Page 1
HIGHlite 6000
High Brightness Digital Video Projector
16:9 widescreen display
Rev A October 2010
111-339A
Page 2
Digital Projection HIGHlite 6000 User Manual
Page 3
Digital Projection HIGHlite 6000 User Manual
Declaration of Conformity
Directives covered by this Declaration
2004/108/EC Electromagnetic Compatibility Directive.
2006/95/EC Low Voltage Equipment Directive.
Products covered by this Declaration
Largescreenvideoprojectortype TheCEmarkwasfirstappliedin:
HIGHlite 6000 September 2010
Basis on which Conformity is being declared
TheproductsidentifiedabovecomplywiththeprotectionrequirementsoftheaboveEUdirectives,andthe
manufacturer has applied the following standards.
EN 55022:1998 Limits and Methods of Measurement of Radio Disturbance Characteristics of Information
Technology Equipment.
EN 55024:1998 Limits and Methods of Measurement of Immunity Characteristics of Information Technology
Equipment.
EN609501:2001SpecificationforSafetyofInformationTechnologyEquipment,includingElectricalBusiness
equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage
directive has been compiled by the signatory below and is available for inspection by the relevant enforcement
authorities.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 20 September 2010
Attention!
Theattentionofthespecifier,purchaser,installer,oruserisdrawntospecialmeasuresandlimitationstousewhich
must be observed when these products are taken into service to maintain compliance with the above directives.
Details of these special measures are available on request, and are also contained in the product manuals.
Page 4
Digital Projection HIGHlite 6000 User Manual
Page 5
Important Information
Please read this user manual carefully before using the projector, and keep
the manual handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in this guide
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of
electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical
injury to yourself and/or damage to the equipment unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that
you should read.
Trademarks
IBM is a registered trademark of International Business Machines Corporation.
·
Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.
·
Other product and company names mentioned in this user’s manual may be the
·
trademarks of their respective holders.
Product revision
Because we at Digital Projection continually strive to improve our products, we
·
maychangespecificationsanddesigns,andaddnewfeatureswithoutprior
notice. Projectors built prior to this revision of the User Manual may therefore not
include all the features described.
Manual revision
Date Description Revision
15 October 2010 Rev A
Rev A October 2010 Page v
Page 6
Important Information Digital Projection HIGHlite 6000 User Manual
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this
equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling
into the projector. If this does happen, switch off immediately, and have
the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any
liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a
damaged power cable.
There are no user-serviceable parts inside the lamp module. The whole
module should be replaced.
Notes
Only lamps supplied by Digital Projection and intended for this
projector should be used. Fitting any other lamp could damage both
projector and lamp, and will invalidate the warranty.
Take care when removing the lamp module.
NEVERtouchthelamporreflector.
Take care not to touch the glass surface of the lamp module. If you
do accidentally touch the glass, it should be cleaned before use. (see
section 6. Maintenance.)
Do not use the lamp for more than 2000 hours, as this may cause
serious lamp failure, damage the lamp module and cause extra cost on
replacement.
HID lamps produce high intensity light. Do not look directly at the light
coming from the lamp housing, or the lens, or allow items such as
magnifying lenses to be placed in the light path. This could result in
serious eye damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could
causeafire
Always allow the projector to cool for 5 minutes before disconnecting
the power, moving the projector or changing the lamp.
Never use strong detergents or solvents such as alcohol or thinners to
clean the projector and lens.
Page vi Rev A October 2010
Page 7
Digital Projection HIGHlite 6000 User Manual Important Information
Installation precautions
Theprojectormustbeinstalledonlybysuitablyqualifiedpersonnel,in
accordance with local building codes.
The projector should be installed as close to the power outlet as
possible.
The power connection should be easily accessible, so that it can be
disconnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the
ventilation outlets and any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by
its operational heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 26 kg . Use safe handling
techniques when lifting the projector.
Do not stack more than three projectors.
When stacking projectors, the stack MUST be vertical, to ensure that
the stresses are distributed to all four chassis corners.
Before installation, make sure that the surface, ceiling or rigging that is
to support the projector is capable of supporting the combined weight
of all the projectors.
Notes
Backup safety chains or wires should always be used with ceiling
mount installations.
Do not place heavy objects on top of the projector chassis. Only the
chassis corners are capable of withstanding the weight of another
projector.
Do not drop or knock the projector.
Place the projector in a dry area away from sources of dust, moisture,
steam, smoke, sunlight or heat.
Do not tilt the projector more than ±12° in either direction when in use,
as this may cause serious lamp failure, damage the lamp module and
cause extra cost on replacement.
Operationandconfigurationprecautions
Software update should NOT be carried out except by, or with the
supervision of, Digital Projection Service personnel.
±12°
±12°
Rev A October 2010 Page vii
Page 8
Important Information Digital Projection HIGHlite 6000 User Manual
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 35 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
TheFederalCommunicationsCommissiondoesnotallowanymodificationsor
changestotheunitEXCEPTthosespecifiedbyDigitalProjectioninthismanual.
Failure to comply with this government regulation could void your right to operate
this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant with Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
European Waste Electrical and Electronic Equipment
(WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and
Electronic Equipment. Our products are designed with reuse, recycling
and recovery of all components in mind. To this end, at end of life, your
projector may be returned to Digital Projection Ltd or its agent so that the
environmental impact can be minimised.
Notes
Page viii Rev A October 2010
Page 9
Digital Projection HIGHlite 6000 User Manual Important Information
Digital Projection Contact details
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
RegisteredinEnglandNo.2207264,RegisteredOffice:asabove
Tel +44 (0) 161 947 3300
Fax +44 (0) 161 684 7674
Email enquiries@digitalprojection.co.uk, service@digitalprojection.co.uk
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email powerinfo@digitalprojection.com
Notes
Web Site www.digitalprojection.com
Rev A October 2010 Page ix
Page 10
HIGHlite 6000 User Manual
Contents
Declaration of Conformity ................................................................................................................... iii
Important Information
Symbols used in this guide ..................................................................................................................v
Warnings ..............................................................................................................................................v
Trademarks .........................................................................................................................................v
Product revision ......................................................................................................................................v
Manual revision .......................................................................................................................................v
General precautions ..............................................................................................................................vi
Installation precautions ...................................................................................................................... vii
Operationandconfigurationprecautions ......................................................................................vii
Compliance with international standards ...................................................................................... viii
Noise ................................................................................................................................................ viii
RF Interference.................................................................................................................................. viii
European Waste Electrical and Electronic Equipment (WEEE) Directive ................................................. viii
Digital Projection Contact details ......................................................................................................ix
1. Introduction
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front view ........................................................................................................................................ 1.4
Rear view ......................................................................................................................................... 1.4
2. Installation
Screen requirements ......................................................................................................................... 2.2
Positioning the screen and projector ................................................................................................... 2.2
Optimum viewing position ................................................................................................................. 2.2
Screen size vs throw distance ............................................................................................................ 2.3
Calculating screen width and throw distance ......................................................................................... 2.3
Shifting the Image.................................................................................................................... 2.4
Mounting the projector ..................................................................................................................... 2.5
Ceiling mounting .............................................................................................................................2.5
Level adjustment..............................................................................................................................2.5
Rear projection ............................................................................................................................... ..2.6
Stacking projectors .......................................................................................................................... . 2.6
Rev A October 2010 Page xi
continued
Page 11
Table of Contents Digital Projection HIGHlite 6000 User Manual
Connecting the projector ................................................................................................................ 2.7
Signal Inputs .................................................................................................................................. 2.7
Input connection examples .............................................................................................................. 2.7
Control connections ........................................................................................................................ 2.8
RS232 connection ........................................................................................................................ 2.8
RJ45 connection............................................................................................................................... 2.8
Power connection ........................................................................................................................... 2.9
3.Getting Started
Positioning the screen and projector ............................................................................................ 3.2
Switching the projector on ............................................................................................................... 3.2
Inserting batteries into the remote control ................................................................................... 3.2
Selecting an input signal or test pattern ....................................................................................... 3.3
Input ................................................................................................................................................ 3.3
Test pattern ...................................................................................................................................... 3.3
Adjusting the lens............................................................................................................................... 3.3
Zoom ............................................................................................................................................... 3.3
Focus .............................................................................................................................................. 3.3
Shift ................................................................................................................................................. 3.3
