Digital Projection HIGHlite LASER II User Manual
HIGHlite Laser II 3D Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
Rev A August 2016
118-089A
Digital Projection HIGHlite Laser II 3D Series
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Notes
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2016 Digital Projection Ltd. All rights reserved.
Rev A August 2016
page i
Digital Projection HIGHlite Laser II 3D Series
상호명/제조자: 델타일렉트로닉스㈜
제조공장/제조국가: 델타 비디오 디스플레이
시스템 (우장) 리미티드
제조시기 : 년 월
116-330
S/N:
M/F Date:
Laser Information
RISK GROUP 2
Possibly hazardous optical radiation emitted
Do not stare at operating lamp.
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
CAUTION
Ce produit peut émettre des rayonnements
from this product.
Ne pas fixer la lampe en fonctionnement.
May be harmful to the eyes.
ATTENTION
optiques dangereux.
Peut être nocif pour les yeux.
Notes
Rev A August 2016
page ii
Digital Projection HIGHlite Laser II 3D Series
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Support for most 3D formats.
• HDBaseT
• 3G-SDI with loop-through.
• Edge Blend.
• Blanking control for custom input window sizing.
• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the side of the projector. Record it here:
®
for transmission of uncompressed High Denition Video up to 100 m from the source.
Notes
Rev A August 2016
page iii
Digital Projection HIGHlite Laser II 3D Series
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
Voltage selection ................................................................................... 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel ......................................................................................... 6
REMOTE CONTROL ....................................................................... 7
Infrared reception ................................................................................ 10
POSITIONING THE SCREEN AND PROJECTOR ........................... 11
Roll and pitch ...................................................................................... 12
CHANGING THE LENS ................................................................. 13
The lens hood ..................................................................................... 13
Inserting a new lens ............................................................................ 14
Removing the lens .............................................................................. 15
CHANGING THE FILTERS ............................................................ 16
OPERATING THE PROJECTOR .................................................... 17
Switching the projector on ................................................................... 17
Switching the projector off ................................................................... 17
Selecting an input signal ..................................................................... 18
Selecting a test pattern ....................................................................... 18
Adjusting the lens ................................................................................ 19
Adjusting the image............................................................................. 19
CONNECTION GUIDE ............................................................................21
SIGNAL INPUTS .......................................................................... 23
Digital inputs and outputs .................................................................... 23
Analog inputs and outputs................................................................... 24
EDID on the HDMI, DisplayPort and VGA inputs ................................ 25
Using HDMI/DisplayPort switchers with the projector ......................... 25
3D connections ................................................................................... 26
3D sources up to 60Hz requiring frame doubling and left/right interleaving .......... 26
Frame sequential 3D sources up to 120Hz ................................................. 26
Dual Pipe 3D ...................................................................................... 26
3D Sync............................................................................................... 27
3D Sync in ......................................................................................... 27
3D Sync out ....................................................................................... 27
CONTROL CONNECTIONS ........................................................... 28
LAN connection examples .................................................................. 29
RS232 connection example ................................................................ 30
Rev A August 2016
page iv
Digital Projection HIGHlite Laser II 3D Series
CONTENTS (continued)
OPERATING GUIDE ................................................................................31
USING THE MENUS ..................................................................... 33
Opening the OSD ................................................................................ 33
Opening a menu.................................................................................. 33
Exiting menus and closing the OSD.................................................... 33
Inside a menu...................................................................................... 34
Accessing sub-menus ........................................................................... 34
Executing commands............................................................................ 34
Editing projector settings ..................................................................... 35
Using a slider to set a value .................................................................... 35
Editing numeric values .......................................................................... 35
USING THE PROJECTOR ............................................................. 36
Main menu .......................................................................................... 36
Lens menu .......................................................................................... 37
Lens Control ....................................................................................... 37
Lens Memory ...................................................................................... 38
Image menu ........................................................................................ 39
Noise Reduction .................................................................................. 40
Position and Phase .............................................................................. 40
Color menu.......................................................................................... 41
Color Space ....................................................................................... 41
Color Mode ........................................................................................ 42
Geometry menu .................................................................................. 47
Aspect Ratio ....................................................................................... 47
Digital Zoom & Shift .............................................................................. 49
Overscan ........................................................................................... 50
Blanking ............................................................................................ 51
