital Projection MERCURY 5000HD

10. UNDO Press to return the adjustments and settings to the previous condition. While pressing and holding CTL, pressing this button clears the entire menus or adjustment/setting screen. At this time the adjustments/settings are stored in memory except the items on the setting screen with "OK" and "Cancel" buttons such as the Menu and the Setup screen.

11. CANCEL Press to exit the menu. Press this button with CTL to return to the previous menu without closing adjustment/setting screen while the menus appear. This feature allows you to adjust or set several items concurrently.

12. INFO Displays the "Source Information" or "Projector Information" window. This button toggles between these two windows. While pressing and holding CTL, pressing this button stores lens position settings.

13. TEST Press to display the test pattern. Pressing this button sequentially selects test patterns.

21. KEYSTONE (R) Press to display the Keystone Correction (3D Reform) screen. This button toggles between “Cornerstone” and “Keystone”. When the test pattern is displayed, while pressing and holding CTL, pressing this button displays a red test pattern.

NOTE: Pressing and holding this button for a minimum of two seconds will reset 3D Reform correction setting values to zero.

22. AMPLITUDE (G) Service personnel only. When the test pattern is displayed, while pressing and holding CTL, pressing this button displays a green test pattern.

23. ENTRY LIST (B) Press to display the Entry List screen. Pressing and holding CTL and then ENTRY LIST buttons simultaneously, enters a signal in the Entry List when you are not displaying a test pattern. When the test pattern is displayed, while pressing and holding CTL, pressing this button displays a blue test pattern.

14. HELP Provides online help.

15. PIXEL Displays the Position/Clock screen to adjust the clock and phase.

16. AUTO (RGB only) Press to adjust Position-H/V and Pixel Clock for an optimal picture.

17. POSITION Press to display the Position screen; press again to display the Blanking screen. While pressing and holding CTL, pressing this button displays the Lens Shift adjustment screen.

18. MUTE SOUND Turns off the sound for a short period of time. Press again to restore the sound.

19. MUTE OSD Press to turn off the on-screen display. Press again to restore the on-screen display.

NOTE: You can also turn off the on-screen display forcibly by pressing and holding CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ; doing this again restores it. In this case any adjustment will still change the projector's memory settings. This mode is available even when input is switched to another or the power is turned off the main power.

24. FOCUS (+/–) While pressing and holding CTL, pressing this button allows you to adjust the lens focus.

25. MAGNIFY/ZOOM (+/–) Magnify the size of a target portion. While pressing and holding CTL, pressing this button allows you to zoom the lens in and out.

26. CTL Used in conjunction with other buttons, similar to a shift key on a computer.

N O

29 27

27. Remote Jack Connect your remote cable here for wired operation.

20. MUTE PICTURE Press to turn off the picture for a short period of time. Press again to restore the picture.

28. Backlight Switch When using the remote control wirelessly: Turns the backlight on and off. If no button is pressed within 30 seconds, the backlight will turn off to conserve battery life.

29. Infrared Transmitter Direct the remote control toward the remote sensor on the projector cabinet.

1-10

Digital Projection MERCURY 5000HD 1. Introduction

Remote Control Precautions

• The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the main unit, or when there is an obstacle in the path.

• When remote control buttons are pressed and held, projector’s function keys may not operate.

• Do not subject to strong shock.

• Do not allow water or other liquid to splash on the remote control. If the remote control gets wet, wipe it dry immediately.

• Avoid exposure to heat and steam.

• Remove the batteries from the remote control when the remote control is not going to be used for a long period.

Remote Control Battery Installation

Installing the Remote Control Batteries When it comes time to replace the batteries, two "AA" type will be required.

1. Press and open the cover.

Operating Range for Wireless Remote Control

The infrared signal operates by line-of-sight up to a distance of approximately 7m (20 feet) and a 60 degree angle of the remote sensor. The projector will not function if there are objects between the remote sensor and the remote control or if strong light falls on the remote sensor. Weak batteries will also prevent the projector from operating properly.

Side View

Remote sensors on the projector cabinet

Remote

control

2. Align and insert the batteries according to the (+) and (-) indications inside the case.

3. Replace the cover.

Remote

control

NOTE: Not to scale. NOTE: You cannot operate the projector using the remote control if:

• The remote control ID is not set to [None].

• The remote ID is not the same as the projector ID. See page 7-2 for setting remote ID and projector ID.