Adjusting the projected image ........................................................................................................ 3.4
Aspect ratio ...................................................................................................................................... 3.4
Image quality settings ........................................................................................................................ 3.4
Switching the projector off ............................................................................................................... 3.4
4. Controlling the projector
Overview ............................................................................................................................................... 4.3
Controlling the projector..................................................................................................................... 4.3
The control panel ................................................................................................................................ 4.4
LED status indicators ........................................................................................................................ 4.4
The remote control ............................................................................................................................. 4.5
Layout ............................................................................................................................................. 4.5
Timeout ........................................................................................................................................... 4.5
Using the control keys ...................................................................................................................... 4.6
Power .............................................................................................................................................. 4.6
Test pattern ..................................................................................................................................... 4.6
continued
Page xii Rev A October 2010
Page 12
Digital Projection HIGHlite 6000 User Manual Table of Contents
5. Userware
Introduction ....................................................................................................................................... 5.2
Info page ........................................................................................................................................... 5.3
PWR .............................................................................................................................................. 5.3
Image page .........................................................................................................................................5.4
Brightness / Contrast sliders..............................................................................................................5.4
Test pattern.......................................................................................................................................5.4
Lens page ......................................................................................................................................... 5.5
Lens Controls.................................................................................................................................. 5.5
MCGD page ........................................................................................................................................ 5.6
The MCGD measurement procedure ................................................................................................ 5.6
MCGD values ................................................................................................................................. 5.7
Download ....................................................................................................................................... 5.7
Write ........................................................................................................................................ 5.7
Read ....................................................................................................................................... 5.7
Save ........................................................................................................................................ 5.7
Open ....................................................................................................................................... 5.7
TCGD page ............................................................................................................................. 5.8
TCGD values ................................................................................................................................. 5.8
Select ........................................................................................................................................ 5.9
Save ........................................................................................................................................ 5.9
Open ....................................................................................................................................... 5.9
Write ........................................................................................................................................ 5.9
Read ....................................................................................................................................... 5.9
Discover page ............................................................................................................................. 5.10
Refresh ................................................................................................................................. 5.10
Unreacheable projectors.................................................................................................................. 5.10
Connect .................................................................................................................................... 5.11
Assign IP ................................................................................................................................... 5.11
continued
Rev A October 2010 Page xiii
Page 13
Table of Contents Digital Projection HIGHlite 6000 User Manual
6. Maintenance
Changing the lamp module .............................................................................................................. 6.2
Cleaning the fans ................................................................................................................................ 6.3
7. Appendix
Troubleshooting .................................................................................................................................. 7.2
Error codes ...................................................................................................................................... 7.4
Specifications ...................................................................................................................................... 7.5
Part numbers .................................................................................................................................... 7.5
Optical ............................................................................................................................................. 7.5
Electrical .......................................................................................................................................... 7.6
Physical ........................................................................................................................................... 7.6
Dimensions .......................................................................................................................................... 7.7
Video formats supported .................................................................................................................. 7.8
Input connections ............................................................................................................................. 7.10
HDMI 1 & 2 inputs ........................................................................................................................... 7.10
Control connections ........................................................................................................................ 7.11
Serial control input .......................................................................................................................... 7.11
Nullmodem cable ......................................................................................................................... 7.11
Serial port settings ........................................................................................................................ 7.11
Remote communications protocol ............................................................................................... 7.12
Introduction .................................................................................................................................... 7.12
Key Commands .............................................................................................................................. 7.12
Example ..................................................................................................................................... 7.12
The commands ............................................................................................................................ 7.12
Operation Commands ..................................................................................................................... 7.13
Example ..................................................................................................................................... 7.13
The commands ............................................................................................................................ 7.13
Page xiv Rev A October 2010
Page 14
1. Introduction
Contents
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front view ........................................................................................................................................ 1.4
Rear view ......................................................................................................................................... 1.4
Rev A October 2010 Page 1.1
Page 15
1. Introduction Digital Projection HIGHlite 6000 User Manual
What’s in the box?
Make sure your box contains everything listed. If any pieces are missing, contact
·
your dealer.
You should save the original box and packing materials, in case you ever need
·
to ship your Projector.
Projector
(Lenses available separately)
See parts list Section 7 Appendix
Notes
For more detailed information
about lenses, see Screen size
vs throw distance, in section
2. Installation.
Only one power cable
dependent on the destination
territory will be supplied with
the projector.
Power cable 10A
Europe (102-163)
Remote control
(110-024)
2x AA batteries
Power cable 13
A North America
(102-165)
User manual on CD
HDMI cable
(111-339)
Page 1.2 Rev A October 2010
Page 16
Digital Projection HIGHllite 6000 User Manual 1. Introduction
Key features of the projector
Congratulations on your purchase of the Digital Projection HIGHlite 6000
projector.
DigitalProjectionInternational(DPI),TexasInstruments’firstDLP®partnerandthe
original innovator of the 3chip DLP® projector, proudly introduces the new HIGHlite
6000series,ahighbrightness1080pplatformwiththeimagingfidelityofTexas
Instruments’ DLP® technology. The 3-chip HIGHlite series adds a remarkably
affordable, highlumen line of 1920 x 1080 displays to DPI’s already extensive
3-chip product line.
TheimagerybenefitsassociatedwiththeHIGHlitearenumerous,withdazzlingly
bright images and superior DLP® image fidelity. Applicable to a wide variety of
commercial venues, including those contending with high ambient light, the HIGHlite
series offers rich, saturated imagery.
Installation is incredibly flexible due to the the HIGHLite's compact and lightweight
chassis design, and extraordinary lens shift range of 30% horizontal and 120%
vertical. Multiple lens options provide further flexibility, with a throw range from .77 to
6.76:. Connectivity is via HDMI.
Providing a bright, saturated image from a smallform 3-chip display, the HIGHlite
6000 presents a powerful yet remarkably affordable solution for a
variety of commercial and home entertainment applications, including: E-Cinema, DCinema,boardrooms and conference centers, visualization/simulation environments,
retail, entertainment, digital media/advertising and hospitality, Media rooms and
home theatres, Training and education.
Notes
Key Features
High resolution projector for medium sized venues
·
Applications:MediumsizedScreen;FixedinstallandRental
·
Brightness 6000 ANSI lumens ±10%
·
Contrast 2000:1 ±10%
·
1920 x 1080 resolution
·
Precision mechanical design ensuring maximum amount of light from lamp
·
housing reaches optics, without any operator adjustment
·
400 - 500W single phase, 100 - 240VAC ±10%
·
Compact size, approximately 26 kg
·
Robust metal case
·
RS232 / RJ45 connection for remote operation using control codes
·
HDMI input as standard
·
IR remote control for easy setup
Rev A October 2010 Page 1.3
Page 17
1. Introduction Digital Projection HIGHlite 6000 User Manual
Getting to know the projector
Front view
Front Infrared
window
(remote control)
Lens
Notes
Projector control
panel
For more detailed information
about lenses or lens shift, see
section 2. Installation
Air outlet
Rear view
Lamp cover
Input
connections
connection
Adjustable feet
Rear Infrared
window (remote
control)
For information about how to
changethelamporthefilter,
see section 6. Maintenance.