Keystone ........................................................................................... 52
4 Corners .......................................................................................... 54
Rotation ............................................................................................ 55
Pincushion / Barrel ............................................................................... 56
Edge Blend menu................................................................................ 57
Blend Width........................................................................................ 58
Black Level Uplift ................................................................................. 59
3D menu.............................................................................................. 60
3D types ............................................................................................ 61
Some 3D settings explained ................................................................... 62
Frame rate multiplication in 3D images ...................................................... 63
Laser menu ......................................................................................... 64
Setup menu ......................................................................................... 65
ColorMax Setting ................................................................................. 67
Power On/Off ...................................................................................... 68
Clock Adjust ....................................................................................... 69
OSD Settings ...................................................................................... 70
Memory ............................................................................................. 70
Network menu ..................................................................................... 71
PIP menu ............................................................................................ 72
Information menu ................................................................................ 73
Signal Format ..................................................................................... 73
System Status .................................................................................... 74
Thermal Status.................................................................................... 74
Factory Reset ..................................................................................... 75
POSSIBLE COMBINATIONS OF SETTINGS .................................. 76
Rev A August 2016
page v
Digital Projection HIGHlite Laser II 3D Series
CONTENTS (continued)
REFERENCE GUIDE ................................................................................77
THE DMD™ .................................................................................. 80
CHOOSING A LENS ..................................................................... 82
Basic calculation ................................................................................. 83
Basic calculation example ................................................................... 84
Full lens calculation ............................................................................. 85
Introducing TRC .................................................................................. 85
Calculating TRC .................................................................................. 86
Calculating the throw ratio with TRC ......................................................... 87
Full lens calculation example .............................................................. 88
SCREEN REQUIREMENTS ........................................................... 89
Fitting the image to the DMD™ ........................................................... 89
WUXGA images displayed full width ......................................................... 89
WUXGA images displayed with a height of 1080 pixels .................................. 90
WUXGA images displayed full height ........................................................ 91
Diagonal screen sizes ......................................................................... 92
Fitting the image to the screen ............................................................ 93
Positioning the screen and projector ................................................... 94
POSITIONING THE IMAGE ........................................................... 95
Maximum offset range ......................................................................... 97
2:3:3:2 (advanced) pulldown ................................................................. 103
APPENDIX A: LENS PART NUMBERS ........................................ 104
APPENDIX B: LENS CHARTS .................................................... 105
How to use the lens charts ................................................................... 105
TRC values applied in the charts ........................................................... 106
Fixed lenses - full DMD™ width images ................................................... 107
Zoom lenses - full DMD™ width images .................................................. 108
Fixed lenses - 1.25:1 images ................................................................ 109
Zoom lenses - 1.25:1 images ................................................................ 110
Fixed lenses - 1.33:1 images .................................................................111
Zoom lenses - 1.33:1 images ................................................................ 112
APPENDIX C: SUPPORTED SIGNAL INPUT MODES ...................113
2D formats......................................................................................... 113
3D formats......................................................................................... 115
APPENDIX D: MENU MAP ...........................................................117
ASPECT RATIOS EXPLAINED ...................................................... 98
Aspect ratio examples ......................................................................... 99
FRAME RATES AND PULLDOWNS EXPLAINED ......................... 101
Interlaced and progressive scan ....................................................... 101
Frame rates of image sources .......................................................... 101
Pulldowns - conversion into destination formats ............................... 102
2:3 (normal) pulldown ......................................................................... 102
Rev A August 2016
page vi
Digital Projection HIGHlite Laser II 3D Series
CONTENTS (continued)
APPENDIX E: WIRING DETAILS ................................................. 128
Signal inputs and outputs .................................................................. 128
VGA ............................................................................................... 128
HDMI 1 and 2 ................................................................................... 129
DisplayPort ...................................................................................... 130
3G-SDI In, 3G-SDI Out ........................................................................ 131
COMPONENT .................................................................................. 131
Control connections .......................................................................... 132