1-11

1. Introduction Digital Projection MERCURY 5000HD

Using the Remote Control in Wired Operation

Connect one end of the supplied remote cable to the REMOTE 2 IN mini jack and the other end to the remote jack on the remote control.

NOTE: Do not use this jack for anything other than intended use. Connecting the wired remote control to the SC. TRIGGER Mini Jack causes damage to the remote control.

REMOTE 2

Remote cable (supplied)

1-12

Installation

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Setting Up Your Projector ........................ 2-2

Screen Size and Projection Distance .......................................................... 2-2

Lens Shift Adjustable Range ................... 2-4

Optional Lens Installation ....................... 2-5

Making Connections ................................ 2-6

Connecting Your PC or Macintosh ............................................................... 2-6

To connect Scart Output ................................................................................ 2-7

Connecting an External Monitor ................................................................... 2-7

Connecting Your DVD Player ......................................................................... 2-8

Connecting Your VCR or Laser Disc Player ............................................... 2-9

Connecting to a Network ............................................................................. 2-10

Connecting the Supplied Power Cable .................................................... 2-11

2. Installation Digital Projection MERCURY 5000HD

This chapter describes how to set up your projector and how to connect video and audio sources.

Setting Up Your Projector

Your Projector is simple to set up and use. But before you get started, you must first:

1. Determine the image size

2. Set up a screen or select a non-glossy white wall onto which you can project your image.

3. Install the optional lens to the projector.

Screen Sizes

Height

Screen size (Diagonal)

Width

Formulas: Screen width W (m)= Screen size x 0.87 x 0.0254

Screen height H (m)= Screen size x 0.49 x 0.0254 Screen width W (inch)= Screen size x 0.87 Screen height H (inch)= Screen size x 0.45

4. Connect the supplied power cable.

5. Set up the projector.

6. Connect a PC, VCR, DVD player, or other equipment.

7. Make settings or adjustments on the projector.

Examples of Screen Sizes (in HD (16x9) format)

Screen size (D) Width (W) Height (H)

inches m inches m inches

60 1.3 52 0.7 29 67 1.5 58 0.8 33 72 1.6 63 0.9 35 80 1.8 70 1.0 39 84 1.9 73 1.0 41

90 2.0 78 1.1 44 100 2.2 87 1.2 49 120 2.7 105 1.5 59 150 3.3 131 1.9 74 180 4.0 157 2.2 88 200 4.4 174 2.5 98 210 4.6 183 2.6 103 240 5.3 209 3.0 118 250 5.5 218 3.1 123 270 6.0 235 3.4 132 300 6.6 261 3.7 147 400 8.9 349 5.0 196

Table of Throw Distances and Screen Sizes for Optional Fixed Lenses

NOTE: applicable to XGA and all wide-screen formats that use the full width of the DMD™.

NOTE: Actual throw distances may vary from those shown in the table below by up to +/-5%.

Screen

size

(D)

(inches)

60 67 72 80 84

90 100 120 150 180 200 210 240 250 270 300 400

fixed

(001-734)

0.64 : 1 m)(inches)

(

1.0

1.1

1.2

1.3

1.4

1.6

1.8

2.3

----

39 43 46 50 52 56 61 73 89

----

fixed

(001-735)

0.96 : 1

(m)

(inches)

1.4

1.5

1.6

1.8

1.9

2.0

2.2

2.7

105

3.3

130

3.9

155

4.4

172

4.6

180

5.2

205

5.4

214

5.8

230

6.5

255

8.6

339

2-2

Digital Projection MERCURY 5000HD 2. Installation

Table of Throw Distances and Screen Sizes for Optional Zoom Lenses

NOTE: applicable to all wide-screen formats that use the full width of the DMD™.

NOTE: Actual throw distances may vary from those shown in the table below by up to +/-5%.

(m)

2.0 2.4

2.2 2.7

2.3 2.9

2.6 3.2

2.7 3.4

2.9 3.6

3.2 4.0

3.9 4.8

4.8 6.0

5.8 7.2

6.4 8.0

6.7 8.4

7.7 9.6

8.0 10.0

---- ----

zoom

(001-737)

1.44 - 1.8 : 1 (inches)

77 96

86 107

92 115

102 127

107 133

11 5 143

127 159

152 190

190 237

228 284

253 315

265 331

303 378

315 394

---- ----

(m)

3.2 4.8

3.6 5.4

3.9 5.8

4.3 6.4

4.5 6.7

4.8 7.2

5.4 8.0

6.4 9.6

8.0 12.0

9.6 14.4

zoom

(001-739)