For information about controls
and indicators, see section
4. Controlling the projector.
Air inlet
Power
Page 1.4 Rev A October 2010
Page 18
2. Installation
Contents
Screen requirements ......................................................................................................................... 2.2
Positioning the screen and projector ................................................................................................... 2.2
Optimum viewing position ................................................................................................................. 2.2
Screen size vs throw distance ............................................................................................................ 2.3
Calculating screen width and throw distance ......................................................................................... 2.3
Fitting and Removing a Lens ............................................................................................ 2.4
Shifting the Image.................................................................................................................... 2.5
Mounting the projector ..................................................................................................................... 2.6
Ceiling mounting .............................................................................................................................2.6
Level adjustment..............................................................................................................................2.6
Rear projection ............................................................................................................................... ..2.7
Stacking projectors .......................................................................................................................... . 2.7
Connecting the projector ................................................................................................................ 2.8
Signal Inputs .................................................................................................................................. 2.8
Input connection examples .............................................................................................................. 2.8
Control connections ........................................................................................................................ 2.9
RS232 connection ........................................................................................................................ 2.9
RJ45 connection............................................................................................................................... 2.9
Power connection ........................................................................................................................... 2.10
Rev A October 2010 Page 2.1
Page 19
2. Installation Digital Projection HIGHlite 6000 User Manual
Positioning the screen and projector
Optimum viewing position
Foroptimumviewing,thescreenshouldbeaflatsurfaceperpendiculartothefloor.
Thebottomofthescreenshouldbe1.2m(4feet)abovethefloorandthefrontrow
of the audience should not have to look up more than 30° to see the top of the
screen.
The distance between the front row of the audience and the screen should be at
least twice the screen height and the distance between the back row and the screen
should be a maximum of 8 times the screen height. The screen viewing area should
be within a 60° range from the face of the screen.
Notes
The projector should be
installed as close to the
power outlet as possible.
The power connection should
be easily accessible, so that
it can be disconnected in an
emergency.
Ensure that there is at least
30cm (12in) of space between
the ventilation outlets and
any wall, and 10cm (4in) on
all other sides.
Do not install the projector
close to anything that
might be affected by its
operational heat, for instance,
polystyrene ceiling tiles,
curtains etc.
Page 2.2 Rev A October 2010
Page 20
Digital Projection HIGHlite 6000 User Manual 2. Installation
Screen size vs throw distance
Throw distance is the distance measured from the front of the projector to the
screen. This is an important calculation in any projector installation as it determines
whether or not you have enough room to install your projector with the desired
screen size, and if your image will be the right size for your screen.
Calculating screen width and throw distance
Throw Distance = Screen Width x Lens Throw Ratio
Screen Width =
Throw Distance
Lens Throw Ratio
Notes
The following lenses are available.
Throw Ratio Focus range
Fixed lens 0.77:1 1.3 - 2.45m
Fixed lens 1.16:1 1.4 - 6.2m
Zoom lens 1.45–1.74:1 zoom 1.8 - 9.3m
Zoom lens 1.74–2.17:1 zoom 2.2 - 11.8m (standard lens)
Zoom lens 2.17–2.90:1 zoom 2.7 - 15.4m
Zoom lens 2.90 - 4.34:1 zoom 3.6 - 22.5m
Zoom lens 4.34–6.76:1 zoom 5.5 - 35m
ThesethrowratiosarecorrectforimagesthatfillthefullwidthoftheDMD.For
imagesthatdonotfillthefullwidth,thethrowratiowillbelarger.For4:3images,
the throw ratio is increased by a factor of 1.33. The effect of this can be seen on
the lens charts on the following pages.
Do not confuse the focus range
with the zoom range:
The focus range is the distanc
e over which the image can be
focused .
The zoom range is the range
over which the throw ratio can
be changed using the zoom
control.
Rev A October 2010 Page 2.3
Page 21
2. Installation Digital Projection HIGHlite 6000 User Manual
Fitting and Removing a Lens
Remove the front cover by removing the 2 screws at either side of the front cover,
and sliding the front cover down to remove.
Insert the lens ensuring you push firmly fully into the projector then rotate the
lens clockwise until the lens locks onto the catch at the top of the lens mount.
Notes
To remove the lens, press and hold down the locking catch at the top of the lens
mount, rotate the lens slightly anticlockwise and then carefully remove the lens.
Refit the front cover after fitting or removing a lens as required.
Page 2.4 Rev A October 2010
Page 22
2. Installation Digital Projection HIGHlite 6000 User Manual
Shifting the image
Ideally, the projector should be positioned perpendicular to the screen.
The normal position for the projector is at the centre of the screen. However, you
can set the projector above or below the centre, or to one side, and adjust the image
using the Lens shift controls on the remote control to maintain a geometrically
correct image.
The image can be shifted by up to:
Notes
If the lens is to be shifted in
two directions combined, the
maximum range is somewhat
less, as can be seen below.
± 0.6 of the height of a full screen image (known as 120% shift)
·
± 0.15 of the width of a full screen image (known as 30%)
·
It may physically possible to shift the lens further than this, however there will be so
medistortionoftheimagebeyondtherangesspecifiedabove.
+ 0.6 H
– 0.15 W
+ 0.15 W
full horizontal or vertical shift
without distortion
combined shift
is reduced
Page 2.5 Rev A October 2010
Page 23
Digital Projection HIGHlite 6000 User Manual 2. Installation
Mounting the projector
The four adjustable feet under the chassis allow the projector to be lowered onto a
flatsurfacewithoutanydangerofhandsbeingtrappedbetweenthebottomframe
and the surface.
Ceiling mounting
Theprojectorisdesignedtobeusedonaflatsurface,butitcanbesuspended
from a ceiling. Three M4 mounting holes with a 0.7mm pitch are provided under the
projector to allow bolting to a ceiling mounting plate.
Dimension
s in mm
Notes
BEFORE INSTALLING THE
PROJECTOR, READ ALL THE
WARNINGS BELOW AND
ALL THOSE IN IMPORTANT
INFORMATION AT THE
FRONT OF THIS MANUAL.
The projector weighs
approximately 26 kg Use
safe handling techniques
when lifting the projector.
Make sure that the surface,
ceiling or rigging that is
to support the projector is
capable of supporting the
weight of the projector.
Backup safety chains or
wires should always be
used with ceiling mount
installations.
To use the projector upside down, please contact your dealer to electronically invert
the image.
Level adjustment
Iftheprojectoristobeoperatedfromaflatsurfacesuchasaprojectortable,then
adjustment of projector level should be made by turning the four feet under the
chassis.
Ideally, the projector should be positioned perpendicular to the screen, and the lens
shift controls used to align the image with the screen, to maintain a geometrically
correct image.
Do not tilt the projector more
than ±12° in either direction
when in use, as this may
cause serious lamp failure,
damage the lamp module
and cause extra cost on
replacement.
±12°
±12°
Rev A October 2010 Page 2.6
Page 24
2. Installation Digital Projection HIGHlite 6000 User Manual
Rear projection
To use rear projection, please contact your dealer to electronically invert the image.
In rearscreen applications where space behind the projector is limited, a mirror may
be used to fold the optical path. The position of the projector and mirror must be
accurately set. If you are considering this type of installation, contact your dealer for
assistance
Stacking projectors
The projector is capable of supporting the weight of up to three other projectors
safely. The stack should be positioned vertically and perpendicular to the screen,
and the lens shift controls used to align the image with the screen, to maintain a
geometrically correct image.
Carefully lower each projector down onto the top of the others, making sure that
·
they are vertically aligned with each other, and protected from becoming pushed
over.
Align the images from the projectors, using the Lens shift controls on the remote
·
control.
Notes
Do not try to stack more than
three projectors.
When stacking projectors,
the stack MUST be vertical, to
ensure that the stresses are
distributed to all four chassis
corners.
