Digital Finishing Group Office ECoil46 User Manual

Power Roller Binding

Office ECoil46 – Manual Punch and Power Coil Binding Machine

Large Trash Drawer Foot Pedal operated

Open Punch Throat

For punching larger

Features extra DURABLE roller

P

unch Handle

High strength die cast metal

At back side of machine

Full Die Disengagement Pins

For clean and complete punching

Not shown

d

ocument sizes

with different paper sizes

Side Margin Control

For evenly centered
document punching

Punch Margin Control

Maximizes the tear resistance

of all documents

Sturdy Die Cast Metal Construction

For many years of worry free operation

Non Skid Feet Punching Capacity

Up to 12-15 sheets (20 lbs)

Digital Finishing Group

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone:[phone], Fax: [phone]

Email: [e-mail]

Website: www.dfgus.com

Warning:

Do not connect this product to electrical power or attempt to operate it before you
read these operating instructions and have been fully trained to operate this product.

1. Indoor use only. Do not expose to rain.

2. Keep hands, long hair, neckties, necklaces and other loose articles away from

roller.

3. Do not place this product on an unstable stand, cart, or surface. The product may

fall and hurt you. If you use a cart, move the product and cart carefully.

4. Do not insert objects or spill liquids into the product. They may short out

components that may result in fire.

5. The power outlet shall be installed near this product and shall be easily accessible.

6. Unplug the product before moving it. Unplug the power supply when it will not

be in use for an extended period of time.

7. Do not attempt to service this product. Contact your DFG or your dealer if you

need service.

8. In case you need to replace fuse, please use 3.0 A fuse.

9. Do not operate the machine when the cover is not on the machine.

This machine should only plug into 110 V single-phase power outlets. When
using the roller, some motor and roller noises are normal. Roller is tested to last
10,000+ binding. We provide one-year part and labor warranty for this machine.

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone:[phone], Fax: [phone]

Email: [e-mail] Website: www.dfgus.com

Dear Customer,

Thank you for purchasing our Office ECoil46 (EC46) machine. The following are basic
installation and operation instruction for the EC46 machine. If you still have questions
after reading this manual, please contact DFG.

Installation

Remove the blue knob from machine. Slide the punch handle on the exposed knob. Screw
the blue knob back onto machine. Connect power cord and connect the foot pedal.

Remove the blue
knob

How to Punch

Install the punch handle
and blue knob

Connect foot pedal and
power cord (not shown)

1. Set the side guide to center the
sheet for punching

2. Select the punch margin (tip – the
thicker the book, the larger the punch
margin can be. However, you can use
a small punch margin for any book)

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone:[phone], Fax: [phone]

Email: [e-mail] Website: www.dfgus.com

3. Make sure your sheets are all the
way inside, against the back wall, and
then move sheets to the left side
against the side guide. Pull the punch
handle to punch the sheets.

How to Bind Books with Power Roller (up to 3/4”)

1. Manually turn the spiral coil into
the first 4 or 5 holes

2. Press the foot pedal. Touch the
coils against the moving roller to spin
the coil through the book. (Tip - You
can speed up binding by moving the
book to the right side while the roller
is spinning the coil through the book)

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone:[phone], Fax: [phone]

Email: [e-mail] Website: www.dfgus.com

3. Cut and crimp the ends of the
spiral coil.
Right handed

A. Hold pliers with red dot up,

with the coil near you.

B. Place pliers with jaws inside

the coil, near the center.

C. Close the pliers to cut the coil

and keep them closed

D. Optionally twist pliers to bend

crimp more before releasing

E. Release coil, flip the book

over sideways and crimp the
other side using the same
procedure (coils still near
you)

Left handed
Use pliers as described above but
hold them in your left hand and put
the red dot down.

1260 Kempar, Madisong Heights, MI 48071, U.S.A. Phone:[phone], Fax: [phone]

Email: [e-mail] Website: www.dfgus.com

How to Make Books Manually for any thickness (EtitanCoil machine
showed)

Manually turn your coil into the
book. This is a very easy process.
(Tip: It will be much easier to twist
the front end of coils)

Cut and crimp the coils (see #3 of
power roller binding)

How to Determine Appropriate Coil Size

There are two ways you can choose an appropriate coil size:

1. Use any size coil you like, as long as the coils size is larger than book thickness

2. Use coil that is 2 – 6 mm (1/8” to ¼”) larger than book thickness

Specification:

Punch: Max. 15 sheets of paper (20 lbs), 6-12 Normal
Punch size: Any size
Binding Size: Electric power binding up to 3/4". Manual binding to any size.
Electrical Coil Binding: up to 3/4”
Side Margin Control: Lets you center holes quickly and easily for perfect alignment
Punch margin control: Provide strongest binding for any book size
Open Throat: For punching any larger book length

1260 Kempar, Madisong Heights, MI 48071, U.S.A. Phone:[phone], Fax: [phone]

Email: [e-mail] Website: www.dfgus.com