(inches)

127 190 142 212 152 228 169 253 178 265 190 284 21 1 316 253 378 316 473 378 567 420 629 441 661 504 755 525 786 567 849 629 943

---- ----

4.8 7.5

5.4 8.4

5.8 9.0

6.4 10.0

6.7 10.5

7.2 11.2

8.0 12.5

9.6 14.9

12.0 18.7

14.4 22.4

16.0 24.8

16.8 26.1

19.2 29.8

---- ----

zoom

(001-738)

1.8 - 2.4 : 1 2.4 - 3.6 : 1 3.6 - 5.6 : 1

(m)

2.4 3.2

2.7 3.6

2.9 3.9

3.2 4.3

3.4 4.5

3.6 4.8

4.0 5.4

4.8 6.4

6.0 8.0

7.2 9.6

8.0 10.7

8.4 11.2

9.6 12.8

10.0 13.3

10.8 14.4

12.0 16.0

16.0 21.3

(inches)

96 127

107 142

11 5 152

127 169

134 178

143 190

159 211

190 253

237 316

284 378

316 420

331 441

378 504

394 525

425 567

473 629

629 839

10.7 16.0

11. 2 16.8

12.8 19.2

13.3 20.0

14.4 21.6

16.0 24.0

---- ----

(001-740)

(m)

zoom

(inches)

190 295

212 329

228 354

253 393

266 412

285 441

316 490

379 588

473 734

567 881

630 978

661 1027

755 1174

---- ----

Screen

size

(D)

(inches)

60 67 72 80 84

90 100 120 150 180 200 210 240 250 270 300 400

(001-736)

1.2 - 1.44 : 1

(m)

1.7 2.0

1.9 2.2

2.0 2.4

2.2 2.6

2.3 2.8

2.5 3.0

2.7 3.3

3.3 3.9

4.1 4.9

4.9 5.8

5.4 6.5

---- ----

zoom

108 129 129 154 160 192 192 229 213 255

(inches)

66 79

74 88

79 94

87 104

91 109

98 116

---- ----

For screen sizes between 60" and 400" not indicated on the tables, use the formula below:

Throw Distance (distance from front of casing to screen) = [Screen Width (W) x Throw Ratio (magnification)] +/- [ extension]

(where [extension] = distance between front of casing and end of lens)

Example: Throw Distance for 2.5m wide screen using zoom lens 001-736 set to 1.3 : 1

Throw Distance = 2.5m x 1.3 = 3.25m + .088m = 3.34m

= 98in x 1.3 = 127in + 3.5in = 130.5in

Lens extensions and useable ranges are as follows:

magnification extension useable range

Fixed lens 001-734 0.64 : 1 142mm (5.6in) 1.0m - 2.3m (3ft 3in - 7ft 5in)

Fixed lens 001-735 0.96 : 1 110mm (4.3in) 1.4m - 8.6m (4ft 7in - 28ft 3in)

Zoom lens 001-736 1.2 : 1 88mm (3.5in) 1.7m - 5.4m (5ft 6in - 17ft 9in)

1.44 : 1 2.0m - 6.5m (6ft 7in - 21ft 3in)

Zoom lens 001-737 1.44 : 1 43mm (1.7in) 2.0m - 8.0m (6ft 5in - 26ft 3in)

1.8 : 1 2.4m - 10.0m (8ft - 32ft 10in)

Zoom lens 001-738 1.8 : 1 47mm (1.9in) 2.4m - 16.0m (8ft - 52ft)

2.4 : 1 3.2m - 21.3m (11ft - 70ft)

Zoom lens 001-739 2.4 : 1 47mm (1.9in) 3.2m - 16.0m (11ft - 52ft)

3.6 : 1 4.8m - 24.0m (16ft - 79ft)

Zoom lens 001-740 3.6 : 1 54mm (2.1in) 4.8m - 19.2m (16ft - 63ft)

5.6 : 1 7.5m - 29.8m (25ft - 98ft)

2-3

2. Installation Digital Projection MERCURY 5000HD

Lens Shift Adjustable Range

The diagram shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normal projection position as a starting point.

Maximum Possible Range (for zoom lenses only: fixed lens cannot be shifted): Up: 0.5 H where H: height of projected image Down: 0.16 H Right: 0.1 W where W: width of projected image Left: 0.1 W

NOTE: If lens is shifted in two directions combined, maximum range in both directions cannot be obtained due to circular shape of lens. (example: shift up and right - see dotted box in diagram below.)