LAN ............................................................................................... 132
RS232 ............................................................................................ 132
Trigger 1 & Trigger 2 ........................................................................... 133
IR input ........................................................................................... 133
3D Sync IN and 3D Sync OUT .............................................................. 133
APPENDIX F: GLOSSARY OF TERMS ........................................ 134
TECHNICAL SPECIFICATIONS .................................................. 145
Models............................................................................................... 145
Inputs and outputs............................................................................. 146
Bandwidth ......................................................................................... 146
Remote control and keypad .............................................................. 146
Automation control ............................................................................ 146
Color temperature ............................................................................. 146
Lenses............................................................................................... 147
Lens mount ....................................................................................... 147
Mechanical mounting ........................................................................ 147
Orientation......................................................................................... 147
Electrical and physical specications ................................................ 148
Safety & EMC regulations ................................................................. 148
Rev A August 2016
page vii
HIGHlite Laser II 3D Series
High Brightness Digital Video Projector
4
INSTALLATION AND QUICK-START GUIDE
Rev A August 2016
Digital Projection HIGHlite Laser II 3D Series
IN THIS GUIDE
IN THIS GUIDE
What’s In The Box? ............................................................................................. 3
Connecting The Power Supply ........................................................................ 4
Voltage selection ......................................................................................................... 4
Projector Overview ............................................................................................. 5
Front and rear views ...................................................................................................5
Control Panel ........................................................................................................ 6
Remote Control .................................................................................................... 7
Infrared reception ......................................................................................................10
Positioning The Screen And Projector ....................................................... 11
Roll and pitch ............................................................................................................12
Changing The Lens ........................................................................................... 13
The lens hood ............................................................................................................13
Inserting a new lens ..................................................................................................14
Removing the lens ....................................................................................................15
Changing The Filters ........................................................................................ 16
Operating The Projector ................................................................................. 17
Switching the projector on .......................................................................................17
Switching the projector off .......................................................................................17
Selecting an input signal ..........................................................................................18
Selecting a test pattern .............................................................................................18
Adjusting the lens .....................................................................................................19
Adjusting the image ..................................................................................................19
Installation and Quick-Start Guide
Rev A August 2016
Digital Projection HIGHlite Laser II 3D Series
PicMute
OFF
ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
A B C D
USERPRESET
WHAT’S IN THE BOX?
What’s In The Box?
Remote control
(116-088)
2x AAA batteries
Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
Only one remote will be supplied
with the projector. For more
information, see Remote Control
further in this guide.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
Projector
The projector is shipped without a
lens.
Do not use the short lens hood
with the 4.34 - 6.76 : 1 zoom lens.
User Manual on disc
(115-759)
Power cable, United Kingdom
(112-000)
Installation and Quick-Start Guide
Important Information (114-914)
HDMI cable
For further information about using
the right lens and hood, see The
lens hood further in this guide.
Power cable, Europe
(112-001)
Power cable, North America
(112-002)
Power cable, China
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Rev A August 2016
page 3
Digital Projection HIGHlite Laser II 3D Series
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Lift the cable lock up, push the mains connector in rmly and
push the lock down to secure the cable.
AC mains inlet with cable lock
1
Voltage selection
The VOLTAGE SELECT switch must be set to match the power supply you are using:
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
1
and avoid sharp bends. Do not
use a damaged power cable.
Voltage of power supply used Position of VOLTAGE SELECT switch
AC100V outlet
AC200V (single phase) outlet
Installation and Quick-Start Guide
Rev A August 2016
page 4
Digital Projection HIGHlite Laser II 3D Series
PROJECTOR OVERVIEW
Projector Overview
Front and rear views
Control panel
1
Connection panel
2
Air outlet
3
Lens hood
4
Front infrared window
5
Power switch and power connection
6
Air outlet
7
Rear infrared window
8
Air inlet
9
Adjustable feet
10
4 5
7 8
1
Front view
2
3
Notes
Do not use the short lens hood
with the 4.34 - 6.76 : 1 zoom lens.
For further information about using
the right lens and hood, see The
lens hood further in this guide.
6
9
Installation and Quick-Start Guide
10
Rear view
Rev A August 2016
page 5
Digital Projection HIGHlite Laser II 3D Series
CONTROL PANEL
Control Panel
1
ON indicator (blue)
Behavior Meaning
Off The projector is switched off.
On The projector is switched ON.
Flashing The projector is warming up or cooling down.
2
ERROR indicator (red)
Behavior Meaning
Flash once, then pause Laser failure.
Flash twice, then pause Cover open.
Flash three times, then pause Fan failure.
Flash four times, then pause Over temperature.
On System error.
3
STANDBY indicator (green)
Behavior Meaning
On The projector is in STANDBY mode.
Flashing The projector is in STANDBY mode.
It can be switched on with a network command.
MENU button
4
Access the projector OSD (on-screen display).