Make sure that the surface,
ceiling or rigging that is
to support the projector is
capable of supporting the
combined weight of all the
projectors.
Do not place heavy objects
on top of the projector
chassis. Only the chassis
corners are capable of
withstanding the weight of
another projector.
Backup safety chains or
wires should always be
used with ceiling mount
installations.
Page 2.7 Rev A october 2010
Page 25
Digital Projection HIGHlite 6000 User Manual 2. Installation
Connecting the projector
Signal Inputs
The following inputs are available:
HDMI 1 HDMI 2
HDMI 1 & 2 HDCPcompliant digital video inputs from HDMI or DVI sources.
Only HDMI 1 enabled by default. To switch to HDMI 2 please
contact your dealer.
Notes
Input connection examples
For more information about pin
connections see section 7.
Appendix.
Rev A October 2010 Page 2.8
Page 26
Digital Projection HIGHlite 6000 User Manual 2. Installation
Control connections
The following connections are available:
LAN
RS232 connection
All of the projector’s features can be controlled via a serial connection.
TheRS232connectioncanalsobeusedtodownloadthefirmwareupdates,issued
from time to time by Digital Projection.
RS232
Projector
Notes
For more information about pin
connections see section 7.
Appendix.
Computer
RJ45 LAN connection
All of the projector’s features can be controlled via an ethernet connection.
Crossed
Computer
Uncrossed
LAN cables
Hub
Projector
Computer
Projector
Projector
Rev A October 2010 Page 2.9
Page 27
2. Installation Digital Projection HIGHlite 6000 User Manual
Power connection
Liftthecablelockup,pushthemainsconnectorinfirmly,thenpushthelockdownto
secure the cable.
Power
connection
Notes
Use only the power cable
provided.
Ensure that the power
outlet includes a Ground
connection, as this
equipment MUST be earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a damaged
power cable.
Page 2.10 Rev A October 2010
Page 28
3. Getting Started
Contents
Positioning the screen and projector ............................................................................................ 3.2
Switching the projector on ............................................................................................................... 3.2
Inserting batteries into the remote control ................................................................................... 3.2
Selecting an input signal or test pattern ....................................................................................... 3.3
Input ................................................................................................................................................ 3.3
Test pattern ...................................................................................................................................... 3.3
Adjusting the lens............................................................................................................................... 3.3
Zoom ............................................................................................................................................... 3.3
Focus .............................................................................................................................................. 3.3
Shift ................................................................................................................................................. 3.3
Adjusting the projected image ........................................................................................................ 3.4
Aspect ratio ...................................................................................................................................... 3.4
Image quality settings ........................................................................................................................ 3.4
Switching the projector off ............................................................................................................... 3.4
Rev A October 2010 Page 3.1
Page 29
3. Getting Started Digital Projection HIGHlite 6000 User Manual
Positioning the screen and projector
Install the screen, ensuring that it is in the best position for viewing by your
·
audience.
Mount the projector, ensuring that it is at a suitable distance from the screen for
·
theimagetofillthescreen,andthatitisperpendiculartothesceen.
Switching the projector on
Connect the power cable between the mains supply and the projector.
·
Wait until the selftest has completed and the standby indicator on the projector
control panel shows amber. The lamp will be off and the projector will be in
STANDBY mode.
Projector
control panel
Notes
For more information about
positioning the screen and
projector, see Positioning
the screen and projector, in
section 2. of the User Manual:
Installation.
For more detailed information
about:
using the control keys on the
remote control or the projector
control panel,
Power
connection
Press POWER ON on the remote control or POWER on the projector
·
control panel to switch the projector ON. The power indicator on the control
panelwillflashblueforapproximately30seconds,whilstthelampcomesupto
full brightness. When the projector is ready for use, the power indicator will show
a steady blue.
Inserting batteries into the remote control
Open the battery compartment and insert two AA size batteries
·
(supplied), making sure they are inserted the correct way round, as shown
below.
section 5. of the User
see
Manual: Controlling the
projector.
If the red ISSUE indicator is
illuminated continuously or
flashing,see Error Codes in
section 7 of the User Manual:
Appendix, for more information
Do not mix an old battery with
a new one or different types of
batteries.
If you will not use the remote
control for a long time, remove
the batteries to avoid damage
from battery leakage.
Page 3.2 Rev A October 2010
Page 30
Digital Projection HIGHlite 6000 User Manual 3. Getting Started
Selecting an input signal or test pattern
Input
·
Connect an HDMI video source to the projector. The signal should be
automatically detected by the projector, and should be displayed within a two or
three seconds.
Test pattern
If you have no video source connected to the projector, then you can display a test
pattern as follows:
Press
·
At the end of the test pattern sequence you will be returned to the source image.
on the remote control, until the desired test pattern is displayed.
Notes
For more information about
connecting input signals, see
Signal Inputs, in section 2. of
the User Manual: Installation.
For more detailed information
about input connections, see
Input signals in section 6.
Adjusting the lens
Focus
·
Press the Lens button on the remote control. The first press selects focus. Agrid
pattern will appear on the sceen and a legend indicating focus is selected. Use
the up and down arrow keys until the picture is sharp.
Zoom
·
Press the Lens button on the remote control. The second press selects zoom.
Agrid pattern will appear on the sceen and a legend indicating zoom is selected.
Use the up and down arrow keys until the picture is the required size.
Shift
·
Press the Lens button on the remote control. The third press selects shift.
Agrid pattern will appear on the sceen and a legend indicating shift is selected.
Use the up, down, left and right arrow keys until the picture is in the required
position.
For more information about lens
shift, see Shifting the image in
section 2. of the User Manual:
Installation.
Rev A October 2010 Page 3.3
Page 31
3. Getting Started Digital Projection HIGHlite 6000 User Manual
Adjusting the projected image
Lens Shift
·
Press
Each press of the lens button will cycle through the lens functions in the following
order:
1. FOCUS
2. ZOOM
3. SHIFT
A test pattern with a function indicator will be shown with each press of the lens
button. The pattern will time out after 15s of no button presses, or can be removed
by pressing the menu or OK button.
LENS
on the remote control until the function required is shown.
Notes
Image Quality
No image quality adjustments can be made from the remote control. Please refer to
the Userware Section 5
Brightness
Contrast
Switching the projector off
Press POWER OFF on the remote control or POWER on the
·
projectorcontrolpanel,thenpressthebuttonasecondtimetoconfirmyour
intention to switch off.
Thelampwillswitchoff,andthepowerindicatoronthecontrolpanelwillflash
blue for approximately 30 seconds until the lamp has cooled down.
Wait until the power indicator has switched off and the standby indicator on the
·
projector control panel shows amber. The projector will now be in STANDBY
mode.
Disconnect the power cable from the projector.
·
Page 3.4 Rev A October 2010
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
moving the projector
- changing the lamp
Page 32
4. Controlling the projector
Contents
Overview ............................................................................................................................................... 4.3
Controlling the projector..................................................................................................................... 4.3
The control panel ................................................................................................................................ 4.4
LED status indicators ........................................................................................................................ 4.4
The remote control ............................................................................................................................. 4.5
Layout ............................................................................................................................................. 4.5
Timeout ........................................................................................................................................... 4.5
Using the control keys ...................................................................................................................... 4.6
Power .............................................................................................................................................. 4.6
Test pattern ..................................................................................................................................... 4.6
Rev A October 2010 Page 4.1
Page 33
Digital Projection HIGHlite 6000 User Manual 4. Controlling the projector
Overview
Controlling the projector
·
The projector is controlled in the following ways.
·
the remote control (Power and Lens Functions Only)
·
the projector control panel (Power Only)
·
the RS232 input (Firmware Updates and Protocol Commands)
·
the RJ45 input (Protocol Commands, Userware Application)
For more information about controlling the projector using the RS232 or RJ45 input,
see.