NOTE: zoom lenses only: fixed lenses cannot be shifted without losing the corners of the image

Desktop Mounting

Normal projection position

Ceiling Mounting

WARNING

* Installing the projector on the ceiling must be done by a qualified

technician.

• Tilting the projector from side to side by more than 12° from level will reduce lamp life (see page iv).

• Only use your projector on a solid, level surface. If the projector falls, you could be injured and the projector severely damaged.

• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 32°F (0°C) and 95°F (35°C).

• Do not expose the projector to moisture, dust, or smoke. This will reduce the quality of the image.

• Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the projector.

2-4

Digital Projection MERCURY 5000HD 2. Installation

Optional Lens Installation

This section describes how to install the lens.

Before installation

* Determine the optional lens to be used to obtain a desired projection distance. There are six optional lenses available:

0.64 : 1 fixed part no. 001-734

0.96 : 1 fixed part no. 001-735

1.2 - 1.44 : 1 zoom part no. 001-736

1.44 - 1.8 : 1 zoom part no. 001-737

1.8 - 2.4 : 1 zoom part no. 001-738

2.4 - 3.6 : 1 zoom part no. 001-739

3.6 - 5.6 zoom part no. 001-740

* Press the power button (ON/STAND BY) on the projector or POWER OFF button on the remote control for a minimum of two seconds to turn

off the power, wait 90 seconds for the cooling fan to stop, then disconnect the power cable.

Check that the projector has cooled off sufficiently before proceeding.

CAUTION

* The projector and lens contain high-precision parts. Do not induce shock to the projector or the lens.

* Do not touch the lens surface. Doing so can degrade the optical performance.

Preparation: Tools needed for installation:

A cross head screwdriver.

NOTE: It is possble that the ‘Lens Shift’ feature (described on the previous page and in Section 3. Projecting an Image) may have used to move the lens mount to the far right side, making installation difficult. If this is the case, then turn the projector back on again and use the Position buttons to shift the lens back towards the mid-position. When this has been done, turn the projector off as decribed above, before continuing.

1. Remove the rear lens cover, but leave the front cover on to protect the lens surface during installation.

2. Insert the lens into the lens mount with the connector to the right, taking care to line up the locating pin on the lens with the locating hole above the opening. Push the lens in firmly to engage the connector.

locating hole

3. Secure the lens using the three cross-head screws.

NOTE. Remove the lens cover before use

fixing screws

2-5

2. Installation Digital Projection MERCURY 5000HD

Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software. * If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.

When Viewing a DVI Digital Signal:

To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC or projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC. Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC. Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected and then reconnected, an image may not be correctly displayed. Should this happen, restart your PC.

NOTE:

• Use the DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should be within 5 m (196") long.

• The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).

Connecting your PC or Macintosh Computer

Audio cable (not supplied)

RGB signal cable (not supplied) To mini D-Sub 15-pin connector on the projector.

IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type)

Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image for an impressive presentation. To connect to a PC or Macintosh, simply:

1. Turn off the power to your projector and computer.

2. Use a commercially available signal cable to connect your PC or Macintosh to the projector.

3. Turn on the projector and the computer.

4. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector.

BNC x 5 cable (not supplied)

Audio cable (not supplied)

IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)

DVI-D cable with ferrite core (not supplied)

Audio cable (not supplied)

NOTE: For older Macintosh, use a commercially available pin adapter (not supplied) to connect to your Mac's video port.

Connecting to RGB 1 IN connectors (BNC)

Use a BNC25 cable (not supplied) to connect your PC and the RGB 1 IN connectors on your projector.

Connecting to RGB2 IN connector (D-Sub 15 Pin)

Use an RGB signal cable (not supplied) to connect your PC and the RGB2 IN connector on your projector.

Connecting Your PC with a DVI Connector

Use a DVI-D signal cable (not supplied) to connect a DVI connector of your PC to the projector.

2-6

Digital Projection MERCURY 5000HD 2. Installation

To connect SCART output (RGB)

Before connections: An exclusive SCART adapter (ADPSC1) and a commercially available SCART cable are required for this connection.

NOTE:

• Audio signal is not available for this connection.

• The RGB 1 IN connector does not support Plug & Play.

Video equipment such as DVD player

Projector

1. Turn off the power to the projector and your video equipment.

2. Use the ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB 2 input of your projector and a SCART output (RGB) of your video equipment.