5
Navigation (arrow buttons and ENTER)
Navigate the OSD and edit settings with the arrows, conrm choice with ENTER.
6
INPUT button
Select input source.
1
ERROR STANDBY
2
3
4
MENU
5
6
INPUT
7
OUT IN
8
OUT IN
Notes
10
11
EXIT
12
SHIFT
FOCUS
ZOOM
Focus IN / OUT
7
Adjust focus.
Zoom IN / OUT
8
Adjust zoom.
Shutter CLOSE / OPEN
9
Open and close the shutter.
10
POWER button
Switch the projector on and off (in STANDBY mode)
11
EXIT button
Close the OSD.
12
SHIFT button
Press and hold this button, then press the arrow buttons to move the lens.
Installation and Quick-Start Guide
9
CLOSE
SHUTTER
OPEN
Rev A August 2016
page 6
Digital Projection HIGHlite Laser II 3D Series
REMOTE CONTROL
Remote Control
1
Power ON / OFF
Turns power on and off.
2
Pic Mute ON / OFF
Shows and hides the projected image.
When OFF, the light source is completely switched off and the screen is black.
2
OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD
during projection.
4
MENU
Access the OSD. If the OSD is open, press this button to go back to the previous menu.
5
Navigation (arrows and OK)
Navigate through the menus with the arrows, conrm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11
below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6
EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
7
FREEZE
Freeze the current frame.
8
DEFAULT
When editing a parameter, press this button to restore the default value.
9
INFO
Access information about the projector.
10
RE-SYNC
Re-synchronise with the current input signal.
Notes
OFF ON
1
Pic Mute
2
3
4
5
6
7
OFF
OFF
MENU
EXIT INFO
FREEZE
FOCUS ZOOM
IN
OUT
USER PRESET
A B C D
HDMI2 DVI
HDMI1
21 3
BRI
CON GAMMA
DISPLAYPORT
HD-T 3GSDI
4 5 6
R G B ALL
VGA COMP1 COMP2
7 8 9 0
3D EYE PIP SWAP
ON
OSD
ON
DEFAULT
8
OK
9
RE-SYNC
10
LENS
IN
SHIFT
OUT
ALT
ALT
ADDR
TEST
continues on next page...
Installation and Quick-Start Guide
Rev A August 2016
page 7
MENU
EXIT INFO
OK
OSD
OFF
ON
DEFAULT
Digital Projection HIGHlite Laser II 3D Series
11
LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12
USER PRESET A, B, C, D
Load user presets.
13
ALT
14
Press and hold this button to access alternative functions for all
buttons with a green label.
DVI / GAMMA / numeric input 3
Select the DVI input.
Use with ALT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
15
HDMI 2 / CON / numeric input 2
Select the HDMI 2 input.
Use with ALT to bring up the Contrast control, then adjust the value
with the LEFT and RIGHT arrow buttons.
16
HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with ALT to bring up the Brightness control, then adjust the
value with the LEFT and RIGHT arrow buttons.
17
TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard,
CrossHatch, V Burst, H Burst, ColorBar...
When PIP mode is on, use this button with ALT to swap the main and
sub images.
REMOTE CONTROL
FREEZE
FOCUS ZOOM
11
12
IN
OUT
A B C D
HDMI1
BRI
DISPLAYPORT
4 5 6
R G B ALL
VGA COMP1 COMP2
7 8 9 0
3D EYE PIP SWAP
LENS
SHIFT
USER PRESET
HDMI2 DVI
21 3
CON GAMMA
HD-T 3GSDI
RE-SYNC
IN
OUT
ALT
ALT
ADDR
TEST
Notes
For further information about
user presets, see Memory in the
Operating Guide.
13
14
15
16
17
continues on next page...
Installation and Quick-Start Guide
Remote control
Rev A August 2016
page 8
Pic Mute
OFF
ON
MENU
EXIT INFO
OK
LENS
FOCUS ZOOM
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
Digital Projection HIGHlite Laser II 3D Series
17
DISPLAYPORT / R / numeric input 4
18
HD-T / G / numeric input 5
Select DisplayPort input.
Select the HDBaseT input.
19
3GSDI / B / numeric input 6
Select the 3G-SDI input.
20
VGA / 3D / numeric input 7
Select the VGA input.
Use with ALT to toggle the 3D Format setting between Off and Auto.
21
COMP1 / EYE / numeric input 8
22
23
Select the Component 1 input.