Remote communications protocol in section 7. Appendix.
For information about how to connect the projector, see Connecting the
projector in section 2. Installation, and Connections in section 7. Appendix.
The Projector has no On Screen Display therefore many features are controlled
from the Userware application. See section 5. Userware.
Notes
Rev A October 2010 Page 4.3
Page 34
4. Controlling the projector Digital Projection HIGHlite 6000 User Manual
The control panel
The projector control panel is designed to be read from the front or rear of the
projector, for ease of use. The arrow keys have no function on this model.
Notes
POWER
SOURCE This button has no function.
Press this once to switch the projector ON or twice to switch it to
STANDBY mode.
LED status indicators
The indicators on the control panel are as follows:
POWER off = NO POWER steady blue = normal RUNNING mode
flashingblue
ISSUE off = NO ERROR flashingorsteadyred = ERROR
STANDBY amber = STANDBY mode
= LAMP WARMUP or COOLDOWN mode
Always allow the lamp to cool
for 5 minutes before:
moving the projector
- changing the lamp
If the red ISSUE indicator is
illuminated continuously or
flashing,see Error Codes in
section 7.
Page 4.4 Rev A October 2010
Page 35
Digital Projection HIGHlite 6000 User Manual 4. Controlling the projector
The remote control
Layout
Transmit
indicator
Notes
In most situations, you can
simply point the remote control
atthescreenwhichwillreflect
the IR signal from the remote
back toward the receiver on the
projector.
LENS
Timeout
There is a 15 second timeout for the lens navigation keys.
In some cases, however,
ambient conditions may prevent
this. In this case, point the
remote control directly at the
projector.
Remote reception angle
40°
40°
Rev A October 2010 Page 4.5
Page 36
4. Controlling the projector Digital Projection HIGHlite 6000 User Manual
Using the control keys
Power
Press POWER ON on the remote control to switch the projector ON.
Thepowerindicatoronthecontrolpanelwillflashblueforapproximately3
0
seconds, whilst the lamp comes up to full brightness. When the projector is
ready for use, the power indicator will show a steady blue.
on the remote control to switch the projector to
STANDBY mode.
PressthebuttonasecondtimetoconfirmyourintentiontoswitchtoSTANDBY
mode.
Thelampwillswitchoff,andthepowerindicatoronthecontrolpanelwillflash
blue for approximately 30 seconds until the lamp has cooled down. Wait until
the power indicator has switched off and the standby indicator on the projector
control panel shows amber. The projector will now be in STANDBY mode.
Test pattern
Press the key repeatedly to cycle through the Test patterns, in the
·
following order:
White, Black, Red, Green, Blue, Cyan, Magenta, Yellow, Chequerboard,
Greyscale, Alignment grid, White...
Notes
Page 4.6 Rev A October 2010
Page 37
5. Userware
Contents
Introduction ....................................................................................................................................... 5.2
Info page ........................................................................................................................................... 5.3
PWR .............................................................................................................................................. 5.3
Image page .........................................................................................................................................5.4
Brightness / Contrast sliders..............................................................................................................5.4
Test pattern.......................................................................................................................................5.4
Lens page ......................................................................................................................................... 5.5
Lens Controls.................................................................................................................................. 5.5
MCGD page ........................................................................................................................................ 5.6
The MCGD measurement procedure ................................................................................................ 5.6
MCGD values ................................................................................................................................. 5.7
Download ....................................................................................................................................... 5.7
Write ........................................................................................................................................ 5.7
Read ....................................................................................................................................... 5.7
Save ........................................................................................................................................ 5.7
Open ....................................................................................................................................... 5.7
TCGD page ............................................................................................................................. 5.8
TCGD values ................................................................................................................................. 5.8
Select ........................................................................................................................................ 5.9
Save ........................................................................................................................................ 5.9
Open ....................................................................................................................................... 5.9
Write ........................................................................................................................................ 5.9
Read ....................................................................................................................................... 5.9
Discover page ............................................................................................................................. 5.10
Refresh ................................................................................................................................. 5.10
Unreacheable projectors.................................................................................................................. 5.10
Connect ........................................................................................................................................ 5.11
Assign IP ....................................................................................................................................... 5.11
Rev A October 2010 Page 5.1
Page 38
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
Digital Projection HIGHlite 6000 User Manual 5. Userware
Introduction
The Why-I Userware provides an intuitive interface to enable control of many of
the features of the projector from a personal computer, via a LAN connection.
Because the HIGHlite 6000 is not equipped with an on screen display, most of the
features are only available from external control applications such as this.
When the Userware is started, the Info page will display immediately. The Page
buttons are always visible at the sideof the display:
If the projector is able to connect to the computer you will see the screen shown
below if the projector is in standby mode. Some information such as temperature
are not available in standby mode.
Notes
To use the Why-I Userware the
j ava Runtime Environment
software must be installed on
your computer.This software
can be downloaded, free of
charge from www.java.com.
The LAN IP Address of the
projector can be found on the
Discovery page of the
userware. See section 4.
Controlling the projector.
The Userware can be used to
control only one projector at a
time, and only one instance can
be running at one time.
More than one computer can be
used to control more than one
projector on the same network.
Rev A August 2009 Page 5.3
Rev A October 2010 Page 5.2
Page 39
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
Digital Projection HIGlite 6000 User Manual 5. Userware
Info page
TheInfopageisthefirsttodisplaywhenthecomputerconnectstotheprojector.
To return to the Info page at any time, click on Info.
·
Notes
PWR
Click PWR to switch the projector On. The button will turn green.
·
Click PWR to switch the projector into Standby mode. The button will turn red.
·
Information presented on this page.
Projector Serial Number
Firmware Version
Model Name
Software Version
IP Address
Connected
Lamp Hours
Total Hours
Temperatures
LampStatus Icon
Status Message
Rev A August 2009 Page 5.5
Rev A October 2010 Page 5.3
Page 40
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
5. Userware Digital Projection HIGHlite 6000 User Manual
Image page
The Info page gives access to Brightness, Contrast and Test Patterns
To return to the Image page at any time, click on Image.·
Brightness / Contrast sliders
Click on Brightness or Contrast sliders and click on the arrows or drag the
adjuster to make adjustments. Clicking on the value number will return to a
default value.
Test Pattern
Click on Test Pattern to select from the drop down menu:·
Page 5.8 Rev A August 2009
Page 5.4 Rev A October 2010
Test
Pattern
For more information about
test patterns, see Setup menu,
in section 4. Controlling the
Projector.
Page 41
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
Digital Projection HIGHlite 6000 User Manual 5. Userware
Lens page
To see the Lens page, click on Lens.
·
Notes
Lens
controls
Lens controls
Click on the buttons to Move, Focus and Zoom the lens.
·
Hold the button down until the desired settings are achieved.
Release the button to stop the lens from moving.
Rev A August 2009 Page 5.9
Rev A October 2010 Page 5.5
Page 42
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
5. Userware Digital Projection HIGHlite 6000 User Manual
MCGD page
MCGD Measured Colour Gamut Data can be used to correct for a number of
environmental variables, for example:
two or more different projectors
lamp age
different lenses
ambient light
screen characteristics
The MCGD measurement procedure
1 On the Image page, select the White Uncorrected test pattern.
2 Using a photospectrometer, measure and record the following values:
White x y
3 On the Image page, select the Red Uncorrected test pattern.
4 Using a photospectrometer, measure and record the following values:
Red x y
5 Continue this process for the Green and Blue measurements.
6 Enter all the values into the MCGD page, as described on the next page.
Notes
Read the notes on MCGD,
TCGD and ColorMAX below,
before making any MCGD
settings.