3. Turn on the power to the projector and your video equipment.

4. Use the RGB 2 button on the remote control to select the RGB 2 input.

5. Press the MENU button on the remote control to display the menu.

6. From the Advanced menu, select [Projector Options] [Page 3] ∅ [Signal Select RGB2] ∅ [Scart]. SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-connector.

∅

[Setup]

∅

Commercially available SCART cable

Female

Connecting an External Monitor

RGB signal cable (not supplied) To mini D-Sub 15-pin connector on the projector.

ADP-SC1

To RGB 2 IN

NOTE: The ADP-SC1 SCART adapter is obtainable from your Digital Projection dealer. Contact your Digital Projection dealer for more information.

Audio cable (not supplied)

You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog image you're projecting. To do so:

1. Turn off the power to your projector, monitor and computer.

2. Use a 15-pin cable to connect your monitor to the RGB OUT (Mini DSub 15 pin) connector on your projector.

3. Turn on the projector, monitor and the computer.

RGB signal cable (not supplied) To mini D-Sub 15-pin connector on the projector.

NOTE:

• The RGB OUT connector outputs RGB signal during idle mode (See page 8-15). When the projector goes into idle mode, the image on an external monitor disappears for a moment. Note that the RGB OUT connector will not output RGB signal during Standby mode.

• When the projector is in the Idle mode, the image may not be correctly displayed while the cooling fans are running immediately after turning on or off the power. Note that the RGB OUT connector will not output RGB signal during Standby mode.

• Daisy chain connection is not possible.

2-7

2. Installation Digital Projection MERCURY 5000HD

Connecting Your DVD Player

Optional 15-pin-to-RCA (female) x 3 cable (ADP-CV1)

RCA(female)-to-BNC(male) adapter (not supplied)

Component video RCA x 3 cable (not supplied)

Audio cable (not supplied)

DVD player

You can connect your projector to a DVD player with component output or Video output. To do so, simply:

1. Turn off the power to your projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable (RCAX3) and the optional 15-pin-to-RCA (female) x 3 cable to connect your DVD player to the RGB 1 IN or 2 IN connector on the projector.

For a DVD player without a component video (Y,Cb,Cr) output, use an

Audio Equipment

Audio cable (not supplied)

S-Video cable (not supplied) to connect an S-Video output of the DVD player to the S-Video input of the projector. Use an appropriate type of audio cable (not supplied) to connect the desired type of audio from your DVD player to your audio equipment.

3. Turn on the projector and DVD player.

NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements,

2-8

Digital Projection MERCURY 5000HD 2. Installation

Connecting Your VCR or Laser Disc Player

Audio cable (not supplied)

VCR/ Laser disc player

Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your projector. To make these connections, simply:

1. Turn off the power to the projector and VCR, laser disc player or document camera.

2. Connect one end of an RCA cable (not supplied) to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your projector (an RCA to BNC adapter is necessary). Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.

3. Turn on the projector and the VCR or laser disc player.

Video cable (not supplied)

S-video cable (not supplied)

Audio equipment

Audio cable (not supplied)

NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements.

NOTE: An image may not be displayed correctly when a Video or SVideo source is played back in fast-forward or fast-rewind via a scan converter.

2-9

2. Installation Digital Projection MERCURY 5000HD

Connecting to a Network

With the LAN connection, you can control the projector over the network using a computer to switch the unit on/off, select the input and others.

* To control the projector over the network using a computer, use the Dynamic Image Utility 2.0 contained on the User Supportware CD-ROM or

the HTTP Server feature.

* With the Image Express Utility 1.0 contained on the supplied User Supportware CD-ROM, you can project your PC screen image to the

projector over the network.

* With a use of the supplied User Supportware CD-ROM and the optional wireless LAN card (SWL-2100-N*), you can control the projector

wirelessly or send your PC screen image to the projector over the network using a computer.

Example of LAN connection

Server

Hub

LAN cable (not supplied)

Using the HTTP Server function

1. Configure your LAN settings such as IP address on the projector. (See “LAN Mode” on page 8-19)

2. Start the Web browser on the computer connected to the network and execute HTTP server functions. (See “Operation Using an HTTP Browser” on page 10-11)

Using the User Supportware

1. Configure your LAN settings such as IP address on the projector. (See “LAN Mode” on page 8-19)

2. Install the software contained on the User Supportware CD-ROM into the computer connected to the network. See “6 Using the Projector in a Network” on page 6-1.

2-10

+ 80 hidden pages