Use with ALT to switch between left and right eye 3D dominance.
COMP2 / PIP / numeric input 9
Select the Component 2 input.
Use with ALT to switch on Picture In Picture (PIP) mode.
ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter
a two-digit address using the numeric input buttons. The indicator
will ash three times quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the
indicator ashes to conrm the change.
REMOTE CONTROL
OFF ON
Remote control top
IN
OUT
A B C D
HDMI1
BRI
DISPLAYPORT
17
18
19
20
21
22
4 5 6
R G B ALL
VGA COMP1 COMP2
7 8 9 0
3D EYE PIP SWAP
Pic Mute
OFF
OSD
SHIFT
USER PRESET
HDMI2 DVI
21 3
CON GAMMA
HD-T 3GSDI
Notes
ON
IN
OUT
ALT
ALT
ADDR
23
TEST
Installation and Quick-Start Guide
Remote control bottom
Rev A August 2016
page 9
Digital Projection HIGHlite Laser II 3D Series
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes
Installation and Quick-Start Guide
Rev A August 2016
page 10
Digital Projection HIGHlite Laser II 3D Series
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1
Four adjustable feet
2
Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into
the body of the projector.
1
2
1
2
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 50
cm (20 in) of space between the
ventilation outlets and any wall,
and 30 cm (12 in) on all other
sides.
Do not stack more than 3
projectors.
Installation and Quick-Start Guide
2
2
1
2
2
1
Rev A August 2016
page 11
Digital Projection HIGHlite Laser II 3D Series
POSITIONING THE SCREEN AND PROJECTOR
Roll and pitch
The projector can be operated in numerous positions.
It is not recommended to position the projector in portrait mode with inputs facing upward, as shown in the diagram.
30°
330°
1
360°
2
2
Notes
Roll
1
Positions to avoid: inputs side up
2
Recommended positions
Installation and Quick-Start Guide
Pitch
Rev A August 2016
page 12
Digital Projection HIGHlite Laser II 3D Series
CHANGING THE LENS
Changing The Lens
The lens hood
There are two types of lens hood, short and long.
The short lens hood is used with the following lenses:
Throw ratios Part number
0.77 : 1 xed lens 110-808
1.16 : 1 xed lens 110-809
1.45 - 1.74 : 1 zoom lens 110-803
1.74 - 2.17 : 1 zoom lens 112-878
2.17 - 2.90 : 1 zoom lens 113-852
2.90 - 4.34 : 1 zoom lens 110-806
The long lens hood must be used with the following long throw lens:
Throw ratios Part number
4.34 - 6.76 : 1 zoom lens 110-807
Projector with short lens hood tted
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
Do not use the short lens hood
with the 4.34 - 6.76 : 1 zoom lens.
The projector will not power on
without the lens and lens hood tted.
Installation and Quick-Start Guide
Projector with long lens hood tted
Rev A August 2016
page 13
Digital Projection HIGHlite Laser II 3D Series
CHANGING THE LENS
Inserting a new lens
1. Insert the lens into the lens aperture, making sure that the plug on the zoom drive
mechanism lines up with socket on the right of the lens aperture.
2. Rotate the lens clockwise until it clicks into place.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
Do not use the short lens hood
with the 4.34 - 6.76 : 1 zoom lens.
3. Secure the lens hood to the front of the projector with the screws.
Installation and Quick-Start Guide
The projector will not power on
without the lens and lens hood tted.
Rev A August 2016
page 14
Digital Projection HIGHlite Laser II 3D Series
CHANGING THE LENS
Removing the lens
1. Loosen the four screws securing the lens hood to the body of the projector.
Remove the lens hood.
2. Push down the lens holder tab.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
The projector will not power on
without the lens and lens hood tted.
3. Rotate the lens anti-clockwise.
4. Pull the lens forward to remove it from the lens aperture.
Installation and Quick-Start Guide
Rev A August 2016
page 15
Digital Projection HIGHlite Laser II 3D Series
CHANGING THE FILTERS
Changing The Filters
1. Remove the two screws 1 holding the lter cover.
2. Remove the lter cover 2.
3. Remove the old lter 3.
4. Place the new lter in the slot. Make sure the air ow arrow 4 points toward the projector, as shown in the illustration.
5. Replace the lter cover and tighten the screws.
Notes
Beforechangingthelters,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Whenchangingthelters,avoid
using excessive force as this may
damage the equipment.