Notes on MCGD, TCGD and ColorMAX User settings
TCGD (see the next section)
The parameters entered on the TCGD page establish the target settings that the
projectorneedstoaimfor,inordertogiveaspecifiedcolourgamut.
MCGD (see this section)
The parameters entered on the MCGD page establish the starting settings, from
which the projector will calculate what adjustments are necessary to achieve the
colorgamutspecifiedonthe TCGD page.
Only one set of MCGD data can be stored on the projector, but many more can be
stored on a computer, and retrieved using the MCGD page controls.
ColorMAX User settings
Only two sets of color gamut parameters can be stored on the projector
ColorMAX User 1 and ColorMAX User 2 - but many more can be stored on a
computer, and retrieved using the TCGD page controls.
Page 5.14 Rev A August 2009
Page 5.6 Rev A October 2010
Page 43
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
Digital Projection HIGHlite 6000 User Manual 5. Userware
MCGD page continued
To see the MCGD page, click on MCGD .
Onfirstenteringthe MCGD screen, the MCGD values will show those currently
loaded into the projector.
MCGD
values
Notes
Read the notes on MCGD,
TCGD and ColorMAX earlier
in this section before making
any MCGD settings.
1. New MCGD values will not
be downloaded to the projector
until the Write button is
pressed.
MCGD values
To enter MCGD values, click on each box in turn, and enter the measured x and
y values for each colour.
Write
Click on Write to save the values on screen to the projector.
Read
Click on Read to show the values currently saved on the projector.
Save
Click on Save to save the values on screen to a MCGDfile on the computer.
Whenprompted,enterafilenameorbrowsetoanexistingfilethatistobe
overwritten.
Open
To retrieve a set of saved MCGD values, click on Open.
MCGDfilesarenamed
filename.mcgd.
Whenprompted,enterafilenameorbrowsetothefilethatistobeopened.
Rev A August 2009 Page 5.15
Rev A October 2010 Page 5.7
Page 44
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
5. Userware Digital Projection HIGHlite 6000 User Manual
TCGD page
TCGD - Target Colour Gamut Data - can be used to match the display to a pre-
definedcolourgamut,forexample:
to match the MCGD values from another projector
tomatchaspecificationfromthefilmmaker
To see the TCGD page, click on TCGD.
·
TCG
Notes
Read the notes on MCGD,
TCGD and ColorMAX earlier
in this section before making
any TCGD settings.
D
1. New TCGD values will not be
applied to the projector until the
Download button is pressed.
TCGD values
To enter TCGD values manually, click on each box in turn, and enter the x and y
·
values for each colour.
x and y are the colour coordinates.
2. The values will not be used
until the ColorMAX User 1 or
ColorMAX User 2 is chosen
in the drop down list and the
Select button is pressed.
Page 5.16 Rev A August 2009
Page 5.8 Rev A October 2010
Page 45
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
Digital Projection HIGHlite 6000 User Manual 5. Userware
TCGD page continued
Select
Click on Select to activate the color gamut selected on the drop down list.
Save
Click on Save to save the values on screen to a TCGDfile on the computer.
Whenprompted,enterafilenameorbrowsetoanexistingfilethatistobe
overwritten.
Open
To retrieve a set of saved TCGD values, click on Open .
Whenprompted,enterafilenameorbrowsetothefilethatistobeopened.
Write
Click on Write to save the values on screen to the selected drop down list
location. N.B. Not all locations may be written to. If your chosen location is not
writeable a warning will appear as below.
Notes
Read the notes on MCGD,
TCGD and ColorMAX earlier
in this section before making
any MCGD settings.
TCGDfilesarenamedfilename.
tcgd.
Read
Click on the drop down list to chose the gamut settings you want to retrieve
from the projector and then press Read. N.B. Some settings such as Auto may
not be read and a dialogue similar to above will advise you.
Rev A August 2009 Page 5.17
Rev A October 2010 Page 5.9
Page 46
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
Digital Projection HIGHlite 6000 User Manual 5. Userware
Discover page
To see the Discover page, click on Discover.
·
If any projectors are found on the network, then its
listed in the panel and marked Online. The first projector in the list will be
connected to if possible.
Projector Connected will be shown at the top left, together with the projector’s
IP Address.
LAN IP
address will be
Notes
The Userware can be used to
control only one projector at a
time, and only one instance can
be running at one time.
Discover page can be
The
used to switch control between
multiple projectors.
More than one computer can be
used to control more than one
projector on the same network.
Refresh
·
Click on Refresh to update the list of discovered
projectors and automatically connect to the first
discovered projector if possible.
Unreachable projectors
·
If a projector is found on the network, but can not be
connected to, a dialogue box will appear (see below)
indictating why the projector can not be connected. The
most common reason being different subnets.
Rev A August 2009 Page 5.25
Rev A October 2010 Page 5.10
Page 47
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
5. Userware Digital Projection HIGHlite 6000 User Manual
Connect
Double Click on the IP Address of the projector you want to
connect to. Any projector already connected will be
automatically disconnected.
Assign IP
Click on the Assign IP to change the IP settings of the
projector. You may need to configure your PC to connect to the
projector in order to make changes. The IP configuration page
will open in a Web Browser.
Notes
The Userware can be used to
control only one projector at a
time, and only one instance can
be running at one time.
Discover page can be
The
used to switch control between
multiple projectors.
More than one computer can be
used to control more than one
projector on the same network.
Page 5.26 Rev A August 2009
Page 5.11 Rev A October 2010
Page 48
6. Maintenance
Contents
Changing the lamp module .............................................................................................................. 6.2
Cleaning the fans ................................................................................................................................ 6.3
Rev A October 2010 Page 6.1
Page 49
6. Maintenance Digital Projection HIGHlite 6000 User Manual
Changing the lamp module
Turn the power OFF and allow the lamp to cool for 5 minutes.
·
Unscrewthecaptivefingerscrewsecuringthelampdoor,andremovethedoor.
·
Unscrew the two crosshead screws securing the lamp module to the projector
·
Lift the wire handle up and use it to pull out the lamp module.
·
Notes
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
moving the projector
- changing the lamp
There are no user-serviceable
parts inside the lamp module.
The whole module should be
replaced.
Only lamps supplied by
Digital Projection and
intended for this projector
should be used. Fitting any
other lamp could damage
both projector and lamp, and
will invalidate the warranty.
At the end of life, the lamp
will not strike, and the Issue
indicator on the control panel
willflashred.(Typicallamplife
is 2000 hours)
Fitanewlampmodule,pushingitfirmlyintoplace.
·
Tighten the two cross-head screws.
·
Locatethetwolugsatthebottomofthelampdoorintotheslots,andrefitthe
·
door.Tightenthefingerscrew.
Do not use the lamp for more
than 2000 hours, as this may
cause serious lamp failure,
damage the lamp module
and cause extra cost on
replacement.
Take care not to touch the
glass surface of the lamp
module. If you do accidentally
touch the glass, it should be
cleaned before use.
HID lamps produce high
intensity light. Do not look
directly at the light coming
from the lamp housing or the
lens.
Opening the lamp door will
switch the projector OFF. The
projector cannot be operated
until the door is fully closed.
Page 6.2 Rev A October 2010
Page 50
Digital Projection HIGHlite 6000 User Manual 6. Maintenance
Cleaning the fans
Turn the power OFF and wait until the fans stop.
·
Use a vacuum cleaner to clean the inlet and outlet fans, as shown below.
·
Notes
Always switch the projector
OFF before cleaning the fans.
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
moving the projector
- changing the lamp
The fans should be cleaned
regularly:
In a clean environment such as
·
anoffice,after500hours.
In a dusty or smoky
·
environment such as a theatre
or public area, more frequent
cleaning may be necessary.
Rev A October 2010 Page 6.3
Page 51
7. Appendix
Contents
Troubleshooting .................................................................................................................................. 7.2
Error codes ...................................................................................................................................... 7.4
Specifications ...................................................................................................................................... 7.5
Part numbers .................................................................................................................................... 7.5
Optical ............................................................................................................................................. 7.5
Electrical .......................................................................................................................................... 7.6
Physical ........................................................................................................................................... 7.6
Dimensions .......................................................................................................................................... 7.7
Video formats supported .................................................................................................................. 7.8
Input connections ............................................................................................................................. 7.10
HDMI 1 & 2 inputs ........................................................................................................................... 7.10
Control connections ........................................................................................................................ 7.11
Serial control input .......................................................................................................................... 7.11
Nullmodem cable ......................................................................................................................... 7.11
Serial port settings ........................................................................................................................ 7.11
Remote communications protocol ............................................................................................... 7.12
Introduction .................................................................................................................................... 7.12
Key Commands .............................................................................................................................. 7.12
Example ..................................................................................................................................... 7.12
The commands ............................................................................................................................ 7.12
Operation Commands ..................................................................................................................... 7.13
Example ..................................................................................................................................... 7.13
The commands ............................................................................................................................ 7.13
Rev A October 2010 Page 7.1
Page 52
7. Appendix Digital Projection HIGHlite 6000 User Manual
Troubleshooting
problem possible solutions
The red ISSUE indicator is illuminated
continuouslyorflashing.
The projector will not power up. Check that the mains plug is plugged in and that the mains supply is switched on.
Check the Error codes detailed on the next page.
Check that the lamp door is closed properly.
Check any external fuses or breakers.
The projector will not power up shortly
after being switched off.
The projector shuts down after it has
been in use for some time.
No image is displayed. See section 6. Maintenance, Changing the lamp
To protect the lamp, the projector cannot be switched on when in it is in cooldown
mode.Waituntilthepowerindicatorstopsflashingblue,andthestandbyindicator
shows amber.
The projector may be overheating. Check that the air inlets and outlets are clear
of any obstruction.
See section 6. Maintenance, Cleaning the fans
It is possible to increase the speed of the fans for use in a high altitude
environment:
See section 4. Controlling the projector, System menu
Check that the input source is switched on and connected to the projector
correctly.
Check that the brightness and contrast settings are set correctly.
See section 4. Controlling the projector, Using the control keys and Main
menu
The projector may be overheating. Check that the air inlets and outlets are clear
of any obstruction.
Theimagedoesnotfitthescreen
correctly.
Uneven image quality. Check that the projector is parallel to the screen.
Check that the projector and screen size are positioned correctly, and that the
zoom is adjusted correctly.
See section 2. Installation, Screen size vs throw distance
Check the aspect ratio setting.
See section 4. Controlling the projector, Main menus
Checkthatthescreenisflat,andsecurelymounted.
Page 7.2 Rev A October 2010
Page 53
Digital Projection HIGHlite 6000 User Manual 7. Appendix
problem possible solutions
Image is split or otherwise scrambled. Check the source is suitable for the projector.
Image is blurred. Check that the lens is focussed correctly.
Image is too bright, and lacks
definitioninthebrightareas.
Image appears ‘washed out’ and is too
bright in the dark areas
Projector does not respond to control
commands from a computer.
Projector does not respond to control
commands from the remote control.
Decrease the contrast setting.
See section 4. Controlling the projector, Using the control keys and Main
menu
Decrease the brightness setting.
See section 4. Controlling the projector, Using the control keys and Main
menu
Check that the serial cable is connected correctly.
Check that the baud rate is set correctly.
See this section 7. Appendix, Connections
Check that the correct control codes are being used.
See this section 7. Appendix. Serial communications protocol
Check that the infra red windows at the front and rear of the projector or on the IR
repeater are not obstructed. Check that the batteries are in good condition.
If you are using an IR repeater, check that the cable is connected properly at both
ends, and that the cable is not damaged.
See section 4. Controlling the projector, The remote control
In the event that this troubleshooting guide has not solved the problem,
then contact your Digital Projection dealer or service centre.
Rev A October 2010 Page 7.3
Page 54
7. Appendix Digital Projection HIGHlite 6000 User Manual
Error codes
Iftheprojectordetectsanerror,theredIssueindicatorwillflash,asshowninthe
chart below.
Forexample,ifthelampdoorisleftopen,theredindicatorwillflashtwicefollowed
by a pause, then the sequence will repeat until the error condition is corrected.
Notes
Page 7.4 Rev A October 2010
Page 55
Digital Projection HIGHlite 6000 User Manual 7. Appendix
Specifications
Part numbers
Projector 110-914
0.77:1fixedlens 110022HConly
1.16:1 fixed lens 110-023 HC only
1.45–1.74:1 zoom lens 110-017 HC 110-803 HB
1.74–2.17:1 zoom lens 110-018 HC 110-804 HB
2.17–2.90:1 zoom lens 110-019 HC 110-805 HB
2.90–4.34:1 zoom lens 110-020 HC 110-806 HB
4.34–6.76:1 zoom lens 110-021 HC 110-807 HB
Power cable 10A, Europe 102-163
Power cable 13A, North America 102-165
Power cable 10A, United Kingdom 102-180
Remote control 110-024
User manual on CD 111-339
Replacement parts
Lamp module 330W 111-100
Optical
Digital Light Processor 3 x 0.65” Texas Instruments DMD™, resolution 1920 x 1080 pixels
Contrast Ratio 2000:1 (±10%)
Colour temperature Native: 7500K (±1500K), adjustable: 5500K 9300K
Pixelfillfactor 87%
Lamp power 330W
Lamp life (typical) 2000 hours
Brightness 6000 ANSI lumens (±10%)
Uniformity 85%
Rev A October 2010 Page 7.5
Page 56
7. Appendix Digital Projection HIGHlite 6000 User Manual
Lens shift (zoom lenses only)
Vertical ± 0.6 H (120%)
Horizontal ± 0.15 W (30%)
Electrical
Inputs HDMI x 2
Pixel clock (digital) up to 165MHz
Control inputs 1 x RS232 serial: 38400 baud, 8 bits, 1 stop bit, no parity
1 x RJ45 Ethernet Port
1 x remote control (via infra red)
Mains voltage 100 - 240 VAC ±10%, 47 - 63Hz (single phase)
Power consumption
110V 500W in Running mode, <2W in Standby
240V 450W in Running mode, <2W in Standby
International Regulations Meets FCC Class B requirements
Meets EMC Directives (EN 55022, EN 55024)
Meets Low Voltage Directive (EN60950)
Indicators Power, Standby, Issue (Fault)
Physical
Temperature
Operating 10 to 35°C
Storage 20 to 60°C
Thermal Dissipation 1800 BTU/hr
Humidity
Operating 20% to 90% non condensing
Storage 10% to 90%
Altitude
Operating up to 10,000 feet
Storage up to 40,000 feet
Weight 26 kg
Noise level < 37dBA
Specificationsaresubjecttochangewithoutnotice.