In a normal environment the lters
should be changed every 2000
hours.
Installation and Quick-Start Guide
1
2
4
3
Rev A August 2016
page 16
Digital Projection HIGHlite Laser II 3D Series
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Ensure a lens is tted. Connect the power cable between the mains supply and the projector. (See Connecting the power supply
above.) Switch on at the switch next to the power connector.
2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following buttons:
• On the remote control, the ON button
• On the projector control panel, the POWER button.
The fans begin working, then the POWER indicator begins ashing green. When the ashing stops, the POWER and LIGHT indicators
both light steady green. The projector is switched on.
Switching the projector off
1. Press OFF on the remote control or POWER on the control panel, then press again to conrm your choice.
The POWER indicator on the control panel will start ashing amber, the system will go out and the cooling fans will run for a short time
until the POWER indicator goes stready red to indicate that the projector has entered STANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect
the power cable from the projector.
Notes
See also Connecting The Power
Supply earlier in this guide.
The self-test is running when all the
LEDs on the control panel are lit.
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
Installation and Quick-Start Guide
Rev A August 2016
page 17
Digital Projection HIGHlite Laser II 3D Series
OPERATING THE PROJECTOR
Selecting an input signal
1. Connect one or more image sources to the projector.
2. Select the input you want to display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/OK and then
select an input signal using the UP and DOWN arrow buttons. Press ENTER/OK to conrm your choice.
Selecting a test pattern
To display a test pattern:
• Press TEST on the remote control.
Change the test pattern using the LEFT and RIGHT arrow buttons.Test patterns are displayed in the following order:
White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst, H Burst, ColorBar, Screen Layout, Off
• Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu, then select a test pattern using the LEFT
and RIGHT arrow buttons.
After the nal test pattern, the projector exits test pattern mode and returns to the main image. To view test patterns again, you need to press
TEST again. If you wish to exit the test patterns before you reach the nal one,
• press TEST or EXIT at any time.
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Installation and Quick-Start Guide
Rev A August 2016
page 18
Digital Projection HIGHlite Laser II 3D Series
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. The setting operates in Zoom/Focus Adjustment and
Shift Adjustment mode.
Press ENTER/SELECT to switch between the two modes.
Remote control
Use the remote control to adjust zoom, focus and shift directly, without opening a menu:
• OK enters lens control, then switches between Zoom/Focus Adjustment and Shift Adjustment.
• EXIT exits lens control and opens the Lens menu.
• MENU exits lens control and returns to the main image.
• The arrow buttons adjust zoom, focus and shift as indicated on the screen.
Adjusting the image
Orientation
• This can be set from the Setup menu.
Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Auto-front.
Notes
When adjusting focus and zoom,
you may nd it useful to display
the CrossHatch test pattern: press
TEST on the remote control and
navigate through the list of patterns
using the LEFT and RIGHT
arrow buttons.
For full details of how to adjust
the lens using the remote control,
see Remote Control earlier in this
guide.
Setup menu
Keystone
• This can be set from the Geometry menu.
Picture
• Settings such as Gamma, Brightness, Contrast, Saturation, Hue and Sharpness can be set from the Image menu.
Installation and Quick-Start Guide
Geometry menu
Image menu
Rev A August 2016
page 19
Digital Projection HIGHlite Laser II 3D Series
This page is intentionally left blank.
Installation and Quick-Start Guide
HIGHlite Laser II 3D Series
High Brightness Digital Video Projector
4
CONNECTION GUIDE
Rev A August 2016
Digital Projection HIGHlite Laser II 3D Series
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ....................................................................................................... 23
Digital inputs and outputs ........................................................................................23
Analog inputs and outputs .......................................................................................24
EDID on the HDMI, DisplayPort and VGA inputs ....................................................25
Using HDMI/DisplayPort switchers with the projector ..........................................25
3D connections .........................................................................................................26
3D sources up to 60Hz requiring frame doubling and left/right interleaving ...................26
Frame sequential 3D sources up to 120Hz .....................................................................26
Dual Pipe 3D ...................................................................................................................26
3D Sync ......................................................................................................................27
3D Sync in .......................................................................................................................27
3D Sync out ....................................................................................................................27
Control Connections ........................................................................................ 28
LAN connection examples .......................................................................................29
RS232 connection example ......................................................................................30
Connection Guide
Rev A August 2016
Loading...