Page 7.6 Rev A October 2010
Page 57
Digital Projection HIGHlite 6000 User Manual 7. Appendix
Dimensions
All dimensions in mm
unless otherwise stated
Rev A October 2010 Page 7.7
Page 58
7. Appendix Digital Projection HIGHlite 6000 User Manual
Video formats supported
Sign
al Type
PC
Resolution
640x480 59.94 x VESA DMT
640x480 74.99 x VESA DMT
640x480 85 x VESA DMT
800x600 60.32 x VESA DMT
800x600 75 x VESA DMT
800x600 85.06 x VESA DMT
848x480 47.95 x VESA CVT
848x480 59.94 x VESA CVT
1024x768 60 x VESA DMT
1024x768 75.03 x VESA DMT
1024x768 85.03 x
1024x768 70.1 x
1280x720 47.95 x
Rate
Y-Pr-Pb
S-Video
Video
HD15 - YUV
HD15 - RGBHV
HDMI - RGB
HDMI - YUV 8-bit
VESA DMT
VESA DMT
VESA GTF
HDMI - YUV 12-bit
HDMI - YUV 10-bit
Frame
References
1280 x 768
1280 x 768
1280 x 768
1280 x 768
1280 x 800 50.0
1280 x 800
1280 x 800 75.0
1280x1024 60.02 x VESA DMT
1280x1024 75.02 x VESA DMT
1280x1024 85.02 x VESA DMT
1440 x 900 60.0
1440 x 900 75.0
1400 x 1050 60.0
1400 x 1050 75.0
1600x1200 60 x VESA DMT
1920x1080 47.95 x VESA CVT
1600 x 1200
60.0
60.0
75.0
85.0
60.0
60.0 x VESA DMT
x VESA DMT
x VESA DMT Reduced Blanking
x VESA DMT
x VESA DMT
x
x VESA DMT
x VESA DMT
x VESA DMT
x VESA DMT
x VESA DMT
x VESA DMT
1920 x 1200
60.0 x Reduced Blanking
Page 7.8 Rev A October 2010
Page 59
Digital Projection HIGHlite 6000 User Manual 7. Appendix
Signal
Resolution
Type
Frame
Rate
References
Video
S-Video
Y-Pr-Pb
HD15 - RGBHV
HD15 - YUV
HDMI - RGB
HDMI - YUV 8-bit
HDMI - YUV 10-bit
HDMI - YUV 12-bit
1680x1050 59.94 x VESA CVT
640x480 66.59 x VESA DMTApple Mac
832x624 74.54 x VESA DMT
NTSC NTSC (M, 4.43) 59.94 ITU-R BT.1700, SMPTE 170M
PAL
PAL (B,G,H,I) 50 ITU-R BT.1700
PAL (N) 50 ITU-R BT.1700
PAL (M) 59.94 ITU-R BT.1700
SECAM SECAM (M) 50 ITU-R BT.1700
SDTV
RGBS 50 RS-170, ITU-R BT.656
480i 59.94 x x x x SMPTE 125M, CEA-861-D
576i 50 x x x x ITU-R BT.601, CEA-861-D
480p 59.94 x x x x SMPTE 293M, CEA-861-DEDTV
576p 50 x x x x
ITU-R BT.1358, CEA-861-D
HDTV
1035i 60 x x x x SMPTE 260M
1080i 50 x x x x SMPTE 274M, CEA-861-D
1080i (Aus) 50 x x x x SMPTE 295M
1080i 59.94 x x x x SMPTE 274M, CEA-861-D
1080i 60 x x x x SMPTE 274M, CEA-861-D
720p 50 x x x x
SMPTE 296M, CEA-861-D
720p 59.94 x x x x SMPTE 296M, CEA-861-D
720p 60 x x x x SMPTE 296M, CEA-861-D
1080p 23.98 x x x x SMPTE 274M, CEA-861-D
1080p 24 x x x x SMPTE 274M, CEA-861-D
1080p 25 x x x x SMPTE 274M, CEA-861-D
1080p 29.97 x x x x SMPTE 274M, CEA-861-D
1080p 30 x x x x SMPTE 274M, CEA-861-D
1080p 50 x x x x SMPTE 274M, CEA-861-D
1080p 59.94 x x x x SMPTE 274M, CEA-861-D
1080p 60 x x x x SMPTE 274M, CEA-861-D
Rev A October 2010 Page 7.9
Page 60
7. Appendix Digital Projection HIGHlite 6000 User Manual
Input connections
HDMI 1 & 2 inputs
19 way type A connector
1 TMDS Data 2+
2 TMDS Data 2 Shield
3 TMDS Data 2-
4 TMDS Data 1+
5 TMDS Data 1 Shield
6 TMDS Data 1-
7 TMDS Data 0+
8 TMDS Data 0 Shield
9 TMDS Data 0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CEC
14 not connected
15 SCL (DDC Clock)
16 SCA (DDC Data)
17 DDC/CEC Ground
18 +5 V Power
19 Hot Plug Detect
Notes
pin view of panel connector
Page 7.10 Rev A October2010
Page 61
7. Appendix Digital Projection HIGHlite 6000 User Manual
Control connections
Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a modem)
RX 2 3 TX
TX 3 2 RX
GND 5 5 GND
pin view of female connector
Notes
The projector is a DCE, so use:
a straight cable to connect to a
·
computer, or
a nullmodem cable as shown
·
here to connect to another DCE
such as a modem.
Serial port settings
Baud rate 38400 bps
Data length 8 bits
Stop bits one
Parity none
Flow control none
Page 7.11 Rev A October 2010
Page 62
Digital Projection HIGHlite 6000 User Manual 7. Appendix
Remote communications protocol
Introduction
The projector can be controlled by using an external control system or a PC via an
RS232 serial interface or RJ45 Ethernet connection on port 7000, using a terminalemulation program, such as HyperTerminal.
There are 2 types of commands:
·
Key commands
·
Operation commands
All commands consist of ascii text strings starting with 2 letters:
·
ky for key commands.
·
op for operations commands.
All commands end with an ascii Carriage Return character.
Key Commands
Key commands are used to simulate remote control key presses, and use the
following format:
ky <keyname> [CR]
Notes
Details of how to connect to
the projector, using the serial
control input, can be found
earlier in this section.
Example
ky pow.on [CR] simulates the POWER ON key being pressed.
The commands
Code transmitted <keyname> Description
0x01 pow.on Turn power on.
0x09 pow.off Turn power off.
0x18 cur.down Keypad down arrow.
0x1A cur.up Keypad up arrow.
0x1D cur.left Keypad left arrow.
0x1F cur.righ Keypad right arrow.
0xAD pattern.sw Switch to the next test pattern.
Note: in the example, spaces
are included for clarity, but are
not necessary in the actual
command.
Rev A October 2010 Page 7.12
Page 63
Digital Projection HIGHlite 6000 User Manual 7. Appendix
Operation Commands
Operation commands are used to simulate menu operations and determine the
settings of the projector, and use the following format:
op <operation> <command> [CR]
The <command> string can take one of the following formats:
<command> Description
Set = <value> Makes the setting take that value.
Get ? Asks what the current value is.
The value is returned as an ascii text string.
Increment + Adds 1 to the current value.
Decrement - Subtracts 1 from the current value.
Execute (none) Performs an action.
Example
op bright + [CR] increments the brightness setting.
op model.name ? + [CR] returns the model name of the projector.
The commands
Operation <command> Values Notes
bright = ? + - 0 - 200
contrast = ? + - 0 - 200
model.name ? <string>
ser.number ? <string>
soft.version ? <string>
lamp.hours ? <number>
total.hours ? <number>
environment ? <string> Temperatures
0 = standby mode
1 = warm up mode
status.check ?
pattern =
2 = running mode
3 = cooling mode
4 = error
0 = White
1 = Black
2 = Red
3 = Green
4 = Blue
5 = Cyan
6 = Magenta
7 = Yellow
8 = Chequerboard
9 = Greyscale
10 = Alignment Grid
11 = Off
Notes
Note: in the examples, spaces
are included for clarity, but are
not necessary in the actual
command.
Rev A October 2010 Page 7.13
Page 64
7. Appendix Digital Projection HIGHlite 6000 User Manual
Operation <command> Values Notes
LFN Lens Focus Near
LFF Lens Focus Far
LZI Lens Zoom In
LZO Lens Zoom Out
LPD Lens Shift Down
LPU Lens Shift Up
LPL Lens Shift Right
LPR Lens Shift Left
LS Lens Stop Movement
Page 7.14 Rev A October 2010
Loading...